Theater Solutions TS6, TS8 Instruction Manual
Congratulations on the purchase of your Theater Solutions TS8 (TS4、TS6) loudspeaker
switcher.
When used with your current audio/home-theatre system, the TS8 (TS4、TS6) will allow you
to add up to 8 pairs of loudspeakers, while providing protection for your amplifier/receiver.
The TS8 (TS4、TS6) was manufactured with high quality components and engineered to
provide you with many years of trouble free listening enjoyment.
Though easy to install, we recommend that you read carefully through this instruction
manual and save your bill of sale in the unlikely event that your loudspeaker switcher
requires servicing.
Adding additional loudspeakers around your home is now simple, thanks to the Theater
Solutions loudspeaker selector. The TS8 (TS4、TS6) has been designed to let you turn on or
off any combination of up to 8 pairs of loudspeakers without purchasing additional amplifiers.
4 1
4、6、8-Way Protected Loudspeaker
Switcher Instruction Manual
Safety Instructions
TS4、TS6、TS8
Theater Solutions
Theater Solutions
www.theater-solutions.net
sales@theater-solutions.net
• We recommend that the amplifier/receiver be
turned OFF while making any connections.
• Do not use wherever there is a risk that the
switcher may come into contact with water or
excessive moisture, such as near pools, bathtubs
and wet basements.
• In the event of a malfunction, do not attempt to
service the product yourself. Please contact
Theater Solutions.
32
Installation
Make sure power to your receiver or power
amplifier is off before doing any wiring.
To make a connection, strip 3/8" of insulation from the end of the wire.
Twist the wire ends so that there are no frayed wires.
Push the tab and insert the wire into the correct input.
Connect wires from each of the loudspeakers to the corresponding output connection on the switcher.
Insert Wire
Push Tab
L INPUTS R
Operation
Initial connection
For initial turn-on, it is recommended that only one loudspeaker pair be used. Select this loudspeaker pair and turn on your
receiver/amplifier. Ensure that sound is coming from both loudspeakers. If there is no sound, check your connections from your amplifier/receiver and the loudspeaker connections.
Loudspeaker Selector Inputs
Engaging additional front panel controls (1-4 or 6 or 8) will allow the selected loudspeakers to function.
Single Pair Direct
When listening to a single pair of loudspeakers, especially at high listening levels, it is recommended that the Single Pair Direct
be turned ON.
Troubleshooting
Solution
Make sure the correct loudspeaker is selected
Make sure no wires are touching each other or the case of the amplifier or the
switcher
Normal – This is due to the additional resistance added to protect your amplifier
Reduce volume level
Turn unused loudspeakers off
If only one loudspeaker pair is used, turn the Single Pair Direct On.
Problem
No sound
Slight drop in volume when
PROTECTION is selected
Unit gets very hot
TS8 Technical specifications
Controls
1
Loudspeaker selectors 1 through 8 ( or 4 or 6) – Press the
button in to listen to the desired loudspeakers.
2
Single Pair Direct Switch – Impedance protection switch for the
amplifier/receiver. Use as directed in this owners manual.
1
2
Front Panel
3
Connection from amplifier – from the L(left) and R(right)
loudspeaker output of your receiver or amplifier.
4
Loudpeaker Connections – connections to be made from the
TS8 (TS4、TS6) to the desired loudspeakers, with the
corresponding selector on the front panel.
Rear Panel
3
4
Typical Hook Up
The diagram below shows an overview of a typical system using 8 ( or 4 or 6 ) loudspeaker pairs.
Overview of typical system
Installation Tips
18 or 16 gauge stranded loudspeaker wire is recommended. 14 gauge is recommended for runs longer than 50 feet.
You can mix any combination of 4, 6, 8 and 16 ohm loudspeakers
Wire according to local laws. Specific "CL" fire rating may be required according to your local building codes. Your dealer
may know more about obtaining such wire.
Avoid running close to AC power wiring for safety and to avoid the possibility of picking up any noise.
Connect to receiver/amplifier R/L
loudspeaker output
Loudspeaker OFF
Loudspeaker ON
Amplifier
Single Pair
OFF
Single Pair
Engaged
SPEAKER 1(8Ohms)
Right
Left
Outputs: 8 loudspeaker pairs, 4 to 16 ohm impedance
Wire Gauge: 14 to 22 gauge
Size (WDH): 17"×47/8"×23/16"
Weight:4.15 lbs
Supplied accessories:
• User manual (this document)
• Sheet of front panel labels
TS4 Technical specifications
Outputs: 4 loudspeaker pairs, 4 to 16 ohm impedance
Wire Gauge: 14 to 22 gauge
Size (WDH): 81/2"×47/8"×23/16"
Weight:2.35 lbs
Supplied accessories:
• User manual (this document)
• Sheet of front panel labels.
TS6 Technical specifications
Outputs: 6 loudspeaker pairs, 4 to 16 ohm impedance
Wire Gauge: 14 to 22 gauge
Size (WDH): 17"×47/8"×23/16"
Weight:4.15 lbs
Supplied accessories:
• User manual (this document)
• Sheet of front panel labels.
Connect the wires from the loudspeaker output of your receiver or amplifier to the terminals marked INPUTS on the TS8 (TS4、TS6).
Connect the "+" output from the right front output on the amplifier to the right "+" on the TS8 (TS4、TS6) and connect the "-" output from
your amplifier to the "-" input of the switcher. Likewise, connect the left channel wires to the left inputs. Ensure that the connections are
made correctly, as any improper connections will cause the loudspeakers to play out of phase.
Design and specifications are subject to change without notice.
Loading...