TEXAS INSTRUMENTS UC1842A, UC1843A, UC1844A, UC1845A, UC2842A Technical data

Current Mode PWM Controller

FEATURES DESCRIPTION

Optimized for Off-line and DC to DC

•

Converters

Low Start Up Current (<0.5mA)

•

Trimmed Oscillator Discharge Current

•

Automatic Feed Forward Compensation

•

Pulse-by-Pulse Current Limiting

•

Enhanced Load Response Characteristics

•

Under-Voltage Lockout With Hysteresis

•

Double Pulse Suppression

•

High Current Totem Pole Output

•

Internally Trimmed Bandgap Reference

•

• 500kHz Operation

• Low R

O Error Amp

The UC1842A/3A/4A/5A family of control ICs is a pin for pin compati
ble improved version of the UC3842/3/4/5 family. Providing the nec
essary features to control current mode switched mode power
supplies, this family has the following improved features. Start up cur
rent is guaranteed to be less than 0.5mA. Oscillator discharge is
trimmed to 8.3mA. During under voltage lockout, the output stage
can sink at least 10mA at less than 1.2V for V

The difference between members of this family are shown in the table
below.

Part # UVLO On UVLO Off

UC1842A 16.0V 10.0V <100%

UC1843A 8.5V 7.9V <100%

UC1844A 16.0V 10.0V <50%

UC1845A 8.5V 7.9V <50%

application

INFO

available

UC1842A/3A/4A/5A
UC2842A/3A/4A/5A
UC3842A/3A/4A/5A

-

-

-

CC over 5V.

Maximum Duty

Cycle

BLOCK DIAGRAM

Note 1: A = DIL-8 Pin Number. B = SO-14 Pin Number.
Note 2: Toggle flip flop used only in 1844A and 1845A.

SLUS224A - SEPTEMBER 1994 - REVISED APRIL 2002

A/B

CONNECTION DIAGRAMS

ABSOLUTE MAXIMUM RATINGS (Note 1)

Supply Voltage (Low Impedance Source) . . . . . . . . . . . . . . 30V

Supply Voltage (I

Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±1A

Output Energy (Capacitive Load). . . . . . . . . . . . . . . . . . . . . 5µJ

Analog Inputs (Pins 2, 3). . . . . . . . . . . . . . . . . . . -0.3V to +6.3V

Error Amp Output Sink Current . . . . . . . . . . . . . . . . . . . . 10mA

Power Dissipation at T

Storage Temperature Range. . . . . . . . . . . . . . -65°C to +150°C

Lead Temperature (Soldering, 10 Seconds) . . . . . . . . . . 300°C

Note 1. All voltages are with respect to Ground, Pin 5. Currents
are positive into, negative out of the specified terminal. Consult
Packaging Section of Databook for thermal limitations and con
siderations of packages. Pin numbers refer to DIL package only.

SOIC-14 (TOP VIEW)
D Package

CC mA) . . . . . . . . . . . . . . . . . . . . Self Limiting

A ≤ 25°C (DIL-8) . . . . . . . . . . . . . . . . 1W

-

PLCC-20, LCC-20
(TOP VIEW)
Q, L Packages

UC1842A/3A/4A/5A
UC2842A/3A/4A/5A
UC3842A/3A/4A/5A

PACKAGE PIN FUNCTION

FUNCTION PIN

N/C
Comp 2
N/C 3-4
VFB 5
N/C 6
ISENSE 7
N/C 8-9
RT/CT 10
N/C 11
Pwr Gnd 12
Gnd 13
N/C 14
Output 15
N/C 16
VC 17
VCC 18
N/C 19
VREF 20

1

SOIC-WIDE16 (TOP VIEW)
DW Package

N/C

1

N/C

2

COMP

ISENSE

RT/CT

VFB

N/C

N/C

3

4

5

6

7

8

16

15

14

13

12

11

10

9

DIL-8, SOIC-8 (TOP VIEW)
J or N, D8 Package

N/C

VREF

VCC

VCC

OUTPUT

GND

PWRGND

N/C

2

UC1842A/3A/4A/5A
UC2842A/3A/4A/5A
UC3842A/3A/4A/5A

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for –55°C ≤ TA ≤ 125°C for the

UC184xA; –40°C ≤ T
(Note 5); R

T = 10k; CT = 3.3nF; TA =TJ; Pin numbers refer to DIL-8.

A ≤ 125°C for the UC284xAQ; –40°C ≤ TA ≤ 85°C for the UC284xA; 0 ≤ TA ≤ 70°C for the UC384xA; VCC = 15V

PARAMETER TEST CONDITIONS

UC184xA\UC284xA UC384xA

MIN. TYP. MAX. MIN. TYP. MAX.

UNITS

Reference Section

Output Voltage T
Line Regulation 12 ≤ V
Load Regulation 1 ≤ I

J = 25°C, IO = 1mA 4.95 5.00 5.05 4.90 5.00 5.10 V

IN 25V 6 20 6 20 mV

O ≤ 20mA 6 25 6 25 mV

Temp. Stability (Note 2, Note 7) 0.2 0.4 0.2 0.4 mV/°C
Total Output Variation Line, Load, Temp. 4.9 5.1 4.82 5.18 V
Output Noise Voltage 10Hz ≤ f ≤ 10kHz

J = 25°C (Note 2) 50 50 µV

T

Long Term Stability T

A = 125°C, 1000Hrs. (Note 2) 5 25 5 25 mV

Output Short Circuit -30 -100 -180 -30 -100 -180 mA

Oscillator Section

Initial Accuracy T
Voltage Stability 12 ≤ V
Temp. Stability T
Amplitude V
Discharge Current T

J = 25°C (Note 6) 47 52 57 47 52 57 kHz

CC ≤ 25V 0.2 1 0.2 1 %
MIN ≤ TA ≤ TMAX (Note 2) 5 5 %
PIN 4 peak to peak (Note 2) 1.7 1.7 V
J = 25°C, VPIN 4 = 2V (Note 8) 7.8 8.3 8.8 7.8 8.3 8.8 mA
PIN 4 = 2V (Note 8) 7.5 8.8 7.6 8.8 mA

V

Error Amp Section

Input Voltage V

PIN 1 = 2.5V 2.45 2.50 2.55 2.42 2.50 2.58 V

Input Bias Current -0.3 -1 -0.3 -2

VOL 2 ≤ VO ≤ 4V 65 90 65 90 dB

A
Unity Gain Bandwidth T
PSRR 12 ≤ V
Output Sink Current V
Output Source Current V

OUT High VPIN 2 = 2.3V, RL = 15k to ground 5 6 5 6 V

V

OUT Low VPIN 2 = 2.7V, RL = 15k to Pin 8 0.7 1.1 0.7 1.1 V

V

J = 25°C (Note 2) 0.7 1 0.7 1 MHz

CC ≤ 25V 60 70 60 70 dB
PIN 2 = 2.7V, VPIN 1 = 1.1V 2 6 2 6 mA
PIN 2 = 2.3V, VPIN 1 = 5V -0.5 -0.8 -0.5 -0.8 mA

Current Sense Section

Gain (Note 3, Note 4) 2.85 3 3.15 2.85 3 3.15 V/V
Maximum Input Signal V
PSRR 12 ≤ V

PIN 1 = 5V (Note 3) 0.9 1 1.1 0.9 1 1.1 V

CC ≤ 25V (Note 3) 70 70 dB

Input Bias Current -2 -10 -2 -10
Delay to Output V

PIN 3 = 0 to 2V (Note 2) 150 300 150 300 ns

Output Section

Output Low Level I

Output High Level I

Rise Time T
Fall Time T
UVLO Saturation V

SINK = 20mA 0.1 0.4 0.1 0.4 V
SINK = 200mA 15 2.2 15 2.2 V

I

SOURCE = 20mA 13 13.5 13 13.5 V
SOURCE = 200mA 12 13.5 12 13.5 V

I

J = 25°C, CL = 1nF (Note 2) 50 150 50 150 ns
J = 25°C, CL = 1nF (Note 2) 50 150 50 150 ns
CC = 5V, ISINK = 10mA 0.7 1.2 0.7 1.2 V

A

µ

A

µ

3

UC1842A/3A/4A/5A
UC2842A/3A/4A/5A
UC3842A/3A/4A/5A

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for –55°C ≤ TA ≤ 125°C for the

UC184xA; –40°C ≤ T
(Note 5); R

T = 10k; CT = 3.3nF; TA =TJ; Pin numbers refer to DIL-8.

A ≤ 125°C for the UC284xAQ; –40°C ≤ TA ≤ 85°C for the UC284xA; 0 ≤ TA ≤ 70°C for the UC384xA; VCC = 15V

PARAMETER TEST CONDITIONS

UC184xA\UC284xA UC384xA

MIN. TYP. MAX. MIN. TYP. MAX.

UNITS

Under-Voltage Lockout Section

Start Threshold x842A/4A 15 16 17 14.5 16 17.5 V

x843A/5A 7.8 8.4 9.0 7.8 8.4 9.0 V
Min. Operation Voltage After x842A/4A 9 10 11 8.5 10 11.5 V
Turn On x843A/5A 7.0 7.6 8.2 7.0 7.6 8.2 V

PWM Section

Maximum Duty Cycle x842A/3A 94 96 100 94 96 100 %

x844A/5A 47 48 50 47 48 50 %
Minimum Duty Cycle 0 0 %

Total Standby Current

Start-Up Current 0.3 0.5 0.3 0.5 mA
Operating Supply Current V

CC Zener Voltage ICC = 25mA 30 34 30 34 V

V

PIN 2 =VPIN 3 = 0V 11 17 11 17 mA

Note 2: Ensured by design, but not 100% production tested.
Note 3: Parameter measured at trip point of latch with V

VPIN

∆

1

;0

V

Note 4: Gain defined as:

Note 5: Adjust V

CC

above the start threshold before setting at 15V.

A

=

VPIN

∆

3

PIN 3

PIN2

0.8V.

= 0.

Note 6: Output frequency equals oscillator frequency for the UC1842A and UC1843A. Output frequency is one half oscillator fre­quency for the UC1844A and UC1845A.
Note 7: “Temperature stability, sometimes referred to as average temperature coefficient, is described by the equation:

Temp Stability

VREF max VREF min

=

TJ max TJ min

−

() ()

−

() ()

.V

REF

(max) and V

REF

(min) are the maximum & minimum reference volt-

age measured over the appropriate temperature range. Note that the extremes in voltage do not necessarily occur at the extremes
in temperature.”
Note 8: This parameter is measured with R
The total current flowing into the R

T/Cpin will be approximately 300

T

= 10k to V

REF

.This contributes approximately 300 A of current to the measurement.

A higher than the measured value.

Error Amp Configuration

Error Amp can Source and Sink up to 0.5mA, and Sink up to 2mA.

4

Under-Voltage Lockout

Current Sense Circuit

UC1842A/3A/4A/5A
UC2842A/3A/4A/5A
UC3842A/3A/4A/5A

During UVLO, the Output is low.

Peak Current (I

A small RC filter may be required to suppress switch transients.

S) is Determined By The Formula

SMAX ′

I

1.0V

RS

Error Amplifier Open-Loop Frequency ResponseOutput Saturation Characteristics

5

APPLICATIONS DATA (cont.)

Oscillator Section

Oscillator Frequency vs Timing Resistance Maximum Duty Cycle vs Timing Resistor

UC1842A/3A/4A/5A
UC2842A/3A/4A/5A

Open-Loop Laboratory Test Fixture

High peak currents associated with capacitive loads necessi
tate careful grounding techniques. Timing and bypass capaci
tors should be connected close to pin 5 in a single point

Slope Compensation

-

ground. The transistor and 5k potentiometer are used to sam

-

ple the oscillator waveform and apply an adjustable ramp to
pin 3.

A fraction of the oscillator ramp can be resistively
summed with the current sense signal to provide slope
compensation for converters requiring duty cycles over
50%.
Note that capacitor, C, forms a filter with R2 to suppress
the leading edge switch spikes.

-

6

APPLICATIONS DATA (cont.)

Off-line Flyback Regulator

UC1842A/3A/4A/5A
UC2842A/3A/4A/5A
UC3842A/3A/4A/5A

Power Supply Specifications

1. Input Voltage 95VAC to 130VA
(50 Hz/60Hz)

2. Line Isolation 3750V

3. Switching Frequency 40kHz

4. Efficiency Full Load 70%

5. Output Voltage:
A. +5V,

B. +12V,

C. -12V ,

5%; 1A to 4A load

±

Ripple voltage: 50mV P-P Max

3%; 0.1A to 0.3A load

±

Ripple voltage: 100mV P-P Max

3%; 0.1A to 0.3A load

±

Ripple voltage: 100mV P-P Max

7

PACKAGE OPTION ADDENDUM

www.ti.com

PACKAGING INFORMATION

Orderable Device Status

5962-8670405PA ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type
5962-8670405VPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type
5962-8670405VXA ACTIVE LCCC FK 20 1 TBD Call TI N / A for Pkg Type

5962-8670405XA ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

5962-8670406PA ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type
5962-8670406VPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type
5962-8670406VXA ACTIVE LCCC FK 20 1 TBD Call TI N / A for Pkg Type

5962-8670406XA ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

5962-8670407PA ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type
5962-8670407VPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type
5962-8670407VXA ACTIVE LCCC FK 20 1 TBD Call TI N / A for Pkg Type

5962-8670407XA ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

5962-8670408PA ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type
5962-8670408VPA ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type
5962-8670408VXA ACTIVE LCCC FK 20 1 TBD Call TI N / A for Pkg Type

5962-8670408XA ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

UC1842AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1842AJ883B ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1842AJQMLV ACTIVE CDIP JG 8 TBD Call TI Call TI

UC1842AL883B ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

UC1842ALQMLV ACTIVE LCCC FK 20 TBD Call TI Call TI

UC1843AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1843AJ883B ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1843AJQMLV ACTIVE CDIP JG 8 TBD Call TI Call TI

UC1843AL883B ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

UC1843ALQMLV ACTIVE LCCC FK 20 TBD Call TI Call TI

UC1844AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1844AJ883B ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1844AJQMLV ACTIVE CDIP JG 8 TBD Call TI Call TI

UC1844AL883B ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

UC1844ALQMLV ACTIVE LCCC FK 20 TBD Call TI Call TI

UC1845AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1845AJ883B ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC1845AJQMLV ACTIVE CDIP JG 8 TBD Call TI Call TI

UC1845AL883B ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type

UC1845ALQMLV ACTIVE LCCC FK 20 TBD Call TI Call TI

UC2842AD ACTIVE SOIC D 14 50 Green (RoHS &

UC2842AD8 ACTIVE SOIC D 8 75 Green (RoHS &

UC2842AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

UC2842AD8TR ACTIVE SOIC D 8 2500 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM

(1)

Package

Type

Package

Drawing

Pins Package

Qty

Eco Plan

no Sb/Br)

no Sb/Br)

no Sb/Br)

(2)

Lead/Ball Finish MSL Peak Temp

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

22-May-2006

(3)

Addendum-Page 1

PACKAGE OPTION ADDENDUM

www.ti.com

Orderable Device Status

(1)

Package

Type

Package

Drawing

Pins Package

Qty

Eco Plan

(2)

Lead/Ball Finish MSL Peak Temp

no Sb/Br)

UC2842AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2842ADG4 ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2842ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2842ADTRG4 ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2842ADW ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2842ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2842ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2842ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2842AJ OBSOLETE CDIP JG 8 TBD Call TI Call TI

UC2842AN ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC2842ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC2843AD ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843AD8 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843AD8TR ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843ADG4 ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843ADTRG4 ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2843ADW ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2843ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2843ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2843ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2843AJ OBSOLETE CDIP JG 8 TBD Call TI Call TI

UC2843AN ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC2843ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

22-May-2006

(3)

Addendum-Page 2

PACKAGE OPTION ADDENDUM

www.ti.com

Orderable Device Status

(1)

Package

Type

Package

Drawing

Pins Package

Qty

Eco Plan

UC2843AQ ACTIVE PLCC FN 20 46 Green (RoHS &

(2)

Lead/Ball Finish MSL Peak Temp

CU SN Level-2-260C-1 YEAR

no Sb/Br)

UC2843AQG3 ACTIVE PLCC FN 20 46 Green (RoHS &

CU SN Level-2-260C-1 YEAR

no Sb/Br)

UC2844AD ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AD8 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AD8TR ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844ADTRG4 ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC2844AN ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC2844ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC2844AQD ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AQD8 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AQD8R ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2844AQDR ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845AD ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845AD8 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845AD8TR ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845ADG4 ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845ADTRG4 ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC2845ADW ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC2845ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

22-May-2006

(3)

Addendum-Page 3

PACKAGE OPTION ADDENDUM

www.ti.com

Orderable Device Status

(1)

Package

Type

Package

Drawing

Pins Package

Qty

Eco Plan

UC2845AN ACTIVE PDIP P 8 50 Green (RoHS &

(2)

Lead/Ball Finish MSL Peak Temp

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC2845ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC3842AD ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3842AD8 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3842AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3842AD8TR ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3842AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3842ADG4 ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3842ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3842ADTRG4 PREVIEW SOIC D 14 2000 TBD Call TI Call TI

UC3842ADW ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3842ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3842ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3842ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3842AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC3842AN ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC3842ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

UC3843AD ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3843AD8 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3843AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3843AD8TR ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3843AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

CU NIPDAU Level-2-260C-1 YEAR

no Sb/Br)

UC3843ADG4 ACTIVE SOIC D 14 50 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3843ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3843ADTRG4 ACTIVE SOIC D 14 2500 Green (RoHS &

CU NIPDAU Level-1-260C-UNLIM

no Sb/Br)

UC3843AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC3843AN ACTIVE PDIP P 8 50 Green (RoHS &

CU NIPDAU N / A for Pkg Type

no Sb/Br)

22-May-2006

(3)

Addendum-Page 4

PACKAGE OPTION ADDENDUM

www.ti.com

Orderable Device Status

(1)

Package

Type

Package

Drawing

Pins Package

Qty

Eco Plan

UC3843ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

no Sb/Br)

UC3844AD ACTIVE SOIC D 14 50 Green (RoHS &

no Sb/Br)

UC3844AD8 ACTIVE SOIC D 8 75 Green (RoHS &

no Sb/Br)

UC3844AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

no Sb/Br)

UC3844AD8TR ACTIVE SOIC D 8 2500 Green (RoHS &

no Sb/Br)

UC3844AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

no Sb/Br)

UC3844ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

no Sb/Br)

UC3844ADTRG4 ACTIVE SOIC D 14 2500 Green (RoHS &

no Sb/Br)

UC3844AN ACTIVE PDIP P 8 50 Green (RoHS &

no Sb/Br)

UC3844ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

no Sb/Br)

UC3845AD ACTIVE SOIC D 14 50 Green (RoHS &

no Sb/Br)

UC3845AD8 ACTIVE SOIC D 8 75 Green (RoHS &

no Sb/Br)

UC3845AD8G4 ACTIVE SOIC D 8 75 Green (RoHS &

no Sb/Br)

UC3845AD8TR ACTIVE SOIC D 8 2500 Green (RoHS &

no Sb/Br)

UC3845AD8TRG4 ACTIVE SOIC D 8 2500 Green (RoHS &

no Sb/Br)

UC3845ADG4 ACTIVE SOIC D 14 50 Green (RoHS &

no Sb/Br)

UC3845ADTR ACTIVE SOIC D 14 2500 Green (RoHS &

no Sb/Br)

UC3845ADTRG4 ACTIVE SOIC D 14 2500 Green (RoHS &

no Sb/Br)

UC3845ADW ACTIVE SOIC DW 16 40 Green (RoHS &

no Sb/Br)

UC3845ADWG4 ACTIVE SOIC DW 16 40 Green (RoHS &

no Sb/Br)

UC3845ADWTR ACTIVE SOIC DW 16 2000 Green (RoHS &

no Sb/Br)

UC3845ADWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS &

no Sb/Br)

UC3845AJ ACTIVE CDIP JG 8 1 TBD A42 SNPB N / A for Pkg Type

UC3845AN ACTIVE PDIP P 8 50 Green (RoHS &

no Sb/Br)

UC3845ANG4 ACTIVE PDIP P 8 50 Green (RoHS &

no Sb/Br)

(1)

The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

(2)

Lead/Ball Finish MSL Peak Temp

CU NIPDAU N / A for Pkg Type

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU N / A for Pkg Type

CU NIPDAU N / A for Pkg Type

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-1-260C-UNLIM

CU NIPDAU Level-2-260C-1 YEAR

CU NIPDAU Level-2-260C-1 YEAR

CU NIPDAU Level-2-260C-1 YEAR

CU NIPDAU Level-2-260C-1 YEAR

CU NIPDAU N / A for Pkg Type

CU NIPDAU N / A for Pkg Type

22-May-2006

(3)

Addendum-Page 5

PACKAGE OPTION ADDENDUM

www.ti.com

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in

a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)

Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check

http://www.ti.com/productcontent for the latest availability information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements

for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)

(3)

MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder

temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.

22-May-2006

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.

Addendum-Page 6

MECHANICAL DAT A

MCER001A – JANUARY 1995 – REVISED JANUARY 1997

JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE

0.400 (10,16)

0.355 (9,00)

0.063 (1,60)

0.015 (0,38)

0.100 (2,54)

8

1

5

4

0.065 (1,65)

0.045 (1,14)

0.020 (0,51) MIN

0.023 (0,58)

0.015 (0,38)

0.280 (7,11)

0.245 (6,22)

0.310 (7,87)

0.290 (7,37)

0.200 (5,08) MAX
Seating Plane

0.130 (3,30) MIN

0°–15°

0.014 (0,36)

0.008 (0,20)

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8

4040107/C 08/96

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

MECHANICAL DATA

MLCC006B – OCTOBER 1996

FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER

28 TERMINAL SHOWN

A SQ

B SQ

19

20

22

23

24

25

21

12826 27

12

1314151618 17

0.020 (0,51)

0.010 (0,25)

MIN

0.342
(8,69)

0.442

0.640

0.739

0.938

1.141

A

0.358

(9,09)

0.458

(11,63)

0.660

(16,76)

0.761

(19,32)(18,78)

0.962

(24,43)

1.165

(29,59)

NO. OF

TERMINALS

**

11

10

9

8

7

6

5

432

20

28

44

52

68

84

0.020 (0,51)

0.010 (0,25)

(11,23)

(16,26)

(23,83)

(28,99)

MINMAX

0.307
(7,80)

0.406

(10,31)

0.495

(12,58)

0.495

(12,58)

0.850
(21,6)

1.047
(26,6)

0.080 (2,03)

0.064 (1,63)

B

MAX

0.358
(9,09)

0.458

(11,63)

0.560

(14,22)

0.560

(14,22)

0.858
(21,8)

1.063
(27,0)

0.055 (1,40)

0.045 (1,14)

0.028 (0,71)

0.022 (0,54)

0.050 (1,27)

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

0.045 (1,14)

0.035 (0,89)

0.045 (1,14)

0.035 (0,89)

4040140/D 10/96

MECHANICAL DAT A

MPDI001A – JANUARY 1995 – REVISED JUNE 1999

P (R-PDIP-T8) PLASTIC DUAL-IN-LINE

0.400 (10,60)

0.355 (9,02)

8

5

0.260 (6,60)

0.240 (6,10)

1

0.021 (0,53)

0.015 (0,38)

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001

4

0.070 (1,78) MAX

0.020 (0,51) MIN

0.200 (5,08) MAX

0.125 (3,18) MIN

0.100 (2,54)

0.010 (0,25)

Seating Plane

M

0.325 (8,26)

0.300 (7,62)

0.015 (0,38)

Gage Plane

0.010 (0,25) NOM

0.430 (10,92)
MAX

4040082/D 05/98

For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

MECHANICAL DATA

MPLC004A – OCT OBER 1994

FN (S-PQCC-J**) PLASTIC J-LEADED CHIP CARRIER

20 PIN SHOWN

Seating Plane

0.004 (0,10)

D

D1

13

4

E1E

8

9

NO. OF

PINS

**

D/E

19

13

18

14

0.032 (0,81)

0.026 (0,66)

0.050 (1,27)

0.008 (0,20) NOM

D1/E1

MINMAXMIN

MAX

D2/E2

MIN

0.180 (4,57) MAX

0.120 (3,05)

0.090 (2,29)

0.020 (0,51) MIN

D2/E2

D2/E2

0.021 (0,53)

0.013 (0,33)

0.007 (0,18)

MAX

M

20
28
44
52
68
84

NOTES: A. All linear dimensions are in inches (millimeters).

B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-018

0.385 (9,78)

0.485 (12,32)

0.685 (17,40)

0.785 (19,94)

0.985 (25,02)

1.185 (30,10)

0.395 (10,03)

0.495 (12,57)

0.695 (17,65)

0.795 (20,19)

0.995 (25,27)

1.195 (30,35)

0.350 (8,89)

0.450 (11,43)

0.650 (16,51)

0.750 (19,05)

0.950 (24,13)

1.150 (29,21)

0.356 (9,04)

0.456 (11,58)

0.656 (16,66)

0.756 (19,20)

0.958 (24,33)

1.158 (29,41)

0.141 (3,58)

0.191 (4,85)

0.291 (7,39)

0.341 (8,66)

0.441 (11,20)

0.541 (13,74)

0.169 (4,29)

0.219 (5,56)

0.319 (8,10)

0.369 (9,37)

0.469 (11,91)

0.569 (14,45)

4040005/B 03/95

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

1

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty . Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:

Products Applications

Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive

DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony

Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless

Mailing Address: Texas Instruments

Post Office Box 655303 Dallas, Texas 75265

Copyright  2006, Texas Instruments Incorporated