800, 900 and 1000 Base and Corner Base Unit Assembly
Note: If fitting a “True Handleless” kitchen, some
TH
components will differ to those shown in this
instruction and will also be packaged separately.
Please refer to your True Handleless guide to
Receiving for further details on the different
components and difference in installation.
Components
A
D
G
C
B
E
A
F
Important Information - True Handleless Kitchens Installers: See Note Above
Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area.
Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen booklet for further information.
Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface.
In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted.
These units may be fitted with a drawer system. The drawers are supplied separately. These instructions show the runner positions for the drawer system.
Follow the instructions supplied with the drawers for drawerbox assembly.
Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department.
Note - Fitting Handles: (1) Decide where you are going to position each handle to maintain symmetry around your kitchen. (2) Measure the handle centres and mark off each door/drawer position. (3) Drill through the door/drawer
using a fine drill (<2.5mm), then drill back from the rear face using a 4.5mm drill. (4) Attach with the fixings provided with your handle.
Ref. No. Item Quantity Ref. No. Item Quantity Ref. No. Item Quantity
150101
150202 16
150201 16/20
150199 4
150198
154082 6
3.5x12mm
4x12mm
4x15mm
4.5x45mm
55mm Carcase Screw
14
154068 8
154047 2
3
152181 4
6154027
152401 4/5
152418 4/5
152402 2
152148 4
Tools Required
5mm
Drill
Medium Crosshead
Screwdriver
G-Clamp
(pair)
Hammer
TH
FM 665131
154084 1
154085 7
154004
152162 4
150308 2
150309 2
8
151999
151500 2
12
Large Flathead
Screwdriver
Spirit Level Bradawl
Tape Measure
1 2
1
3
333
3
4
3
3
11
45mm
12
13
125mm
9
Assembly Instructions
3 4
Modification required at this stage, see True
TH
1 2
98mm
Drawer runner
Handleless guide for further details.
A
1 2 1 2
Drawer runner
A
98mm
Note: Drill centre holes of B
12
B
4
Scrap wood
3
154085
6
E
and E for Base Units. For
Corner Base Units consult
kitchen plan for door size and
drill accordingly.
Scrap wood
5mm
4
5 6
1212
5
A
Drawer Runner
Front
x4
1
154082 6
7
11
1 x 'L'; 1 x 'R'
3.5 x 16mm
Fit as third screw
5
5
5
x2
E
B
5
5
6
2
Do Not Over Tighten
A
2
154004
45mm
10
9
125mm
6
5
1312
Without Drawers
Modification required at this
stage, see True Handleless
TH
guide for further details.
Start
Locked
Scrap wood
11
8
8
8
D
7
9
8
10
12
13
F
12
13
9
Modification required at this
stage, see True Handleless
TH
8
150101
2
8
guide for further details.
150199
4
150202
2
12
Note: Countersunk screw
goes into back panel D.
154068
2
154004
2
10
Note: Only drill if drawers are
150202
154047
4
10
2
being fit. Base Units drill as
indicated. Corner Base Units
consult kitchen plan for door
size and drill accordingly.
Only drill from the lower set
of holes
5mm
13
150198
2
1514
14
15
18
19
20
82mm
21
With Drawers
14
G
15
1716
With Drawers
Drawer runner
14
154085
F
15
1
2018 2221
With Drawers
154084 1
19
18
154004
2
Drawer Runner
Front
x4
1716
21
21
Do Not Over Tighten
Locked
Start
21
21
21
21
4/800 & 900
152401
1 x 'L'; 1 x 'R'
3.5 x 16mm
Fit as third screw
5/1000
150201
x2
16/800 & 900
20/1000
150198
18
20
18
19
20
19
150198
2
22
21
1
22
22
22
22
140mm
22
152418
4/800 & 900
5/1000
2523
Installation Instructions
23
150202 154068
24
150308 150309
2
2
23
24
2
Modification required at this
stage, see True Handleless
TH
guide for further details.
5mm
2
25
23
24
25
23
24
25
25
Appropriate to wall type
(Not supplied)
2
26
33
C
A
33
B
33
32
55mm
52mm
15mm
Softclose ON
Softclose OFF
40
15mm
2926 30 31
151500
27
152402
150101
28
28
2
30
Note: Do not over tighten screws
or use a power screwdriver.
31
C
26
28
28
28
31
26
27
26
2
28
28
29
4
28
31
27
27
27
31
31
31
154027
32 35
6
=
=
36
150101
37
Fixed Fascia Fitting
8
34
36
151999
32
33
C
A
33
B
33
34
34
32
34
34
35
4
36
150202
16mm
71.5mm
36
2/4
37
71.5mm
36
16mm
37
37
37
36
38
Corner Post Fitting
52mm 55mm
15mm
38 38
38 38
Note: Fittings are packed
with the Corner Post.
38
38
35
154068
34
152148 4
151999
37
150202
39
TH
41
Corner Post Fitting
Modification required at this
stage, see True Handleless
guide for further details.
Note: Fit corner post to adjacent unit, then fit optional
blanking panel to corner base unit, finally attached corner
post to corner base unit mullion. Use appropriate number
of screws (not supplied). Any excess/hangover does not
need to be trimmed as it will be concealed in the void.
40
40
40
40
41
41
39
41
41
39
2/4
2/4
4/8
37
74mm
40
39
40
Not Supplied
Unit Size X
Total Length on Plan
6-10
625mm
39
150124
41
6
Door Size
38 38
Modification required at this
stage, see True Handleless
TH
guide for further details.
38
150124 154081
12
41
41
39
40
6
40
40
40
41
Unit Size (mm) Required Door Size (mm) Total Length in Plan (mm) Void "x" (mm)
800mm 300 925 125
800mm 400 1025 225
800mm 500 1125 325
1000mm 400 1025 25
1000mm 500 1125 125
1000mm 600 1225 225
Ref. 170801 (05)
Loading...