TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
1-W Output (VCC ≥ 4.5 V)
D
2.7-V to 9-V Input Operating Range
D
78% Typical Efficiency
D
160-kHz Fixed-Frequency Current-Mode
PWM Controller
D
EN Input Inhibits Operation and Reduces
Supply Current to 1 µA
D
Output Voltage Limited to VO ≤ 12 V– V
CC
D
Soft Start
D
8-Pin SOIC and DIP Packages
D
–40°C to 85°C Free-Air Temperature Range
D
Pin-for-Pin Compatible with MAX755
description
The TPS6755 is an adjustable inverting dc/dc converter capable of operating from inputs as low as 2.7 V . The
only external components required are an inductor, an output filter capacitor , an input filter capacitor, a reference
filter capacitor, two resistors, and a Schottky rectifier . An enable input is provided to shut down the inverter when
an output voltage is not needed. The typical supply current is 1.9 mA at no-load and is further reduced to 1-µA
when the enable input is low.
The device features a 160-kHz current-mode pulse-width-modulation (PWM) controller with a p-channel
MOSFET power switch. The gate drive uses the converter output to reduce the die area needed to realize the
0.4-Ω MOSFET. Soft start is accomplished with the addition of one small capacitor at SS. A 1.22-V reference
is available for external loads up to 125 µA.
The TPS6755 is attractive for board-level dc/dc conversion in computer peripherals and in battery-powered
equipment requiring high efficiency and low supply current.
Available in an 8-pin DIP or an 8-pin SOIC package, the TPS6755 operates over a free-air temperature range
of –40°C to 85°C.
EN
REF
SS
COMP
V
CC
OUT
GND
FB
TPS6755
1
2
3
4
8
7
6
5
1 µF
+
47 µF
+
82 pF
†
10 µF
10 µH
1N5817
100 µF
+
– 5 V
V
I
2.7 V to 9 V
ENABLE
†
Not required for loads of 100 mA or less
10.2 kΩ
42.2 kΩ
Figure 1. Typical Circuit
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1
2
3
4
8
7
6
5
EN
REF
SS
COMP
V
CC
OUT
GND
FB
D OR P PACKAGE
(TOP VIEW)
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright 1996, Texas Instruments Incorporated
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
SMALL OUTLINE
(D)
PLASTIC DIP
(P)
CHIP FORM
(Y)
–40°C to 85°C TPS6755ID TPS6755IP TPS6755Y
The D package is also available taped and reeled (TPS6755IDR).
functional block diagram
EN
EN
1
EN
_
+
5
4
Error
Amplifier
Voltage
Reference
6
2
x3
SS Clamp
1.2 MΩ
x3
R
S
Q
160-kHz
Oscillator
PWM
Comparator
Σ
Driver
FB
Power Switch PMOS
Overcurrent
Comparator
7
8
V
CC
OUT
FB
COMP
GND
REF
3
SS
Current-
Sense Amplifier
Drive Latch
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
chip information
These chips, when properly assembled, display characteristics similar to the TPS6755. Thermal compression
or ultrasonic bonding may be used on the doped aluminum bonding pads. The chips may be mounted with
conductive epoxy or a gold-silicon preform.
75
82
8881
2
3
455
TPS6755Y
(1)
(2)
(3)
(8)
(7)
(6)
EN
REF
SS
OUT
FB
V
CC
GND
BONDING PAD ASSIGNMENTS
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJ max = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
6
7
7
(4)
(5)
COMP
Terminal Functions
TERMINAL
NAME NO.
DESCRIPTION
EN 1 Enable. EN > 2 V turns on the TPS6755. EN ≤ 0.4 V turns it off.
REF 2 1.22-V reference voltage output. REF can source 125 µA for external loads.
SS 3 Soft start. A capacitor between SS and GND brings the output voltage up slowly.
COMP 4 Compensation. A capacitor to ground stabilizes the feedback loop.
FB 5 Feedback. FB connects to the dc/dc converter output.
GND 6 Ground
OUT 7 Power MOSFET drain connection
V
CC
8 Supply-voltage input
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
detailed description
The following descriptions refer to the functional block diagram.
current-sense amplifier
The current-sense amplifier, which has a fixed gain of 3, amplifies the slope-compensated current-sense
voltage (a summation of the voltage on the current-sense resistor and the oscillator ramp) and feeds it to the
PWM comparator.
driver latch
The latch, which consists of a set/reset flip-flop and associated logic, controls the state of the power switch by
turning the driver on and off. A high output from the latch turns the switch on; a low output turns it off. In normal
operation the flip-flop is set high during the clock pulse, but gating keeps the latch output low until the clock pulse
is over. The latch is reset when the PWM comparator output goes high.
enable (EN)
A logic low on EN puts the TPS6755 in shutdown mode. In shutdown, the output power switch, voltage
reference, and other functions shut off and the supply current is reduced to 10 µA maximum. The soft-start
capacitor is discharged through a 1.2-MΩ resistance and the output falls to zero volts.
error amplifier
The error amplifier is a high-gain differential amplifier used to regulate the converter output voltage. The
amplifier generates an error signal, which is fed to the PWM comparator, by comparing a sample of the output
voltage to the reference and amplifying the difference. The output sample is obtained from a resistive divider
connected between FB and REF. FB is connected externally to the converter output, and the divider output is
connected to the error-amplifier input. An 82-pF capacitor connected between COMP and GND is required to
stabilize the control loop for loads greater than 100 mA.
oscillator and ramp generator
The oscillator circuit provides a 160-kHz clock to set the converter operating frequency , and a timing ramp for
slope compensation. The clock waveform is a pulse, a few hundred nanoseconds in duration, that is used to
limit the maximum power switch duty cycle to 95%. The timing ramp is summed with the current-sense signal
at the input to the current-sense amplifier.
overcurrent comparator
The overcurrent comparator monitors the current in the power switch. The comparator trips and initiates a
soft-start cycle if the power-switch current exceeds 2 A peak.
power switch
The power switch is a 0.4-Ω p-channel MOSFET with current sensing. The drain is connected to OUT and the
source is connected to a current-sense resistor. The voltage across the resistor is proportional to current in the
power switch and is tied to the overcurrent comparator and the current-sense amplifier. In normal operation,
the power switch is turned on at the start of each clock cycle and turned off when the PWM comparator resets
the drive latch.
PWM comparator
The comparator resets the drive latch and turns off the power switch whenever the slope-compensated
current-sense signal from the current-sense amplifier exceeds the error signal.
reference
The 1.22-V reference is brought out on REF and can source 125-µA maximum to external loads. A 10-µF
capacitor connected between REF and GND is recommended to minimize noise pickup.
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SS clamp
The SS clamp circuit limits the signal level on error-amplifier output during start-up. The voltage on SS is
amplified and used to override the error-amplifier output until the error-amplifier voltage rises above that output,
at which point the error amplifier takes over. This prevents the input to the PWM comparator from exceeding
its common-mode range (i.e., error amplifier output too high to be reached by the current ramp) by limiting the
maximum voltage on the error-amplifier output during start-up.
Soft start causes the output voltage to increase to the regulation point at the controlled rate. The voltage on the
charging soft-start capacitor gradually raises the clamp on the error amplifier output voltage, limiting surge
currents at power up by increasing the current limit threshold on a cycle-by-cycle basis. A soft-start cycle is
initiated when either the enable (EN) signal is switched high or an overcurrent fault condition triggers the
discharge of the soft-start capacitor.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
D 725 mW 5.8 mW/°C 464 mW 377 mW
P 1175 mW 9.4 mW/°C 752 mW 611 mW
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
†
Pin voltages: V
CC
(see Note 1) –0.3 V to 9 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OUT to VCC 12.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FB (see Note 1) 25 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SS, COMP, EN voltage range (see Note 1) –0.3 V to V
CC
+0.3 V. . . . . . . . . . . . . . . . . . . . . . . .
Peak switch current 2 A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reference current 2.5 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperture range, T
A
–40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6mm (1/16 inch) from case for 10 s 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to network terminal ground.
recommended operating conditions
MIN NOM MAX UNIT
Supply voltage 2.7 9 V
Decoupling capacitor 1 µF
Input capacitor 47 µF
Reference capacitor 10 µF
Output capacitor 100 µF
Compensation capacitor 82 pF
Inductor 10 µH
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range, V
CC
= 5 V,
I
O
= 0, EN = 5 V, typical values are at T
A =
25°C (unless otherwise noted) (refer to Figure 15)
PARAMETER TEST CONDITION MIN TYP MAX UNIT
Supply current 1.9 mA
Standby current EN = 0.4 V 1 10 µA
High-level input threshold voltage, EN 2 V
Low-level input threshold voltage, EN 0.4 V
Input current, EN –1 1 µA
Impedance, COMP 7.5 kΩ
Oscillator frequency 160 kHz
Reference voltage I
O(ref)
≤ 125 µA 1.22 V
Reference drift 50 ppm/°C
On resistance, OUT 0.4 Ω
Leakage current, OUT 20 nA
Startup voltage 2.7 V
performance characteristics over recommended operating free-air temperature range, typical
values at T
A
= 25°C (unless otherwise noted) (refer to Figure 15)
PARAMETER TEST CONDITION MIN TYP MAX UNIT
Output voltage
VCC = 4 V to 7 V
IO = 0 mA to 200 mA
–4.75 –5 –5.25 V
VCC = 2.7 V 125
Load current
VCC = 4 V 175
mA
VCC = 4.5 V 200 270
Line regulation VCC = 4 V 0.4%
Load regulation IO = 25 mA to 200 mA 0.4%
Efficiency IO =100 mA 78%
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
typical system waveforms
VI = 5 V
VO = – 5 V
IO = 100 mA
0
0.5
1
5
0
– 5
Voltage at OUT – V
I – Inductor Current – A
t – Time – s
2.5 µs/div
Figure 2. Switching Waveforms
2.5 µs/div
I – Inductor Current – A
– 50
0
– Output Voltage – mV
0
0.5
t – Time – s
VI = 5 V
VO = – 5 V
IO = 100 mA
1
V
O
Figure 3. Output Voltage Ripple
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
– Load Current – AI
L
0.2
0.1
Output Voltage Ripple – mV
50
0
–50
5 ms/div
t – Time – s
0
VI = 5 V
VO = – 5 V
IO = 0 mA to 200 mA
Figure 4. Load Transient Response
20
6
4
2
0
– 20
– Input Voltage – V
V
I
Output Voltage Ripple – mV
t – Time – s
500 µs/div
VI = 4 V to 7 V
VO = – 5 V
IO = 100 mA
8
0
Figure 5. Line Transient Response
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
6
4
2
0
– 2
– 4
– 6
Voltage at EN – V
– Output Voltage – V
V
O
2.5 ms/div
t – Time – s
VI = 5 V
VO = –5 V
IO = 100 mA
0
Figure 6. Enable Response Time
system typical characteristics
Figure 7
EFFICIENCY
vs
LOAD CURRENT
IL – Load Current – mA
Efficiency – %
75
73
71
70
25 50 75 100 125 150 175
76
79
80
200 225 250 300
78
77
74
72
275
TA = 25°C
(see Figure 15)
VI = 5 V
VI =7 V
VI =2.7 V
Figure 8
IL – Load Current – mA
Peak Inductor Current – A
PEAK INDUCTOR CURRENT
vs
LOAD CURRENT
0.8
0.6
0.2
0
0 50 100 150
1
1.4
1.6
200 250 300
1.2
0.4
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
Figure 9
No-Load Supply Current – mA
Supply Voltage – V
NO-LOAD SUPPLY CURRENT
vs
SUPPLY VOLTAGE
1
0.6
0.2
0
012 3 4
1.2
1.8
2
567
1.6
1.4
0.8
0.4
IO = 0 A
(see Figure 15)
Figure 10
Maximum Load Current – mA
Supply Voltage – V
MAXIMUM LOAD CURRENT
vs
SUPPLY VOLTAGE
250
200
150
2 2.5 3 3.5 4 4.5 5
300
350
400
5.5 6 6.5 7
(see Figure 15)
Figure 11
– Oscillator Frequency – kHz
OSCILLATOR FREQUENCY
vs
TEMPERATURE
T – Temperature – °C
f
osc
155
150
145
140
–40 –20 0 20 40 60
165
170
175
80 100 120 140
VI = 2.7 V
VI = 5 V
VCC = 7 V
160
Figure 12
Switch Current Limit – A
Soft-Start Voltage – mV
SWITCH CURRENT LIMIT
vs
SOFT-START VOLTAGE
0.8
0.6
0.2
0
0 200 400 600
1.2
1.6
1.8
800 1000 1200
1.4
1
0.4
VI = 2.7 V
VI = 5 V
VI =7 V
R1 and R2 Varied
(see Figure 15)
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
Figure 13
Soft-Start Delay – ms
SOFT-START DELAY
vs
CAPACITANCE
C – Capacitance – µF
50
40
20
0
0 0.2 0.4 0.6 0.8 1
60
80
90
1.2 1.4 1.6
C6 varied
(see Figure 7)
VI = 2.7 V
VI = 5 V
VI = 7 V
70
30
10
Figure 14
– Drain-Source On-State Resistance –
DRAIN-SOURCE ON-STATE RESISTANCE
vs
TEMPERATURE
r
DS(on)
Ω
T – Temperature – °C
0.3
0.2
0.1
0
–40 –20 0 20 40 60
0.5
0.6
0.7
80 100 120 140
0.4
VI = 7 V
VI = 2.7 V
VI = 5 V
The TPS6755 operates in the voltage-inverting circuit, shown in Figure 15, which can generate an output. The
circuit is ideal for applications that require a negative polarity voltage on the output with respect to the input
ground, and for energy management systems. The TPS6755 can be placed in a shutdown mode (1-µA
quiescent current) by forcing EN low.
soft start
The soft-start capacitor provides an orderly start-up of the converter by slowly increasing the switch current limit
during power-up. The soft-start timing is controlled by the SS capacitance (see Figure 13 for the capacitance
value corresponding to the desired delay time). The switch current limit is proportional to the voltage applied
to SS, which is internally pulled to REF by a 1.2-MΩ resistor. SS can be externally pulled lower than REF to limit
the switch current. A UVLO condition or an overcurrent condition initiates an SS cycle by discharging the SS
capacitor to ground through an internal transistor. A minimum of a 10-nF capacitor must be connected to SS
to current limit correctly.
inductor selection
The standard 10-µH inductor required by the TPS6755 must have a saturation current greater than the peak
switch current at the desired maximum load. Operation over the full voltage range and current range is assured
by the 10-µH inductor. To determine the required inductor staturation level, refer to the typical operating
characteristics graph for peak inductor current versus load current (see Figure 8).
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
output filter capacitor
A low equivalent series resistance (ESR) output filter capacitor is necessary to minimize the output-ripple
voltage. An ESR of 100 mΩ limits the output ripple to 90 mV or less for output loads up to 200 mA.
rectifier
A Schottky diode or high-speed silicon rectifier should be used with a maximum continuous current rating of
1 A for operation up to full load.
output ripple filtering
A low-pass filter may be added to the converter output to reduce the output voltage ripple (see Figure 15). The
LC filter has a cutoff frequency of 7.2 kHz. The inductor filter must have a low resistance to avoid large output
voltage drops. The output voltage ripple is reduced to 5 mV when the LC output filter is used. FB must be
connected to the output node before the connection for the low-pass filter.
adjustable output voltage
The output voltage of the TPS6755 is limited to VO ≤ 12 V – VCC and is set by two external resistors, R4 and
R5 (see Figure 15). R5 can be set to any value between 10 kΩ to 20 kΩ, and R4 is calculated using the following
formula: R4 = VO R5/1.22 V. These resistors form a voltage divider between FB, COMP, and REF. The
converter adjusts the output such that COMP level is at GND.
printed circuit board layout
A ground plane is recommended in a printed circuit board (PCB) layout to ensure quiet operation. Attention
should be given to minimizing the lengths of the switching loops. Bypass capacitors should be placed as close
to the TPS6755 as possible to prevent instability and noise pickup. V
CC
and GND should be bypassed directly
with a 1-µF ceramic capacitor and a large bypass capacitor (e.g. 47 µF) to maximize noise immunity. The
TPS6755 should not be used with IC sockets, wire-wrap prototype boards, or other constructions that are
susceptible to noise pick-up.
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
Optional
Low-Pass Output Filter
22 µH
22 µF
+
EN
REF
SS
COMP
V
CC
OUT
GND
FB
TPS6755ID
1
2
3
4
8
7
6
5
C4
82 pF
C3
10 µF
+
R1
130 kΩ
R2
300 kΩ
C1
47 µF
R3
10 kΩ
C5
1 µF
L1
10 µH
D1
1N5817
1 A, 20 V
+
C2
100 µF/10 V
V
O
V
I
ENABLE
+
C6
0.1 µF
R5
R4
R4 (kΩ)
42.2
16.7
75.2
R5 (kΩ)
10.2
10.2
10.2
VO (V)
–5
–2
–9
Figure 15. Application Circuit
Table 1. Bill of Materials
QTY DESCRIPTION
REF
DES
MANUFACTURER
PART NO.
MANUFACTURER
1 IC Power supply U1 TPS6755ID Texas Instruments
1 Diode Schottky D1 1N5817GI General Instrument
1 Inductor 10 µH L1
DO1608C-103
CD54-100
Coilcraft, Sumida
1 Capacitor 47 µF tantalum 16 V 7343 C1
593D476X9016D2W
TPSD476K016R0100
Sprague, AVX
1 Capacitor 100 µF tantalum 10 V 7343 C2
593D107X9010D2W
TPSD107D016R0100
Sprague, AVX
1 Capacitor 10 µF tantalum 10 V 3528 C3
293D106X0010B2W
267E 1002 106
Sprague, MATSUO
1 Capacitor 82 pF ceramic 50 V 0805 C4
1 Capacitor 1 µF ceramic 16 V 1206 C5
1 Capacitor 0.1 µF ceramic 50 V 0805 C6
1 Resistor 130 kΩ 0805 R1
1 Resistor 300 kΩ 0805 R2
1 Resistor 10 kΩ 0805 R3
1 Resistor 42.2 kΩ 1% 0805 R4
1 Resistor 10.2 kΩ 1% 0805 R5
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
4040047/B 03/95
0.228 (5,80)
0.244 (6,20)
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
1
14
0.014 (0,35)
0.020 (0,51)
A
0.157 (4,00)
0.150 (3,81)
7
8
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.010 (0,25)
PINS **
0.008 (0,20) NOM
A MIN
A MAX
DIM
Gage Plane
0.189
(4,80)
(5,00)
0.197
8
(8,55)
(8,75)
0.337
14
0.344
(9,80)
16
0.394
(10,00)
0.386
0.004 (0,10)
M
0.010 (0,25)
0.050 (1,27)
0°–8°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Four center pins are connected to die mount pad.
E. Falls within JEDEC MS-012
TPS6755
ADJUSTABLE INVERTING DC/DC CONVERTER
SLVS155A – NOVEMBER 1996 REVISED DECEMBER 1996
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
P (R-PDIP-T8) PLASTIC DUAL-IN-LINE PACKAGE
4040082/B 03/95
0.310 (7,87)
0.290 (7,37)
0.010 (0,25) NOM
0.400 (10,60)
0.355 (9,02)
58
41
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)
0.260 (6,60)
0.200 (5,08) MAX
0.125 (3,18) MIN
0.015 (0,38)
0.021 (0,53)
Seating Plane
M
0.010 (0,25)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
IMPORTANT NOTICE
T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
Loading...