SPECIFICATION
Model: CD1412
Voltage: 220-240VAC,50Hz
Current: 1.5A
Paper entry width: 220mm
Shred size: 4mm x 35mm
Shred paper capacity: 12 A4 Sheets 70gsm/, 1 Credit Card, 1 x DVD/CD
Shred speed: 2 Mtrs/Min
Waste bin Volume: 14L
Noise level: 70.1db
Duty cycle: 2 Mins On/30 Mins Off
Net weight: 6.4Kgs
Dimension: 345 x 235 x 440mm
Type designation:
BS60950-1:2006
EMC Directive 2004/108/EC
Test Standards:EN55014-1:2006
EN55014-2:1997+A1:2001
EN61000-3-2:2006
EN61000-3-3:2008
Visit www.texet.com for details on other Texet products.
UK: Waste Electrical products/batteries should not be disposed of with household waste.
Separate disposal facilities exist, for your nearest facilities, see www.recycle-more.co.uk
or in store for details.
Made in China
Instruction manual
CROSS CUT SHREDDER
CD1412
Please Read the Following Instructions Carefully before Use, and Keep them for Future Use.
http://www.texet.com
CD/DVD Feed Slot
Paper Feed Slot
Control Buttons – Reverse Power Forward
To protect this Shredder correctly and avoid any damage, please
ensure you understand the following Icons:-
Please do not spray any flammable gas, water or oil onto this Shredder.
Please keep children away from the Shredder, the sharp blades may harm
them.
Please keep cloths, ties and the like away from the paper entry slot.
To prevent damage to the cutters remove paper clips and other
fasteners before shredding.
Please keep your hands out of the paper entry slot. The sharp blades
Inside the shredder may cause injury.
Please keep your hair away from the shredder/paper entry slot.
The incorrect operation of this appliance may cause personal injury or damage to
the shredder. The Plug Socket outlet should be easily accessible.
BS Plug Fuse – 3A Fitted
GENERAL SAFETY
When using electrical appliances, basic precautions should always be followed to reduce the
risk of fire, electrical shock and injury to persons including the following;
The Shredder is only intended for private/domestic and small office use. Any other uses not
recommended by the manufacture, may result in the warranty being void. Do not use the
shredder to shred film, OHP Pouches, adhesive stickers, cloths or any plastics, other that
credit cards, as these may cause damage.
Remove the Shredder from its packaging and check to make sure it is in good condition
before using. Keep the packaging for storage and transportation.
This Shredder is not intended for use by persons, including children, with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the Shredder by a person responsible
for their safety.
Extreme caution is necessary where children or persons with reduced physical, sensory or
mental capabilities may come into contact with the Shredder when in use.
Do not let children play with parts of the packaging, such as plastic bags.
Ensure the power supply to the socket into which the Shredder is plugged, is in accordance
with the rating label on the shredder and that the socket is earthed.
Do not use the Shredder if the Power Cord is damaged. If the Power Cord is damaged it
must be replaced by a recognized service agency or other qualified person.
Always turn the Power off before unplugging the Shredder and make sure your hands are
dry to prevent electric shock.
Do not use outdoors.
Always unplug the Shredder when not in use.
Shredder Capacity:
The CD1412 will shred 12 sheets of A4 70g paper at once or 1 Credit Card or 1 x DVD/CD,
and will accept paper width up to 220mm.When shredding smaller items like envelopes or
credit card receipts/Credit Cards, insert them through the middle of the feed slot.
The paper sensor is located in the centre of the main feed slot. When paper is inserted, the
sensor starts the cutters. When the paper has gone through the shredder, the sensor will
switch the cutters off.
Operating the Shredder:
1. Prepare the paper to be shredded by removing paper clips, and any other objects that
may jam in the feed slot. The Shredder will shred staples, though for optimal
performance, their removal is advised
2. Only feed 12 sheets of 70g A4 paper at any one time or 1 Credit Card or 1 DVD/CD
PLEASE NOTE
– There are two power switches/buttons on this Shredder, one at the back
of the Shredder, the other at the front.
Switches located at the back of the Shredder
O: Power on when pressed down
-
: Power off when pressed down
Buttons located at the front of the Shredder
REVERSE: Reverses the shredding direction and backs items out of the shredder in the
event of a paper jam, can also be used in conjunction with the Forward button, to clear paper
jams.
POWER: Press once to switch the power on, indicated by the Red ready light, press again
and the power is switched off. For this button to work the Rocker switch located at the back
of the shredder, must have the O switch pressed down.
FORWARD: Allows the cutters/blades to shred in a forward direction without paper being
inserted, normally used in conjunction with the reverse switch to clear any paper jams.
Waste Bin:
This Shredder has a pull out waste bin for mess free emptying. It is also fitted with a Safety
Switch that cuts off the power when the waste bin is removed. To switch it back on when the
bin is placed back into the Shredder, press the power button at the front of the Shredder.
PLEASE NOTE – If the waste bin is not placed back correctly, the Shredder will not work.
The Shredder is on castor for easy movability
Paper Jams:
The CC1610 is equipped with a motor overload/overheat protection device and the power
may terminate automatically in case of the following situations:
1. Operating the shredder at maximum capacity continuously for a prolonged period of
time, e.g. more than 2 minutes duty cycle without stopping.
2. Exceeding the shredding capacity e.g. inserting more than 12 sheets at one time, or if
the paper is not fed squarely into the feed slot.
Both of these operations may result in the activation of the automatic motor overload
protection, which terminates the power to the unit. If this occurs, you should either:
1 . Press the reverse button and remove any excess paper, now press the forward button,
this should then clear the paper jam. If the paper is still jammed in the blades then
alternately press the forward and reverse buttons 2-3 times, the paper jam should now
be cleared.
OR
2 If the Shredder does not work then you need to unplug the power cord from the AC
outlet and wait at least 30 minutes for the overload protection to reset.
3 After 30 mins, plug the power cord back into the AC outlet and press the power button,
so the red ready light comes on. Any paper still in the shredder should automatically be
shredded, if not follow the above instructions in point 1.
Clearing the Blades of Paper Jams
If paper becomes jammed during shredding, press the reverse button and remove any
excess paper from the feed slot, press the forward button, this should clear the paper jam.. If
paper is still jammed then press the forward and reverse buttons alternately, 2-3 times,
which should then finally clear the paper jam.
ALWAYS UNPLUG THE SHREDDER BEFORE ATTEMPTING TO MANUALLY REMOVE
AN ITEM FROM THE PAPER ENTRY.
DO NOT, UNDER ANY CIRCUMSTANCES, INSERT METAL OBJECTS INTO THE ENTRY
FEED SLOT OR THE BLADES, TO REMOVE THE JAMMED PAPER.
Maintenance
Warning:
When you want to maintain the shredder, please make sure you have switched off the
shredder and removed the plug from its socket.
Use a damp/dry soft cloth when you want to clean the shredder.
The shredder cover and waste bin are made of plastic; therefore please do not use
gasoline, benzene impregnate thinners to avoid fading or scratches.
Do not allow water to enter the shredder head when cleaning.
To maintain the quality of your shredder blades please use Texet LB12 lubricating
sheets once a month, these can be bought from our ebay store – Texet Sales Ltd.
Waste Emptying:
1. When you empty the waste bin, please make sure the shredder is switched off and
unplugged.
2. Place the Waste Bin back into the shredder, ensuring it is done correctly otherwise it will
not work.
Paper can easily wrap around the shredder blades if the waste bin is allowed
to get too full, therefore please empty the waste bin after shredding approx
85 A4 Sheets.
Disposal:
Please dispose of this product responsibly at an approved disposal site or recycling facility.
Do not dispose of this product in household waste.
TROUBLE SHOOTING
Troubles Reason Solution
Shredder does
not work after
paper is
inserted.
1. The power cord may not be
properly connected.
2. The motor has been over
heated.
3. The paper feed may be
jammed.
4. Waste Bin not replaced
correctly after emptying..
1. Check the power cord is correctly
plugged in both the plug socket and the
shredder.
2. Wait for about 30 minutes and try the
shredder again.
3. Reverse the paper feed and remove any
jammed paper, then try again.
4. Check Waste Bin has been put back
correctly.
Shredder does
not stop after
shredding has
finished
1. The mechanical sensor may
be jammed by paper
1. Clean the paper entry and try again,
ensuring you remove the plug from the
socket first.
Shredder
makes a high
noise
1. The shredder may not be
placed on a flat/stable surface.
1. Replace the shredder onto a flat/stable
surface.
Shredder does
not shred paper
1. Too much paper is inserted.
2. The paper size inserted may
be larger than the paper entry.
3. The paper may be inclined
when placed into the paper
entry.
1. Check to see if you have exceeded the
rated capacity of paper (12
sheets of 70 g).
2. Reverse the shredder and take out the
paper, fold in half and try again.
3. Re-insert the paper vertically.
Loading...