Thermador CIS365GB/02, CIT304GB-01 Installation Guide

INSTALLATION INSTRUCTIONS

For Induction Cooktop

Model: CLT304...

CLT365... CLS365...

In/_T_l_n In,a]3GSl_nA

In,ai31331_nA d'ln/_7_l_n InAi3C_3!_neA de InAi_.3!£n

3-13

14 - 24 25 - 35

Thermador ° An AmericanIcon_"

Table of contents

Important Safety Instructions ......................................

Before you begin .................................................

Tools and parts needed .............................................

Parts included .....................................................

Preparation .......................................................

Installation procedure .............................................

Installing the heat shield .............................................

Install the gasket ...................................................

Secure the cooktop to countertop ....................................

Electrical installation ................................................

Test the installation .................................................

Technical service .................................................

4 5 5

5 6 9

10 10

11 12

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

Impo_ant

Safe appliance handling Hidden surfaces may have sharp edges. Use caution when reaching behind or

Electrical safety Before installing, turn off at the service panel. Lock service panel to prevent power

SAVE THESE INSTRUCTIONS FOR LOCAL INSPECTOR'S USE THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN

LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE AFTER INSTALLATION IS COMPLETE.

WARNING: Ifthe information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury.

WARNING: Do not repair or replace any part of the appliance unless specifically recommended in the manual. Never modify or alter the construction of the appliance. Improper installation, technical service or maintenance can cause injury or property damage. Refer to this manual. Consult with a factory authorized service center for all repairs.

Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material.

under appliance.

from being turned on accidentally. The circuit breaker should have a contact separation of at least 3 mm. on all poles.

Be sure your appliance is properly installed and grounded by a qualified technician. Have the installer show you the location of the circuit breaker or fuse. Mark it for

easy reference. This appliance has been tested in accordance with ANSI/UL 858 Standard for

Safety for Household Electric Ranges and CAN/CSA-22.2 No. 61 National Standard of Canada for Household Cooking Ranges. It is the responsibility of the owner and installer to determine if additional requirements and standards apply in specific installations.

Related equipment safety This stove is guaranteed safe for use only if it is installed by a specialist pursuant to

the installation instructions. The installer is responsible for any damage caused due to improper installation.

To eliminate the risk of burns or fire when touching hot surface units, avoid leaving storage space in the cabinets over the surface units. Inthe event of presence of

storage in cabinets, the risk can be reduced by installing a hood that extends horizontally at least 5 inches (12.7 cm) from the cabinet bottom.

Do not install refrigerators, dishwashers, unvented ovens, or washers that may fit below the cooktop.

Note: We strongly recommend the installation of a ventilation system with this appliance.

Before you begin

Tools and parts needed

Parts included

÷ Phillips head screwdriver ÷ Pencil

÷ Drillwith 1/4" (6.35 mm) bit ÷ Jigsaw

÷ Tape measure Note: Additional materials may be necessary for installation in solid surface

countertops. Contact the countertop manufacturer.

÷ Hold down brackets (4) ÷ Clamping screws #10-32 x 2 1/2" (63.8 mm) (4)

÷ Sheet metal screws #8 x 3/8" (9.5 mm) (4) ÷ Gasket

Preparation

Countertop requirements

_ WARNING: To reduce the risk of ignition of nearby combustible materials,install the countertop with a minimum distance of 2" (51mm) from both side

walls and the back wall.

Note

30" Models: 01T304...

I . I

min"301(762mm)I

min. 2" _ min. 2"

I (51 mm) 51 mm)

The work surface should be horizontal and level. The stability of the countertop should be confirmed even after making the cutout.

After preparing cutout, remove shavings as they can affect the function of electrical components.

Seal the surfaces of the cutout to make them heat resistant. This prevents the surfaces from expanding as a result of humidity.

Solid surface countertops often require special installation. For example, heat reflective tape or rounded corners may be necessary. Contact the countertop manufacturer for instructions specific to your countertop.

Q1/4" (6 mm)

19 7/8 - 2O"

(505 - 508 mm

min. 2" (51 mm)

min. 2 1/4" (57 mm)

.28 3/4 - 28 7/8"

(731 - 734mm)

36" Models: CIT365...

CIS365...

I ,, I I

min" 30 1(762mm)I

min. 2" _ min. 2"

1/ // "\\ \

19 7/8 - 20"

(505 - 508 mm

G11/4"(6 mm)

min. 2" (51 mm)

min. 2 1/4" (57 mm)

3/4 - 34 7/8"

(883 - 886mm)

Cabinet requirements The distance from the top of the cooktop to the bottom of the cabinets above it

must be A -- 30" (762 mm) minimum. This distance can be reduced to A -- 24" (610 mm) when the bottom of the wood or metal cabinet is protected by not less than 1/4" (6.35 mm) flame retardant millboard, covered by no. 28 steel sheet

0.015" (0.4 mm) thick stainless steel, 0.024" (0.6 mm) aluminum, or 0.020" (0.5 mm) thick copper, at a minimum. Verify that the cabinets above the cooktop are a

maximum of B--13" (330 mm) deep.

i Building side wall

Cooking surface

Installation procedure

_ ARNING: To avoid injury, use protective gloves when installing the plateand when handling/installing the cooktop. Stainless steel parts could have

sharp edges.

Installing the heat shield

For safety reasons, the heat shield must be properly installed. This prevents components from overheating as a result of the recirculation of hot air from the cooktop.

The heat shield is the same width as the cooktop. For shipping, it is screwed to the burner box.

After unpacking the cooktop, unscrew the heat shield (see illustration).

The heat shield will be able to rotate freely, as shown in the illustration.

Install the gasket

Turn the cooktop over and attach the gasket to the edge of the cooktop (see illustration).

Secure the cooktop to countertop

Not to let the glass to "drop" into place and that it needs to be supported along a broad area of the edges when "placing" the cooktop into the cutout.

The cooktop should be secured to the countertop using the clamping brackets provided.

Before inserting the cooktop into the cutout, turn the cooktop upside down and attach brackets to the burner box using the screws.

Place cooktop into cutout. Insert clamping screw into the bracket and secure cooktop to countertop.

Use a wood block to protect fragile countertop materials.

Electrical installation

Electrical requirements You can find the identification plate with the electrical specifications on the

underside of the appliance. The junction box must be located within 3 feet (-900 mm) of the cooktop connection. It should be easily accessible for service

purposes.

3 1/4" max (79 mm)+ Fitting/Conduit1"(23 mm)

12" approx. (300 mm,_-A--

Connection ("J") box

_] 1" min(26 mm) air clearance

Conduit approx. 3 ft. (~900 mm)

Power supply

01T304 Models...

40 Amp circuit breaker 240 Volts, 3 Wire, 60 Hz 208 Volts, 3 Wire, 60 Hz

All with 39" (1m) flexible conduit (included)

01T365 and 01S365 models...

50 Amp circuit breaker 240 Volts, 3 Wire, 60 Hz 208 Volts, 3 Wire, 60 Hz

All with 39" (1m) flexible conduit included

Electrical connection

_ AUTION: Before installing, turn off at the service panel. Lock servicepanel to prevent power from being turned on accidentally.

The branch-circuit breaker ampacity, the wire sizes and the connections must meet the requirements of the National Electrical Code (or Canadian Electrical Code) and

all local codes and ordinances. Attach flexible conduit to the junction box.

_ ARNING: To reduce the risk of electric shock and fire, do not use aflexible power supply cord.

Connect the cooktop lead wires to the junction box supply wires in the following order:

black (L1) to black red (L2) to red green wire to ground

Test the installation

Redwire cord

CertifiedUL connector

Groundedgreen Cooktoppower supply

cable cord

Housepower supply

Black wire

Junction box

If the cooktop is installed and connected as specified above, it will be completely grounded in compliance with the National Electrical Code.

_ AUTION: Before plugging in the electrical cord, be sure all controls are inthe OFF position.

Remove everything from the cooktop surface, including stickers. Clean cooktop surface with cooktop cleaning cream. Turn on the power supply.

Verify that elements function properly.

+ 24 hidden pages