TFA HiTrax Trail User Manual [de]

Instructions Kat.Nr. 42.7000

ECHO MASTER II

FEATURES

NORMAL TIME, 12/24 HOUR FORMATS
2 DAILY ALARMS & HOURLY CHlME
1/100 S CHRONOGRAPH
10 LAP MEMORY
COUNTDOWN TIMER
PRE-SET OR USER SETTING
EL BACKLIGHT
SENSOR FUNCTIONS:
THERMOMETER, BAROMETER & ALTIMETER

FUNCTIONS:

PRESS BUTTON(B) OR BUTTON(D) TO SELECT FUNCTIONS:

DAILY ALARM -> STOP WATCH -> TIMER -> NORMAL ALTIMETER -> BAROMETER ->
NORMAL TIME

NORMAL TIME:

REAL TIME DISPLAY WITH DAY OF WEEK, MONTH, DATE, HOUR, MINUTE AND
SECOND

TO SET:

-HOLD BUTTON (A) FOR TWO SECONDS

-SECOND DIGITS WILL FLASH.

-PRESS BUTTON (D) TO RESET TO ZERO

-THEN PRESS BUTTON (C) TO SELECT / ADJUST MIN. HOUR AND SO ON...

- AT ANY TIME PRESS BU1TON (A) TO RETURN TO NORMAL TIME

- THE DAY OF WEEK IS AUTOMATICALLY SET IN ACCORDANCE WITH THE DATE.

- THE DATE CAN BE SET WITHIN THE RANGE OF 1/1/1997 AND 12/31/2049.

ALARM TIME:

IN NORMAL TIME MODE PUSHING BUTTON (B) CHANGES THE MODE TO ALARM
TIME, HOUR AND MINUTE. PRESS BUTTON (C) TO SELECT ALARM 1 OR 2.

ALM -ALARM TIME

- CHME SIGNAL ON

- ALARM SIGNAL ON

TO SET:

-HOW BUTTON (A) FÜR TWO SECONDS. TO ENTER INTO SETTING MODE.

-PRESS BUTTON (D) TO ADVANCE DIGITS

-PRESS BUTTON (C) TO SELECT / ADJUST.

CHRONOGRAPH:

1/100 SECOND CHRONOGRAPH OPERATION HAS A RANGE UP TO 23 HOURS 59
MINUTES & 59.99 SECONDS WITH 10 LAP MEMORY.

PLEASE DO NOT RESET THE VALUE IFYOU WANT TO KEEPYOUR LAP TIME RECORD
ON THE WATCH

COUNTDOWN TIMER:

COUNTDOWN TIMER WORKING RANGE IS 23 HOURS 59 MINUTES TO
ONE MINUTE THERE ARE 3 MIN, 5 MIN, 10 MIN, 15 MlN AND 45 MIN PRE-SETTED
VALUES, AND ONE USER SET VALUE.

AT ANY VALUE, PUSH BUTTON (C) TO START AND STOP COUNTING.

AT ANY TIME HOLD BUTTON (A) TO SET USER VALUE. THE SET VALUE WILL STAY
UNTIL ERASED

ALTIMETER:

- DIGITAL ALTIMETER FOR ALTITUDE MEASUREMENT WITH REFERENCE SETTING;
MEASURED RANGE FROM -702 M TO 9164 M OR -2309 FT TO 30149 FT AND THE
DISPLAY RANGE IS -9164 M TO 9164 M OR -30149 FT TO 30149 FT WHICH DEPENDS
ON THE REFERENCE SETTING; (ASSUME SEA LEVEL IS 1013.21MBAR & 0 M)

- IN NORMAL TIME MODE, PRESS BUTTON (D) TO SWITCH INTO ALTIMETER MODE.
THE "ALTI" INDICATOR WILL BE DISPLAYED.

- IN ALTIMETER MODE THE WATCH IS CAPABLE OF DlSPLAYlNG THE HEIGHT OF THE
ABSOLUTE VALUE AND THE OWN ALTITUDE OFFSET.

-RESET TO ABSOLUTE VALUE BY PRESSING BUTTON (A) FOR 2 SECONDS AND BY
PRESSING (A) AGAIN.

-SET REFERENCE VALUE TO ZERO OR OWN ALTITUDE OFFSET BY PRESSING (A)
FOR 2 SECONDS AND BY PRESSING BUTTON (D) & BUTTON (C).

I.E. HEIGHT FROM POINT (1) TO POINT (2) OR POINT (3):
AT POINT (1), HOLD BUTTON (A) FOR TWO SECONDS TO RESET ABSOLUTE VALUE
OF ALTIMETER AND THEN PUSH BUTTON (D) & BUTTON (C) TO SET REFERENCE
VALUE TO ZERO OR OWN ALTITUDE OFFSET. THEN USER CAN START MOVING UP
AND GET THE HEIGHT VALUE FROM POINT (1) TO POINT (2) OR POINT (3).

THERMOMETER & BAROMETER:

IN THE ALTIMETER MODE PRESS BUTTON (D) TO SWICH INTO BAROMETER MODE.
THE "BARO" INDICATOR WILL BE DISPLAYED.

- DIGITAL THERMOMETER FOR TEMPERATURE MEASURES OVER THE RANGE OF ­10°C TO + 60°C OR 14°F TO 140°F.

- DIGITAL BAROMETER FOR ABSOLUTE PRESSURE MEASURES OVER THE RANGE
OF 300 mbar to 1100 mbar OR 8 InHg TO 30 inHg.

TECHNICAL SPECIFICATIONS: