PA 10 ECO
High-Performance 240-Watt PA Speaker with 10" Woofer
and Dual Electro-Dynamic Driver
Users manual
DATA-MANFULL_PA10_ECO_ENG_Rev_A.PMD 20.02.2006, 14:531
2
PA 10 ECO
SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this device near water.
6) Clean only with a dry cloth.
7) Be sure to mount your speakers on a solid, stable and level base or stand. Vibrating
floors do not provide reliable support for speaker enclosures or stacks.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Only use attachments/accessories specified by the manufacturer.
10) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the device. When a cart is used, use caution when moving the cart/device
combination to avoid injury from stumbling over it.
11) Refer all servicing to qualified service personnel. Servicing is required when the unit
has been damaged in any way, liquid has been spilled or objects have fallen into the device,
the unit has been exposed to rain or moisture, does not operate normally, or has been
dropped.
12) Do not block any ventilation openings. Install in accordance with the manufacturers
instructions.
DATA-MANFULL_PA10_ECO_ENG_Rev_A.PMD 20.02.2006, 14:532
3
PA 10 ECO
1. CONNECTIONS
Connections
Two ¼ loudspeaker inputs are wired in parallel. You can alternatively connect one of the
connectors to the output on your power amp and tap into the signal from the amp once
again on the second connector, in order to feed this signal into an additional loudspeaker.
¼" TS connector
+ ATTENTION: Never connect more than one power amp output to the
loudspeaker system. This may permanently damage your setup.
DATA-MANFULL_PA10_ECO_ENG_Rev_A.PMD 20.02.2006, 14:533
4
PA 10 ECO
2. POWER AMP RATING
The power rating of your amp should be roughly twice the speaker load capacity.
ATTENTION!
+ When several loudspeakers are wired in parallel the overall impedance
Z
ges
to be handled by the power amp can be calculated, as shown below,
from the individual impedance values of the connected speakers:
Your amplifier may be damaged if the actual impedance drops below its
input impedance. Please make sure that the calculated total impedance
Z
ges
is not smaller than the minimum impedance specified for your amplifier.
3. WIRING
In the following example, the main output signal of a mixing console is connected to a power
amplifier. Both the outputs and inputs are stereo. A PA 10 ECO box is connected to each of
the amp outputs, and these speakers reproduce the entire frequency range (full range).
Full-range stereo operation
DATA-MANFULL_PA10_ECO_ENG_Rev_A.PMD 20.02.2006, 14:534
5
PA 10 ECO
4. SPECIFICATIONS
6<67(0'$7$ 3$(&2
Type 2-way full-range speaker
Frequency response 60 Hz - 20 kHz
Power rating (Peak program) 240 W
Impedance
8
:
Sound pressure level (1 W @ 1 m) 98 dB (Full Space)
Dispersion 90° x 40°
Crossover frequency 3.5 kHz
Rigging/fittings
2x ergonomically shaped handle
1x integral tripod and stand adaptor
&20321(176
HF driver Dual electro-dynamic drivers
Woofer 10" (259 mm)
',0(16,216:(,*+7
(W x H x D)
ca. 12.2 / 6.7" x 19.3" x 11.1"
(311 / 170 mm x 490 mm x 282 mm)
Weight approx. 19.8 lbs. (9.0 kg)
Shipping weight approx. 22.5 lbs. (10.2 k g)
THOMANN MUSIKHAUS is constantly striving to maintain the highest professional standards. As a
result of these efforts, modifications may be made from time to time to existing products without prior
notice. Specifications and appearance may differ from those listed or illustrated.
DATA-MANFULL_PA10_ECO_ENG_Rev_A.PMD 20.02.2006, 14:535
Loading...