The Genie a Division of Overhead Door ACSDA1 Users Manual

3

DEF

1

2

456

7

8

9

0

GHI

JKL

MNO

PQRS

TUV

WXYZ

9V

¤

This Wireless Keypad is compatible with all INTELLICODE® radio equipped GENIE® products.

1

23

456

7

8

9

0

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

PROG

OPERATING INSTRUCTIONS

(KEEP FOR FUTURE REFERENCE)

A Moving door can cause serious injury or death.

1 Keep people clear of opening while door is moving.
2DoNotallow children to play with Wireless Keypad.
3 During programming, the door opener could begin to run, so stay away from the

moving door and its parts. To keep the door from moving, close the door and
disconnect it from the Opener by pulling the Emergency Release.

FEATURES

• Ability to Control up to three

Genie® INTELLICODE® Openers

• Simple to Program and Install

• PIN Codes can be up to 8 Characters

• Low Battery Power Indicator

• Stays Programmed During

Battery Change

• Temporary PIN for Special Purpose Access

OOLS NEEDED:

T

• Drill with 1/16" Drill Bit

• Phillips Screwdriver

• Pencil

• Mounting Screws INCLUDED inside

Battery Compartment

WARNING

If Safety Reverse does not work properly:

1 Close door and disconnect the Opener using Emergency Release Cord.
2Do not use door Opener, Remote Controls, or Wireless Keypad.
3 Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

:

Interchangeable
Flip-up Cover
available in 3
optional Classic
Colors to match
your home’s
exterior decor

Red LED
indicates
Battery Power
and Status
during Use
and Programming

Instructions

3528135342

Program
Button

Backlit Keypad
for Ease of Use
at Night

Battery
Compartment
9 Volt Battery
(included)

SECTION

BASIC PROGRAMMING FOR

1

ONE

D

OOR OPENER

FOR CONVENIENCE

Program Keypad BEFORE mounting.

STEP

1:

A Activate programming mode.

• Press (in order) .

• Enter your PIN (3 to 8 characters).

• Press .

STEP 2:

A Find the Learn Code Button and Learn Code

Indicator LED on your door opener.

• Press the Learn Code Button.

• Enter your PIN and press on keypad.

• Press again.

STEP 3:

A To move the garage door:

• Enter your PIN.

• Press .

ETTING YOUR WIRELESS KEYPAD PIN

S

(PERSONAL IDENTIFICATION NUMBER)

–Red LED blinks - once per second.

–Red LED blinks - twice per second and turns off.

ROGRAMMING ONE DOOR OPENER

P

–If your door opener has a

black antenna wire,
the Learn Code Button
and Indicator LED
are located near the antenna.
(The light lens may need
to be opened.)

–If your door opener does not

have an antenna,
you have an external receiver.
The external receiver cover
must be removed to access
the Learn Code Button
and Indicator LED.

–

Learn Code Indicator LED (on Opener) will blink.

–Learn Code Indicator LED stays on.

–Learn Code Indicator LED turns off.

PERATING ONE DOOR OPENER

O

Red Indicator
LED

Located
on Opener
Housing

Learn
Code
Button

Proceed to Section 3 - Mounting Instructions.

NOTE

If the door does not move,check the red LED on Keypad.

•

If the LED is blinking rapidly,the PIN was entered
incorrectly. After the LED stops blinking, re-enter your
PIN and try again.

Any Keypad Button will control the door for 30 seconds

•

after the door starts moving.
Rapid blinking of the red LED indicates an error. After a

•

few seconds the LED will turn off. Start over.

For answers to questions, call 1-800-35 GENIE, or visit
www.geniecompany.com

Additional Genie® products can be ordered using the Accessories
page in your Owner’s Manual or through the 800 number above.

©2003 The Genie Company, D.B.A. GMI Holdings, Inc.

SECTION

2

PROGRAMMING FOR
2 OR 3 DOOR OPENERS

FOR CONVENIENCE

Program Keypad BEFORE mounting.

STEP 1:

A Activate programming mode.

STEP 2:

AAll door openers will use the same PIN.

STEP 3:

A Decide which door will be door #1,#2 and #3.

B Repeat step A above for each door opener.

STEP 4:

A To move one of the doors.

SEE NOTE AT BOTTOM OF SECTION 1
Proceed to Section 3 - Mounting Instructions.

SETTING YOUR WIRELESS KEYPAD PIN

(PERSONAL IDENTIFICATION NUMBER)

• Press (in order) .

–Red LED blinks - once per second.

• Enter your PIN (3 to 8 characters).

• Press .

–Red LED blinks - twice per second and turns off.

PROGRAMMING THE KEYPAD FOR
MULTIPLE DOOR OPENERS

• Enter your PIN and press .

– Red LED blinks - once per second.

• Press again.

–Red LED blinks - twice per second.

• Press the number of doors (total) you wish

to control ( or ).

• Press .

–Red LED blinks several times and turns off.

ROGRAMMING DOOR OPENERS

P

• Press the Learn Code Button (see Section 1 Step 2).

–Learn Code Indicator LED (on Opener) blinks.

• Enter your PIN and press .

–Learn Code Indicator LED stays on.

• Press the number you have picked for this

door Opener ( or or ).

–Learn Code Indicator LED stays on.

•

Press .

–Learn Code Indicator LED turns off.

Each door opener must be programmed to receive the
signal from the Wireless Keypad.

O

PERATING 2 OR 3 DOOR OPENERS

• Enter your PIN.

• Press .

• Press door opener number ( or or ).

SECTION

3

The Keypad must be mounted in sight of the door(s), at
least 5 feet above the ground and clear of any moving
door parts.

A Mount Keypad. (Mounting screws located inside

battery compartment.)

• Remove Battery Cover. See Section 4 Figure 2.

•

Drill a 1/16”pilot hole for the top mounting screw.

• Install a screw into the drilled
hole,leaving a 1/8" gap
between the screw head
and the wall. See Figure 1.

• Hook the Keypad over
the screw.

• Mark, drill pilot hole and
fasten bottom screw.

• Reinstall Battery Cover.

SECTION

4

F

ORGOT YOUR PIN

HANGING YOUR PIN

C

A Erase old PIN :

• Press and hold in order -

–Red LED will blink once and turn off.

• Release all buttons.

B Programming Door Opener(s).

• Return to “Programming”Section 1 or Section 2.

USING A TEMPORARY PIN

A temporary PIN allows temporary access to your home by
repair persons, meter readers, etc.

A

Enter your PIN

•

Press .

B

Enter the Temporary PIN (from 3 to 8 characters).

• Press .

MOUNTING INSTRUCTIONS

Figure 1

1"
8

Wall

screw head gap

BASIC
ADDITIONAL OPERATIONS

OR

.

NOTE

•

DO NOT reprogram the Door Opener(s).

•

Te mporary PIN remains active until the next time your
normal PIN is entered.

CHANGING BAT TERY

If the red LED does
not blink during use,
the battery needs to
be changed.

Covers available in:

• Almond

(P/N 00000)

• Sandstone

(P/N 00000)

• Brown
(P/N 00000)

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS 210 of Industry Canada.This equipment has been tested and
found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on,the user is
encouraged to try to correct the interference by one or more of the following measures: 1.Re-orient or
relocate the receiver antenna. 2. Increase the separation between the opener and receiver. 3.Connect the
opener into an outlet on a circuit different fromthat to which the appliance isconnected. 4.Consult the dealer.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.

Figure 2

Red LED

9V

Battery

Bottom
Mounting
Screw

Press here

Printed in the U.S.A.