The House of Marley EMDA001RG User Manual

One Foundation Digital Audio System

Product Name: Bluetooth Speaker
Model: EM-DA001-RG

Welcome to the House of Marley

We are honored you have selected One Foundation to become part of your music
experience. The One Foundation is a two-way, stereo sound system which works
with Bluetooth® devices connected wirelessly and hundreds of other devices via
the auxiliary, digital, or analog inputs. One Foundation fuses striking aesthetics with
a powerful audio engine and brings realism and detail to your music collection.
High-definition, long-throw, wood-fiber impregnated, 5.25-inch woofers in a tuned,
bass-reflex enclosure, Danish designed 1-inch tweeters and over 200 watts come
together in this beautifully engineered work of sonic beauty.

Everything You Need
One Foundation comes with the following items:

• Sound System [Ill. 1]

• Remote [Ill. 2]

• Power Cord for Wall Outlet [Ill. 3]

• 3.5mm Stereo Cable [Ill. 4]

Powering One Foundation

Your One Foundation uses a built-in, 100-120 VAC 50/60Hz or 220-240 VAC
50/60Hz 200W (depending on the country where the product was purchased)
power supply and is powered by a standard wall outlet.

1. Insert the AC power cord into One Foundation. [Ill. 5]

2. Insert wall plug into an appropriate wall outlet. [Ill. 6]

Inputs/Output
One Foundation uses automatic signal detection and will only access the inputs from
devices that are plugged into the audio system. One Foundation will automatically
revert to the last used input when powered “On”.
[ILLUSTRATION OF REAR INPUT PANEL – Ill. 7]

- [WHITE CIRCLE] RCA Analog Input: For use with analog sources.

- Pre-Out: Recommended for use with active subwoofer (not included). See

Fig. # for using One Foundation with a subwoofer.

- [RED CIRCLE] Digital Audio (Optical) Input: Recommended for use with

digital peripherals. Peripheral must be connected and turned on in order to
cycle to this input.

- [BLUE CIRCLE] Bluetooth Pairing Button: This mode can also be initiated by

pressing and holding the [INPUT] button on the remote.

[ILLUSTRATION OF SIDE PANEL]

- [GREEN] 3.5mm Auxiliary Input: This input will be triggered automatically

when a 3.5mm auxiliary cable (included) is plugged into One Foundation.

- USB-A Port: 2.1A Charging Port

Easy To Use

[ILLUSTRATION OF ROTARY DIAL – Ill. 8]
One Foundation uses one convenient control dial to operate power, volume, and
input selection.

- Press the control dial once to turn One Foundation on

- Press the control dial again while One Foundation is on to cycle through

active inputs

- Turn the control dial to adjust volume

- Press and hold the rotary dial to turn One Foundation off

Remote
[ILLUSTRATION OF REMOTE – Ill. 2]

- Input: Cycle through connected inputs or press and hold to engage Bluetooth

Pairing Mode.

- Power: On/Off

- FF: Press for next track, press and hold for fast forward

- RW: Press for previous track, press and hold for rewind

- Play/Pause: Play/Pause track

Connecting Your Device via Bluetooth®
Pairing Mode (Blinking Blue LED)

One Foundation automatically goes into Bluetooth Reconnect Mode for 10 seconds
as soon as you turn it on (fast flashing BLUE led). It then switches to Pairing Mode
(slow flashing BLUE led). You can pair a new device to One Foundation when in
Pairing Mode.

Note: Holding the [INPUT BUTTON] on the One Foundation remote for 3 seconds
will disconnect the device currently connected and go into Pairing Mode. Pairing
mode can also be engaged by disconnecting a connected device or by pressing the
[BT PAIR] on the back of One Foundation.

Connected Mode (Solid Blue LED)

Use your Bluetooth-enabled device to pair to One Foundation. One Foundation does
not require a pairing password. Once paired, the LED will glow solid blue.

Note: One Foundation will automatically pair with the last device connected to it
when turned ON (when the device is available).

Connecting other devices

The various inputs on the back of One Foundation allow you to connect other
devices to the system.