SPECIFICATION
Model: CC15M
Voltage: 220-240VAC,50Hz
Current: 1.0A
Paper entry width: 220mm
Shred size: 4*20mm
Shred paper capacity: 6sheets 70gsm
Shred speed: 2.5m/min
Waste bin Volume: 15L
Noise level: 74dB
Duty cycle: 2 mins on and 60mins off
Net weight: 3.2KGs
Dimension: 314*181*395mm
Type designation:
Testing acc. to BSEN 60950-1:2006
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
Test Standards:EN55014-1:2006
EN55014-2:1997+A1:2001
EN61000-3-2:2006
EN61000-3-3:2008
Visit www.texet.com for details on other Texet products.
Instruction manual
CROSS CUT SHREDDER
CC15M
Please Read The Following Instructions Carefully before Use, and Keep It for Future Use.
http://www.texet.com
Thank you for purchasing the TEXET Cross Cut Shredder, CC15M, with normal use and
maintenance, your shredder will provide years of satisfactory performance. Please read
the instruction manual carefully and retain for future reference.
Figure 1
To protect this shredder correctly and avoid any damage, please make sure you understand
the following icons:
Cautions:
The incorrect operation may cause personal injury or damage property.
The plug socket outlet should be easily accessible.
BS plug fuse maximum 3A.
WARNING
Please keep children away from
this shredder.
Please keep your hair away from
the shredder.
The sharp blade inside the
shredder may harm children.
Please keep your hands out of the
paper entry.
Please do not spray any
flammable gas or oil onto this
shredder, it may cause fire.
The sharp blade inside the
shredder may cause injury.
Please keep soft cloths, ties away
from the paper entry.
If smoke or abnormal smells
come from the shredder,
please stop using it immediately
and remove the plug from the
socket.
ATTENTION
This shredder is intended for small office and home use only.
This shredder is a paper shredder;
please do not use it to shred film,
OHP pouches, adhesive stickers,
cloth or plastics as these may cause
damage.
Please do not use the shredder in
a hot, cold, humid or dirty place.
Please do not spray any water
onto the shredder.
Please do not open the shredder or
try to repair it yourself.
Please remove the plug from the
socket when emptying the waste
bin or when not in use.
Please keep ties, necklace & hair
away from the shredder, as it may
cause personal injury. If they are
taken into the shredder, please turn
the power off immediately.
Please place your hands in a safe
position when both inserting &
removing the plug from the socket.
Please place the shredder on a flat /
stable surface.
The shedder should be used close
to the plug socket.
Please do not put anything on top of
the shredder.
Please use the shredder with the
correct power supply.
OPERATIONS
Figure 2
Setup:
1. Remove the shredder from the outer carton.
2. Place the shredder head onto the basket. If the shredder head does not make complete
contact with the basket then the device will not operate.
Shredder Capacity:
The CC15M will shred 6 sheets of A4 70g paper at once and will accept paper width up to
220mm.When shredding smaller items like envelopes or credit card receipts, insert them
through the middle of the feed slot.
Operating Switch
Feed Slot
Shredder Bin
Operating the Shredder:
1. Prepare the paper to be shredded by removing paper clips and any other objects that
may jam in the feed slot. However, please note the shredder can shred staples, though
for optimal performance, their removal is advised.
2. Only feed 6 sheets of 70g A4 paper at any one time.
3. Set the select switch on top of the shredder to REV, OFF or AUTO position for the
desired operation ( see Figure 2).
AUTO
: Activates the auto shred function, the shredder will start automatically when an item
is inserted into the paper feed slot and will stop once the paper has been shredded.
REV
: Reverses the shredding direction and backs items out of the shredder in the event of a
jam.
OFF
: This position is recommended when emptying the shredder bin or when the shredder
is not in use for a prolonged period of time.
Paper Jams:
The CC15M is equipped with a motor overload protection device; the normal short duty cycle
for continuous shredding a maximum capacity is 2 minutes on & 60 minutes off. The power
may terminate automatically in case of the following situations:
1. Operating the shredder at maximum capacity continuously for a prolonged period of
time, e.g. more than 2 minutes without stopping.
2. Exceeding the shredding capacity e.g. inserting more than 6 sheets at one time, or if the
paper is not fed squarely into the feed slot.
Both of these operations may result in the activation of the automatic motor overload
protection, which terminates the power to the unit. If this occurs, you should:
1. Unplug the power cord from the AC outlet and wait at least 60 minutes for the overload
protection to reset. Tear or cut off any excess paper from the top of the shredder.
2. Plug the power cord back into the AC outlet and place the switch in REV. Pull the
remaining paper out of the cutters. Place the switch back to the AUTO position if
necessary.
3. With the switch in the AUTO position and the feed slot clear, you are now ready to
resume normal shredding.
If the shredder overheated, it will automatically shut down and will restart again after 60
minutes.
Clearing the Cutter Heads
If fibrous paper is being shredded the cutters may become clogged. Move the switch
alternatively between AUTO and REV 2-3 times to clear any paper shreds attached to the
cutters.
ALWAYS UNPLUG THE SHREDDER BEFORE ATTEMPTING TO MANUALLY REMOVE
AN ITEM FROM THE PAPER ENTRY.
Maintenance
When you want to maintain the shredder, please make sure you have switched
off the shredder and removed the plug from its socket.
Use a dry soft cloth when you want to clean the shredder.
The shredder cover and waste bin are made of plastic; therefore please do not use
gasoline, benzene impregnate thinner to avoid fading or scratches.
Do not allow water to enter the shredder head when cleaning.
Waste Emptying:
1. When you empty the waste bin, please make sure the unit is switched off and
unplugged.
2. Place back the shredder head onto the bin correctly.
Paper is easily wrapped around the shredder head if the waste bin is
allowed to get too full, therefore, please empty the waste bin when the bin is
full.
Disposal:
Please dispose of this product responsibly at an approved disposal site or recycling facility.
Do not dispose of this product in household waste.
TROUBLE SHOOTING
Troubles Reason Solution
Shredder
does not work
after paper is
inserted.
1. The power cord may not be
properly connected.
2. The paper being shredded may
be too high to activate the sensor.
3. The motor has been over
heated.
4. The paper feed may be jammed.
5. Shredder head is not placed
properly on basket.
1. Check the power cord is
correctly plugged in both the plug
socket and the shredder.
2. Try a thicker paper or fold the
paper in half & try again.
3. Wait for about 60 minutes and
try the shredder again.
4. Reverse the paper feed and
remove any jammed paper, then
try again.
5. Place shredder head securely
on basket, correctly front facing,
ensuring contact with the basket is
made.
Shredder
does not
shred paper
1. Too much paper is being
inserted.
2. The paper size inserted may
be larger than the paper entry.
3. The paper may be inclined
when placed into the paper
entry.
1. Check to see if you have exceeded
the rated capacity of paper (6 sheets
of 70 g).
2. Reverse the shredder and take out
the paper, fold in half and try again.
3. Re-insert the paper vertically.
Troubles Reason Solution
Shredder
does not stop
after
shredding has
finished
1. The mechanical sensor may
be jammed by paper
1. Clean the paper entry and try again.
Shredder
makes a high
noise
1. The shredder may not be
placed on a flat surface.
1. Replace the shredder onto a flat
surface.
Loading...