Thermador IT30R Design Guide

Sub-Zero Design Guide

REVISED 8/ 2015

Contents

3 Built-In Refrigeration

38 PRO 48 Refrigeration

44 Integrated Refrigeration

54 Wine Storage

84 Undercounter Refrigeration

94 Sub-Zero Warranties

Features and specications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information.

IMPORTANT NOTE: Throughout this guide, dimensions may

1

vary by ±

/8" (3). Dimensions in parentheses are millimeters

unless otherwise specied.

BUILT-IN REFRIGERATION

Built-In Refrigeration

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

For the built-in line, Sub-Zero designers and engineers took a fresh look at everything, inside and out. Exterior renements include redesigned grilles and lower-prole hinges. Inside, new technology in food preservation makes the builtin line nothing short of revolutionary.

KEY FEATURES

• Four distinct design approaches: framed, overlay, ush

inset and stainless steel.

• Handle options coordinate with handles of Wolf cooking

products.

• Dual refrigeration; two compressors preserve food’s

goodness in two sealed compartments.

BUILT-IN MODELS

• Energy efcient; many models are ENERGY STAR®

qualied.

• Advanced water ltration and air purication systems.

• NEW! French door models requires less space for door

clearance to accommodate virtually any-size kitchen.

• NEW! Internal dispenser models provide chilled water

inside the refrigerator—some models also dispense ice.

• Crisper and deli drawers form a lower-temperature zone

for produce and meats.

• Flip-up grille provides easy access for quick routine

maintenance.

• All models are Star-K certied.

BI-36R BI-36RG BI-36F BI-30U BI-30UG BI-36U(ID) BI-36UG

BI-36UFD(ID) BI-42UFD(ID) BI-36S BI-42S(ID) BI-42SD BI-48S(ID) BI-48S

subzero.com/specs | 3

BUILT-IN REFRIGERATION

Built-In Design Options

FRAMED

For the classic Sub-Zero look, choose framed custom door panels that contrast with the stainless steel full-length handles and louvered grille (shown). The framed application is an overlay model with framed design features. Panel, grille and handle options are available.

Panels | Custom panels, stainless steel or white enamel.

Grille | Classic louvered grille insert or solid custom panel

for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations.

Handles | Full-length standard or extended.

OVERLAY

Custom overlay door panels can be combined with unique handle hardware for design exibility. Shown with pro handle option to complement Wolf ranges. Customize with panel, grille and handle options.

Panels | Custom panels or stainless steel.

Grille | Solid custom panel or pro louvered grille for 84"

(standard), 83" or 88" overall unit height. Dual wide grille for dual installations.

Handles | Custom, tubular or pro handles.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

Framed.

4 | Sub-Zero Customer Care 800.222.7820

Overlay.

BUILT-IN REFRIGERATION

Built-In Design Options

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

FLUSH INSET

The ush inset design option allows for ush door and grille panels and custom handle hardware. Shown with tubular handle option to match Wolf built-in ovens. The ush inset application is an overlay model with ush inset panels. Customize with panel, grille and handle options.

Panels | Custom panels or stainless steel.

Grille | Solid custom panel or pro louvered grille for 84"

(standard), 83" or 88" overall unit height. Dual wide grille for dual installations.

Handles | Custom, tubular or pro handles.

STAINLESS STEEL

For a professional look, classic stainless steel models require no customization. To complement the look of Wolf ranges, choose the pro handle option (shown). Grille and handle options are available.

Grille | Pro louvered grille for 84" (standard), 83" or 88" overall unit height. Dual wide grille for dual installations.

Handles | Tubular or pro handles.

Flush inset.

Stainless steel.

subzero.com/specs | 5

BUILT-IN REFRIGERATION

Overall Dimensions

ALL REFRIGERATOR / ALL FREEZER

HEIGHT DIMENSIONS ±

237/8"

(606)

36"

(914)

1

/2" (13)

733/4"

(1873)

141/8"

(359)

84"

(2134)

4" (102)

263/16"

237/8"

(665)

(606)

Overall dimensions are based on stainless steel models.

1

For ush inset applications, add

/2" (13) to door clearance

dimensions.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

371/4"

(946)

23/8" (60)

Model BI-36R, BI-36RG and BI-36F.

6 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

Overall Dimensions

OVER-AND-UNDER

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

HEIGHT DIMENSIONS ±

237/8"

(606)

30" (762)

263/16" (665)

84"

(2134)

503/4"

(1289)

23"

(584)

1

/2"

(13)

121/8"

(308)

4" (102)

237/8" (606)

HEIGHT DIMENSIONS ±

237/8"

(606)

36" (914)

263/16" (665)

84"

(2134)

503/4"

(1289)

23"

(584)

1

(13)

/2"

141/8"

(359)

4" (102)

237/8" (606)

235/8"

(600)

Model BI-30U and BI-30UG.

311/4"

23/8" (60)

(796)

235/8"

(600)

Model BI-36U(ID) and BI-36UG.

371/4"

(946)

23/8" (60)

subzero.com/specs | 7

BUILT-IN REFRIGERATION

Overall Dimensions

OVER-AND-UNDER

HEIGHT DIMENSIONS ±

8"

(203)

36" (914)

263/16" (665)

84"

(2134)

503/4"

(1289)

23"

(584)

1

(13)

/2"

237/8"

(606)

4" (102)

237/8" (606)

HEIGHT DIMENSIONS ±

9"

(229)

42" (1067)

1

/2" (13)

503/4"

(1289)

23"

(584)

237/8"

(606)

84"

(2134)

4" (102)

263/16" (665)

237/8" (606)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

235/8"

191/2"

(600)

(495)

23/8" (60)

Model BI-36UFD(ID).

8 | Sub-Zero Customer Care 800.222.7820

23/8" (60)

Model BI-42UFD(ID).

235/8"

(600)

221/4"

(565)

BUILT-IN REFRIGERATION

Overall Dimensions

SIDE-BY-SIDE

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

HEIGHT DIMENSIONS ±

71/4"

(184)

36" (914)

1

/2" (13)

733/4"

(1873)

83/4"

(222)

84"

(2134)

4" (102)

237/8"

(606)

263/16" (665)

237/8" (606)

HEIGHT DIMENSIONS ±

71/2"

(191)

42" (1067)

1

/2" (13)

733/4"

(1873)

103/8"

(264)

84"

(2134)

4" (102)

237/8"

(606)

263/16" (665)

237/8" (606)

Model BI-36S.

221/4"

(565)

23/8" (60)

Model BI-42S, BI-42SID and BI-42SD.

261/4"

(668)

23/8" (60)

subzero.com/specs | 9

BUILT-IN REFRIGERATION

48" (1219)

84"

(2134)

4"

(102)

733/4"

(1873)

237/8" (606)

237/8"

(606)

30"

(762)

115/8"

(295)

83/8"

(213)

23/8" (60)

HEIGHT DIMENSIONS ±

1

/2" (13)

263/16" (665)

Overall Dimensions

SIDE-BY-SIDE

Model BI-48S, BI-48SID and BI-48SD.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

10 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

Specications

BUILT-IN

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

INTERIOR CAPACITY

ALL REFRIGERATOR / ALL FREEZER R CU FT (L) F CU FT (L)

BI-36R 23.5 (665) BI-36RG 23.4 (663) BI-36F 22.7 (643)

OVER-AND-UNDER R CU FT

(L) F CU FT (L)

BI-30U 13.2 (374) 4.2 (119) BI-30UG 13.1 (371) 4.2 (119) BI-36U(ID) 16.4 (464) 5.3 (150) BI-36UG 16.3 (462) 5.3 (150) BI-36UFD(ID) 15.7 (445) 5.3 (150) BI-42UFD(ID) 18.3 (518) 6.4 (181)

SIDE-BY-SIDE R CU FT

(L) F CU FT (L)

BI-36S 12.4 (351) 8.2 (232) BI-42S 16.3 (462) 8.0 (227) BI-42SID 15.8 (447) 7.9 (224) BI-42SD 16.0 (453) 7.9 (224) BI-48S 19.1 (541) 9.8 (278) BI-48SID 18.6 (527) 9.6 (272) BI-48SD 18.8 (532) 9.6 (272)

SHIPPING WEIGHT

ALL REFRIGERATOR / ALL FREEZER LB (KG)

BI-36R 420 (191) BI-36RG 430 (195) BI-36F 406 (184)

OVER-AND-UNDER LB

BI-30U 462 (210) BI-30UG 476 (216) BI-36U(ID) 515 (234) BI-36UG 529 (240) BI-36UFD(ID) 529 (240) BI-42UFD(ID) 582 (264)

SIDE-BY-SIDE LB

BI-36S 538 (244) BI-42S 582 (264) BI-42SID 608 (276) BI-42SD 608 (276) BI-48S 630 (286) BI-48SID 656 (298) BI-48SD 656 (298)

Shipping weights are based on stainless steel models.

(KG)

subzero.com/specs | 11

BUILT-IN REFRIGERATION

NOTE: Shaded line represents profile of unit.

SIDE

Opening Dimensions

STANDARD INSTALLATION

24" (610)

OPENING

DEPTH

TOP VIEW

W

OPENING WIDTH

FRONT VIEW

VIEW

833/4"

(2127)

OPENING

HEIGHT

OPENING WIDTH

MODEL W

30" Model 291/2" (749) 36" Model 351/2" (902) 42" Model 411/2" (1054) 48" Model 471/2" (1206)

If an 83" (2108) grille height is specied, the opening height

7

must be decreased by specied, the opening height must be increased by 4"

/8" (22). If an 88" (2235) grille height is

(102).

If two units are installed side by side, refer to page 14 for dual standard installations.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

12 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

*3

NOTE: Shaded line represents profile of unit with

SIDE

Opening Dimensions

FLUSH INSET INSTALLATION

263/16"

(665)

FLUSH

INSET

DEPTH

23/16"

(56)

TOP VIEW

FINISHED

CLEATS*

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

1

/4"

(6)

84"

(2134)

FLUSH

INSET

HEIGHT

VIEW

" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.

3/4" (19) panel.

11/4"

(32)

FLUSH INSET WIDTH

FRONT VIEW

W

4" (102)

11/4"

(32)

3"

(76)*

TYPICAL

23/16"

(56)

FLUSH INSET WIDTH

MODEL W

30" Model 32" (813) 36" Model 38" (965) 42" Model 44" (1118) 48" Model 50" (1270)

Dimensions assume a 3/4" (19) panel thickness.

If an 83" height must be decreased by

(2108) grille height is specied, the ush inset

7

/8" (22). If an 88" (2235) grille

height is specied, the ush inset height must be increased

(102).

by 4"

If two units are installed side by side, refer to page 15 for dual ush inset installations.

subzero.com/specs | 13

BUILT-IN REFRIGERATION

NOTE: Shaded line represents profile of unit.

SIDE

Opening Dimensions

DUAL STANDARD INSTALLATION

24" (610)

OPENING

DEPTH

TOP VIEW

VIEW

833/4"

(2127)

OPENING

HEIGHT

OPENING WIDTH

DUAL OPENING WIDTH

MODELS W

Two 30" Models 593/4" (1518) 30" and 36" Models 653/4" (1670) Two 36" Models 713/4" (1822)

W

FRONT VIEW

A dual installation kit will be required for this installation.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

14 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

*3

NOTE: Shaded line represents profile of unit with

SIDE

Opening Dimensions

DUAL FLUSH INSET INSTALLATION

263/16"

(665)

FLUSH

INSET

23/16"

DEPTH

(56)

TOP VIEW

FINISHED

CLEATS*

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

1

/4"

(6)

84"

(2134)

FLUSH

INSET

HEIGHT

VIEW

" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.

3/4" (19) panel.

11/4"

(32)

FLUSH INSET WIDTH

FRONT VIEW

W

11/4"

(32)

4" (102)

3"

(76)*

TYPICAL

23/16"

(56)

DUAL FLUSH INSET WIDTH

MODELS W

Two 30" Models 621/4" (1581) 30" and 36" Models 681/4" (1734) Two 36" Models 741/4" (1886)

Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.

subzero.com/specs | 15

BUILT-IN REFRIGERATION

Electrical

The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

Installation must comply with all applicable electrical codes.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

7"

E

(178)

6"

(152)

751/2" (1918)

FROM FLOOR

RIGHT SIDE

OF OPENING

Plumbing

The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self-piercing valves. The water supply line must not interfere with installation of the anti-tip brackets.

A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi to the unit at all times. A copper line is not recommended for this application.

Installation must comply with all applicable plumbing codes.

PLUMBING REQUIREMENTS

Water Supply

Pressure 35–120 psi

Excess Line for Connection 36" (914)

RIGHT SIDE

OF OPENING

(2.4–8.3 bar) supplied

1

/4" OD copper, braided

stainless steel or PEX tubing

(2.4–8.3 bar)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

Electrical supply location.

16 | Sub-Zero Customer Care 800.222.7820

18" (457)

1

AREA EXTENDS

FORWARD ON FLOOR

/2" (13)

Water supply location.

6" (152)

3" (76)

BUILT-IN REFRIGERATION

Custom Panels

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

For framed, overlay and ush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay and ush inset applications. Refer to panel requirements below and the charts on pages 20–25 for custom panel dimensions for your specic design application.

IMPORTANT NOTE: Do not cover a glass door with a solid

panel.

Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

BI-36R, BI-36RG, BI-36F 75 lb (34 kg) All Other Models 50 lb (23 kg) Grille Panel 13 lb (6 kg)

PANEL THICKNESS MIN

Framed Overlay and Flush Inset

1

/4" (6)

5

/8" (16)

FRAMED PANELS

The framed application is an overlay model with framed design features. It is not a separate model.

1

If the custom panel is thinner than

/4" (6), a ller material

must be added to achieve a proper t. If the panel is thicker

1

/4" (6), rout an edge around the panel or mount the

than custom panel on a sheet of

1

/4" (6) thick material and insert

into the channel. Refer to the illustrations below.

Routing, recessing or optional extended handles may be required for nger clearance. Refer to the full-scale template on page 32.

When installing two units side by side, refer to page 14 for dual standard installations.

1

/4" (6) TRIM REVEAL

1

/4" (6) PANEL

DOOR

1

/4" (6) min

ROUT TO

DOOR

1

/4" (6)

Panel 1/4" thick or less.

Panel thicker than 1/4".

subzero.com/specs | 17

BUILT-IN REFRIGERATION

Custom Panels

PARTIAL FRAMED OPTION

The partial framed kit includes a stainless steel panel for above and below the external dispenser. Refer to the chart below for panel width. The kit is avail able through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

PARTIAL FRAMED PANEL

MODEL WIDTH

BI-42SD 151/16" (383) BI-48SD 183/4" (476)

PANEL MOUNTING KIT

A Sub-Zero custom panel mounting kit eliminates the need for a backer and spacer panel and is avail able through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. The kit consists of mounting cleats, screws and gages used to properly position the cleats. The kit is available for all built-in models except glass door models. Dual installations require two mounting kits.

OVERLAY PANELS

Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10"

(3) spacer panel and a

1

/4" (6) backer

panel. Refer to the illustrations below.

When installing two units side by side, refer to page 14 for dual standard installations.

SPACER PANEL

CUSTOM PANEL

CUSTOM

PANEL

SPACER

PANEL

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

18 | Sub-Zero Customer Care 800.222.7820

BACKER PANEL

TRIM

5

/16" (8) min

1

/8" (3) (OVERLAY)

3

/4"

(19)

typical

.10" (3)

1

/4" (6)

BACKER

PANEL

Panel assembly (cross section). Panel assembly (rear view).

BUILT-IN REFRIGERATION

65/16" (160)

3

/32"

(2)

1

/8" (3)

RADIUS

5

/8"

(16)

127/8"

(327)

Custom Panels

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

FLUSH INSET PANELS

The ush inset application is an overlay model with ush inset panels. It is not a separate model.

The ush inset design allows custom panels to be installed ush with adjacent cabinets. Similar to overlay, ush inset

3

panels are typically created by combining a panel, a .10"

(3) spacer panel and a

1

/4" (6) backer panel.

/4" (19) custom

Refer to the illustrations for overlay panels.

3

For ush inset panels thicker than

/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale templates at the end of this guide.

When installing two units side by side, refer to page 15 for dual ush inset installations.

ICE AND WATER DISPENSER

For models BI-42SD and BI-48SD, the refrigerator door panel must include a cut-out to accommodate the external dispenser. The thickness of the panel in this area can range

1

/4" (6) to a maximum of 11/8" (29). Refer to the illustra-

from tions below.

2"

(25)

(51)

1"

HANDLE

GLASSWELL

Dispenser dimensions.

Handle placement.

subzero.com/specs | 19

BUILT-IN REFRIGERATION

H

W

AA

A

H

W

AA

A

B

H

W

H

W

W W

H

W

AA

A

H

W

W W

H

W

AA

A

H

W

H

W

W W

H

W

W W

Framed Panel Dimensions

W

BI-36R, BI-36F

H

A

H

B

W

BI-36RG

H

AA

BI-30U, BI-36U(ID)

MODEL BI-36R, BI-36RG, BI-36F

REFRIGERATOR/FREEZER W H

Door Panel 353/4" (908) 699/16" (1767)

GRILLE (OPTIONAL) W H

Grille Panel 353/4" (908) 815/16" (227)

BI-36RG A B

Stiles / Rails 53/16" (132) 105/16" (262)

MODEL BI-30U, BI-30UG

REFRIGERATOR W H

Door Panel 293/4" (756) 4915/16" (1268)

FREEZER W H

Drawer Panel 293/4" (756) 1811/16" (475)

GRILLE (OPTIONAL) W H

Grille Panel 293/4" (756) 815/16" (227)

BI-30UG A

Stiles / Rails 53/16" (132)

H

A

H

A

H

W

BI-30UG, BI-36UG

H

AA

H

BI-36UFD(ID), BI-42UFD(ID)

MODEL BI-36U(ID), BI-36UG

REFRIGERATOR W H

Door Panel 353/4" (908) 4915/16" (1268)

FREEZER W H

Drawer Panel 353/4" (908) 1811/16" (475)

GRILLE (OPTIONAL) W H

Grille Panel 353/4" (908) 815/16" (227)

BI-36UG A

Stiles / Rails 53/16" (132)

MODEL BI-36UFD(ID)

REFRIGERATOR (2 PANELS) W H

Door Panels 175/8" (448) 4915/16" (1268)

FREEZER W H

Drawer Panel 353/4" (908) 1811/16" (475)

GRILLE (OPTIONAL) W H

Grille Panel 353/4" (908) 815/16" (227)

H

W W

H

W

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

20 | Sub-Zero Customer Care 800.222.7820

MODEL BI-42UFD(ID)

REFRIGERATOR (2 PANELS) W H

Door Panels 205/8" (524) 4915/16" (1268)

FREEZER W H

Drawer Panel 413/4" (1060) 1811/16" (475)

GRILLE (OPTIONAL) W H

Grille Panel 413/4" (1060) 815/16" (227)

BUILT-IN REFRIGERATION

H

W

AA

A

H

W

H

W

AA

A

B

H

W

H

WW

B

A

H

W

W W

H

W

AA

A

H

W

AA

A

B

H

W

H

W

W W

Framed Panel Dimensions

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

H

A

B

W

BI-36S, BI-42S, BI-42SID,

W

WW

BI-42SD, BI-48SD

BI-48S, BI-48SID

MODEL BI-36S

REFRIGERATOR W H

Door Panel 1913/16" (503) 699/16" (1767)

FREEZER W H

Door Panel 157/16" (392) 699/16" (1767)

GRILLE (OPTIONAL) W H

Grille Panel 353/4" (908) 815/16" (227)

MODEL BI-42S, BI-42SID, BI-42SD

REFRIGERATOR W H

Door Panel 2413/16" (630) 699/16" (1767)

FREEZER W H

Door Panel 167/16" (418) 699/16" (1767)

GRILLE (OPTIONAL) W H

Grille Panel 413/4" (1060) 815/16" (227)

BI-42SD W H

Dispenser Cut-Out* 57/8" (149) 127/16" (316)

A B

Cut-Out Location 17/8" (48) 283/4" (730)

H

MODEL BI-48S, BI-48SID, BI-48SD

REFRIGERATOR W H

Door Panel 281/2" (724) 699/16" (1767)

FREEZER W H

Door Panel 183/4" (476) 699/16" (1767)

GRILLE (OPTIONAL) W H

Grille Panel 473/4" (1213) 815/16" (227)

BI-48SD W H

Dispenser Cut-Out* 57/8" (149) 127/16" (316)

*For models BI-42SD and BI-48SD, panel thickness in the dispenser area can range from 1/4" (6) to a maximum of 11/8" (29). If the panel

Cut-Out Location 17/8" (48) 283/4" (730)

A B

is thicker, you must rout out a minimum 1/4" (6) at landing area to accommodate the dispenser.

subzero.com/specs | 21

BUILT-IN REFRIGERATION

H

W

AA

A

H

W

AA

A

B

H

W

H

W

W W

H

W

AA

A

H

W

W W

H

W

AA

A

H

W

H

W

W W

H

W

W W

Overlay Panel Dimensions

W

BI-36R, BI-36F

H

A

H

B

W

BI-36RG

H

AA

BI-30U, BI-36U(ID)

MODEL BI-36R, BI-36RG, BI-36F

REFRIGERATOR / FREEZER W H

Overlay Panel 36" (914) 693/4" (1772) Spacer Panel 351/8" (892) 6815/16" (1751) Backer Panel 353/4" (908) 699/16" (1767)

GRILLE W H

Overlay Panel 36" (914) 91/4" (235)*

1

Spacer Panel 35

/8" (892) 85/16" (211)

Backer Panel 353/4" (908) 815/16" (227)

BI-36RG A B

Stiles / Rails 51/4" (133) 103/8" (264)

MODEL BI-30U, BI-30UG

REFRIGERATOR W H

Overlay Panel 30" (762) 501/8" (1273) Spacer Panel 291/8" (740) 495/16" (1253) Backer Panel 293/4" (756) 4915/16" (1268)

FREEZER W H

Overlay Panel 30" (762) 19" (483) Spacer Panel 291/8" (740) 181/16" (459) Backer Panel 293/4" (756) 1811/16" (475)

GRILLE W H

Overlay Panel 30" (762) 91/4" (235)* Spacer Panel 29 Backer Panel 293/4" (756) 815/16" (227)

1

/8" (740) 85/16" (211)

BI-30UG A

Stiles / Rails 51/4" (133)

H

A

H

A

H

W

BI-30UG, BI-36UG

H

AA

H

BI-36UFD(ID), BI-42UFD(ID)

MODEL BI-36U(ID), BI-36UG

REFRIGERATOR W H

Overlay Panel 36" (914) 501/8" (1273) Spacer Panel 351/8" (892) 495/16" (1253) Backer Panel 353/4" (908) 4915/16" (1268)

FREEZER W H

Overlay Panel 36" (914) 19" (483) Spacer Panel 351/8" (892) 181/16" (459) Backer Panel 353/4" (908) 1811/16" (475)

GRILLE W H

Overlay Panel 36" (914) 91/4" (235)*

1

Spacer Panel 35

/8" (892) 85/16" (211)

Backer Panel 353/4" (908) 815/16" (227)

BI-36UG A

Stiles / Rails 51/4" (133)

MODEL BI-36UFD(ID)

REFRIGERATOR (2 PANELS) W H

Overlay Panels 177/8" (454) 501/8" (1273) Spacer Panels 17" (432) 495/16" (1253) Backer Panels 175/8" (448) 4915/16" (1268)

FREEZER W H

Overlay Panel 36" (914) 19" (483) Spacer Panel 351/8" (892) 181/16" (459) Backer Panel 353/4" (908) 1811/16" (475)

GRILLE W H

Overlay Panel 36" (914) 91/4" (235)* Spacer Panel 351/8" (892) 85/16" (211) Backer Panel 353/4" (908) 815/16" (227)

H

W W

H

W

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

22 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

H

W

AA

A

H

W

H

W

AA

A

B

H

W

H

WW

B

A

H

W

W W

H

W

AA

A

H

W

AA

A

B

H

W

H

W

W W

Overlay Panel Dimensions

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

H

A

B

W

BI-36S, BI-42S, BI-42SID,

W

WW

BI-42SD, BI-48SD

BI-48S, BI-48SID

MODEL BI-42UFD(ID)

REFRIGERATOR (2 PANELS) W H

Overlay Panels 207/8" (530) 501/8" (1273) Spacer Panels 20" (508) 495/16" (1253) Backer Panels 205/8" (524) 4915/16" (1268)

FREEZER W H

Overlay Panel 42" (1067) 19" (483) Spacer Panel 411/8" (1045) 181/16" (459) Backer Panel 413/4" (1060) 1811/16" (475)

GRILLE W H

Overlay Panel 42" (1067) 91/4" (235)* Spacer Panel 41

1

/8" (1045) 85/16" (211)

Backer Panel 413/4" (1060) 815/16" (227)

MODEL BI-36S

REFRIGERATOR W H

Overlay Panel 201/16" (510) 693/4" (1772) Spacer Panel 193/16" (487) 6815/16" (1751) Backer Panel 1913/16" (503) 699/16" (1767)

FREEZER W H

Overlay Panel 1511/16" (398) 693/4" (1772) Spacer Panel 1413/16" (376) 6815/16" (1751) Backer Panel 157/16" (392) 699/16" (1767)

GRILLE W H

Overlay Panel 36" (914) 91/4" (235)*

1

Spacer Panel 35

/8" (892) 85/16" (211)

Backer Panel 353/4" (908) 815/16" (227)

H

MODEL BI-42S, BI-42SID, BI-42SD

REFRIGERATOR W H

Overlay Panel 251/16" (637) 693/4" (1772) Spacer Panel 243/16" (614) 6815/16" (1751) Backer Panel 2413/16" (630) 699/16" (1767)

H

FREEZER W H

Overlay Panel 1611/16" (424) 693/4" (1772) Spacer Panel 1513/16" (402) 6815/16" (1751) Backer Panel 167/16" (418) 699/16" (1767)

GRILLE W H

Overlay Panel 42" (1067) 91/4" (235)*

1

Spacer Panel 41

/8" (1045) 85/16" (211)

Backer Panel 413/4" (1060) 815/16" (227)

BI-42SD W H

Dispenser Cut-Out 57/8" (149) 127/16" (316)

A B

Cut-Out Location 2" (51) 2813/16" (732)

MODEL BI-48S, BI-48SID, BI-48SD

REFRIGERATOR W H

Overlay Panel 283/4" (730) 693/4" (1772) Spacer Panel 277/8" (708) 6815/16" (1751) Backer Panel 281/2" (724) 699/16" (1767)

FREEZER W H

Overlay Panel 19" (483) 693/4" (1772) Spacer Panel 181/8" (460) 6815/16" (1751) Backer Panel 183/4" (476) 699/16" (1767)

GRILLE W H

Overlay Panel 48" (1219) 91/4" (235)* Spacer Panel 47

1

/8" (1197) 85/16" (211)

Backer Panel 473/4" (1213) 815/16" (227)

BI-48SD W H

Dispenser Cut-Out 57/8" (149) 127/16" (316)

Cut-Out Location 2" (51) 2813/16" (732)

*Panel height may be increased by 7/16" (11) to hide upper main

A B

frame. For more information, refer to the built-in panel congurator at subzero.com/trade/panels.

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specic panel grille must be ordered for an 83" or 88" overall unit height.

subzero.com/specs | 23

BUILT-IN REFRIGERATION

H

W

AA

B

H

W

AA

A

B

H

W

H

W

W W

H

W

AA

B

H

W

W W

H

W

AA

A

H

W

H

W

W W

H

W

W W

Flush Inset Panel Dimensions

H

AA

BI-30U, BI-36U(ID)

W

BI-36R, BI-36F

H

A

H

B

W

BI-36RG

MODEL BI-36R, BI-36RG, BI-36F

REFRIGERATOR / FREEZER W H

Flush Inset Panel 37" (940) 693/4" (1772) Spacer Panel 351/8" (892) 6815/16" (1751) Backer Panel 353/4" (908) 699/16" (1767)

GRILLE W H

Flush Inset Panel 37" (940) 91/4" (235) Spacer Panel 351/8" (892) 85/16" (211) Backer Panel 353/4" (908) 815/16" (227)

BI-36RG A B

Stiles / Rails 53/4" (146) 103/8" (264)

MODEL BI-30U, BI-30UG

REFRIGERATOR W H

Flush Inset Panel 31" (787) 501/8" (1273) Spacer Panel 291/8" (740) 495/16" (1253) Backer Panel 293/4" (756) 4915/16" (1268)

FREEZER W H

Flush Inset Panel 31" (787) 19" (483) Spacer Panel 291/8" (740) 181/16" (459) Backer Panel 293/4" (756) 1811/16" (475)

GRILLE W H

Flush Inset Panel 31" (787) 91/4" (235) Spacer Panel 291/8" (740) 85/16" (211) Backer Panel 293/4" (756) 815/16" (227)

BI-30UG A B

Stiles / Rails 53/4" (146) 51/4" (133)

H

B

H

B

H

W

BI-30UG, BI-36UG

H

AA

H

BI-36UFD(ID), BI-42UFD(ID)

MODEL BI-36U(ID), BI-36UG

REFRIGERATOR W H

Flush Inset Panel 37" (940) 501/8" (1273) Spacer Panel 351/8" (892) 495/16" (1253) Backer Panel 353/4" (908) 4915/16" (1268)

FREEZER W H

Flush Inset Panel 37" (940) 19" (483) Spacer Panel 351/8" (892) 181/16" (459) Backer Panel 353/4" (908) 1811/16" (475)

GRILLE W H

Flush Inset Panel 37" (940) 91/4" (235) Spacer Panel 351/8" (892) 85/16" (211) Backer Panel 353/4" (908) 815/16" (227)

BI-36UG A B

Stiles / Rails 53/4" (146) 51/4" (133)

MODEL BI-36UFD(ID)

REFRIGERATOR (2 PANELS) W H

Flush Inset Panels 183/8" (467) 501/8" (1273) Spacer Panels 17" (432) 495/16" (1253) Backer Panels 175/8" (448) 4915/16" (1268)

FREEZER W H

Flush Inset Panel 37" (940) 19" (483) Spacer Panel 351/8" (892) 181/16" (459) Backer Panel 353/4" (908) 1811/16" (475)

GRILLE W H

Flush Inset Panel 37" (940) 91/4" (235) Spacer Panel 351/8" (892) 85/16" (211) Backer Panel 353/4" (908) 815/16" (227)

H

W W

H

W

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

24 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

H

W

AA

A

H

W

H

W

AA

A

B

H

W

H

WW

B

A

H

W

W W

H

W

AA

A

H

W

AA

A

B

H

W

H

W

W W

Flush Inset Panel Dimensions

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

H

A

B

W

BI-36S, BI-42S, BI-42SID,

W

WW

BI-42SD, BI-48SD

BI-48S, BI-48SID

MODEL BI-42UFD(ID)

REFRIGERATOR (2 PANELS) W H

Flush Inset Panels 213/8" (543) 501/8" (1273) Spacer Panels 20" (508) 495/16" (1253) Backer Panels 205/8" (524) 4915/16" (1268)

FREEZER W H

Flush Inset Panel 43" (1092) 19" (483) Spacer Panel 411/8" (1045) 181/16" (459) Backer Panel 413/4" (1060) 1811/16" (475)

GRILLE W H

Flush Inset Panel 43" (1092) 91/4" (235) Spacer Panel 411/8" (1045) 85/16" (211) Backer Panel 413/4" (1060) 815/16" (227)

MODEL BI-36S

REFRIGERATOR W H

Flush Inset Panel 209/16" (522) 693/4" (1772) Spacer Panel 193/16" (487) 6815/16" (1751) Backer Panel 1913/16" (503) 699/16" (1767)

FREEZER W H

Flush Inset Panel 163/16" (411) 693/4" (1772) Spacer Panel 1413/16" (376) 6815/16" (1751) Backer Panel 157/16" (392) 699/16" (1767)

GRILLE W H

Flush Inset Panel 37" (940) 91/4" (235) Spacer Panel 351/8" (892) 85/16" (211) Backer Panel 353/4" (908) 815/16" (227)

H

MODEL BI-42S, BI-42SID, BI-42SD

REFRIGERATOR W H

Flush Inset Panel 259/16" (649) 693/4" (1772) Spacer Panel 243/16" (614) 6815/16" (1751) Backer Panel 2413/16" (630) 699/16" (1767)

H

FREEZER W H

Flush Inset Panel 173/16" (437) 693/4" (1772) Spacer Panel 1513/16" (402) 6815/16" (1751) Backer Panel 167/16" (418) 699/16" (1767)

GRILLE W H

Flush Inset Panel 43" (1092) 91/4" (235) Spacer Panel 411/8" (1045) 85/16" (211) Backer Panel 413/4" (1060) 815/16" (227)

DISPENSER (BI-42SD) W H

Dispenser Cut-Out 57/8" (149) 127/16" (316)

A B

Cut-Out Location 2" (51) 2813/16" (732)

MODEL BI-48S, BI-48SID, BI-48SD

REFRIGERATOR W H

Flush Inset Panel 291/4" (743) 693/4" (1772) Spacer Panel 277/8" (708) 6815/16" (1751) Backer Panel 281/2" (724) 699/16" (1767)

FREEZER W H

Flush Inset Panel 191/2" (495) 693/4" (1772) Spacer Panel 181/8" (460) 6815/16" (1751) Backer Panel 183/4" (476) 699/16" (1767)

GRILLE W H

Flush Inset Panel 49" (1245) 91/4" (235) Spacer Panel 471/8" (1197) 85/16" (211) Backer Panel 473/4" (1213) 815/16" (227)

DISPENSER (BI-48SD) W H

Cut-Out 57/8" (149) 127/16" (316)

Cut-Out Location 2" (51) 2813/16" (732)

Grille panel dimensions are for standard 84" (2134) overall unit

A B

height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specic panel grille must be ordered for an 83" or 88" overall unit height.

subzero.com/specs | 25

BUILT-IN REFRIGERATION

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEW

5

/8"

(16)

5

/16"

(8)

1

/2"

(13)

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

FLUSH INSET PANEL

SPACER

BACKER

DOOR DOOR

DOOR / DRAWER / GRILLE

TOP VIEWTOP VIEW

SIDE VIEW

CABINETRY

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

5

/8"

(16)

5

/16" (8)

1

/2"

(13)

5

/16"

(8)

3

/32"

(2)

DOOR /

DRAWER

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

FLUSH INSET PANEL

SPACER

BACKER

DOOR DOOR

DOOR / DRAWER / GRILLE

1

/2"(13)

5

/16"

(8)

1

/8"

(3)

CABINETRY

GRILLE

TOP VIEWTOP VIEW

SIDE VIEW SIDE VIEW

SIDE VIEW

CABINETRY

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

Flush Inset Panels

PANEL OFFSET

The illustrations provide panel offsets and reveals for built-in models in a ush inset application. Refer to the chart below for reference to the illustrations.

PANEL OFFSET

ALL REFRIGERATOR / ALL FREEZER ILLUS

Door / Grille Sides A Grille Top C Grille Bottom / Door Top D Door Bottom F

OVER-AND-UNDER ILLUS

Door (hinge) / Drawer / Grille Sides A Doors (handle) Sides (French door only) B Grille Top C Grille Bottom / Door Top D Door Bottom / Drawer Top E Drawer Bottom F

SIDE-BY-SIDE ILLUS

Doors (hinge) / Grille Sides A Doors (handle) Sides B Grille Top C Grille Bottom / Door Top D Door Bottom F

5

/16"

TOP VIEW

(8)

DOOR / DRAWER / GRILLE

BACKER

SPACER

FLUSH INSET PANEL

Illus. A

CABINETRY

GRILLE

Illus. C

DOOR

DRAWER

CABINETRY

5

/8"

(16)

5

/16"

(8)

SIDE VIEW

5

/16"

(8)

5

/16"

(8)

SIDE VIEW

TOP VIEW

DOOR DOOR

5

1

/2"

(13)

1

/2"(13)

1

/8"

(3)

3

/32"

(2)

5

/8"(16)

5

/32"

(4)

/16" (8)

1

Illus. B

DOOR

Illus. D

/8" (3)

GRILLE

DOOR /

DRAWER

SIDE VIEW

1

/4" (6)

REVEAL

5

/16"

(8)

5

/16"

(8)

SIDE VIEW

5

3

/16"

(8)

/32"

(4)

/32"

(2)

1

/2"(13)

3

/32"

(2)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

26 | Sub-Zero Customer Care 800.222.7820

Illus. E

Illus. F

BUILT-IN REFRIGERATION

Dual Installation

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

If two units are installed side by side, a dual installation kit may be required. Installations without a custom ller strip require a dual installation kit. If a dual installation kit is not specied, a 2"

(51) ller strip is recommended between units.

A custom ller strip is required when installing two French door or side-by-side models. Dual installations without a ller strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

For dual standard installations, panel dimensions are the same as for single installations. Refer to the charts on pages 20–23. Panel dimensions and offsets for dual ush inset installations are listed on the following pages.

WITHOUT FILLER STRIP

Opposite hinges.

FILLER STRIP

Same side hinges.

subzero.com/specs | 27

BUILT-IN REFRIGERATION

H

W

AA

B

H

W

AA

A

B

H

W

H

W

W W

H

W

AA

B

H

W

W W

H

W

AA

A

H

W

H

W

W W

H

W

W W

Dual Flush Inset Panel Dimensions

H

AA

W

BI-36R, BI-36F

H

A

H

B

W

BI-36RG

MODEL BI-36R, BI-36RG, BI-36F

REFRIGERATOR / FREEZER W H

Flush Inset Panel 361/2" (927) 693/4" (1772) Spacer Panel 351/8" (892) 6815/16" (1751) Backer Panel 353/4" (908) 699/16" (1767)

GRILLE W H

Flush Inset Panel 361/2" (927) 91/4" (235) Spacer Panel 351/8" (892) 85/16" (211) Backer Panel 353/4" (908) 815/16" (227)

BI-36RG A B

Stiles / Rails 53/4" (146) 103/8" (264)

MODEL BI-30U, BI-30UG

REFRIGERATOR W H

Flush Inset Panel 301/2" (775) 501/8" (1273) Spacer Panel 291/8" (740) 495/16" (1253) Backer Panel 293/4" (756) 4915/16" (1268)

FREEZER W H

Flush Inset Panel 301/2" (775) 19" (483) Spacer Panel 291/8" (740) 181/16" (459) Backer Panel 293/4" (756) 1811/16" (475)

GRILLE W H

Flush Inset Panel 301/2" (775) 91/4" (235) Spacer Panel 291/8" (740) 85/16" (211) Backer Panel 293/4" (756) 815/16" (227)

BI-30UG A B

Stiles / Rails 53/4" (146) 51/4" (133)

W

BI-30U, BI-36U(ID)

H

B

H

B

H

W

BI-30UG, BI-36UG

H

AA

H

MODEL BI-36U(ID), BI-36UG

REFRIGERATOR W H

Flush Inset Panel 361/2" (927) 501/8" (1273) Spacer Panel 351/8" (892) 495/16" (1253) Backer Panel 353/4" (908) 4915/16" (1268)

FREEZER W H

Flush Inset Panel 361/2" (927) 19" (483) Spacer Panel 351/8" (892) 181/16" (459) Backer Panel 353/4" (908) 1811/16" (475)

GRILLE W H

Flush Inset Panel 361/2" (927) 91/4" (235) Spacer Panel 351/8" (892) 85/16" (211) Backer Panel 353/4" (908) 815/16" (227)

BI-36UG A B

Stiles / Rails 53/4" (146) 51/4" (133)

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specic panel grille must be ordered for an 83" or 88" overall unit height. For dual wide grilles, refer to page 30.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

28 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEW

5

/8"

(16)

5

/16"

(8)

1

/2"

(13)

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

FLUSH INSET PANEL

SPACER

BACKER

DOOR DOOR

DOOR / DRAWER / GRILLE

TOP VIEWTOP VIEW

SIDE VIEW

CABINETRY

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

5

/8"

(16)

5

/16" (8)

1

/2"

(13)

5

/16"

(8)

3

/32"

(2)

DOOR /

DRAWER

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

FLUSH INSET PANEL

SPACER

BACKER

DOOR DOOR

DOOR / DRAWER / GRILLE

1

/2"(13)

5

/16"

(8)

1

/8"

(3)

CABINETRY

GRILLE

TOP VIEWTOP VIEW

SIDE VIEW SIDE VIEW

SIDE VIEW

CABINETRY

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

Dual Installation

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

DUAL FLUSH INSET PANEL OFFSET

The illustrations provide panel offsets and reveals for built-in models in a dual ush inset application. Refer to the chart below for reference to the illustrations.

PANEL OFFSET

ALL REFRIGERATOR / ALL FREEZER ILLUS

Door (hinge) / Grille Sides A Door (handle) Sides B Grille Top C Grille Bottom / Door Top D Door Bottom F

OVER-AND-UNDER ILLUS

Door (hinge) / Drawer / Grille Sides A Door (handle) Sides B Grille Top C Grille Bottom / Door Top D Door Bottom / Drawer Top E Drawer Bottom F

5

/16"

TOP VIEW

(8)

DOOR / DRAWER / GRILLE

BACKER

SPACER

FLUSH INSET PANEL

Illus. A

CABINETRY

GRILLE

Illus. C

DOOR

DRAWER

CABINETRY

5

/8"

(16)

5

/16"

(8)

SIDE VIEW

5

/16"

(8)

5

/16"

(8)

SIDE VIEW

TOP VIEW

DUAL TRIM

DOOR DOOR

5

1

/2"

(13)

1

/2"(13)

1

/8"

(3)

3

/32"

(2)

5

/8"(16)

5

/32"

(4)

/16" (8)

Illus. B

DOOR

Illus. D

1

/8" (3)

GRILLE

DOOR /

DRAWER

SIDE VIEW

1

/4" (6)

REVEAL

5

/16"

(8)

5

/16"

(8)

SIDE VIEW

5

3

/16"

(8)

/32"

(4)

/32"

(2)

1

/2"(13)

3

/32"

(2)

Illus. E

Illus. F

subzero.com/specs | 29

BUILT-IN REFRIGERATION

Dual Installation

DUAL WIDE GRILLE

A dual wide grille spans the entire width of both units in a dual installation and is a part of a dual installation kit.

For overlay and ush inset panel dimensions for the dual wide grille, refer to the charts below. Dimensions listed are for a standard 84"

DUAL WIDE GRILLE—OVERLAY

TWO 30" MODELS W H

Overlay Panel 601/4" (1530) 91/4" (235) Spacer Panel 593/8" (1508) 85/16" (211) Backer Panel 60" (1524) 815/16" (227)

30" AND 36" MODEL W H

Overlay Panel 661/4" (1683) 91/4" (235) Spacer Panel 653/8" (1661) 85/16" (211) Backer Panel 66" (1676) 815/16" (227)

TWO 36" MODELS W H

Overlay Panel 721/4" (1835) 91/4" (235) Spacer Panel 713/8" (1813) 85/16" (211) Backer Panel 72" (1829) 815/16" (227)

(2134) nished height.

DUAL WIDE GRILLE—FLUSH INSET

TWO 30" MODELS W H

Flush Inset Panel 611/4" (1556) 91/4" (235) Spacer Panel 593/8" (1508) 85/16" (211) Backer Panel 60" (1524) 815/16" (227)

30" AND 36" MODEL W H

Flush Inset Panel 671/4" (1708) 91/4" (235) Spacer Panel 653/8" (1661) 85/16" (211) Backer Panel 66" (1676) 815/16" (227)

TWO 36" MODELS W H

Flush Inset Panel 731/4" (1861) 91/4" (235) Spacer Panel 713/8" (1813) 85/16" (211) Backer Panel 72" (1829) 815/16" (227)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

30 | Sub-Zero Customer Care 800.222.7820

84"

(2134)

24"

(610)

ROUT TO

3

/16" (5)

(OVER-AND-UNDER

MODELS)

OPTIONAL

TOE KICK CUT-OUT

4" (102)

201/2"

(521)

53/4"

(146)

17/8"(48)

1" (25)

41/4" (108)

ROUT TO

1

/8"

(3)

FRONT

OF SIDE

PANEL

25/8"

(67)

MAIN

FRAME

SIDE PANEL

ROUTING

1" (25)

17/8" (48)

1

/8" (3)

1

/2" (13)

BUILT-IN REFRIGERATION

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Side Panel

The custom side panels must be a minimum of 24" (610) deep and side panel to t ush against the side of the unit. Refer to the illustrations below.

When installing a built-in unit with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

1

/2" (13) thick. Routing will be necessary for the

Standard Handles

Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

Refer to the chart below for standard handle lengths for built-in models.

HANDLE LENGTH

BUILT-IN TUBULAR PRO

Full Door 637/8" (1622) 453/16" (1147) Over-and-Under Door 441/4" (1124) 371/2" (952) 30" Drawer 245/16" (633) 179/16" (447) 36" Drawer 305/16" (770) 235/8" (600) 42" Drawer 365/16" (922) 295/8" (753)

Side panel dimensions.

Routing detail.

subzero.com/specs | 31

BUILT-IN REFRIGERATION

Framed Panels

FULL-SCALE TEMPLATE

OPTIONAL EXTENDED FULL-LENGTH HANDLE

1"

(25)

1

/4" (6) FRAMED PANEL

STANDARD FULL-LENGTH HANDLE

2"

(51)

DOOR

3"

(76)

11/4" (32) PANEL

1" (25) PANEL

3

/4" (19) PANEL

1

/2" (13) PANEL

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

Framed panel thickness.

32 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

Overlay and Flush Inset Panels

FULL-SCALE TEMPLATE

Overlay and ush inset panels must be a minimum of 5/8"

(16)

thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door.

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

1"

(25)

1

/4" (6) BACKER PANEL

DOOR

DEPTH OF TUBULAR AND PRO HANDLES

2"

(51)

3"

(76)

11/4" (32) PANEL

1" (25) PANEL

3

/4" (19) PANEL

.10" (3) SPACER PANEL

Overlay and ush inset panel thickness.

subzero.com/specs | 33

BUILT-IN REFRIGERATION

237/8"

(606)

TO REAR OF UNIT

OVERALL WIDTH OF UNIT

1

/

4

"

(32)

1

/

2

"

(38)

1

3

/

4

"

(44)

0"

(0)

1"

(25)

2"

(51)

2

1

/

4

"

(57)

2

1

/

2

"

(63)

2

3

/

4

"

(70)

3"

(76)

3

1

/

4

"

(83)

3

1

/

2

"

(89)

1

/

4

"

(6)

1

/

2

"

(13)

3

/

4

"

(19)

3

/4"

(19) THICK

OVERLAY PANEL

(TYPICAL)

1

/4"

(6) BACKER

PANEL

1"

(25) THICK

PANEL

Overlay Application

FULL-SCALE TEMPLATE

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

90° door opening (top view).

34 | Sub-Zero Customer Care 800.222.7820

1" (25)0"

SCALE

BUILT-IN REFRIGERATION

Flush Inset Application

24"

(610)

FULL-SCALE TEMPLATE

For panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets.

TO BACK WALL

23/16"

(56)

ASSUMES

3

/4" (19)

FLUSH INSET

PANEL

THICKNESS

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

11/4" (32)

1" (25) THICK

PANEL

3

/4" (19) THICK

FLUSH INSET PANEL

(TYPICAL)

1

/4" (6) BACKER

PANEL

110° door opening (top view).

1" (25)0"

SCALE

subzero.com/specs | 35

BUILT-IN REFRIGERATION

FILLER STRIP

11/4" (32)

APPROX PROFILE OF

STAINLESS STEEL WRAPPED

DOOR AND HANDLE

Dual Standard Installation

FULL-SCALE TEMPLATE

Typical framed, overlay or stainless steel dual installation with ller strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

DOOR

CLOSED

DOOR

OPEN 110°

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

1" (25)0"

SCALE

Dual standard installation (top view).

36 | Sub-Zero Customer Care 800.222.7820

BUILT-IN REFRIGERATION

FILLER STRIP

11/2" (38)

1

/2" (13)

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

PROFILE OF

3

(19) FLUSH INSET PANEL

/4"

AND TUBULAR HANDLE

Dual Flush Inset Installation

FULL-SCALE TEMPLATE

Typical ush inset dual installation with ller strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

DOOR

CLOSED

DOOR

OPEN 110°

1" (25)0"

SCALE

Dual ush inset installation (top view).

subzero.com/specs | 37

PRO 48 REFRIGERATION

PRO 48 Refrigeration

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Freshness nds unmistakable expression in the Sub-Zero PRO 48. An 800-pound monument to food preservation— equal parts sculpted metal design statement and culinary secret weapon. Its vast interior, like its bold exterior, is crafted of stainless steel. The PRO 48 is available with or without a glass door and may be either built in or freestanding.

PRO 48 MODELS

648PRO

648PROG

KEY FEATURES

• Can be used freestanding or installed as a standard or

ush built-in application.

• Stainless steel interior as well as exterior.

• Handles coordinate with handles of Wolf ranges.

• Dual refrigeration system enhanced with triple evapora-

tors allow independent control of storage conditions in refrigerator cabinet and drawer compartments.

• Advanced water ltration system.

• Slide-out stainless steel bins t neatly under refrigerator

glass shelves.

• Exterior temperature display.

• Flip-up grille provides easy access for quick routine

maintenance.

• Star-K certied.

subzero.com/specs | 39

PRO 48 REFRIGERATION

Overall Dimensions

PRO 48

141/2"

(368)

48" (1219)

HEIGHT DIMENSIONS ±

1

/2" (13)

421/8"

(1070)

301/2"

(775)

21"

(533)

84"

(2134)

4" (102)

237/8"

(606)

257/8" (657)

303/16"

(767)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

Model 648PRO and 648PROG.

40 | Sub-Zero Customer Care 800.222.7820

23/8" (60)

303/4"

(781)

SPECIFICATIONS

INTERIOR CAPACITY R CU FT (L) F CU FT (L)

648PRO, 648PROG 18.4 (521) 11.7 (331)

SHIPPING WEIGHT LB

(KG)

648PRO 860 (390) 648PROG 875 (397)

PRO 48 REFRIGERATION

SIDE

Opening Dimensions

STANDARD AND FLUSH INSTALLATION

TOP VIEW

D

OPENING

DEPTH

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

W

OPENING WIDTH

FRONT VIEW

VIEW

H

OPENING

HEIGHT

OPENING DIMENSIONS

INSTALLATION W H D

Standard 471/2" (1206) 833/4" (2127) 24" (610) Flush 48" (1219) 841/8" (2137) 26" (660)

For standard built-in installations, the face frame of the unit will extend 2"

(51) beyond cabinetry. For ush installations,

the front of the face frame will be ush with surrounding cabinetry.

subzero.com/specs | 41

PRO 48 REFRIGERATION

Electrical

The electrical supply should be located within the shaded area shown in the illustration below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

Installation must comply with all applicable electrical codes.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

7"

E

(178)

6"

(152)

751/2" (1918)

FROM FLOOR

RIGHT SIDE

OF OPENING

Plumbing

The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self-piercing valves. The water supply line must not interfere with installation of the anti-tip bracket.

A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi to the unit at all times. A copper line is not recommended for this application.

Installation must comply with all applicable plumbing codes.

PLUMBING REQUIREMENTS

Water Supply

Pressure 35–120 psi

Excess Line for Connection 36" (914)

RIGHT SIDE

OF OPENING

(2.4–8.3 bar) supplied

1

/4" OD copper, braided

stainless steel or PEX tubing

(2.4–8.3 bar)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

Electrical supply location.

42 | Sub-Zero Customer Care 800.222.7820

6"

(152)

3" (76)

AREA EXTENDS

FORWARD ON FLOOR

Water supply location.

53/16"

(132)

1

/2" (13)

PRO 48 REFRIGERATION

Standard Handles

Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

Refer to the chart below for standard handle lengths for PRO 48 models.

HANDLE LENGTH

PRO 48 TUBULAR PRO

Door NA 2711/16" (703) Refrigerator Drawer NA 1915/16" (506) Freezer Drawer NA 119/16" (294)

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

subzero.com/specs | 43

INTEGRATED REFRIGERATION

Integrated Refrigeration

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

With custom front panels and hardware, Sub-Zero invented integrated columns, tall and drawer models that disappear into the decor. Integrated units t ush with other cabinets, making integrated refrigeration as practical and beautiful in the master suite, bar or theatre room as in the kitchen.

INTEGRATED MODELS

KEY FEATURES

• Custom front panels and hardware allow for innite

design options.

• Point-of-use refrigeration that can be placed anywhere in

the home.

• Dual refrigeration; two compressors preserve food’s

goodness in self-contained compartments.

®

• Energy efcient; many models are ENERGY STAR

qualied.

• Star-K certied.

IC-18FI

ID-24R,

ID-24F(I)

IC-24R, IC-24FI

ID-27R

IC-30R(ID),

IC-30FI

ID-30F(I), ID-30C(I)

ID-30R(P),

IC-36R(ID)

ID-36R(P),

ID-36C(I)

IT-30R(ID),

IT-30FI, IT-30CI(ID)

subzero.com/specs | 45

IT-36R(ID), IT-36CI(ID)

INTEGRATED REFRIGERATION

691/2"

(1765)

W 24" (610)

84"*

(2134)

41/2" (114)

35/8" (92)

*831/2" (2121) MIN TO 841/2" (2146) MAX

A

B

13/4" (45)

Specications

INTERIOR CAPACITY

COLUMN R CU FT (L) F CU FT (L)

IC-18FI 8.4 (238) IC-24R 12.9 (365) IC-24FI 12.3 (348) IC-30R(ID) 17.3 (490) IC-30FI 15.3 (433) IC-36R(ID) 21.4 (606)

TALL R CU FT

IT-30R(ID) 16.5 (467) IT-30FI 15.1 (428) IT-30CI(ID) 10.6 (300) 5.0 (142) IT-36R(ID) 20.5 (580) IT-36CI(ID) 13.3 (377) 6.4 (181)

DRAWER R CU FT

ID-24R 4.0 (113) ID-24F(I) 3.8 (108) ID-27R 4.6 (130) ID-30R(P) 5.2 (147) ID-30F(I) 4.9 (139) ID-30C(I) 3.0 (85) 2.0 (57) ID-36R(P) 6.6 (187) ID-36C(I) 3.4 (96) 2.5 (71)

(L) F CU FT (L)

Overall Dimensions

COLUMN

SHIPPING WEIGHT

COLUMN LB (KG)

18" Column 260 (118) 24" Column 340 (154) 30" Column 400 (181) 36" Column 440 (200)

TALL LB

30" Tall 400 (181) 36" Tall 460 (209)

DRAWER LB

24" Drawer 170 (77) 27" Drawer 190 (86) 30" Drawer 210 (95) 36" Drawer 250 (113)

IMPORTANT NOTE: Overall dimensions do not include panels

or handles. Dimensions will vary with panel thickness.

(KG)

COLUMN

MODEL W A B

18" Column 18" (457) 21/2" (64) 161/2" (419) 24" Column 24" (610) 4" (102) 221/2" (572) 30" Column 30" (762) 55/8" (143) 281/2" (724) 36" Column 36" (914) 71/4" (184) 341/2" (876)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

46 | Sub-Zero Customer Care 800.222.7820

INTEGRATED REFRIGERATION

183/8"

(467)

W 24" (610)

84"*

(2134)

109/16"

(268)

447/8"

(1140)

135/16"

(338)

3

/8" (10)

41/2"

(114)

35/8"

(92)

*831/2" (2121) MIN TO 841/2" (2146) MAX

3

/8" (10)

A

B

13/4" (45)

34

Overall Dimensions

TALL DRAWER

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

W

1

/2"*

(876)

*34" (864) MIN TO 35" (889) MAX

183/8"

(467)

135/16"

(338)

109/16"

(268)

24" (610)

1

(6)

/4"

3

(10)

/8"

35/8" (92)

TALL

MODEL W A B

30" Tall 30" (762) 55/8" (143) 281/2" (724) 36" Tall 36" (914) 71/4" (184) 341/2" (876)

DRAWER

MODEL W

24" Drawer 24" (610) 27" Drawer 27" (686) 30" Drawer 30" (762) 36" Drawer 36" (914)

subzero.com/specs | 47

INTEGRATED REFRIGERATION

NOTE:

SIDE

Opening Dimensions

INTEGRATED

H

OPENING

HEIGHT

(635)

25"

OPENING

DEPTH

TOP VIEW

OPENING WIDTH

OPENING DIMENSIONS

COLUMN AND TALL W H

18" Column 18" (457) 84" (2134) 24" Column 24" (610) 84" (2134) 30" Column and Tall 30" (762) 84" (2134) 36" Column and Tall 36" (914) 84" (2134)

DRAWER W H

24" Drawer 24" (610) 341/2" (876) 27" Drawer 27" (686) 341/2" (876) 30" Drawer 30" (762) 341/2" (876) 36" Drawer 36" (914) 341/2" (876)

The depth of each integrated model is 24" (610). Allow for panel thickness when planning the nished opening depth.

1

A minimum 3

/2" (89) nished return is required on all sides of the opening. Framed cabinets will require additional nished ller material behind the face frame for a proper installation. Refer to the illustration.

W

DUAL INSTALLATION

VIEW

31/2" (89) finished returns will be visible and should be finished to match cabinetry.

3

/4"

(19)

31/2" (89)

FINISHED

RETURN

W W

FRAMELESS CABINETRY

TYPICAL

FRONT VIEW

31/2" (89)

FINISHED

RETURN

FRAMED CABINETRY

FILLER

When installing two units side by side in a dual installation, the opening width is the width of the two units added together. A dual installation kit will be required for this installation. If a dual installation kit is not specied, a minimum

(51) ller strip is required between units.

2"

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

48 | Sub-Zero Customer Care 800.222.7820

INTEGRATED REFRIGERATION

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Electrical

The electrical supply must be located within the shaded area shown in the illustration and chart below. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

The electrical outlet must be positioned with the grounding prong to the right of the thinner blades.

Installation must comply with all applicable electrical codes.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

ELECTRICAL SUPPLY LOCATION

MODEL A

18" Model 6" (152) 24" Model 91/2" (241) 27" Model 11" (279) 30" Model 121/2" (318) 36" Model 151/2" (394)

Plumbing

The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self-piercing valves. The water supply line must not interfere with installation of the anti-tip bracket.

A reverse osmosis system can be used provided there is constant water pressure of 35–120 psi to the unit at all times. A copper line is not recommended for this application.

Installation must comply with all applicable plumbing codes.

PLUMBING REQUIREMENTS

Water Supply

Pressure 35–120 psi

Excess Line for Connection 36" (914)

WATER SUPPLY LOCATION

MODEL A

18" Model 3" (76) 24" Model 51/2" (140) 30" Model 6" (152) 36" Model 9" (229)

(2.4–8.3 bar) supplied

1

/4" OD copper, braided

stainless steel or PEX tubing

(2.4–8.3 bar)

LEFT SIDE

OF OPENING

41/2"

(114)

1

/4" (6)1/4" (6)

A

FLOOR

Electrical supply location.

41/4"

(108)

RIGHT SIDE

OF OPENING

6" (152)

A

3" (76)

1

AREA EXTENDS

FORWARD ON FLOOR

/2" (13)

Water supply location.

subzero.com/specs | 49

INTEGRATED REFRIGERATION

Custom Panels

For integrated models, custom door panels and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions.

The thickness of the custom panel can vary. A minimum

5

/8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 24"

(610). Allow for panel

thickness when planning the nished opening depth. Refer to the full-scale template on page 53.

CAUTION

As reveals between cabinetry and the unit decrease, severe nger pinching can occur while door is closing.

Finish all sides of custom panels. They will be visible when the door/drawer is open.

D-style handles are recommended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

18" Column 45 lb (20 kg)

24" Column 60 lb (27 kg)

30" Column 75 lb (34 kg)

36" Column 75 lb (34 kg)

WEIGHT PER PANEL MAX

30" Tall (door) 50 lb (22 kg)

36" Tall (door) 60 lb (27 kg)

Drawer 15 lb (7 kg)

PANEL THICKNESS MIN

All Panels

5

/8" (16)

TYPICAL PANEL DIMENSIONS

Column

79

(2029)

7

/8"

W

Tall

493/8"

(1254)

139/16"

(345)

1611/16"

(424)

WW

Drawer

Typical panel dimensions are based on an 84" (2134) nished

1

height for column and tall models and 34 models, with a 4"

(102) toe kick and

/2" (876) for drawer

1

/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths.

PANEL WIDTH

MODEL W

18" Model 173/4" (451) 24" Model 233/4" (603) 27" Model 263/4" (679) 30" Model 293/4" (756) 36" Model 353/4" (908)

DUAL INSTALLATION

For dual installations, refer to the illustration for panel heights and the chart below for panel widths.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

PANEL WIDTH

MODEL W

18" Model 1713/16" (452) 24" Model 2313/16" (605) 27" Model 2613/16" (681) 30" Model 2913/16" (757) 36" Model 3513/16" (910)

50 | Sub-Zero Customer Care 800.222.7820

INTEGRATED REFRIGERATION

Custom Panels

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

DOOR PANEL HEIGHT

The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below.

13/4"

(45)

A DECORATIVE VALANCE

1

/8" (3)

DOOR PANEL

84"

(2134)

HINGE

Upper valance—column and tall (side view).

CANNOT EXTEND

BEYOND THIS PLANE

24" (610)

TO BACK OF UNIT

TOE KICK CLEARANCE

The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from

(51) to 3

2"

7

/8" (98) require a reduced toe kick accessory available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

VENTED

LOUVERS

24" (610)

TO BACK OF UNIT

11/8" (29)

MAX

TOE KICK

ADJUSTMENT

A DECORATIVE TOE KICK

CANNOT EXTEND

BEYOND THIS PLANE

2" (51)*

TO

6" (152)

FROM

FLOOR

HINGE

DOOR PANEL

**

*2" (51) to 37/8" (98) requires sales accessory. **Column models only.

Toe kick (side view).

subzero.com/specs | 51

INTEGRATED REFRIGERATION

Standard Handles

Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

Refer to the chart below for standard handle lengths for integrated models.

HANDLE LENGTH

INTEGRATED TUBULAR PRO

Column Door 501/8" (1273) 483/8" (1229) Tall Door 331/4" (845) 311/2" (800) 24" Drawer 211/4" (540) 191/2" (495) 27" Drawer 241/4" (616) 221/2" (572) 30" Drawer 271/4" (692) 251/2" (648) 36" Drawer 331/4" (845) 311/2" (800)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

52 | Sub-Zero Customer Care 800.222.7820

INTEGRATED REFRIGERATION

Maximum Door Opening

FULL-SCALE TEMPLATE

As the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by utilizing the 90° door stop.

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

1

/8" (3) REVEAL

POTENTIAL

INTERFERENCE

ADJACENT

CABINETRY

3

/4" (19) PANEL

DOOR OPEN

MAXIMUM 105°

DOOR CLOSED 3

/4" (19) PANEL

1" (25)0"

SCALE

Maximum door opening (top view).

POTENTIAL INTERFERENCE

subzero.com/specs | 53

WINE STORAGE

Wine Storage

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Wine nds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced racks, soft lighting, custom cabinetry if desired—Sub-Zero helps make a wine collection an element of beauty in the home.

WINE STORAGE MODELS

KEY FEATURES

• Integrated, overlay, ush inset and stainless steel design

options.

• Full-view glass door standard on all models.

• Discreet interior lighting with illuminated display rack for

prized bottles of wine.

• Two independent storage zones maintain temperature,

humidity and UV protection.

• Full extension, cherrywood-faced wine racks for easy

access.

• Wine racks accommodate 750 ml bottles, half-bottles

and magnums.

• Inventory system helps organize wine collection.

• Freestanding model 424FSG does not require panels or

surrounding cabinetry.

• Model IW-30R features two refrigerator storage drawers.

315W

IW-18

424G

IW-24

424FSG

IW-30

IW-30R

WS-30

subzero.com/specs | 55

WINE STORAGE

Overall Dimensions

MODEL 315W

151/8" (384) 24" (610)

341/16"

(865)

4" (102)

165/8"

(422)

13/4" (44)

MODEL 424G

237/8" (606) 24" (610)

34"

(864)

4" (102)

253/8"

(645)

SPECIFICATIONS

STORAGE CAPACITY BOTTLES (750 ML)

315W 26 424G 46 424FSG 46

SHIPPING WEIGHT LB (KG)

315W 118 (54) 424G 195 (88) 424FSG 220 (100)

13/4" (44)

Overall dimensions are based on the stainless steel model. Refer to page 77 for door clearance information.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

56 | Sub-Zero Customer Care 800.222.7820

WINE STORAGE

W

OPENING WIDTH

341/2"

(876)

OPENING

HEIGHT

24" (610)

OPENING

DEPTH

TOP VIEW

SIDE VIEW FRONT VIEW

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Overall Dimensions

MODEL 424FSG

241/4" (616) 245/8" (625)

343/16"

(868)

4" (102)

253/8"

(645)

Opening Dimensions

MODEL 315W AND 424G

13/4" (44)

Freestanding model 424FSG has a nished stainless steel exterior and handles.

OPENING WIDTH

MODEL W

315W 151/4" (387) 424G 24" (610)

DUAL OPENING WIDTH

MODELS W

Two 24" Models 481/8" (1222)

Dual installation kit required.

subzero.com/specs | 57

WINE STORAGE

691/2"

(1765)

W 24" (610)

84"*

(2134)

41/2" (114)

35/8" (92)

*831/2" (2121) MIN TO 841/2" (2146) MAX

A

B

13/4" (45)

173/4"

(451)

W 24" (610)

84"*

(2134)

109/16"

(268)

447/8"

(1140)

135/16"

(338)

3

/8" (10)

41/2"

(114)

35/8"

(92)

*831/2" (2121) MIN TO 841/2" (2146) MAX

3

/8" (10)

A

B

13/4" (45)

Overall Dimensions

COLUMN

TALL

COLUMN

MODEL W A B

IW-18 18" (457) 21/2" (64) 161/2" (419) IW-24 24" (610) 4" (102) 221/2" (572) IW-30 30" (762) 55/8" (143) 281/2" (724)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

58 | Sub-Zero Customer Care 800.222.7820

TALL

MODEL W A B

IW-30R 30" (762) 55/8" (143) 281/2" (724)

IMPORTANT NOTE: Overall dimensions do not include panels

or handles. Dimensions will vary with panel thickness.

WINE STORAGE

Specications

INTERIOR CAPACITY

COLUMN BOTTLES (750 ML)

IW-18 59 IW-24 102 IW-30 146

TALL R CU FT (L) BOTTLES (750 ML)

IW-30R 4.0 (113) 86

SHIPPING WEIGHT

COLUMN LB (KG)

IW-18 350 (159) IW-24 410 (186) IW-30 460 (209)

TALL LB

IW-30R 490 (222)

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

(KG)

subzero.com/specs | 59

WINE STORAGE

NOTE:

SIDE

Opening Dimensions

INTEGRATED WINE STORAGE

(635)

25"

OPENING

DEPTH

OPENING DIMENSIONS

COLUMN AND TALL W H

18" Column 18" (457) 84" (2134) 24" Column 24" (610) 84" (2134) 30" Column and Tall 30" (762) 84" (2134)

H

OPENING

HEIGHT

TOP VIEW

W

OPENING WIDTH

The depth of each integrated (IW) model is 24" (610). Allow for panel thickness when planning the nished opening

1

depth. A minimum 3

/2" (89) nished return is required on all sides of the opening. Framed cabinets will require additional nished ller material behind the face frame for a proper installation. Refer to the illustration.

DUAL INSTALLATION

The unit can be installed next to an integrated refrigeration model or another integrated wine storage model in a dual installation. When installing two units side by side, the opening width is the width of the two units added together. A dual installation kit will be required for this installation. If a dual installation kit is not specied, a minimum 2"

(51) ller

strip is required between units.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

VIEW

31/2" (89) finished returns will be visible and should be finished to match cabinetry.

3

/4"

(19)

31/2" (89)

FINISHED

RETURN

W W

FRAMELESS CABINETRY

TYPICAL

FRONT VIEW

31/2" (89)

FINISHED

RETURN

FRAMED CABINETRY

60 | Sub-Zero Customer Care 800.222.7820

FILLER

WINE STORAGE

30" (762)

84"

(2134)

4"

(102)

733/4"

(1873)

237/8"

(606)

311/4"

(796)

17"

(432)

237/8" (606)

23/8" (60)

HEIGHT DIMENSIONS ±

1

/2" (13)

263/16" (665)

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Overall Dimensions

MODEL WS-30

Opening Dimensions

MODEL WS-30 STANDARD INSTALLATION

24" (610)

OPENING

DEPTH

833/4"

(2127)

OPENING

HEIGHT

TOP VIEW

W

OPENING WIDTH

SPECIFICATIONS

STORAGE CAPACITY BOTTLES (750 ML)

WS-30 147

SHIPPING WEIGHT LB (KG)

WS-30 445 (202)

Overall dimensions are based on the stainless steel model.

1

For ush inset applications, add

/2" (13) to door clearance

dimensions.

FRONT VIEWSIDE VIEW

NOTE: Shaded line represents profile of unit.

OPENING WIDTH

MODEL W

WS-30 291/2" (749)

If an 83" (2108) grille height is specied, the opening height

7

must be decreased by specied, the opening height must be increased by 4"

/8" (22). If an 88" (2235) grille height is

(102).

If two units are installed side by side, refer to page 63 for dual standard installations.

subzero.com/specs | 61

WINE STORAGE

*3

NOTE: Shaded line represents profile of unit with

SIDE

Opening Dimensions

MODEL WS-30 FLUSH INSET INSTALLATION

263/16"

(665)

FLUSH

INSET

23/16"

DEPTH

(56)

TOP VIEW

FINISHED

CLEATS*

1

/4"

(6)

84"

(2134)

FLUSH

INSET

HEIGHT

VIEW

" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.

11/4"

(32)

FLUSH INSET WIDTH

3/4" (19) panel.

W

FRONT VIEW

4" (102)

11/4"

(32)

3"

(76)*

TYPICAL

23/16"

(56)

FLUSH INSET WIDTH

MODEL W

WS-30 32" (813)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

62 | Sub-Zero Customer Care 800.222.7820

Dimensions assume a 3/4" (19) panel thickness.

If an 83" height must be decreased by

(2108) grille height is specied, the ush inset

7

/8" (22). If an 88" (2235) grille

height is specied, the ush inset height must be increased

(102).

by 4"

If two units are installed side by side, refer to page 64 for dual ush inset installations.

NOTE: Shaded line represents profile of unit.

SIDE

WINE STORAGE

Opening Dimensions

MODEL WS-30 DUAL STANDARD INSTALLATION

24" (610)

OPENING

DEPTH

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

TOP VIEW

VIEW

833/4"

(2127)

OPENING

HEIGHT

OPENING WIDTH

DUAL OPENING WIDTH

MODELS W

WS-30 and 30" Built-In 593/4" (1518) WS-30 and 36" Built-In 653/4" (1670)

W

FRONT VIEW

A dual installation kit will be required for this installation.

subzero.com/specs | 63

*3

NOTE: Shaded line represents profile of unit with

SIDE

WINE STORAGE

Opening Dimensions

MODEL WS-30 DUAL FLUSH INSET INSTALLATION

263/16"

(665)

FLUSH

INSET

23/16"

DEPTH

(56)

TOP VIEW

FINISHED

CLEATS*

1

/4"

(6)

84"

(2134)

FLUSH

INSET

HEIGHT

VIEW

" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry.

3/4" (19) panel.

11/4"

(32)

FLUSH INSET WIDTH

FRONT VIEW

W

11/4"

(32)

4" (102)

3"

(76)*

TYPICAL

23/16"

(56)

DUAL FLUSH INSET WIDTH

MODELS W

WS-30 and 30" Built-In 621/4" (1581) WS-30 and 36" Built-In 681/4" (1734)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

64 | Sub-Zero Customer Care 800.222.7820

Dimensions assume a 3/4" (19) panel thickness. A dual installation kit will be required for this installation.

WINE STORAGE

Electrical

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

The electrical supply must be located within the shaded area shown in the illustration for your specic model. For integrated (IW) models, also refer to the chart. For model 315W, the electrical supply can be located anywhere on the back wall of the opening. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

If the unit will be connected to a home security system, allow 36"

(914) of excess wiring for proper connection.

IMPORTANT NOTE: For integrated (IW) models, the electrical

outlet must be positioned with the grounding prong to the right of the thinner blades.

Installation must comply with all applicable electrical codes.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

ELECTRICAL SUPPLY LOCATION

INTEGRATED MODEL A

18" Model 6" (152) 24" Model 91/2" (241) 30" Model 121/2" (318)

LEFT SIDE

OF OPENING

41/2"

(114)

1

/4" (6)1/4" (6)

A

FLOOR

41/4"

(108)

Integrated models.

LEFT SIDE

OF OPENING

2"

(51)

Model 424G.

151/2"

(394)

FLOOR

3" (76)

751/2" (1918)

FROM FLOOR

Model WS-30.

7"

(178)

RIGHT SIDE

OF OPENING

E

6"

(152)

subzero.com/specs | 65

A

WINE STORAGE

Custom Panels

For framed, overlay, integrated and ush inset applications, a custom door panel must be provided. Handle hardware must also be provided for overlay, integrated and ush inset applications. Refer to panel requirements and custom panel dimensions charts for your specic model and design application.

Do not install a solid panel on a glass door unit. A solid door is available as a sales accessory (except model 315W and WS-30) and must be installed if a solid panel is being specied. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels.

Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models.

Model 424FSG has a nished stainless steel exterior that is designed to be used in a freestanding application.

Custom Panel—315W and 424G

For models 315W and 424G, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes.

Refer to the charts for panel requirements and dimensions.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

315W 10 lb (5 kg) 424G 10 lb (5 kg)

PANEL THICKNESS MIN

All Panels

OVERLAY PANEL DIMENSIONS

AA

315W, 424G

H

A

W

5

/8" (16)

PANEL DIMENSIONS

MODEL W H

315W 15" (381) 301/16" (764) 424G 233/4" (603) 301/16" (764)

STILES / RAILS (MIN) A

315W 21/4" (57) 424G 2

1

/4" (57)

DOOR CLEARANCE

Models 315W and 424G can be installed ush with surrounding cabinetry. Depending on the thickness of the overlay door panel, it may be necessary to install the unit

1

/4" (6) beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145°. Refer to the full-scale template on page 77.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

66 | Sub-Zero Customer Care 800.222.7820

WINE STORAGE

Custom Panel—Integrated

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

For integrated (IW) models, a custom door panel and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions.

Do not install a solid panel on the glass door unit. A solid door is available as a sales accessory through an authorized Sub-Zero dealer.

The thickness of the custom panel can vary. A minimum

5

/8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 24"

(610). Allow for panel

thickness when planning the nished opening depth. Refer to the full-scale template on page 53.

CAUTION

As reveals between cabinetry and the unit decrease, severe nger pinching can occur while door is closing.

Finish all sides of custom panels. They will be visible when the door/drawer is open.

D-style handles are recommended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

TYPICAL PANEL DIMENSIONS

Column

7

/8"

79

(2029)

W

Tall

493/8"

(1254)

139/16"

(345)

1611/16"

(424)

Typical panel dimensions are based on an 84" (2134) nished height, 4"

(102) toe kick and

1

/8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths.

PANEL WIDTH

MODEL W

18" Model 173/4" (451) 24" Model 233/4" (603) 30" Model 293/4" (756)

PANEL REQUIREMENTS

STILES / RAILS WIDTH

Stiles 31/4" (83) Top Rail 73/4" (197) Bottom Rail 91/2" (241) Bottom Rail (IW-30R) 41/2" (114)

WEIGHT PER PANEL MAX

Door Frame 35 lb (16 kg) Door Frame (IW-30R) 25 lb (11 kg) Drawer Panel 15 lb (7 kg)

PANEL THICKNESS MIN

All Panels

5

/8" (16)

DUAL INSTALLATION

For dual installations, refer to the illustration for panel heights and the chart below for panel widths.

PANEL WIDTH

MODEL W

18" Model 1713/16" (452) 24" Model 2313/16" (605) 30" Model 2913/16" (757)

subzero.com/specs | 67

WINE STORAGE

Custom Panel—Integrated

DOOR PANEL HEIGHT

The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below.

13/4"

(45)

A DECORATIVE VALANCE

1

/8" (3)

DOOR PANEL

84"

(2134)

HINGE

Upper valance (side view).

CANNOT EXTEND

BEYOND THIS PLANE

24" (610)

TO BACK OF UNIT

TOE KICK CLEARANCE

The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from

(51) to 3

2"

7

/8" (98) require a reduced toe kick accessory available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

VENTED

LOUVERS

24" (610)

TO BACK OF UNIT

11/8" (29)

MAX

TOE KICK

ADJUSTMENT

A DECORATIVE TOE KICK

CANNOT EXTEND

BEYOND THIS PLANE

2" (51)*

TO

6" (152)

FROM

FLOOR

HINGE

DOOR PANEL

**

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

68 | Sub-Zero Customer Care 800.222.7820

*2" (51) to 37/8" (98) requires sales accessory. **Column models only.

Toe kick (side view).

WINE STORAGE

AA

Custom Panel—WS-30

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

FRAMED PANEL

The framed application is an overlay model with framed design features. It is not a separate model.

1

If the custom panel is thinner than

/4" (6), a ller material

must be added to achieve a proper t. If the panel is thicker

1

/4" (6), rout an edge around the panel or mount the

than custom panel on a sheet of

1

/4" (6) thick material and insert

into the channel.

Routing, recessing and optional extended handles may be required for nger clearance. Refer to the full-scale template on page 78.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

Door 75 lb (34 kg) Grille (optional) 13 lb (6 kg)

PANEL THICKNESS MIN

Framed

1

/4" (6)

FRAMED PANEL DIMENSIONS

H

A

H

A

W

WS-30

FRAMED PANEL

PANEL W H

Door 293/4" (756) 699/16" (1767) Grille (optional) 293/4" (756) 815/16" (227)

STILES / RAILS A

Minimum 31/8" (79)

subzero.com/specs | 69

WINE STORAGE

AA

Custom Panel—WS-30

OVERLAY PANELS

Overlay panels are typically created by combining a 3/4" (19) custom panel, a .10"

(3) spacer panel and a

1

/4" (6) backer

panel. Refer to the illustrations below.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

Door 75 lb (34 kg) Grille 13 lb (6 kg)

PANEL THICKNESS MIN

Overlay

SPACER PANEL

CUSTOM PANEL

BACKER PANEL

DOOR FRAME

1

/8"

(3)

TRIM

5

/16" (8) min

GLASS

CUSTOM

3

/4"

(19)

typical

PANEL

.10" (3)

Panel assembly (cross section). Panel assembly (rear view).

1

/4" (6)

5

/8" (16)

SPACER

PANEL

BACKER

PANEL

OVERLAY PANEL DIMENSIONS

H

A

H

A

W

WS-30

OVERLAY PANELS

DOOR W H

Overlay Panel 30" (762) 693/4" (1772) Spacer Panel 291/8" (740) 6815/16" (1751) Backer Panel 293/4" (756) 699/16" (1767)

STILES / RAILS A

Minimum 31/4" (83)

GRILLE W H

Overlay Panel 30" (762) 91/4" (235)*

1

Spacer Panel 29

/8" (740) 85/16" (211)

Backer Panel 293/4" (756) 815/16" (227)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

70 | Sub-Zero Customer Care 800.222.7820

*Panel height may be increased by 7/16" (11) to hide upper main frame. For more information, refer to the built-in panel congurator at subzero.com/trade/panels.

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specic panel grille must be ordered for an 83" or 88" overall unit height.

WINE STORAGE

AA

Custom Panel—WS-30

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

FLUSH INSET PANELS

The ush inset application is an overlay model with ush inset panels. It is not a separate model.

The ush inset design allows custom panels to be installed ush with adjacent cabinets. Similar to overlay, ush inset

3

panels are typically created by combining a panel, a .10"

(3) spacer panel and a

1

/4" (6) backer panel.

/4" (19) custom

Refer to the illustrations for overlay panels on the previous page.

3

For ush inset panels thicker than

/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 81.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

Door 75 lb (34 kg) Grille 13 lb (6 kg)

PANEL THICKNESS MIN

Flush Inset

5

/8" (16)

FLUSH INSET PANEL DIMENSIONS

H

A

H

A

W

WS-30

FLUSH INSET PANELS

DOOR W H

Flush Inset Panel 31" (787) 693/4" (1772) Spacer Panel 291/8" (740) 6815/16" (1751) Backer Panel 293/4" (756) 699/16" (1767)

STILES / RAILS A

Minimum 33/4" (95)

GRILLE W H

Flush Inset Panel 31" (787) 91/4" (235) Spacer Panel 291/8" (740) 85/16" (211) Backer Panel 293/4" (756) 815/16" (227)

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specic panel grille must be ordered for an 83" or 88" overall unit height.

subzero.com/specs | 71

WINE STORAGE

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEW

5

/8"

(16)

5

/16" (8)

1

/2"

(13)

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

FLUSH INSET PANEL

SPACER

BACKER

DOOR DOOR

DOOR / DRAWER / GRILLE

TOP VIEWTOP VIEW

SIDE VIEW

CABINETRY

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

Custom Panel—WS-30

FLUSH INSET PANEL OFFSET

The illustrations provide panel offsets and reveals for model WS-30 in a ush inset application. Refer to the chart below for reference to the illustrations.

PANEL OFFSET

FLUSH INSET ILLUS

Door / Grille Sides A Grille Top B Grille Bottom / Door Top C Door Bottom D

5

/16"

TOP VIEW

(8)

DOOR / DRAWER / GRILLE

BACKER

SPACER

FLUSH INSET PANEL

Illus. A

GRILLE

DOOR

Illus. C

CABINETRY

5

/8"

(16)

5

/16"

5

(8)

3

5

/16"

(8)

SIDE VIEW

/32"

(4)

/32"

(2)

1

/2"

(13)

1

/2"(13)

Illus. B

Illus. D

CABINETRY

GRILLE

DOOR /

DRAWER

SIDE VIEW

1

5

/16"

(8)

SIDE VIEW

5

/16"

(8)

1

/8"

(3)

3

/2"(13)

/32"

(2)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

72 | Sub-Zero Customer Care 800.222.7820

WINE STORAGE

AA

Custom Panel—WS-30

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

DUAL INSTALLATIONS

If two models WS-30 or a model WS-30 and built-in unit are installed side by side, a dual installation kit may be required. Installations without a custom ller strip require a dual installation kit. If a dual installation kit is not specied, a 2"

(51)

ller strip is recommended between units. Dual installations without a ller strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

For dual standard installations, panel dimensions are the same as for single installations. Refer to the chart on page

70. Panel dimensions and offsets for dual ush inset installations are listed on the following pages.

DUAL FLUSH INSET PANEL DIMENSIONS

H

A

H

A

W

WS-30

MODEL WS-30

DOOR W H

Flush Inset Panel 301/2" (775) 693/4" (1772) Spacer Panel 291/8" (740) 6815/16" (1751) Backer Panel 293/4" (756) 699/16" (1767)

STILES / RAILS A

Minimum 33/4" (95)

GRILLE W H

Flush Inset Panel 301/2" (775) 91/4" (235) Spacer Panel 291/8" (740) 85/16" (211) Backer Panel 293/4" (756) 815/16" (227)

WITHOUT FILLER STRIP

Opposite hinges.

FILLER STRIP

Same side hinges.

Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). A specic panel grille must be ordered for an 83" or 88" overall unit height.

subzero.com/specs | 73

WINE STORAGE

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEW

5

/8"

(16)

5

/16"

(8)

1

/2"

(13)

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

FLUSH INSET PANEL

SPACER

BACKER

DOOR DOOR

DOOR / DRAWER / GRILLE

TOP VIEWTOP VIEW

SIDE VIEW

CABINETRY

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

1

/2"(13)

3

/32"

(2)

5

/16"

(8)

5

/16"

(8)

5

/32"

(4)

GRILLE

DOOR

1

/4" (6)

REVEAL

5

/16" (8)

1

/8" (3)

DOOR DOOR

TOP VIEWTOP VIEW

Custom Panel—WS-30

DUAL FLUSH INSET PANEL OFFSET

The illustrations provide panel offsets and reveals for model WS-30 in a dual ush inset application. Refer to the chart below for reference to the illustrations.

PANEL OFFSET

DUAL FLUSH INSET ILLUS

Door (hinge) / Grille Sides A Door (handle) Sides B Grille Top C Grille Bottom / Door Top D Door Bottom E

DOOR / DRAWER / GRILLE

BACKER

SPACER

TOP VIEW

CABINETRY

DOOR DOOR

TOP VIEW

DUAL TRIM

FLUSH INSET PANEL

5

(8)

/16"

5

/8"

(16)

1 (13)

/2"

Illus. A

CABINETRY

1

/2"(13)

1

/8"

5

/16"

GRILLE

(3)

(8)

SIDE VIEW

Illus. C

DOOR /

DRAWER

5

/16"

(8)

5

/16" (8)

Illus. B

DOOR

Illus. D

1

/8" (3)

GRILLE

1

/4" (6)

REVEAL

5

/16"

(8)

5

/16"

(8)

SIDE VIEW

5

/32"

(4)

1

/2"(13)

3

/32"

(2)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

74 | Sub-Zero Customer Care 800.222.7820

3

/32"

SIDE VIEW

(2)

Illus. E

WINE STORAGE

84"

(2134)

24" (610)

OPTIONAL

TOE KICK CUT-OUT

4" (102)

17/8"(48)

1" (25)

ROUT TO

1

/8" (3)

FRONT

OF SIDE

PANEL

25/8"

(67)

MAIN

FRAME

SIDE PANEL

ROUTING

1" (25)

17/8" (48)

1

/8" (3)

1

/2" (13)

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Custom Panel—WS-30

SIDE PANEL

The custom side panel must be a minimum of 24" (610) deep

1

/2" (13) thick. Routing will be necessary for the side

and panel to t ush against the side of the unit. Refer to the illustrations below.

When installing model WS-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

Standard Handles

Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

Refer to the chart below for standard handle lengths for wine storage models.

HANDLE LENGTH

WINE STORAGE TUBULAR PRO

315W, 424G Door 241/4" (616) 221/4" (572) IW-18, IW-24, IW-30 Door 501/8" (1273) 483/8" (1229) IW-30R Door 331/4" (845) 311/2" (800) IW-30R Drawer 241/4" (616) 221/2" (572) WS-30 Door 637/8" (1622) 453/16" (1147)

Side panel dimensions.

Routing detail.

subzero.com/specs | 75

WINE STORAGE

Wine Rack Wood Facing

FULL-SCALE TEMPLATE

The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for prole dimensions of the wood facing and the chart for width.

7

/64" (3)

11/16"

(27)

5

/64" (2)

1

(13)

9

/2"

23

/16"

(14)

1

(9)

/4"

(6)

11/2"

(38)

/64"

5

/8"

(16)

7

(3)

/64"

27

/32"

(21)

23

/64"

(9)

9

/16"

(14)

5

/64" (2)

WOOD FACING WIDTH

MODEL WIDTH

315W 1015/16" (278) 424G, 424FSG 191/2" (495) IW-18 115/8" (295) IW-24 175/8" (448) IW-30, IW-30R 235/8" (600) WS-30 249/16" (624)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

IW-18, IW-24,

IW-30, IW-30R

315W, 424G,

424FSG, WS-30

Wine rack wood facing prole.

76 | Sub-Zero Customer Care 800.222.7820

WINE STORAGE

Door Clearance—315W and 424G

FULL-SCALE TEMPLATE

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

To allow for a 145° door opening, the unit should extend

1

a minimum of

/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed ush, however, there is potential for interference with the panel if the door is opened past 90°.

UNDERCOUNTER

UNIT

DOOR CLOSED

1

/2"

(13)

ADJACENT

CABINETRY

1" (25)0"

SCALE

145° door opening (top view).

3

/4" (19) DOOR PANEL

1

/4"

(6)

1

/8" (3)

HINGE AT 145°

OPENING

(DOOR OPENS PAST 145°)

subzero.com/specs | 77

WINE STORAGE

Framed Panel—WS-30

FULL-SCALE TEMPLATE

OPTIONAL EXTENDED FULL-LENGTH HANDLE

1"

(25)

1

/4" (6) FRAMED PANEL

STANDARD FULL-LENGTH HANDLE

2"

(51)

DOOR

3"

(76)

11/4" (32) PANEL

1" (25) PANEL

3

/4" (19) PANEL

1

/2" (13) PANEL

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

Framed panel thickness.

78 | Sub-Zero Customer Care 800.222.7820

WINE STORAGE

Overlay and Flush Inset Panels—WS-30

FULL-SCALE TEMPLATE

Overlay and ush inset panels must be a minimum of 5/8"

(16)

thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door.

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

1"

(25)

1

/4" (6) BACKER PANEL

DOOR

DEPTH OF TUBULAR AND PRO HANDLES

2"

(51)

3"

(76)

11/4" (32) PANEL

1" (25) PANEL

3

/4" (19) PANEL

.10" (3) SPACER PANEL

Overlay and ush inset panel thickness.

subzero.com/specs | 79

WINE STORAGE

237/8"

(606)

TO REAR OF UNIT

OVERALL WIDTH OF UNIT

1

/

4

"

(32)

1

/

2

"

(38)

1

3

/

4

"

(44)

0"

(0)

1"

(25)

2"

(51)

2

1

/

4

"

(57)

2

1

/

2

"

(63)

2

3

/

4

"

(70)

3"

(76)

3

1

/

4

"

(83)

3

1

/

2

"

(89)

1

/

4

"

(6)

1

/

2

"

(13)

3

/

4

"

(19)

3

/4"

(19) THICK

OVERLAY PANEL

(TYPICAL)

1

/4"

(6) BACKER

PANEL

1"

(25) THICK

PANEL

Overlay Application—WS-30

FULL-SCALE TEMPLATE

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

90° door opening (top view).

80 | Sub-Zero Customer Care 800.222.7820

1" (25)0"

SCALE

WINE STORAGE

Flush Inset Application—WS-30

24"

FULL-SCALE TEMPLATE

For panels thicker than 3/4" (19), a 90° door stop may be required to prevent interference with adjacent cabinets.

(610)

TO BACK WALL

23/16"

(56)

ASSUMES

3

/4" (19)

FLUSH INSET

PANEL

THICKNESS

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

11/4" (32)

1" (25) THICK

PANEL

3

/4" (19) THICK

FLUSH INSET PANEL

(TYPICAL)

1

/4" (6) BACKER

PANEL

110° door opening (top view).

1" (25)0"

SCALE

subzero.com/specs | 81

WINE STORAGE

FILLER STRIP

11/4" (32)

APPROX PROFILE OF

STAINLESS STEEL WRAPPED

DOOR AND HANDLE

Dual Standard Installation—WS-30

FULL-SCALE TEMPLATE

Typical framed, overlay or stainless steel dual installation with ller strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

DOOR

CLOSED

DOOR

OPEN 110°

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

1" (25)0"

SCALE

Dual standard installation (top view).

82 | Sub-Zero Customer Care 800.222.7820

WINE STORAGE

FILLER STRIP

11/2" (38)

1

/2" (13)

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

PROFILE OF

3

(19) FLUSH INSET PANEL

/4"

AND TUBULAR HANDLE

Dual Flush Inset Installation—WS-30

FULL-SCALE TEMPLATE

Typical ush inset dual installation with ller strip at maximum 110° door opening. Panel thickness may require a 90° door stop.

DOOR

CLOSED

DOOR

OPEN 110°

1" (25)0"

SCALE

Dual ush inset installation (top view).

subzero.com/specs | 83

UNDERCOUNTER REFRIGERATION

Undercounter Refrigeration

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Sub-Zero undercounter refrigeration is a helpful addition to a master suite, bar, home ofce or media room. In the kitchen, a high-volume ice machine is a must for entertaining. The design exibility of these compact yet roomy units makes them all the more welcome in any room or outdoor kitchen. They are ready to be tted with a custom cabinet panel or can be ordered with a stainless steel panel.

UNDERCOUNTER MODELS

UC-24R

UC-24BG

UC-24C(I)

KEY FEATURES

• Overlay and stainless steel design applications.

• Handle options coordinate with handles of Wolf cooking

products.

• Models UC-24RO and UC-15I(P)O are UL approved for

outdoor use.

®

• Energy efcient; many models are ENERGY STAR

qualied.

• Star-K certied (except ice machine models).

UC-24RO

UC-15I(P)

UC-15I(P)O

subzero.com/specs | 85

UNDERCOUNTER REFRIGERATION

Overall Dimensions

UNDERCOUNTER

237/8" (606)

34"

(864)

253/8"

(645)

4" (102)

24" (610)

ICE MACHINE

143/4" (375) 23" (584)

335/8"

(854)

4" (102)

18"

(457)

6"

(152)

26" (660) 8"

(203)

SPECIFICATIONS

INTERIOR CAPACITY R CU FT (L) F CU FT (L)

UC-24R, UC-24RO 5.7 (161) UC-24BG 6.0 (170) UC-24C(I) 3.6 (102) 1.1 (31)

SHIPPING WEIGHT LB

24" Model 130 (59)

Refer to page 91 for door clearance information.

(KG)

SPECIFICATIONS

STORAGE CAPACITY LB (KG)

UC-15I(P), UC-15I(P)O 26 (12)

SHIPPING WEIGHT LB

(KG)

Ice Machine 100 (45)

Model UC-15I overall dimensions do not include panel or handle.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

86 | Sub-Zero Customer Care 800.222.7820

UNDERCOUNTER REFRIGERATION

W

OPENING WIDTH

341/2"

(876)

OPENING

HEIGHT

24" (610)

OPENING

DEPTH

TOP VIEW

SIDE VIEW FRONT VIEW

Opening Dimensions

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

UNDERCOUNTER

DUAL INSTALLATION

If two units are installed side by side, a dual installation kit may be required. Installations without a custom ller strip require a dual installation kit. If a dual installation kit is not specied, a 2"

(51) ller strip is recommended between units.

Dual installations without a ller strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com. For questions regarding the installation, call Sub-Zero customer care at 800-222-7820.

OPENING WIDTH

MODEL W

24" Model 24" (610) Ice Machine 151/4" (387)

DUAL OPENING WIDTH

MODELS W

Two 24" Models 481/8" (1222)

Dual installation kit required.

WITHOUT FILLER STRIP

Opposite hinges.

FILLER STRIP

Same side hinges.

subzero.com/specs | 87

UNDERCOUNTER REFRIGERATION

Electrical

The electrical supply should be located within the shaded area shown in the illustration. For ice machine models, it is recommended that electrical supply be placed in an adjacent cabinet. A separate circuit, servicing only this appliance is required.

IMPORTANT NOTE: For outdoor models UC-24RO and

UC-15I(P)O, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock. A GFCI is not recommended for use with other undercounter models and may cause interruption of operation.

Installation must comply with all applicable electrical codes.

LEFT SIDE

OF OPENING

2"

151/2"

(51)

(394)

3" (76)

FLOOR

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

Electrical supply location.

88 | Sub-Zero Customer Care 800.222.7820

UNDERCOUNTER REFRIGERATION

24" (610)

ROUGH

OPENING

DEPTH

Plumbing

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

The water supply line should be located within the shaded area shown in the illustrations below. The water supply line should be connected to the house supply with an easily accessible shut-off valve between the supply and the unit. Do not use self-piercing valves. A saddle valve kit is avail able through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

IMPORTANT NOTE: A reverse osmosis system can be used

provided there is constant water pressure as indicated in the chart below at all times. A copper line is not recommended for this application.

PLUMBING REQUIREMENTS

1

Water Supply

Pressure (UC-24CI) 20–100 psi

Pressure (UC-15I) 20–80 psi (1.4–5.5 bar)

Excess Line for Connection 36" (914)

/4" OD copper, braided

stainless steel or PEX tubing

(1.4–6.9 bar)

ICE MACHINE DRAIN

Ice machine models can be ordered with or without a drain pump. Models without a pump will drain water by gravity. A drain must be installed.

The drain and inlet water tubes must be plumbed before connecting to the ice machine. For the gravity drain, hori-

1

zontal drain lines must have a

/4" (6) per 12" (305) fall. An air gap will likely be required between the unit and drain. A stand pipe with a trap below is acceptable for the drain.

LEFT SIDE

OF OPENING

2"

151/2"

(51)

(394)

AREA EXTENDS

FORWARD ON FLOOR

Model UC-24CI.

1

/2" (13)

3" (76)

Ice machine.

8"

(203)

1

/2"

(13)

LOCATION OF

WATER LINE

TOP VIEW

subzero.com/specs | 89

UNDERCOUNTER REFRIGERATION

Custom Panel

For overlay undercounter models, custom door panels and handle hardware must be provided. Refer to the charts for panel requirements and dimensions.

Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

UC-24R, UC-24C(I) 20 lb (9 kg) UC-24BG 10 lb (5 kg) UC-15I(P) 15 lb (7 kg)

PANEL THICKNESS MIN

All Panels

5

/8" (16)

MODEL UC-24BG

For model UC-24BG, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. Refer to the illustration below.

Do not install a solid panel on a glass door unit. A solid door is available as a sales accessory and must be installed if a solid panel is being specied. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels.

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

90 | Sub-Zero Customer Care 800.222.7820

UNDERCOUNTER REFRIGERATION

A

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

Custom Panel

OVERLAY PANEL DIMENSIONS

H

W

UC-24R, UC-24C(I), UC-15I(P)

PANEL DIMENSIONS

MODEL W H

24" Model 233/4" (603) 301/16" (764) Ice Machine 15" (381) 303/8" (772)

STILES / RAILS (MIN) A

UC-24BG 21/4" (57)

AA

W

UC-24BG

DOOR CLEARANCE

Undercounter models can be installed ush with surrounding cabinetry. Depending on the thickness of the custom door panel, it may be necessary to install the unit beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145°. Refer to the full-scale template on page 93.

H

A

1

/4" (6)

Standard Handles

Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the nd a showroom section of our website, subzero.com.

Refer to the chart below for standard handle lengths for undercounter models.

HANDLE LENGTH

UNDERCOUNTER TUBULAR PRO

Door 241/4" (616) 221/2" (572) Outdoor Door NA 1511/16" (399)

subzero.com/specs | 91

UNDERCOUNTER REFRIGERATION

Wine Rack Wood Facing

FULL-SCALE TEMPLATE

The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for prole dimensions of the wood facing and the chart for widths.

7

/64" (3)

11/16"

(27)

5

/64" (2)

1

(13)

9

/2"

23

/16"

(14)

1

(9)

/4"

(6)

11/2"

(38)

/64"

5

/8"

(16)

7

(3)

/64"

27

/32"

(21)

23

/64"

(9)

9

/16"

(14)

5

/64" (2)

WOOD FACING WIDTH

MODEL WIDTH

UC-24BG, UC-24C(I) 191/2" (495)

UNDERCOUNTER WINE INTEGRATED PRO 48 BUILT-IN

IW-18, IW-24,

IW-30, IW-30R

315W, 424G,

424FSG, WS-30

Wine rack wood facing prole.

Sub-Zero, Sub-Zero & Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service marks of Sub-Zero, Inc. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.

92 | Sub-Zero Customer Care 800.222.7820

UNDERCOUNTER REFRIGERATION

Door Clearance—Undercounter

FULL-SCALE TEMPLATE

BUILT-IN PRO 48 INTEGRATED WINE UNDERCOUNTER

To allow for a 145° door opening, the unit should extend

1

a minimum of

/4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed ush, however, there is potential for interference with the panel if the door is opened past 90°.

UNDERCOUNTER

UNIT

DOOR CLOSED

1

/2"

(13)

ADJACENT

CABINETRY

1" (25)0"

SCALE

145° door opening (top view).

3

/4" (19) DOOR PANEL

1

/4"

(6)

1

/8" (3)

HINGE AT 145°

OPENING

(DOOR OPENS PAST 145°)

subzero.com/specs | 93

Sub-Zero Residential Limited Warranty

FOR RESIDENTIAL USE

FULL TWO YEAR WARRANTY*

For two years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.

FULL FIVE YEAR SEALED SYSTEM WARRANTY

For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.

LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY

For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. If the owner uses Sub-Zero factory certied service, the service provider will repair or replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certied service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certied service or other sources.

TERMS APPLICABLE TO EACH WARRANTY

The warranty applies only to products installed for normal residential use. The warranty applies only to products installed in any one of the fty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also have other legal rights that vary from state to state.

To receive parts and/or service and the name of Sub-Zero factory certied service nearest you, contact Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website, subzero.com, email us at customerservice@subzero.com or call 800-222-7820.

*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects.

*Replacement water lters and air purication cartridges are not covered by the product warranty.

Sub-Zero Outdoor Limited Warranty*

FOR RESIDENTIAL USE

FULL ONE YEAR WARRANTY**

For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.

FULL FIVE YEAR SEALED SYSTEM WARRANTY

For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.

TERMS APPLICABLE TO EACH WARRANTY

The warranty applies only to products installed for normal residential use. The warranty applies only to products installed in any one of the fty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC. WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also have other legal rights that vary from state to state.

To receive parts and/or service and the name of Sub-Zero factory certied service nearest you, contact Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website, subzero.com, email us at customerservice@subzero.com or call 800-222-7820.

*Product must be approved for outdoor use, designated by model and serial number.

**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects.

**Replacement water lters are not covered by the product warranty.

SUB-ZERO, INC. P.O. BOX 44848 MADISON, WI 53744 SUBZERO.COM 800.222.7820

Thermador IT30R Design Guide

Specifications and Main Features

Frequently Asked Questions

User Manual