Page 1
www.t-fal.com
BREAD MAKER
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page1
Page 2
1
2
3
4
2b2a
2c
2d
2
5
7
6
6a
6b
2g
2e
2f
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page2
Page 3
3
A
D E F
G H I
J K L
B C
2c
2d
2e
2f
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page3
Page 4
IMPORTANT
SAFEGUARDS
When using electrical appliances, basic safety
precautions should always be followed including
the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or
knobs.
3. To protect against electrical shock do not
immerse cord, plugs, or this appliance in
water or other liquid.
4. Not intended for use by children. Close
supervision is necessary for any appliance
being used near children.
5. Unplug from outlet when not in use and
before cleaning. Allow to cool before
putting on or taking off parts.
6. Do not operate any appliance with a
damaged cord or plug or after the appliance
malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service facility for examination,
repair or adjustment.
7. The use of accessory attachments not
recommended by the appliance manufacturer
may cause injuries.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or
counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric
burner, or in a heated oven.
11. Extreme caution must be used when moving
an appliance containing hot oil or other hot
liquids.
12. Plug cord into the wall outlet. To disconnect,
press and hold the START /STOP button for
a second, remove plug from wall outlet.
13. D o not use applia nce for other th an
intended use.
SAVE THESE
INSTRUCTIONS
1. For your safety, this appliance complies with
applicable technical rules and norms.
2. Check that the main voltage corresponds to
the voltage indicated on the appliance.
3. Use a stable work surface, away from any
contact with water and never in a built-in
kitchen alcove.
4. Do not move the appliance when working.
Polarization instructions
This appliance has a polarized plug (one blade
is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit into a
polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
Do not attempt to modify the plug in any way.
Short Cord instructions
1. A short power cord is to be provided to reduce
the risk resulting from becoming entangled
in or tripping over a longer cord.
2. Longer power cords or extension cords are
available and may be used if care is exercised
in their use.
3. If a long power cord or extension cord is
used,
a) The marked electrical rating of the cord or
extension cord should be at least as great
as the electrical rating of the appliance,
and
b) The cord should be arranged so that it will
not hang over the countertop or tabletop
where it can be pulled on by children or
tripped over unintentionally.
4
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page4
Page 5
5
FOR HOUSEHOLD USE ONLY
DO
• All interventions other than cleaning and
everyday maintenance by the customer must
be performed by an authorized service center.
• For your safety, only use accessories and spare
parts designed for your appliance.
• All appliances undergo strict quality control.
Practical usage tests are performed on
randomly selected appliances, which would
explain any slight traces of use.
• At the end of the program, always use oven
gloves to handle the bread pan or hot parts
of the appliance. The appliance becomes very
hot during use.
• Never obstruct the air vents.
• Be very careful, steam can be released when
you open the lid at the end of or during the
program.
• When using program No.9 (jam, stewed
fruit, etc.) watch out for steamand hot
spattering when opening the lid.
• Caution, if the dough overflows and touches
the heating element, it can catch fire, therefore:
- Never exceed the quantities indicated in the
recipes.
- Never exceed 2lbs of dough.
- Never exceed 2 cups of flour and 1 teaspoon
of yeast.
• Disconnect the appliance if it shows any working abnormalities.
DO NOT
• Do not use an external timer or separate
remote control system.
• Do not touch the metal parts or hot surfaces
of the appliance when it is working.
• Do not use this appliance as source of heating
or drying.
• Do not unplug appliance by pulling on cord.
Instead grasp plug and pull to disconnect.
• Do not touch the viewing window during
and just after operation. The window can
reach a high temperature.
• Do not place the appliance on other
appliances.
• Do not place paper, cardboard or plastic in or
on the appliance.
• Should any part of the appliance catch fire,
do not attempt to extinguish it with water.
Unplug the appliance. Smother flames with a
damp cloth.
• This product has been designed for household
use only. Any professional use, inappropriate
use or failure to comply with the instructions
will void the warranty.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page5
Page 6
• Ful
a g
• A s
the
• Rem
and
wis
• Put
ord
die
• Pla
hol
the
sha
sid
wil
Practical advice
Preparation
1 Please read these instructions carefully: the
method for making bread with this appliance
is not the same as for hand-made bread.
2 All ingredients used must be at room temper-
ature (unless otherwise indicated) and must
be measured exactly. Measure liquids with
the graduated beaker supplied. Use the
double measuring spoon supplied to
measure teaspoons on one side and tablespoons on the other. All spoon measures
are level and not heaped. Incorrect meas-
urements give bad results.
3 For successful bread making using the correct
ingredients is critical. Use ingredients before
their use-by date and keep them in a cool, dry
place.
4 It is important to measure the quantity of
flour precisely. That is why you should measure your flour by spooning it into the measuring cup and then leveling it off with a knife.
Use packets or a jar of dried yeast unless oth-
erwise indicated in the recipe. Baking powder
is not a substitute for yeast. Once a packet of
yeast has been opened, it should be sealed,
stored in a cool place and used within 48
hours.
5 To avoid spoiling the proofing of the dough,
we advise that all ingredients should be put in
the bread pan at the start and that you
should avoid opening the lid during use (unless otherwise indicated). Carefully follow the
order of ingredients and quantities indicated
in the recipes. First the liquids, then the solids.
Yeast should not come into contact with
liquids, sugar or salt.
General order to be followed:
> Liquids (butter, oil, eggs, water, milk)
> Salt
> Sugar
> Flour, first half
> Powdered milk
> Specific solid ingredients
> Flour, second half
> Yeast
Using
• Bread preparation is very sensitive to temperature and humidity conditions. In case
of high heat, use liquids that are cooler than
usual. Likewise, if it is cold, it may be necessary
to warm up the water or milk (never exceeding 95°F).
• It can also sometimes be useful to check
the state of the dough during the second
kneading: it should form an even ball which
comes away easily from the walls of the pan.
- If not all of the flour has been blended into
the dough, add a little more water,
6
Description
1 - lid with window
2 - control panel
a - display screen
b - on/off button
c - weight selection
d - buttons for setting delayed start
and adjusting the time for programs 8, 12
e - select crust color
f - choice of programs
g - operating indicator light
3 - bread pan
4 - kneading paddle
5 - graduated beaker
6 - a - tablespoon measure
b - teaspoon measure
7 - hook accessory for lifting out
kneading paddles
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page6
Page 7
Before you use your appliance for the first time
• Remove the accessories and any stickers either
inside or on the outside of the appliance - A.
• Clean all of the parts and the appliance itself
using a damp cloth.
Quick-start
• Fully unwind the power cord and plug it into
a grounded socket.
• A slight odor may be given off when used for
the first time.
• Remove the bread pan by lifting the handle
and turning the bread pan slightly anti-clockwise. Then insert the kneading paddle -B-C.
• Put the ingredients in the pan in exactly the
order recommended. Make sure that all ingredients are measured with precision -D-E.
• Place the bread pan in the breadmaker. By
holding the bread pan by handles, insert it in
the breadmaker so that it fits over the drive
shaft (you will need to tilt it slightly to one
side to do this). Turn it gently clockwise and it
will lock into place -F-G.
• Close the lid. After you hear the beep, program
1 will appear on the display as the default setting, i.e. 2 lbs, medium browning -H.
• Press the button. The timer colon flashes.
The operating indicator lights up -I-J.
• Unplug the breadmaker at the end of the
cooking or warming cycle. Lift the bread pan
out of the breadmaker. Always use oven
gloves as the pan handle is hot, as is the inside
of the lid. Turn out the hot bread and place it
on a rack for at least 1 hour to cool -K.
To get to know your breadmaker, we suggest trying the BASIC WHITE BREAD recipe for
your first loaf (refer to the recipe section).
- if the dough is too wet and sticks to the
sides, you may need to add a little flour.
Such corrections should be undertaken very
gradually (no more than 1 tablespoon at a
time) and wait to see if there is an improvement before continuing.
• A common error is to think that adding
more yeast will make the bread rise more.
Too much yeast makes the structure of the
bread more fragile and it will rise a lot and
then fall while baking. You can determine the
state of the dough just before baking by
touching it lightly with your fingertips: the
dough should be slightly resistant and the fingerprint should disappear little by little.
7
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page7
Page 8
6. Ultra Fast I. The Ultra Fast I program is
only for 2 lbs loaves. Bread made using Ultra
Fast programs is more compact than that
made with the other programs.
7. Ultra Fast II. The Ultra Fast II program is
only for 1.5 lbs loaves. Bread made using
Ultra Fast programs is more compact than
that made with the other programs.
8. Bread Dough. The Bread Dough program
does not bake. It is a kneading and rising
program for all leavened doughs such as
pizza dough, rolls, sweet buns.
9. Jam. The Jam program automatically cooks
jams and compots (stewed fruits) in the
pan.
10. Cake. Can be used to make pastries and
cakes with baking powder.
11. Sandwich loaf. The Sandwich Loaf pro-
gram is ideal for soft, thin-crusted bread.
12. Loaf Cooking. The Loaf cooking program
allows you to bake for 10 to 60 minutes
(baking time can be set at 1 minute intervals). It can be selected alone and used:
a) with the Bread Dough program,
b) to reheat cooked and cooled breads
or to make them crusty,
c) to finish cooking in case of a prolonged
electricity cut during a bread baking
cycle.
The breadmaker should not be left unattended when using program 12.
To interrupt the cycle before it is finished,
the program can be stopped manually by
holding down the button.
Using your breadmaker
Selecting a program
Choosing a program triggers a series of steps
which are carried out automatically one after
another.
The menu button enables you to
choose a certain number of different
programs. The time corresponding to
the program is displayed. Every time you press
the button, the number on the display panel
switches to the next program from 1 - 12:
1. Basic White Bread. The Basic White Bread
program is used to make most bread
recipes using white flour.
2. French Bread. The French Bread program
corresponds to a traditional French crusty
white bread recipe.
3. Whole wheat Bread. Whole wheat Bread
Program is used to make whole wheat
bread using whole wheat flour.
4. Gluten Free Bread. This is recommended
for people with celiac disease, making them
intolerant of the presence of gluten in many
flours and grains (wheat, rye, barley, oats,
etc.). The pan and paddles must always be
thoroughly cleaned to avoid any risk of contamination with other flours. In the case of
a strictly gluten-free diet, take care that the
yeast used is also gluten-free. The consistency of gluten-free flours does not yield an
ideal dough. The dough sticks to the sides
and must be scraped down with a flexible
plastic spatula during kneading. Gluten-free
bread will be of a denser consistency and
paler than normal bread.
5. Sweet Bread. The Sweet Bread program is
for recipes containing more sugar and fat
such as brioches and milk breads. If you are
using special flour blends for brioche or rolls,
do not exceed 1.5 lbs of dough in total.
8
A default setting is displayed for each program. You will therefore have to select the desired
settings manually.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page8
Page 9
Selecting the weight
of the bread
The bread weight is set by default at 2 lbs. This
weight is shown for informational purposes. See
the recipes for more details. Programs 4, 6, 7, 8,
9, 10, 12 do not have weight settings. Press the
button to set the chosen weight – 1.5 lbs or
2 lbs. The indicator light against the selected
setting comes on.
Selecting the crust color
By default, the color of the crust is set at
MEDIUM. Programs 8, 9 do not have a color setting. Three choices are possible: Light /
Medium/ Dark.
If you want to change the default setting, press
the button
Start / Stop
Press the button to switch the appliance on.
The countdown begins. To stop the program or
to cancel delayed programming, hold down on
the button for 3 seconds.
Cycles
Kneading
For forming the dough’s structure so that it
can rise better.
During this cycle, the dough is in the 1st or 2nd
kneading cycle or in a stirring period between
rising cycles.
During this cycle, and for programs 1, 2, 3, 4, 5,
6, 7, 10, 11, you can add ingredients: dried fruit
or nuts, olives, etc. A beep indicates when you
can add extra ingredients. See the summary
table for baking times (pages 20-21) and the
“extra” column. This column indicates the time
that will be displayed on your appliance’s
screen, and a beep will also signal the machine
has gone into another stage.
Rest
Allows the dough to rest to improve kneading quality.
Rising
Time during which the yeast works to let
the bread rise and to develop its aroma.
The dough is in the 1st, 2nd or 3rd rising cycle.
Baking
Transforms the dough into bread and gives
it a golden, crusty crust.
The bread is in the final baking cycle.
Warming
Keeps the bread warm after baking. It is recommended that the bread should be turned
out promptly after baking, however.
For programs 1, 2, 3, 4, 5, 6, 7, 10, 11, 12, you
can leave your preparation in the appliance. A
one-hour warming cycle automatically follows
baking. During the hour for which the bread is
kept warm, the display shows 0:00 and the dots
on the timer flash.
At the end of the cycle, the appliance stops automatically after several sound signals.
9
A table (pages 20-21) indicates the breakdown of the various cycles for the program
chosen.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page9
Page 10
Flou
• For
“flo
pos
wh
ma
the
• Wh
ma
a d
• De
res
tigh
air,
• Ne
me
• Ne
sin
less
• Alw
urin
• Mo
• Ne
Yeas
• Yea
use
yea
yea
• The
alw
for
yea
• Old
as
• All
be
tai
free
Practical advice
If there is a power loss: if, during the cycle, the
program is interrupted by a power cut or mishandling, the machine has a 10-min protection
time during which the settings are saved.
The cycle starts again where it stopped. Beyond
that time, the settings are lost.
If you plan to run a second program, open
the lid and wait 1 hour before beginning the
second preparation.
To turn out your loaf of bread: it may happen
that the kneading paddle remain stuck in the
loaf when it is turned out. In this case, use the
hook accessory as follows:
> once the loaf is turned out, lay it on its side
while still hot and hold it down with one hand,
wearing an oven glove,
> with the other hand, insert the hook in the axis
of the kneading paddle - M,
> pull gently to release the kneading paddle - M,
> turn the loaf upright and stand on a grid to
cool.
Delayed start program
This step comes after selecting the program,
browning level and weight. The program time is
displayed. Calculate the time difference between the moment when you start the program
and the time at which you want your preparation to be ready. The machine automatically includes the duration of the program cycles.
Using the and buttons, display the calculated time ( up and down). Short presses
change the time by intervals of 10 min + a short
beep. Holding the button down gives continuous scrolling of 10-min intervals.
For example, it is 8 pm and you want your bread
to be ready for 7 am the next morning.
Program 11:00 using the and .
Press the button. A beep is emitted. The
timer colon blinks. The countdown begins.
The operating indicator light comes on.
If you make a mistake or want to change the
time setting, hold down the button until it
makes a beep. The default time is displayed.
Start the operation again.
With the delayed start program do not use
recipes which contain fresh milk, eggs, soured
cream, yogurt, cheese or fresh fruit as they
could spoil or stale overnight.
M
10
You can program the appliance up to start 15 hours in advance to have your preparation
ready at the time you want. This function cannot be used on programs 6, 7, 9, 12.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page10
Page 11
Essential bread making ingredients
Flour:
• For best results always use “bread flour” or
“flour for bread machines” rather than allpurpose flour when making breads that use
white flour as they are specially adapted for
making bread, unless otherwise specified in
the recipe.
• Whole wheat or whole grain flours and blends
make for heavier dough that rises less and has
a denser texture.
• Depending on the quality of the flour, baking
results may also vary. Always store flour in airtight containers as it reacts to humidity in the
air, absorbing moisture or losing it.
• Never sift flour when making bread and
measure carefully.
• Never scoop flour directly from the canister
since air pockets can form and you will have
less flour than called for in the recipe.
• Always spoon flour into the correct-size measuring cup a spoonful at a time.
• Mound flour and level it off with a knife.
• Never pack down flour.
Yeast:
• Yeast is what makes the dough rise.You can
use any of the following yeasts: active dry
yeast, quick-rise yeast or bread machine
yeast.
• The quality of yeast can vary, and it does not
always rise the same way. Bread can therefore come out differently depending on the
yeast used.
• Old or poorly stored yeast will not work as well
as a freshly opened packet of dry yeast.
• All opened, unused packages of yeast should
be closed tightly or stored in an air-proof container or plastic bag in the refrigerator or
freezer.
• Yeast does not have to be at room temperature.
• Always check the yeast packet expiration date
and discard any expired yeast.
• The recipe proportions indicated are for dried
yeast. If you use fresh yeast, multiply the
quantity by 3 (in weight) and dilute the yeast
in a small amount of warm water with a little
sugar for more effective results.
Water:
• Water, as do all liquids, rehydrates and activates the yeast. It also helps the gluten, a natural protein found in wheat and other grains,
to develop when dough is kneaded. The
gluten is what gives bread its chewy texture.
• Chemically treated water high in chlorine or
fluoride, or very hard or soft water, can adversely affect the yeast.
• Chemicals and hard water slow down the rising process while soft water can make the
dough extra-sticky. If you find this to be a
problem, replace the tap water with bottled
water.
• Water can also be totally or partially replaced
with milk or other liquids.
• All liquids must be at room temperature.
Milk:
• Recipes can use either liquid or powdered
milk.
• Milk enhances the flavor and gives bread a
softer, ivory-colored texture.
• You can substitute the water called for in any
recipe with an equal amount of liquid milk.
• Many Basic Bread recipes call for powered
milk. It is important that you use powered
milk as it provides a better texture.
• 2% or fat-free milk provide the best results.
11
The following are the basic ingredients that you will use to make bread and dough, along with
some important tips and suggestions. Be sure to read this information, use fresh ingredients at
room temperature and measure carefully using measuring cups and spoons designed for cooking.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page11
Page 12
Eggs:
• Eggs make the dough richer and give it a
more golden color.
• All recipes provided with your bread maker
were developed using large eggs (1 large egg
= approximately 1/4 cup of liquid); if your
eggs are bigger, reduce the amount of liquid
called for in the recipe accordingly. If they are
smaller, use more liquid.
• If you want to add eggs to a recipe, you will
have to reduce the quantity of liquid proportionally. Break the eggs into the graduated
beaker or a glass liquid measuring cup, and
then add liquid until you reach the quantity
of liquid indicated in the recipe.
Butter or Oil (fat):
• Fat makes the bread softer and tastier.
• Too much fat slows down rising.
• If you use butter, soften to room temperature
and cut it into small pieces so that it is distributed evenly throughout the dough.
• You can substitute 1 tablespoon of butter for
1 tablespoon of oil.
• Do not use hot, melted butter.
• Keep the fat from coming into contact with
the yeast, as it can inhibit the yeast from activating properly.
• Do not use low fat spreads or butter substitutes.
Sugar:
• Sugar acts as food for the yeast, flavors the
bread and can improve browning of the crust.
• You can use white sugar, brown sugar, honey
or real maple syrup when making bread.
• Do not use unrefined sugar or cubes.
• Artificial sweeteners cannot be substituted for
sugar as the yeast will not react with them.
Salt:
• Salt flavors the bread and regulates the
yeast's activity by slowing the rising action.
• Use table or kosher salt when making bread.
• Do not use coarse salt or salt substitutes.
• Salt should not come into contact with the
yeast.
Additional ingredients (soft cheeses, dried
fruits, nuts, herbs, etc.):
You can add a personal touch to your recipes by
adding a variety of additional ingredients.
When adding ingredients, be sure to:
• Add them following the beep for additional
ingredients, especially those that are soft such
as dried fruits.
• Add items like whole, shelled nuts and seeds
at the start of the kneading process to ensure
even distribution.
• Thoroughly drain moist ingredients like
canned or fresh fruits and vegetables and
olives.
• Do not add too large a quantity of additional
ingredients, especially cheese, fresh fruit and
fresh vegetables, as they can affect the development of the dough.
• Finely chop nuts as they can cut through the
loaf structure and reduce the cooked height.
Ready to Use Bread Mixes:
• Ready-to-use bread mixes can be found in
many local grocery stores. Follow the manufacturer's instructions when using these
mixes.
• Usually, the choice of the program will depend on the type of mix purchased. For example: Whole wheat bread - Program 3.
12
1. In
• Rea
wit
the
• Bre
len
sto
be
2. In
• Use
• Ma
wa
• A c
yea
yea
fra
qui
wa
• All
(un
me
• Pla
exa
• Yea
uid
• Liq
nor
hea
app
F. L
be
(ne
• Wh
pro
3. M
• Me
cup
• Spo
off
• Alw
bea
gla
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page12
Page 13
13
Tips for good bread and dough
1. Instructions and recipes:
• Read all instructional materials that came
with your bread maker and understand how
the appliance works.
• Bread made in your bread maker is of excellent quality. However, it will be different than
store bought or bakery bread. The bread will
be chewier and the crust thicker and crisper.
2. Ingredients:
• Use fresh ingredients at room temperature.
• Make sure that the yeast has not expired andwas stored properly.
• A common error is to think that adding more
yeast will make the bread rise more. Too much
yeast makes the structure of the bread more
fragile; the dough will rise too high, too
quickly, and then collapse while baking. Always use the amount specified in the recipe.
• All ingredients must be at room temperature
(unless otherwise indicated) and must be
measured exactly.
• Place all ingredients into the bread pan in the
exact order given in the recipe.
• Yeast should not come into contact with liquids, fat, sugar or salt.
• Liquids should be between 70° to 80° F, under
normal baking conditions. In case of high
heat, use liquids that are cooler than usual,
approximately 68° F, but no colder than 65°
F. Likewise, if it is cold in your kitchen, it may
be necessary to warm up the water or milk
(never exceeding 90° F).
• When making bread using the Express Bread
program, the liquid should be 90° to 104°F).
3. Measuring:
• Measure ingredients using kitchen measuring
cups and spoons.
• Spoon flour into the measuring cup and level
off with a knife.
• Always measure liquids with the graduated
beaker included with your bread maker or a
glass liquid measuring cup.
• Use the double spoon supplied to measure
teaspoons on one side and tablespoons on
the other.
• All spoon measures are level and not heaping.
• Incorrect measurements will give poor results
therefore do not sift dry ingredients or pack
them down.
4. Weather:
• Weather conditions can affect how the bread
comes out.
• Flour is very absorbent. Recipes may need to
be adjusted and more flour added during periods of high humidity.
• You may have to use less yeast (1/4 to 1 teaspoon less, depending on the loaf size) and
cooler water (68° F) when it's very hot out.
5.Altitude:
• High altitude affects how the dough develops
and the bread rises.
• If baking bread at 3,000 feet above sea level,
reduce the water or liquid by approximately 1
tablespoon every 1,000 feet above 3,000 feet;
do not decrease by more than 4 tablespoons.
6.Consistency:
• For best results, check the dough once it begins to come together. It should form a
smooth yet sticky to the touch ball which
comes away easily from the walls of the
bread pan.
• If all of the flour has not been blended into
the dough, add a little more water, a tablespoon at a time, up to 4 tablespoons.
• If the dough is too wet and sticks to the sides,
you may need to add a little flour, a tablespoon at a time, up to 4 tablespoons.
7. Crust and Baking:
• Always select medium crust color unless making bread that has a high sugar or fat content,
then you might want to choose light.
• If you plan to bake a second loaf, always
open the lid and wait 1 hour before beginning
the second loaf.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page13
Page 14
For e
chos
para
14
Cleaning and maintenance
• Unplug the appliance.
• Clean the appliance itself with a damp cloth.
Dry thoroughly - L.
• Wash the pan and kneading paddle in hot
soapy water.
If the kneading paddle remains stuck in the
pan, let it soak for 5 to 10 min.
• When necessary, the lid can be cleaned with
warm water and a sponge.
• Do not wash any part
in a dishwasher.
• For the appliance, do not
use harsh household cleaning
products, scouring pads or alcohol. Use a soft,
damp cloth.
• Never immerse the body of the appliance or
the lid.
8.Power failure:
• If there is a power failure or the machine is accidentally unplugged while making bread, the
machine has a 7-minute protection time during which the settings are saved. The cycle will
start again where it left off. Beyond that time,
the settings are lost.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page14
Page 15
Program 1: Basic White Bread
Ingredients 1 ½ lb. 2 lb.
Water 1 ¼ cups 1 ½ cups
Vegetable oil 3 tablespoons 4 tablespoons
Salt 1 ¼ teaspoons 1 ½ teaspoons
Sugar 2 tablespoons 3 tablespoons
Bread flour 3 cups 4 cups
Yeast* 1 teaspoon 1 ½ teaspoons
*Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, oil, salt, sugar, and flour to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Remove baked bread at the end of the program. Cool before slicing.
Program 2: French Bread
Ingredients 1 ½ lb. 2 lb.
Water 1 ¼ cups 1 ½ cups
Salt 1 teaspoon 1 ¼ teaspoons
Sugar 1 ½ teaspoons 2 teaspoons
Bread flour 3 cups 3 1/3 cups
Corn meal 2 tablespoons 3 tablespoons
Yeast* 1 teaspoon 1 ½ teaspoons
*Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, salt, sugar, flour, and corn meal to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Remove baked bread at the end of the program. Cool before slicing.
Recipes
For each recipe, add the ingredients in the exact order indicated. Depending on the recipe
chosen and the corresponding program, you can take a look at the summary table of preparation times (pages 24-25) and follow the breakdown for the various cycles.
15
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page15
Page 16
16
Program 3: Whole Wheat Bread
Ingredients 1 ½ lb. 2 lb.
Water 1 1/3 cups 1 1/2 cups
Vegetable oil 2 tablespoons 3 tablespoons
Salt 1 teaspoon 2 teaspoons
Sugar 2 teaspoons 1 tablespoon
Bread flour 1 1/3 cups 1 ½ cups
Whole wheat flour 1 ½ cups 2 cups
Yeast* 1 teaspoon 1 1/2 teaspoons
*Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, oil, salt, sugar, and flours to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Remove baked bread at the end of the program. Cool before slicing.
Program 4: Gluten-free Bread
Ingredients 1 ½ lb.
Water 1 1/2 cups
Vegetable oil 1 ½ tablespoons
Eggs 2 large
Apple cider vinegar 1 teaspoon
Salt 1 teaspoon
Sugar 1 tablespoon
Gluten-free flour mix* 3 cups
Xanthan gum* 2 teaspoons
Yeast** 1 tablespoon
*Gluten-free, all-purpose flour, specialty flours and Xanthan gum are available at many large
grocery stores, most health food stores or on-line. You can also blend your own gluten-free
all-purpose flour at home by combining: 1 cup brown or white rice flour, 1 cup cornstarch,
2/3 cup soy or sorghum flour, and 1/3 cup masa harina flour (this corn-based flour can be found
in the flour section of most supermarkets).
**Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, oil, eggs, vinegar, salt, sugar, flour and Xanthan gum to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. After mixing begins, use a rubber spatula to help any unmixed ingredients into the dough,
keeping to the edges of batter to prevent interference with the paddle.
5. Remove baked bread at the end of the program. Cool before slicing.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page16
Page 17
Program 5: Sweet Bread
Ingredients 1 ½ lb. 2 lb.
Water 1 cup, plus 2 tablespoons 1 ½ cups
Vegetable oil 2 tablespoons 3 tablespoons
Salt 1 teaspoon 1 ½ teaspoons
Sugar 3 tablespoons 4 tablespoons
Extract* 1 teaspoon 1 ½ teaspoons
Bread flour 3 cups 4 cups
Yeast** 1 teaspoon 1 ½ teaspoons
Dried fruit*** ½ cup 2/3 cup
*Extract: Use orange, lemon or vanilla extract
**Active dry, quick-rise or bread machine yeast
***Dried cranberries, golden raisins, or chopped, dried apricots
Directions:
1. Add water, oil, salt, sugar, extract and flour to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Add dried fruit when the bread machine beeps during the second kneading.
5. Remove baked bread at the end of the program. Cool before slicing.
Program 6: Ultra Fast I
Ingredients 2 lb.
Water 1 2/3 cups
Vegetable oil 2 tablespoons
Salt 2 teaspoons
Sugar 1 ½ teaspoons
Bread flour 4 1/4 cups
Dried powdered milk 1 tablespoon
Yeast* 4 teaspoons
*Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, oil, salt, sugar, flour, and dried powdered milk to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Remove baked bread at the end of the program. Cool before slicing.
17
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page17
Page 18
Program 7: Ultra Fast II
Ingredients 1 ½ lb.
Water 1 ¼ cups
Vegetable oil 1 ½ tablespoons
Salt 1 ½ teaspoons
Sugar 1 teaspoon
Bread flour 3 ½ cups
Dried powdered milk 2 teaspoons
Yeast* 2 ½ teaspoons
*Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, oil, salt, sugar, flour, and dried powdered milk to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Remove baked bread at the end of the program. Cool before slicing.
Program 8: Pizza Dough
Ingredients
Water 1 cup
Olive oil 2 tablespoons
Salt 1 teaspoon
Bread flour 3 cups
Yeast* 2 ¼ teaspoons
*Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, oil, salt, and flour to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Remove dough at the end of the program.
Punch down dough; use at once to make your favorite pizza, focaccia or calzone recipe.
18
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page18
Page 19
Program 9: Apricot-Pineapple Jam
Ingredients
Dried apricots 16 ounces
Crushed pineapple, in heavy syrup 1 can (20-ounces) with syrup
Brown sugar 1/3 cup
Lemon juice 2 tablespoons
Water 1 ½ cups
Directions:
1. Add dried apricots, pineapple, sugar, lemon juice and water to the bread pan.
2. Close bread machine lid and press start.
3. At the end of the program, carefully spoon the cooked, hot mixture into the bowl of a food
processor or blender jar. Process until jam is smooth with small chunks of fruit.
Program 10: Citrus Loaf
Ingredients
Eggs 4 large
Sugar 1 1/4 cups
Unsalted butter, melted and cooled 8 tablespoons
Grated zest 1 large lemon or medium orange
Lemon or orange juice 1 freshly squeezed lemon or orange
All-purpose flour 3 cups
Baking powder 4 teaspoons
Salt Pinch
Directions:
1. In a bowl, whisk together the eggs and sugar until well-blended.
Add the melted butter, zest, and citrus juice. Whisk together. Pour into the bread machine pan.
2. In a bowl, sift together the flour, baking powder, and salt.
Add to the bread machine pan, mounding it in the center of the pan.
3. Close bread machine lid and press start.
4. After mixing begins, use a rubber spatula to help any unmixed ingredients into the dough,
keeping to the edges of batter to prevent interference with the paddle.
5. Remove baked loaf at the end of the program*.
Cool before slicing. Sprinkle with powdered sugar before serving.
*Note: If top of loaf appears undercooked at the end of the cycle, reset bread machine for bake
only (Program 12) and let cake cook an additional 15 minutes, or until it tests done.
19
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page19
Page 20
Program 11: Oatmeal Sandwich Bread
Ingredients 1 ½ lb. 2 lb.
Water 1/3 cup ½ cup
Buttermilk ¾ cup 1 cup
Vegetable oil 3 tablespoons ¼ cup
Salt 1 ½ teaspoons 2 teaspoons
Sugar 3 tablespoons ¼ cup
Bread flour 3 cups 4 cups
Oatmeal 1/3 cup ½ cup
Yeast* 2 ¼ teaspoons 1 tablespoon
*Active dry, quick-rise or bread machine yeast
Directions:
1. Add water, buttermilk, oil, salt, sugar, flour, and oatmeal to the bread pan.
2. Sprinkle yeast over the top.
3. Close bread machine lid and press start.
4. Remove baked bread at the end of the program. Cool before slicing.
20
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page20
Page 21
Troubleshooting guide to improve your recipes
Not getting the expected
results?
This table will help you.
Bread
rises
too much
Bread falls
after rising
too much
Bread does
not rise
enough
Crust not
golden
enough
Sides brown
but bread not
fully cooked
Top
and sides
floury
The button was pressed
during baking.
Not enough flour.
Too much flour.
Not enough yeast.
Too much yeast.
Not enough water.
Too much water.
Not enough sugar.
Poor quality flour.
Wrong proportions
of ingredients (too much).
Water too hot.
Water too cold.
Wrong program.
Technical troubleshooting guide
Problems Solutions
The kneading paddle is stuck
in the pan.
• Let it soak before removing it.
After pressing on ,
nothing happens.
• The screen displays HHH: the appliance is too hot.
Wait 1 hour between 2 cycles.
• The screen displays LLL: the appliance is too cold. Wait for it to reach
room temperature.
• The screen displays EE0: malfunction. The machine must be serviced
by authorized personnel.
•
A delayed start has been programmed.
After pressing on ,
the motor is on but no
kneading takes place.
• The pan has not been correctly inserted.
• Kneading paddle missing or not installed properly.
After a delayed start,
the bread has not risen
enough or nothing happens.
• You forgot to press on after programming the delayed start
program.
• The yeast has come into contact with salt and/or water.
• Kneading paddle missing.
Burnt smell. • Some of the ingredients have fallen outside the pan: unplug the
appliance, let it cool down, then clean the inside with a damp
sponge and without any cleaning product.
• The preparation has overflowed: the quantity of ingredients used
is too great, notably liquid. Follow the proportions given in the recipe.
21
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page21
Page 22
Quick guide to improve results
General problem solving: causes & solutions
Problem Cause Solution
Dough is
too sticky
a) Flour has high moisture content a) Only use bread flour that is stored in an airtight container;
try a different brand of flour
b) Too much liquid used b) Use less water; you can also add additional flour, a
tablespoon at a time, up to 4 tablespoons, to remedy
the problem while kneading dough
c) Water is soft c) Use bottled water
Dough or
bread
did not rise
enough or
at all
a) Ingredients were not at room
temperature
a) Make sure all ingredients (except yeast) are at room
temperature and water is between 70 and 90° F
b) Ingredients were not added to the
bread pan in the proper order adversely
affecting the yeast
b) Add ingredients in exact order as specified in the recipe
c) Yeast was inactive c) Check expiration date on the yeast packet or jar; store opened
packages of yeast in airtight containers in the
refrigerator or freezer
d) Low-gluten flour used d) Only use bread flour or a blend of bread flour and whole grain
flour
e) High altitude e) Reduce water by 1 tablespoon for every 1000 feet in
locations 3000 feet above sea level, up to 4 tablespoons
f) Hard water f) Use bottled water
g) Room temperature was below 68° F g) Only use bread maker in a location that is 68 to 80° F
h) Ingredients not measured properly h)Use measuring cups and spoons to measure dry ingredients
and theproper measuring cup for liquids. Do not sift or pack in-
gredients
i) The bread maker lid was opened too
much during the rising process
i) Do not open the bread maker lid during the rising process as
the machine is programmed to keep the bread maker at the
appropriate temperature to assist the yeast to grow and the
bread to rise.
Bread does
not bake
completely
or loaf is
too dense
a) Ingredients not measured correctly nor
at correct temperature
a) Use measuring cups and spoons to measure dry ingredients
and the proper measuring cup for liquids; do not sift or pack
ingredients; make sure ingredients are at room temperature
b) Yeast may have expired or has become
inactive
b) Only use fresh, properly stored yeast
c) Bread machine has turned off c) Perhaps there was a power outage or machine was
unplugged
Bread
collapses when
baked;
mushroom-top;
coarse large
holes
in loaf
Dough rose unevenly and or too quickly,
due to:
a) Excess moisture a) Only use bread flour and whole grain flour that is stored in
an airtight container
b) Too much liquid or too much yeast was
used
b) Measure all liquids using measuring cups specifically
designed for measuring liquids and measure accurately;
only use the amount of yeast specified in the recipe
c) No salt or not enough c) Use amount of salt specified in the recipe, or use Program 7
for Salt free bread
d) High humidity and / or heat d) Dough will rise too quickly and unevenly during hot and or
humid days; use cooler water (68° F)to slow down the rising
process or reduce the yeast 1/4 to 1 teaspoon depending on
the loaf size
22
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page22
Page 23
Problem Cause Solution
The bread
maker labors
during the
kneading cycle
or dough does
not come
together into
a ball after
kneading
Dough is too dry due to:
a) Ingredients not measured correctly a) Use measuring cups and spoons to measure dry ingredients
and measuring cups specifically designed for measuring
liquid ingredients. Do not sift or pack ingredients
b) Insufficient water b) Add additional water, a tablespoon at a time, up to 4
additional tablespoons
c) Hard water c) Use bottled water
d) Recipe includes eggs which were
smaller than a 1/4 cup of liquid
d) Break egg into measuring cup; if less than 1/4 cup, add water
or milk to make up the difference
Crust is too dark
or too hard
a) Crust setting was set too dark a) Set bread maker on lighter crust setting
b) Recipe has a lot of sugar or sweetener b) Bake sweet breads on the light setting
Crust is pale
and / or wet
a) Crust setting is set too light a) Set bread maker on a darker crust setting
b) Recipe has little or no sugar or fat b) Add a small amount of sugar and / or fat to the recipe
Gummy areas
in baked loaf
Butter or oil, as well as otheringredients
like cheese and fruit didnot blend well
with other ingredients
Too much fat or additional ingredients like cheese or fruit were
added to the dough or were added too late; butter was cold
and never blended in completely; only use room temperature
ingredients; do not exceed amount of additional ingredients
specified in the recipe.
Bread is stuck
in the loaf pan
The bread has remained in the loaf pan
too long
Removing the bread from the bread pan immediately after it
has baked will allow for the easiest removal
The paddles
get stuck in
the bread
Because the paddles are baked into the
bread, they will become part of the
finished result
a) Lightly oil the kneading paddles before adding the ingredients
in the bread pan.
b) Use the hook accessory to remove the paddles while the
bread is still hot. Lay the bread on its side (using oven mitts)
and insert the hook in the hole of the kneading paddle and
pull gently to release the kneading paddles.
c) You can also remove the paddles from the bread maker
before the baking cycle. See the “Cycle Chart”on page 9.
Slight smoke or
odor coming
from the bread
maker
a) As with all small appliances, it is normal
for some slight smoke or odor to come
from the product the first time it is used.
a) If it is not the first time you used the bread maker, check if
debris has dripped on or near the heating elements.
b) You have not removed all of the
packaging parts from the breadmaker.
b) Be sure that you have removed all packaging materials from
inside the bread maker.
c) Neither of the above causes are
present.
c) If there is no debris and this is still continuing, discontinue
use and contact our Consumer Services Department at
1-800-395-8325.
Machine stops
after kneading
Check to make sure you are using the
correct program.
Programs such as 8 (Bread dough) will only knead and 12
(loaf cooking) will knead and rise.
Neither of these programs will bake.
I am missing a
part that should
have come with
my bread maker
Please contact our Consumer Services Department at
1-800-395-8325.
I have read the
instruction
manual and
still do not
understand
how to use my
bread maker
Please contact our Consumer Service Department at
1-800-395-8325 and we will help you with any difficulty you
are having.
23
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page23
Page 24
1
Light
1.5 2:53 1:53 1:00
1:00
2:15
2 3:00 1:55 1:05 2:20
Medium
1.5 2:53 1:53 1:00 2:15
2 3:00 1:55 1:05 2:20
Dark
1.5 2:53 1:53 1:00 2:15
2 3:00 1:55 1:05 2:20
2
Light
1.5 3:40 2:35 1:05
1:00
2:35
2 3:50 2:40 1:10 2:40
Medium
1.5 3:40 2:35 1:05 2:35
2 3:50 2:40 1:10 2:40
Dark
1.5 3:40 2:35 1:05 2:35
2 3:50 2:40 1:10 2:40
3
Light
1.5 3:32 2:32 1:00
1:00
2:50
2 3:40 2:35 1:05 2:55
Medium
1.5 3:32 2:32 1:00 2:50
2 3:40 2:35 1:05 2:55
Dark
1.5 3:32 2:32 1:00 2:50
2 3:40 2:35 1:05 2:55
4
Light
- 2:10 1:00 1:10 1:00 1:45Medium
Dark
Browning Weight
(lbs)
Total time
(h)
Preparing the dough
(Kneading-Rest-Rising)(h)
Cooking
(h)
Keep warm
(h)
Extra
(h)
Table of cycles
The below table reflects the time each cycle takes to completely make your preparation, the times within the
total cooking times (preparing the dough & cooking), if there is a keep warm function, and the time reflected
on the machine if you would like to add extra ingredients like nuts (this is noted in the Extra column)
24
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page24
Page 25
Browning Weight
(lbs)
Total time
(h)
Preparing the dough
(Kneading-Rest-Rising)(h)
Cooking
(h)
Keep warm
(h)
Extra
(h)
5
Light
1.5 2:50
1:50
1:00
1:00
2:25
2 2:55 1:05 2:30
Medium
1.5 2:50 1:00 2:25
2 2:55 1:05 2:30
Dark
1.5 2:50 1:00 2:25
2 2:55 1:05 2:30
6
Light
2 1:38 0:48 0:50 1:00 1:28Medium
Dark
7
Light
1.5 1:28 0:43 0:45 1:00 1:18Medium
Dark
8
- - 1:30 - - - -
9
- - 1:20 - 0:20 - -
10
Light
- 1:50 0:30 1:20 1:00 1:34Medium
Dark
11
Light
1.5 2:55
2:05
0:50
1:00
1:59
2 3:00 0:55 2:04
Medium
1.5 2:55 0:50 1:59
2 3:00 0:55 2:04
Dark
1.5 2:55 0:50 1:59
2 3:00 0:55 2:04
12
Light
- 1:00 -
10 to
60 min.
1:00 -Medium
Dark
25
Comment: the total duration does not include warming time.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page25
Page 26
26
MANUFACTURER's WARRANTY
www.t-fal.com
With a strong commitment to the environment, most of T-fal products are repairableduring
and after the warranty period. Before returning any defective products to the point of purchase, please call T-fal consumer service directly at the phone number below for repair options.Your help to sustain the environment is appreciated!
The Warranty
This product is guaranteed by T-fal for 1 year against any manufacturing defect in materials
or workmanship, starting from the initial date of purchase.
The manufacturer's warranty by T-fal is an extra benefit which does not affect consumer's
Statutory Rights.
The T-fal warranty covers all costs related to restoring the proven defective product so that it
conforms to its original specifications, through the repair or replacement of any defective part and
the necessary labor. At T-fal’s choice, a replacement product may be provided instead of repairing
a defective product. T-fal’s sole obligation and your exclusive resolution under this warranty are
limited to such repair or replacement.
Conditions & Exclusions
The T-fal warranty only applies within USA, Canada & Mexico, and is valid only on presentation
of a proof of purchase. The product can be taken directly in person to an authorized service centre
or must be adequately packaged and returned, by recorded delivery (or equivalent method of
postage), to a T-fal authorized service centre. Full address details for each country’s authorized
service centre are listed on the T-fal website (www.t-fal.com) or by calling the appropriate telephone
number listed below to request the appropriate postal address.
T-fal shall not be obligated to repair or replace any product which is not accompanied by a valid
proof of purchase.
This warranty will not cover any damage which could occur as a result of misuse, negligence, failure
to follow T-fal instructions, use on current or voltage other than as stamped on the product, or a
modification or unauthorized repair of the product. It also does not cover normal tear and wear,
maintenance or replacement of consumable parts, and the following:
- using the wrong type of water or consumable
- scaling (any de-scaling must be carried out according to the instructions for use);
- immersion in water, or infiltration of dust, or insects into the product;
- mechanical damages, overloading
- damages or bad results due to wrong voltage or frequency
- accidents including fire, flood, lightning, etc
- professional or commercial use
- damage to any glass or porcelain ware in the product.
This warranty does not apply to any product that has been tampered with, or to damages incurred
through improper use and care, faulty packaging by the owner or mishandling by any carrier.
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page26
Page 27
27
The T-fal manufacturer's warranty applies only for products purchased and used in USA, Canada
& Mexico. Where a product purchased in one country and then used in another one:
a) The T-fal guarantee duration is the one in the country of usage of the product, even if the
product was purchased in another listed country with different guarantee duration.
b) The T-fal guarantee does not apply in case of non conformity of the purchased product
with the local standards, such as voltage, frequency, power plugs, or other local technical
specifications
c) The repair process for products purchased outside the country of use may require a longer
time if the product is not locally sold by T-fal
d) In cases where the product is not repairable in the new country, the T-fal guarantee is limited
to a replacement by a similar product or an alternative product at similar cost, where
possible.
Consumer Statutory Rights
This T-fal manufacturer's warranty does not affect the statutory rights a consumer may have
or those rights that cannot be excluded or limited, nor rights against the retailer from which the
consumer purchased the product. This warranty gives a consumer specific legal rights, and the
consumer may also have other legal rights which vary from State to State or Country to Country
or Province to Province. The consumer may assert any such rights at his sole discretion.
Additional information
Accessories, Consumables and end-user replaceable parts can be purchased, if locally available,
as described in T-fal internet site.
CANADA
GROUPE SEB CANADA
345 Passmore Avenue
Toronto, ON
M1V 3N8
1-800-418-3325
MEXICO
Groupe SEB MEXICO S.A. de C.V.
Goldsmith 38 Desp. 401 Col. Polanco
Delegacion Miguel Hildalgo
11 560 Mexico D.F. MEXICO
(01800) 112 83 25
U.S.A.
GROUPE SEB USA
2121 Eden Road
Millville, NJ 08332
800-526-5377
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page27
Page 28
Ref. NC00111292
www.t-fal.com
Tfal-ODM-US-NC00111292 09/05/12 15:52 Page28
Loading...