Thermador KBULT3655E User Manual [en, es, fr]

INSTALLATION INSTRUCTIONS

For Built-in Refrigerators

INSTRUCCIONES DE

Bottom Mount Models/ Modelos con montaje inferior/ Modèles superposés KBULT3655E, KBURT3655E

INSTALACIÓN

Para los refrigeradores empotrados

INSTRUCTIONS D’INSTALLATION

Pour réfrigérateurs encastrés

KBULT3665E, KBURT3665E KBULT3675E, KBURT3675E

2327571A

TABLE OF CONTENTS

REFRIGERATOR SAFETY .............................................................3

DESIGN SPECIFICATIONS............................................................4

Models..........................................................................................4

Product Dimensions.....................................................................5

Tipping Radius .............................................................................6

Door Swing Dimensions...............................................................6

Handle and Door Clearances for Custom Panel Series ..............7

Custom Panels.............................................................................9

Full-Overlay Custom Panels ......................................................10

Stainless Steel Series Side Panels ............................................10

Custom Panel Series Side Panels .............................................11

INSTALLATION REQUIREMENTS..............................................12

Tools and Parts ..........................................................................12

Location Requirements..............................................................13

Electrical Requirements .............................................................14

Water Supply Requirements......................................................14

ÍNDICE

SEGURIDAD DEL REFRIGERADOR...........................................22

ESPECIFICACIONES DE DISEÑO ..............................................23

Modelos......................................................................................23

Medidas del producto................................................................24

Arco de vuelco ...........................................................................25

Medidas de oscilación de la puerta...........................................25

Espacios para la agarradera y la puerta para

la serie de paneles a la medida..................................................26

Paneles a la medida...................................................................28

Paneles a la medida totalmente recubiertos .............................29

Paneles laterales de la serie de acero inoxidable......................30

Paneles laterales a la medida para la serie

de paneles a la medida..............................................................30

REQUISITOS DE INSTALACIÓN.................................................31

Piezas y herramientas................................................................31

Requisitos de ubicación.............................................................32

Requisitos eléctricos..................................................................33

Requisitos del suministro de agua.............................................33

INSTALLATION INSTRUCTIONS ................................................15

Unpack the Refrigerator.............................................................15

Reduce Tipping Radius..............................................................15

Move the Refrigerator into House..............................................16

Install Anti-Tip Boards................................................................16

Connect the Water Supply.........................................................17

Plug in Refrigerator.....................................................................18

Move Refrigerator to Final Location...........................................18

Lower Leveling Legs ..................................................................18

Install Custom Panels.................................................................19

Level Refrigerator .......................................................................20

Adjust Door Swing......................................................................20

Install Side Panel........................................................................20

Install Base Grille........................................................................21

Water System Preparation.........................................................21

Complete Installation..................................................................21

INSTRUCCIONES DE INSTALACIÓN.........................................34

Cómo desempacar su refrigerador............................................34

Cómo reducir el arco de vuelco.................................................34

Cómo hacer entrar el refrigerador en la casa ............................35

Cómo instalar los tableros antivuelco........................................35

Conexión del suministro de agua ..............................................36

Cómo enchufar el refrigerador ...................................................37

Ubicación final del refrigerador..................................................37

Baje las patas niveladoras .........................................................37

Cómo instalar los paneles a la medida......................................38

Cómo nivelar el refrigerador.......................................................39

Cómo ajustar la oscilación de las puertas.................................39

Cómo instalar el panel lateral.....................................................39

Cómo instalar la rejilla de la base ..............................................40

Preparación del sistema de agua ..............................................40

Cómo terminar la instalación .....................................................40

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................41

SPÉCIFICATIONS DE DESIGN....................................................42

Modèles......................................................................................42

Dimensions du produit...............................................................43

Rayon de basculement ..............................................................44

Dimensions pour le pivotement des portes...............................44

Dégagements pour les poignées et portes

pour la série de panneaux personnalisés..................................45

Panneaux personnalisés............................................................47

Panneaux personnalisés à recouvrement complet ...................48

Panneaux latéraux de la série de panneaux

en acier inoxydable ....................................................................49

Panneaux latéraux de la série de panneaux personnalisés......50

EXIGENCES D’INSTALLATION...................................................51

Outillage et pièces......................................................................51

Exigences d’emplacement.........................................................51

Spécifications électriques .........................................................52

Spécifications de l’alimentation en eau.....................................53

INSTRUCTIONS D’INSTALLATION.............................................53

Déballage du réfrigérateur..........................................................53

Réduction du rayon de basculement.........................................54

Faire entrer le réfrigérateur dans le domicile .............................54

Installation de planches antibasculement..................................55

Raccordement à la canalisation d'eau.......................................55

Brancher le réfrigérateur.............................................................56

Déplacement du réfrigérateur à l'emplacement final.................57

Déploiement des pieds de nivellement......................................57

Installation des panneaux personnalisés...................................57

Nivellement du réfrigérateur.......................................................58

Ajustement de l’ouverture des portes........................................59

Installation du panneau latéral ...................................................59

Installation de la grille de la base...............................................60

Préparation du système d’eau...................................................60

Achever l’installation ..................................................................60

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

follow instructions.

can be killed or seriously injured if you don't

You instructions.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

DESIGN SPECIFICATIONS

Models

Stainless Steel Series

Features stainless steel exterior styling with professional-look door handles.

KBULT3661A KBURT3661A KBULT3655E KBURT3655E KBULT3665E KBURT3665E

TRIMKITBM - Trimless Trim Kit

On the Custom Panel Series, you can create a “frameless” look using full-overlay custom panels. You will need to order a Trimless Trim Kit for 36" Bottom Mounts TRIMKITBM. This accessory kit contains parts to replace the factory trim.

Full-overlay custom panels and handles are required but not included in the accessory kit. Create the panels according to the specifications in the “Full-Overlay Custom Panels” section. You can order a set of Thermador’s Curved Handles or select handles from other sources. For door clearances, see “Handle and Door Clearances for Custom Panel Series.”

Custom Panel Series

Features factory-installed, traditional style trim to provide a “framed” look. This series requires the installation of custom panels that are not included.

KBULT3675E KBURT3675E

Handle Kits

For use with Stainless Steel models. You can purchase a handle type other than that provided with your model. See your dealer for Details.

CURVHNDL10 - Curved Handle Kit PROHNDL160 - Pro Handle Kit PROHNDL165 - Designer Pro Handle Kit MASTHNDL55 - Masterpiece Handle Kit

EXTHANDBM - Extended Handle Kit for 36" Bottom-mount

This kit may be required if you insatll a custom raised panel. See “Handle and Door Clearances for Custom Panel Series.”

Product Dimensions

Side View

■ The depth from the front of the top grille to the back of the

refrigerator cabinet is 25³⁄₈" (64.5 cm).

■ The power cord is 84" (213 cm) long.

■ The water line attached to the back of the refrigerator is 5 ft

(1.5 m) long. Height dimensions are shown with leveling legs extended ¹⁄₈" (3 mm) below the rollers.

25³⁄₈"

(64.5 cm)

23¹⁄₂"

(59.7 cm)

*83³⁄₈"

(211.8 cm)

84" (213.4 cm) Power Cord

42" (106.7 cm) Models

¹⁄₄"

(105 cm)

25³⁄₈" (64.5 cm)

Front View

■ Width dimensions were measured from trim edge to trim

edge.

■ Height dimensions are shown with leveling legs extended ¹⁄₈"

(3 mm) below the rollers.

36" (91.4 cm) Models

¹⁄₂" (8.9 cm)

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Top Vie w

36" (91.4 cm) Models

35¹⁄₄"

(89.5 cm)

25³⁄₈" (64.5 cm)

*83³⁄₈" (211.8 cm)

36¹⁄₄" (92 cm)

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

42" (106.7 cm) Models

*83³⁄₈" (211.8 cm)

42¹⁄₄" (107.3 cm)

*When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions.

Door Swing Dimensions

The location must permit the door to open to a minimum of 90°. Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the refrigerator and a corner wall.

NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended handles on a Classic model.

To adjust the door swing, see “Adjust Doors.”

36" (91.4 cm) Models

23"

(58 cm)

51"

(130 cm)

59"

(150 cm)

90˚

110˚

130˚

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

■ The dolly wheel height must be added to the tipping radius

when a dolly is used.

■ If needed, the tipping radius can be reduced. See “Reduce

Tipping Radius.”

Side Tipping Radius

90¹⁄₂"

(229.9 cm)

A. Tip this side only

Handle and Door Clearances for Custom Panel Series

If you are installing custom panels, the panels must allow certain clearances for the handles and for the doors to swing open. An Extended Handle Kit may be required if you install a custom raised panel. See the “Models” section under “Design Specifications.”

Door

Custom Panel Series Handle

Optional Extended Handle

(2.5 cm)

Custom Panel

(5.1 cm)

(7.6 cm)

Handle Dimensions Actual Size

/4" (6.35 mm)

/2" (1.3 cm)

/4" (1.9 cm)

1" (2.5 cm)

/4" (3.2 cm)

/2" (3.8 cm)

/4" (4.4 cm)

2" (5.1 cm)

/4" (5.7 cm)

/2" (6.4 cm)

/4" (7 cm)

3" (7.6 cm)

Custom Panel Series Clearances for Full-Overlay Custom Panels

Door Swing 110˚ Actual Size

Hinge

Refrigerator Side Trim

(1.3 cm)

/4"

(6.35 mm)

/2"

(1.3 cm)

/4"

(1.9 cm)

(2.5 cm)

/4"

(1.9 cm)

/2"

(3.2 cm)

/4"

(4.4 cm)

/2"

(3.8 cm) /4"

/4" (6.35 mm)

/2" (1.3 cm)

/4" (1.9 cm)

(5.1 cm)

1" (2.5 cm)

/4" (3.2 cm)

/2" (3.8 cm)

NOTE: To use full-overlay custom panels, you must order the Trimless Trim Kit. Additionally, you will need to order either a set of Thermador's Handles or select handles from another source. See the “Models” section of “Design Specifications” for more information and specific kit.

Door

(2.5 cm)

Backer Panel

Custom Panel

Spacer Panel

/4"

(3.2 cm)

/2"

1 (3.8 cm)

Custom Panels

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or carpenter. See dimension drawings for panel specifications.

IMPORTANT: Panels weighing more than recommended may cause damage to your refrigerator.

NOTE: Dimensions shown have a (±) ¹⁄₁₆" (1.5 mm) tolerance. Panels that are more than ¹⁄₄" (6.35 mm) thick must be routed. If panels are less than ¹⁄₄" (6.35 mm) thick, install a filler panel between the door and the decorative panel.

Top Grille Panel

The top panel should not weigh more than 10 lbs (4.5 kg) total weight.

34¹⁄₂"

(87.63 cm)

7¹⁄₄" (18.4 cm)

Refrigerator and Freezer Panels

The freezer panel should not weigh more than 30 lbs (13.5 kg) total weight. The refrigerator panel should not weigh more than 60 lbs (27 kg) total weight.

34¹⁄₄"

(87 cm)

Top Grille Panel – Routing Requirements

Top and bottom edges of the top panel should be edge routed ¹⁄₂" (1.3 cm) and ³⁄₈" (9.5 mm), respectively. Both ends should be edge-routed ⁷⁄₈" (2.2 cm) as shown.

¹⁄₄"

(6.35 mm)

max.

⁷⁄₈"

(2.2 cm)

Top Grille

Top

Grille

⁷⁄₈"

(2.2 cm)

NOTE: When creating a panel with face detail, the offsets will be hidden and must be accounted for in order to center the detail in the top grille.

¹⁄₄"

(6.35 mm) max.

¹⁄₂"

(1.3 cm)

min.

Top

¹⁄₄

" (6.35 mm) max.

34¹⁄₄"

(87 cm)

49" (124.5 cm)

20¹⁄₈" (51.1 cm)

Center face

detail between

offsets

³⁄₈"

(9.5 mm)

min.

Bottom

¹⁄₄"

(6.35 mm) max.

Door Panel – Routing Requirements

If an extended handle kit is used, then routing the handle side of the door and drawer panels is not required. See “Handle and Door Clearances for Custom Panel Series” for more information on ordering extended handles.

If the standard handle is used, route the entire handle side 3¹⁄₄" (8.25 cm) to allow for finger clearance. Then route the other side 1" (2.54 cm).

Standard Handle – Top View

3¹⁄₄"

(8.25 cm)

min.

Hinge Side

¹⁄₄" (6.35 mm) max.

Handle

2" (5 cm)

min.

Door Panel

(2.54 cm)

Door Panel - Side View

¹⁄₂" (1.3 cm)

min.

¹⁄₄"

(6.35 mm) max.

Panel

Full-Overlay Custom Panels

Custom overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen décor and to use custom handles for additional design flexibility.

NOTE: To use full-overlay custom panels, a Trimless Trim Kit for 36" Bottom-mounts is required (TRIMKITBM). Full-overlay custom panels and handles are required but not included. Create the panels according to these specifications. You may order Thermador’s Curved Handle Kit (CURVEDHAND) or select handles from another source. See the “Models” section under “Design Specifications” for additional information.

The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the following graphic: a decorative overlay panel, a ¹/₈" (3.18 mm) spacer panel or spacer strips and a ¹/₄" (6.35 mm) backer panel.

To minimize panel weight, you may use 2" (5.08 cm) spacer strips around the perimeter in place of full-sheet solid spacer panels. The spacer strips must be set in at least 1" (2.54 cm) from the top, bottom and sides edges of the backer panel. If you use spacer strips, it is also recommended that you use two - 2" (5.08 cm) strips horizontally centered for added support.

35³⁄₈"

(89.85 cm)

³⁄₈"

8¹⁄₂"

(21.59 cm)

(127.0 cm)

50"

(18.73 cm)

49¹⁄₈"

(124.78 cm)

34⁵⁄₈" (87.95 cm)

34¹⁄₂"

(87.63 cm)

34⁵⁄₁₆"

(87.15 cm)

Bottom Offset

⁷⁄₁₆" (11.1 mm)

Center Backer Panel left to right

Bottom Offset 1" (2.54 cm)

Center Backer Panel left to right

Overlay Panel

/8" to 3/4"

(15.88 to

19.05 mm) (3.18 mm)

/8"

Spacer Panel

Backer Panel

/4"

(6.35 mm)

Spacer Panel

/8"

(3.18 mm)

1" minimum (2.54 cm)

Offset Dimension

Door/Grille Trim

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom overlay panels will fit properly.

IMPORTANT:

■ The total weight of the refrigerator door overlay panel cannot

exceed 60 lbs (23 kg).

■ The total weight of the freezer drawer overlay panel cannot

exceed 30 lbs (13.5 kg).

■ The total weight of the top grille overlay panel cannot exceed

10 lbs (4.5 kg).

34¹⁄₂"

(87.63 cm)

20⁹⁄₁₆"

(52.23 cm)

34⁵⁄₁₆"

(87.15 cm)

20³⁄₁₆"

(51.28 cm)

Center Backer Panel left to right

Bottom Offset

¹⁄₁₆" (1.6 mm)

Stainless Steel Series Side Panels

Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation.

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions

and may not reflect the needed panel installation dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on the rear wall.

Refrigerator

Recessed Inset Installation Dimensions

24¹⁄₈"

(61.3 cm)

23¹¹⁄₁₆"

(60.3 cm)

¹⁄₂"

(59.7 cm)

Side Trim

¹⁄₄"

(6.35 mm)

¹¹⁄₆₄"

(4.5 mm)

³⁄₁₆"

(4.7 mm)

⁷⁄₃₂"

(5.5 mm)

¹³⁄₃₂" (10 mm)

⁵⁄₈"

(15.7 mm)

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ⁷⁄₃₂" (5.6 mm) to this measurement to allow the side panel to fit into the trim.

2. If the panel is more than ¹⁄₄" (6.35 mm) thick, route the front

edge to allow the side panel to fit into the trim.

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a ¹⁄₄"

(6.35 mm) board to hold the panel in the cabinet side trim.

Custom Panel Series Side Panels

Refrigerator and Side Trim Dimensions

The width and height of a side panel are determined by the type of installation you are planning.

NOTES:

■ The dimensions shown are actual product dimensions

and may not reflect the needed installation dimensions.

■ The side panel should be a minimum of ½" (1.27 cm) thick

to avoid warping.

■ If the opening depth is 25" (63.5 cm) or more, you may

want to install a support board on the rear wall.

Refrigerator

Overlay

23³⁄₈"

(59.40 cm)

Flush Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall.

2. Attach the support board with a screw or adhesive that is

compatible with aluminum and wood.

Side Trim

³⁄₈"

(9.7 mm)

¹⁄₁₆"

(1.5 mm)

¹⁄₈"

(3.2 mm)

³⁄₁₆"

(4.5 mm)

2. If the panel is more than ³⁄₈" (9.5 mm) thick, route the front

edge to allow the side panel to fit into the trim.

Recessed Inset Installation Dimensions

1. Measure the distance from point A (as shown) to back wall.

2. Route the front edge of the support board or attach a ³⁄₈"

(9.5 mm) board to hold the panel in the cabinet side trim.

Inset Installation Dimensions

1. Measure the distance from point A (as shown) to the back

wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side panel to fit into the trim.

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Installer: Leave Installation Instructions with the homeowner.

■ Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local electrical inspector’s use.

Too ls n ee ded:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Hand drill or electric drill

(properly grounded)

■ Drill bits

■ Adjustable wrenches (2)

■ Phillips screwdriver

■ Small level

■ Appliance dolly

■ T27 Torx

■ ¹¹⁄₃₂" nut driver

■ ³⁄₈" and ¹⁄₂" open-end

wrenches

■ ⁵⁄₃₂" Allen wrench

■ ⁵⁄₁₆" socket wrench

■ Tape measure

®†

screwdriver

Parts needed:

■ #8 x 3" (7.6 cm) or longer wood screws (6)

■ 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board (1 or 2)

■ Make custom or overlay panels or consult a qualified

cabinetmaker or carpenter to make the panels. See “Design Specifications.”

■ If you are connecting the water line directly to copper tubing

and not to a shutoff valve, you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting.

†®TORX is a registered trademark of Textron Innovations Inc.

Location Requirements

The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

■ Observe all governing codes and ordinances.

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

■ Do not install in a location where the temperature will fall

below 55°F (13°C).

■ Floor must support the refrigerator weight, more than 600 lbs

(272 kg), door panels and contents of the refrigerator.

■ Ceiling height must allow for side tipping radius. See “Tipping

Radius.”

■ Location should permit door to open fully. See “Door Swing

Dimensions.”

■ Location must permit top grille removal. See “Opening

Dimensions.”

■ A grounded 3 prong electrical outlet should be placed within

4" (10.2 cm) of the right side cabinets or end panel. See “Electrical Requirements” for additional information.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See “Water Supply Requirements” for more specific information.

80" - 90"

(203-229 cm)

83¹⁄₂" (212.1 cm) min.

³⁄₄" (215 cm) max.

84 to bottom of solid soffit

Width

(see chart following)

(10.2 cm)

77" (196 cm)

Opening Dimensions

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs 80" to 90" (203 to 229 cm) above the floor. See “Install Anti-Tip Boards” for more information.

NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained in front of the refrigerator’s side trim in order for the top grille to be removed.

¹⁄₂"

(1.3 cm)

(15.2 cm)

24"

(2.54 cm)

(15.2 cm)

(60.96 cm) min.

Model Width A (as shown above)

36 42

35¹⁄₂" (90.2 cm) 41¹⁄₂" (105.4 cm)

NOTE: Flooring under refrigerator must be at same level as the room.

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker box.

When you are finished, turn ON the master power switch or reconnect power at the circuit breaker box. Then reset the control to the desired setting.

Water Supply Requirements

■ All installations must meet local plumbing code requirements.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. The right-hand side is recommended. The access hole through the cabinet must be within ¹⁄₂" (12.7 mm) of the rear wall.

NOTE: If the water shut off valve is in the back wall behind the refrigerator, it must be at an angle so that the tube is not kinked when the refrigerator is pushed into its final position.

(15.2 cm)

■ If the water shutoff valve is not in the cabinets, the plumbing

24"

(60.96 cm) min.

(2.54 cm)

(15.2 cm)

for the water line can come through the floor. A ¹⁄₂" (12.7 mm) hole for plumbing should be drilled at least 6" (15.2 cm) from the right or left hand side cabinet or panel. On the floor, the hole should be no more than 1" (2.54 cm) away from the back wall. See “Connect the Water Supply.”

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs more easily. NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

■ Do not remove the protective film until the refrigerator is in its

operating position.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

■ Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating position.

1. Remove and save the literature package and parts bag taped

to the refrigerator door. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

2. If necessary, reduce the tipping radius. See “Tipping Radius”

for ceiling height requirements or “Reduce Tipping Radius” for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to “Move the Refrigerator into House.”

Reduce Tipping Radius

(if required)

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius” in the “Design Specifications” section for more information.

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

36" (91.4 cm) 88" (223.5 cm)

Custom Panel Series

1. Grasp both ends of the top grille.

2. Push the top grille straight up; then pull straight out. Lay the

grille on a soft surface.

B BA

A. Top grille B. Cabinet side trim

3. Remove the six screws attaching each cabinet side trim to

the refrigerator and remove the side trims.

Stainless Steel Handle Series

1. Grasp both ends of the top grille. Push the top grille straight

up; then pull straight out. Lay the top grille on a soft surface.

B BA

A. Top grille

B. Cabinet side trim

2. Remove the six screws attaching each cabinet side trim to

the refrigerator and remove the side trims.

Move the Refrigerator

into House

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure do so can result in death or serious injury.

3. Place an appliance dolly under the left side of the refrigerator

as shown. Be sure to protect the side trims and handles. Place the corner posts from the packing materials over the trims and handles as appropriate. Slowly tighten the strap.

NOTE: Pass the dolly strap under the handles for the Curved and Professional Series.

Install Anti-Tip Boards

IMPORTANT:

■ To avoid tipping during use, the solid soffit must be within 1"

(2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

■ It is recommended that board(s) be installed before the

refrigerator is installed.

■ Board(s) must be long enough to fully cover the width of the

compressor cover.

■ Locate the board(s) so the bottom surface(s) of the board(s)

is(are) 84" (213 cm) from the floor.

■ During installation, raise the refrigerator up so there is ¹⁄₄"

(6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to

229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1½" (3.8 cm). The board(s) must overlap the compressor cover.

4. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

5. Place top of cardboard carton or plywood under refrigerator.

Remove dolly.

6. Do not remove protective film or cover.

7. If necessary, reassemble the trim and top grille after the dolly

has been removed from the refrigerator.

2" (5 cm)

A. Center board B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

¹⁄₄

" (6.35 mm) max. above refrigerator

Connect the Water Supply

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFF.

Style 1 - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1,

see “Style 2 - Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply. IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the shutoff valve as shown.

A. Bulb B. Nut C. Water tubing

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. Plug in the refrigerator or reconnect power.

7. Flush the water system. See “Water System Preparation.” NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill ice container.

Style 2 - Copper Line Connection

Connecting to Water Line

NOTE: If existing water line meets the “Water System

Requirements,” see “Connecting to Refrigerator.”

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

DEF

A. Cold water pipe B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve F. Sh u to f f va l ve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten, or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

8. Turn off the shutoff valve on the water pipe. Coil the copper

tubing.

9. Check for leaks around the saddle valve.

Connecting to Refrigerator

1. Unplug the refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Measure the distance from the shutoff valve to the opening in

which the refrigerator will be located. Tubing must be extended from the shutoff valve into the refrigerator opening following specific guidelines. See “Water Supply Requirements.”

4. A ¹⁄₄" x ¹⁄₄" (6.35 mm to 6.35 mm) coupling is needed in order

A B

to connect the water tubing to an existing household water line. Thread the provided nut onto the coupling on the end of the copper tubing.

A B C D E F G

A. Water tubing B. Nut C. Bulb D. Coupling (purchased)

5. Turn shutoff valve ON.

6. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

7. Plug in the refrigerator or reconnect power.

8. Flush the water system. See “Water System Preparation.” NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill ice container.

E. Ferrule (purchased) F. Nut (purchased)

G. Household water line (as

connected in previous section)

Plug in Refrigerator

WARNING

Move Refrigerator to Final

Location

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: To avoid floor damage, make sure levelers are raised (not touching floor) and refrigerator is on rollers before moving.

1. Place top of cardboard carton or plywood under refrigerator.

Remove dolly.

2. Do not remove protective film or cover.

3. Move the refrigerator straight back and evenly into the

opening. Be sure that the refrigerator side trims are not interfering with the door opening. Also, be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

Lower Leveling Legs

NOTE: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

Use a ⁵⁄₁₆" socket wrench to turn the leveling bolts clockwise to lower the 4 leveling legs until refrigerator weight is supported by leveling legs. The rollers should be off the floor. To avoid cabinet damage, do not apply more than 50 inch-pounds (58 cm - kg) of torque to the leveling legs.

A B

A. Rear leveling legs B. Front leveling legs

+ 42 hidden pages