Thermador CHMHP486N, CHMHP4812N Installation Manual
CHIMNEY EXTENSION
INSTALLATION
THERMADOR PROFESSIONALTM Chimney Hoods
INSTALLATION DES RALLONGES
DE CONDUIT
Hottes avec conduit PROFESSIONALMC de THERMADOR
INSTALACIÓN DE LOS
Models/
Modèles/
Modelos:
CHMHP366N
CHMHP486N
CHMHP3612N
CHMHP4812N
CHMHP36TSN
CHMHP48TSN
ALARGADORES DE CONDUCTO
Campanas con conducto PROFESSIONALTM de
THERMADOR
Chimney Extension Installation
2
18” (457)
B
A
18” – 35”
( 457 – 889)
⅝” (16)
18”
(457)
17”
(432)
AB
36" 14" (356) 20¾" (527)
48" 14" (356) 32⅞" (835)
Chimney extensions fill the space between the hood and
ceiling of 8' (2.4 m) and 9' (2.7 m) ceilings. Telescoping
extensions accommodate 10' (3 m) ceilings.
Model 6'' Ext. 12'' Ext. Telescoping
HPCN36NS CHMHP366N CHMHP3612N CHMHP36TSN
HPCB36NS CHMHP366N CHMHP3612N CHMHP36TSN
HPCN48NS CHMHP486N CHMHP4812N CHMHP48TSN
HPCB48NS CHMHP486N CHMHP4812N CHMHP48TSN
Chimney Extension Installation
IMPORTANT NOTE: Secure the Chimney Hood to the wall
before installing the Chimney Extension. See the
Installation Manual before securing the actual Extension.
1. Installation of the chimney hood should maintain a
minimum height of 30" (762 mm) from the bottom of the
hood to the cooking surface. To determine placement
of the hood with a Chimney Extension, the height of the
chimney extension must be calculated (see the
Installation Manual).
2. From inside of hood, screw the supplied 5/8” (16 mm)
sheet metal screws through the holes on each side and
along the front into bottom of the extension, as shown.
(Screw quantity is dependent on hood size.)
Telescoping Chimney Extension
Installation
IMPORTANT NOTE:
Secure the Chimney Hood to the wall after installing the
Extension Mounting Bracket, but before installing the
Telescoping Chimney Extension. See the Chimney Hood
Installation Manual before securing the actual Extension.
Securing the Telescoping Chimney Extension Bracket
1. Ensure that the minimum height of 30" (762 mm) from
the bottom of the hood to the cooking surface will be
maintained (see the Installation Manual).
2. Locate two studs at the mounting location, as shown.
measurements in inches (mm)
B
B
⅝” (16)
A
17”
17”
(432)
(432)
18”
18”
(457)
(457)
18” – 35”
18” – 35”
( 457 – 889)
( 457 – 889)
1
18” (457)
18” (457)
3. At the wall stud locations, measure ǫ” (16 mm) down
from the ceiling to the top of the bracket.
English 1
4. Mount the bracket at the wall stud locations using (2)
3½” (89)
1½” (38 mm) screws (provided). Ensure that the
bracket is level.
measurements in inches (mm)
Adjustable
mount holes
7. Carefully pull the top part of the extension upwards.
Screw the left and right sides of the extension to the
mounting bracket with the supplied stainless screws.
2
3½” (89)
3½” (89)
5. See “Hanging the Chimney Hood” in the Installation
Manual before securing the Telescopic Chimney
Extension.
6. Insert the complete duct cover at an angle and swivel
toward the wall.
2
1
8. From inside of hood, screw the supplied 5/8” (16 mm)
sheet metal screws through the holes on each side and
along the front into bottom of the extension. Screw
quantity is dependent on hood size.
1
English 2
Loading...