Thermaco Trapzilla TZ-600 Specifications
37"
4.5"
U.S. and International Patents Issued and Pending
www. .com
SOLIDS
DO NOT USE
MECHANICAL CRUST
BREAKING DEVICES
GREASEGREASE
Trapzilla® Grease Trap System
TZ-600 Specications
FEATURES:
• Offers a at grease separation curve
• Constructed of corrosion resistant
materials suitable for installation in
virtually any location.
• Compact footprint.
TOP VIEW
2" VENT
36.5"
AA
4.5"
36"
INLETOUTLET
14.125"
37"
49.5"
Conforms to ASME Standard
ASME A112.14.3-2000
®
29” CLEARANCE FROM
TOP OF TANK REQUIRED FOR LID REMOVAL
4" PIPE�
INLET/OUTLET
®
END VIEWSIDE VIEW
31"
TECHNICAL DATA
Materials:
ASME A112.14.3 (Tested) Flow Rating:
Manufacturer Rated Inlet Flow Rating:
Grease Retention Capacity:
©2008 Thermaco, Inc. • All rights reserved • Patented/Patents Pending • Specications subject to change without notice
8/08
Thermaco, Inc. • PO Box 2548 • Asheboro, NC 27204-2548 • Phone: (336) 629-4651 • Online: www.big-dipper.com
Rotationally Molded Polyethylene
75 GPM
150 GPM
600+ Pounds
1
INSTALLATION INFORMATION
Suggested Minimum Footprint Dimensions
The Trapzilla® requires 6”
of clearance all the way
around the lid.
Trapzilla® Grease Trap System
www. .com
U.S. and International Patents Issued and Pending
TZ-600 Specications
DO . . .
READ instruction manual included with
system before doing anything.
Install unit allowing for the minimum
clearances shown.
Make piping connections with rubber
“No Hub” connectors.
Keep outlet piping as straight as possible. Use only “sweep” connections.
Install vent on outlet piping.
DON’T . . .
DO NOT USE
MECHANICAL CRUST
BREAKING DEVICES
Install “P” trap on outlet connection
of tank. (Note: the unit already has
an internal gas trap).
SOLIDS
AA
Reduce pipe size on outlet piping.
GREASEGREASE
NOTE: Drawing for reference only. Equipment must be installed in compliance with
all applicable laws, regulations and codes,
including plumbing codes. Installation should
be performed by a qualied plumber.
Job Specication:
Grease and oils separator(s) shall be Thermaco Trapzilla hydromechanical grease/oil interceptor system(s) as
manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans.
Separator Specications:
Furnish and install ___ Thermaco Trapzilla Model No. TZ-600, linear low-density rotationally molded polyethylene
grease and oil separator(s) for below or above-ground installation, shall be ASME A112.14.3-rated at 75 GPM and
factory-rated at 150 gallons per minute peak ow, 600+ pounds of grease storage capacity with a at grease separation efciency curve, crush-resistant cylindrical walls, twin integral portals for access by grease pump truck for
grease removal, single separate integral portal for vacuum access for removal of solids, self guiding pipe for pump
truck access/solids removal, integral non-oatation anchor ring for in-ground installation, integral horizontal bafe,
laminar inlet ow diverter, integral vessel vent, separate storage compartments for grease and solids, and including
as an integral part of the unit an integral gas trap and a fully removable polyethylene self-positioning keyed cover
equipped with sealed thread fasteners.
©2008 Thermaco, Inc. • All rights reserved • Patented/Patents Pending • Specications subject to change without notice
8/08
Thermaco, Inc. • PO Box 2548 • Asheboro, NC 27204-2548 • Phone: (336) 629-4651 • Online: www.big-dipper.com
2
Loading...