STANDARD AIR LIFT
INSTRUCTIONS
l
PARTS DRAWING
l
PARTS LIST
PN# 10740 -16749 -16600 - 10741
WARNING: READ INSTRUCTIONS BEFORE OPERATING
1. Center load on table - 1000 lb. maximum.
2. Connect to 110 psi maximum shop air.
3. Keep safety bar in position at all times - except
when lowering.
4. Keep hands and tools from under carriage.
5. Do not mount table when in elevated position.
6. Do not ride vehicle onto lift.
7. Lift must be in the lowered position when moving.
8. Only trained persons should operate Air Lift.
9.The working area should be sufficiently lit.
10. Foot controller should be at least 3 feet away from
Air Lift during raising and lowering operation.
11. Recommended for indoor use only.
401 South 2nd. Marshalltown, IA 50158 Ph: 855-752-5446 Fax 641-752-1205 www.handyindustries.com
HANDY DIVISION OF JADEIM, LLC
PART #
DESCRIPTION
14476
CV-17 CYCLE VISE – Vise with removable wheel stop built into vise
10728
12” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 48” includes stabilizer
bar
16011
13” FRONT EXTENSION – Extends lift top to 93” for longer wheel base motorcycles
10736
13” REAR EXTENSION – Extends lift top to 93” for longer wheel base motorcycles
15566
RAMP END EXTENSIONS – Attaches to end of lift ramp for a more gradual incline to
prevent bigger bikes from dragging bottom.
10737
SNOWMOBILE WING KIT – Used when lifting snowmobiles
16355
CE FOOT PEDAL – Covered foot pedal
10732
LIFT DOLLY – Helps move lift while in down position
16010
TOOL TRAY – Keeps tools organized and Handy
ST
NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS. DEATH, PERSONAL
INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.
ANDARD AIR LIFT
INSTRUCTIONS
UNPACKING AND SET-UP
1. Open carton, then remove ramp, and shipping boards.
AREFULLY TURN TABLE UPRIGHT INTO OPERATING POSTION BEFORE REMOVING SHIPPING
2. C
CABLE RESTRAINT FROM SCISSOR MECHANISM.
3. Connect foot-operated air valve to 110 psi air supply. The lift may be damaged and/or
personal injury may result if the pressure exceeds the maximum 110 psi rating.
4. Stand clear of lift table and depress the UP side of foot valve to raise table.
5.To lower table, lift detent bar from safety latch and lower to next position or to floor.
6. Mount ramp to lift top by inserting ramp tabs into slots on lift top.
TE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.
NO
OPERA
TION
1. Loads must be centered on table at all times.
2. Loads must be firmly positioned and secured on table at all times.
3. All moving parts have been lubricated at the factory and should be re-lubricated every 6
months to prevent galling. Grease zerks are located at each end of frame pivot shaft and at
top ends of inside frame assembly.
4. Lightly oil cylinder rod when it becomes dry.
5. Squirt some oil through air bleed hole in plate end of cylinder to lubricate piston and its
seal every 6 months.
6. Pivot shaft set screws should be checked frequently to be sure they are tight.These are
located at the top end of the inside frame assembly.
OTHER OPTIONS AVAILABLE
Separate installation instructions included with each option.
REPLACEMENT PARTS
Recommended maint
enance
1. Daily visual checks to be done.
A. Check all retaining rings, set screws and working parts are in place and in good working condition
before operations
B. Check cylinder and foot valves daily for any air leaks before operation.
2. Grease all grease zerks monthly. The locations of these are the two frame center pivot shafts and the
two cylinder pivot shaft under the lift top.
3. Oil cylinder every 3 months. Use a combination of 1 oz. of STP engine oil treatment and 2 oz. of air tool
oil mixed together and squirt into air cylinder air line. Unscrew foot valve from air line supply , squirt oil
into air line then screw foot valve back on air supply line and apply air pressure. This will blow air
inside of the cylinder coating the cylinder walls. This procedure keeps seals soft and pliable.
Limited Lifetime Warranty
Handy Industries, Division of Jadeim, LLC is providing a limited lifetime warranty on its motorcycle lift line. This Lifetime
Limited Warranty is available on lifts that have a serial number the same as or greater than those listed. Standard 1000 air
and electric #ST 0138, SAM 1000 air and electric #S 0082, SAM2 1000 air #S2 0020, BOB 1500 air #B 0100, Electric/Hydraulic
1500 #H 0008, Gruntavore 1800 #GR 0004. The purchaser must provide Handy with a legible copy of the purchase receipt
to obtain this warranty. The purchaser must provide Handy notice of the defect and establish that the equipment was properly set up, maintained and operated within the limits of rated and normal usage. Handy Industries, Division of Jadeim,
LLC reserves the right to have its product shipped back to the factory for inspection to ensure the lift was not being used
above its rated limits and capacity. The purchaser is responsible for freight charges until a determination is made by Handy.
Handy will reimburse the purchaser if it is determined that he or she was not using lift above the rated capacity. This warranty covers the structure of the following models of Handy lifts: Standard 1000, SAM 1000, SAM2 1000, BOB 1500,
Electric/Hydraulic 1500 and Gruntavore 1800. Attachments for these lift models are not included in the limited lifetime
warranty. This warranty only covers the structure of the lift itself. It does not cover any cost of labor, transportation, freight,
installation, misuse, abuse, or rust or failure of the air cylinder and/or foot pedal due to rust and or moisture. Also excluded in this warranty are items that were purchased for the Handy lift and installed on it at the factory such as electric motors,
hand-held pendants and bearings. Parts considered wearable carry a 90-day warranty. All other parts excluded from the
lifetime warranty carry a 1-year warranty from time of purchase. If the lift is purchased from a un-authorized distributor,
eBay or other online service, you are not eligible to receive the limited lifetime warranty for the structure of the lift. This
warranty is only offered to the original purchaser and is non-transferrable. It must be purchased from Handy Industries,
Division of Jadeim, LLC or one of its authorized distributors.
1/12 14382
STAND
ARD ELECTRIC LIFT
WITH PUSHBUTTON CONTROL
P/N 10742
INSTRUCTIONS
l
l
PARTS DRAWING
l
PARTS LIST
WARNING: READ INSTRUCTIONS BEFORE OPERATING
1.This is for the operation on a 115 volt, 60 Hz. circuit only.
2. Do not remove ground prong from plug.
3. Center load on table - 1000 lb. maximum.
4. Keep hands and tools from under carriage.
5. Do not mount table when in elevated position.
6. Do not ride vehicle onto lift.
7. Lift must be in the lowered position when moving.
8. Only trained persons should operate Electric Lift.
9.The working area should be sufficiently lit.
10. Recommended for indoor use only.
401 South 2nd. Marshalltown, IA 50158 Ph: 855-752-5446 Fax 641-752-1205 www.handyindustries.com
HANDY DIVISION OF JADEIM, LLC
STANDARD ELECTRIC LIFT
PART #
DESCRIPTION
14476
CV-17 CYCLE VISE – Vise with removable wheel stop built into vise
10728
12” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 48” includes stabilizer bar
16011
13” FRONT EXTENSION – Extends lift top to 93” for longer wheel base motorcycles
10736
13” REAR EXTENSION – Extends lift top to 93” for longer wheel base motorcycles
15566
RAMP END EXTENSIONS – Attaches to end of lift ramp for a more gradual incline to
prevent bigger bikes from dragging bottom.
10737
SNOWMOBILE WING KIT – Used when lifting snowmobiles
10732
LIFT DOLLY – Helps move lift while in down position
16010
TOOL TRAY – Keeps tools organized and Handy
NOTE: THIS SYMBOL MEANS WARING OR CAUSTION: DEATH, PERSONAL INJURY
AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED
CAREFULLY. READ ENTIRE
POWER SUPPLY
This lift is for operation on 115 volt, 60 Hz current only. Check outlet voltage before plugging in equipment.
WARNING: This lift is equipped with a 3-prong plug which must be plugged into a grounded
115 volt, 60 Hz power supply for your safety. Removing ground prong from plug or failure to plug
into a grounded receptacle may result in a fatal electric shock.
UNPACKING AND SET-UP
1. Open carton, then remove ramp and shipping boards.
2. Keeping hands free of lift mechanisms to avoid personal injury-CAREFULLY turn left over.
3. Mount ramp to lift top by inserting ramp tabs into slots on lift top.
NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.
OPERATION-LUBRIC
ATION
1. Loads must be centered on table at all times.
2. Loads must be firmly positioned on table at all times.
3. All moving parts have been lubricated at the factory and should be re-lubricated occasionally to pre
vent galling. Grease zerks are located at each end of frame pivot shaft and at top ends of inside frame
assembly.
4.The drive screw, motor and gear box were factory lubricated, and this lubrication should last for the life
of the lift. Should re-lubrication be necessary, use a No. 9 multi-purpose gear oil in gear box and an “O”
grade gear grease on drive screw.
5. Frame/motor pivot shaft set screws should be checked frequently to be sure they are tight.These are
located at the top of the inside frame.
INSTALLING
The drive train components have been burnished in to give a tight, well working fit and will be stiff for the
first few cycles. If drive screw should seize, put a few drops of oil on screw and reverse a few times. If
motor should pull down or hum,TURN OFF IMMEDIATELY. Check to see if drive screw is free.
Other Options
Available
Separate installation
instructions included
with each option
STANDARD ELECTRIC LIFT
ANDARD ELECTRIC LIFT
ST
Handy Industries, Division of Jadeim, LLC is providing a limited lifetime warranty on its motorcycle lift line. This Lifetime
Limited Warranty is available on lifts that have a serial number the same as or greater than those listed. Standard 1000 air
and electric #ST 0138, SAM 1000 air and electric #S 0082, SAM2 1000 air #S2 0020, BOB 1500 air #B 0100, Electric/Hydraulic
1500 #H 0008, Gruntavore 1800 #GR 0004. The purchaser must provide Handy with a legible copy of the purchase receipt
to obtain this warranty. The purchaser must provide Handy notice of the defect and establish that the equipment was properly set up, maintained and operated within the limits of rated and normal usage. Handy Industries, Division of Jadeim,
LLC reserves the right to have its product shipped back to the factory for inspection to ensure the lift was not being used
above its rated limits and capacity. The purchaser is responsible for freight charges until a determination is made by Handy.
Handy will reimburse the purchaser if it is determined that he or she was not using lift above the rated capacity. This warranty covers the structure of the following models of Handy lifts: Standard 1000, SAM 1000, SAM2 1000, BOB 1500,
Electric/Hydraulic 1500 and Gruntavore 1800. Attachments for these lift models are not included in the limited lifetime
warranty. This warranty only covers the structure of the lift itself. It does not cover any cost of labor, transportation, freight,
installation, misuse, abuse, or rust or failure of the air cylinder and/or foot pedal due to rust and or moisture. Also excluded in this warranty are items that were purchased for the Handy lift and installed on it at the factory such as electric motors,
hand-held pendants and bearings. Parts considered wearable carry a 90-day warranty. All other parts excluded from the
lifetime warranty carry a 1-year warranty from time of purchase. If the lift is purchased from a un-authorized distributor,
eBay or other online service, you are not eligible to receive the limited lifetime warranty for the structure of the lift. This
warranty is only offered to the original purchaser and is non-transferrable. It must be purchased from Handy Industries,
Division of Jadeim, LLC or one of its authorized distributors.
16486
Limited Lifetime Warranty
2-13
ANDARD ELECTRIC LIFT
ST
CONTROL SYSTEM
Loading...