Texas Instruments TPS2831PWP, TPS2831PWPR, TPS2831DR, TPS2830PWPR, TPS2831D Datasheet
...
TPS2830, TPS2831
FAST SYNCHRONOUS-BUCK MOSFET DRIVERS
WITH DEADTIME CONTROL
SLVS196B – JANUARY1999 – REVISED SEPTEMBER 1999
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Floating Bootstrap or Ground-Reference
High-Side Driver
D
Active Deadtime Control
D
50-ns Max Rise/Fall Times and 100-ns Max
Propagation Delay — 3-nF Load
D
Ideal for High-Current Single or Mutiphase
Applications
D
2.4-A Typ Peak Output Current
D
4.5-V to 15-V Supply Voltage Range
D
Internal Schottky Bootstrap Diode
D
SYNC Control for Synchronous or
Nonsynchronous Operation
D
CROWBAR for OVP, Protects Against
Faulted High-Side Power FETs
D
Low Supply Current . . . 3-mA Typ
D
–40°C to 125°C Junction-Temperature
Operating Range
description
The TPS2830 and TPS2831 are MOSFET drivers for synchronous-buck power stages. These devices are ideal
for designing a high-performance power supply using a switching controller that does not include suitable
MOSFET drivers on the chip. The drivers are designed to deliver 2.4-A peak currents into large capacitive loads.
Higher currents can be controlled by using multiple drivers in a multiphase configuration. The high-side driver
can be configured as a ground-reference driver or as a floating bootstrap driver. An adaptive dead-time control
circuit eliminates shoot-through currents through the main power FETs during switching transitions, and
provides high efficiency for the buck regulator. The TPS2830/31 drivers have additional control functions:
ENABLE, SYNC, and CROWBAR. Both drivers are off when ENABLE is low. The driver is configured as a
nonsynchronous-buck driver when SYNC is low. The CROWBAR function turns on the low-side power FET,
overriding the IN signal, for over-voltage protection against faulted high-side power FETs.
The TPS2830 has a noninverting input. The TPS2831 has an inverting input. The TPS2830/31 drivers are
available in 14-terminal SOIC and TSSOP packages and operate over a junction temperature range of –40°C
to 125°C.
AVAILABLE OPTIONS
PACKAGED DEVICES
T
J
SOIC
(D)
TSSOP
(PWP)
–40°C to 125°C
TPS2830D
TPS2831D
TPS2830PWP
TPS2831PWP
The D and PWP packages are available taped and reeled. Add R
suffix to device type (e.g., TPS2830DR)
Copyright 1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
1
2
3
4
5
6
7
14
13
12
11
10
9
8
ENABLE
IN
CROWBAR
NC
SYNC
DT
PGND
BOOT
NC
HIGHDR
BOOTLO
LOWDR
NC
V
CC
D OR PWP PACKAGE
(TOP VIEW)
NC – No internal connection
TPS2830, TPS2831
FAST SYNCHRONOUS-BUCK MOSFET DRIVERS
WITH DEADTIME CONTROL
SLVS196B – JANUARY1999 – REVISED SEPTEMBER 1999
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
functional block diagram
DT
6
IN
V
CC
LOWDR
BOOTLO
HIGHDR
BOOT
PGND
2
8
14
12
11
10
V
CC
7
ENABLE
1
SYNC
5
CROWBAR
3
(TPS2830 Only)
(TPS2831 Only)
Terminal Functions
TERMINAL
NAME NO.
I/O
DESCRIPTION
BOOT 14 I Bootstrap terminal. A ceramic capacitor is connected between BOOT and BOOTLO terminals to develop
the floating bootstrap voltage for the high-side MOSFET. The capacitor value is typically between 0.1 µF
and 1 µF . A 1-MΩ resistor should be connected across the bootstrap capacitor to provide a discharge path
when the driver has been powered down.
BOOTLO 11 O This terminal connects to the junction of the high-side and low-side MOSFETs.
CROWBAR 3 I CROWBAR can to be driven by an external OVP circuit to protect against a short across the high-side
MOSFET. If CROWBAR is driven low, the low-side driver will be turned on and the high-side driver will be
turned off, independent of the status of all other control terminals.
DT 6 I Deadtime control terminal. Connect DT to the junction of the high-side and low-side MOSFETs.
ENABLE 1 I If ENABLE is low, both drivers are off.
HIGHDR 12 O Output drive for the high-side power MOSFET
IN 2 I Input signal to the MOSFET drivers (noninverting input for the TPS2830; inverting input for the TPS2831).
LOWDR 10 O Output drive for the low-side power MOSFET
NC 4, 9, 13
PGND 7 Power ground. Connect to the FET power ground
SYNC 5 I Synchronous Rectifier Enable terminal. If SYNC is low, the low-side driver is always off; If SYNC is high,
the low-side driver provides gate drive to the low-side MOSFET.
V
CC
8 I Input supply. Recommended that a 1-µF capacitor be connected from VCC to PGND.
TPS2830, TPS2831
FAST SYNCHRONOUS-BUCK MOSFET DRIVERS
WITH DEADTIME CONTROL
SLVS196B – JANUARY1999 – REVISED SEPTEMBER 1999
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
detailed description
low-side driver
The low-side driver is designed to drive low Rds(on) N-channel MOSFETs. The current rating of the driver is
2 A, source and sink.
high-side driver
The high-side driver is designed to drive low Rds(on) N-channel MOSFETs. The current rating of the driver is
2 A, source and sink. The high-side driver can be configured as a GND-reference driver or as a floating bootstrap
driver. The internal bootstrap diode is a Schottky, for improved drive efficiency. The maximum voltage that can
be applied from BOOT to ground is 30 V.
deadtime (DT) control
†
Deadtime control prevents shoot through current from flowing through the main power FETs during switching
transitions by controlling the turn-on times of the MOSFET drivers. The high-side driver is not allowed to turn
on until the gate drive voltage to the low-side FET is low, and the low-side driver is not allowed to turn on until
the voltage at the junction of the power FET s (Vdrn) is low; the DT terminal connects to the junction of the power
FET s.
ENABLE
†
The ENABLE terminal enables the drivers. When enable is low, the output drivers are low.
IN
†
The IN terminal is the input control signal for the drivers. The TPS2830 has a noninverting input; the TPS2831
has an inverting input.
SYNC
†
The SYNC terminal controls whether the drivers operate in synchronous or nonsynchronous mode. In
synchronous mode, the low-side FET is operated as a synchronous rectifier. In nonsynchronous mode, the
low-side FET is always off.
CROWBAR
†
The CROWBAR terminal overrides the normal operation of the driver. When the CROWBAR terminal is low,
the low-side FET turns on to act as a clamp, protecting the output voltage of the dc/dc converter against over
voltages due to a short across the high-side FET. V
IN
should be fused to protect the low-side FET.
†
High-level input voltages on ENABLE, SYNC, CROWBAR, IN, and DT must be greater than or equal to VCC.
TPS2830, TPS2831
FAST SYNCHRONOUS-BUCK MOSFET DRIVERS
WITH DEADTIME CONTROL
SLVS196B – JANUARY1999 – REVISED SEPTEMBER 1999
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
†
Supply voltage range, V
CC
(see Note 1) –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range:BOOT to PGND (high-side driver ON) –0.3 V to 30 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BOOTLO to PGND –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BOOT to BOOTLO –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENABLE, SYNC, and CROWBAR (see Note 2) –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . .
IN (see Note 2) –0.3 V to 16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DT (see Note 2) –0.3 V to 30 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating virtual junction temperature range, T
J
–40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Unless otherwise specified, all voltages are with respect to PGND.
2. High-level input voltages on the ENABLE, SYNC, CROWBAR, IN, and DT terminals must be greater than or equal to VCC.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
D 760 mW 7.6 mW/°C 420 mW 305 mW
PWP 2400 mW 25 mW/°C 1275 mW 900 mW
recommended operating conditions
MIN NOM MAX UNIT
Supply voltage, V
CC
4.5 15 V
Input voltage BOOT to PGND 4.5 28 V
electrical characteristics over recommended operating virtual junction temperature range,
V
CC
= 6.5 V, ENABLE = High, CL = 3.3 nF (unless otherwise noted)
supply current
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
CC
Supply voltage range 4.5 15 V
V
ENABLE
= LOW, VCC =15 V 100 µA
V
ENABLE
= HIGH, VCC =15 V 0.1
V
CC
Quiescent current
V
ENABLE
= HIGH,
f
SWX
= 200 kHz,
C
HIGHDR
= 50 pF,
See Note 3
VCC =12 V ,
BOOTLO grounded,
C
LOWDR
= 50 pF,
3
mA
NOTE 3: Ensured by design, not production tested.
TPS2830, TPS2831
FAST SYNCHRONOUS-BUCK MOSFET DRIVERS
WITH DEADTIME CONTROL
SLVS196B – JANUARY1999 – REVISED SEPTEMBER 1999
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating virtual junction temperature range,
V
CC
= 6.5 V, ENABLE = High, CL = 3.3 nF (unless otherwise noted) (continued)
output drivers
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 4 V 0.7 1.1
High-side sink
Duty cycle < 2%
,
tpw < 100 µs
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 5 V 1.1 1.5
A
(see Note 4)
(see Note 3)
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
= 10.5 V 2 2.4
-
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 0.5V 1.2 1.4
High side
source
Duty cycle < 2%
,
tpw < 100 µs
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 1.5 V 1.3 1.6
A
Peak output-
(see Note 4) (see Note 3)
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
= 1.5 V 2.3 2.7
current
VCC = 4.5 V, V
LOWDR
= 4 V 1.3 1.8
Low-side sink
Duty cycle < 2%
,
tpw < 100 µs
VCC = 6.5 V, V
LOWDR
= 5 V 2 2.5
A
(see Note 4)
(see Note 3)
VCC = 12 V, V
LOWDR
= 10.5 V 3 3.5
-
VCC = 4.5 V, V
LOWDR
= 0.5V 1.4 1.7
Low side
source
Duty cycle < 2%
,
tpw < 100 µs
VCC = 6.5 V, V
LOWDR
= 1.5 V 2 2.4
A
(see Note 4) (see Note 3)
VCC = 12 V, V
LOWDR
= 1.5 V 2.5 3
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 0.5 V 5
High-side sink (see Note 4)
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 0.5 V 5
Ω
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
= 0.5 V 5
V
BOOT
– V
BOOTLO
= 4.5 V, V
HIGHDR
= 4 V 45
High-side source (see Note 4)
V
BOOT
– V
BOOTLO
= 6.5 V, V
HIGHDR
= 6 V 45
Ω
Output
V
BOOT
– V
BOOTLO
= 12 V, V
HIGHDR
=11.5 V 45
resistance
V
DRV
= 4.5 V, V
LOWDR
= 0.5 V 9
Low-side sink (see Note 4)
V
DRV
= 6.5 V V
LOWDR
= 0.5 V 7.5
Ω
V
DRV
= 12 V, V
LOWDR
= 0.5 V 6
V
DRV
= 4.5 V, V
LOWDR
= 4 V 45
Low-side source (see Note 4)
V
DRV
= 6.5 V, V
LOWDR
= 6 V 45
Ω
V
DRV
= 12 V, V
LOWDR
= 11.5 V 45
NOTES: 3. Ensured by design, not production tested.
4. The pullup/pulldown circuits of the drivers are bipolar and MOSFET transistors in parallel. The peak output current rating is the
combined current from the bipolar and MOSFET transistors. The output resistance is the Rds(on) of the MOSFET transistor when
the voltage on the driver output is less than the saturation voltage of the bipolar transistor.
deatime control
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
High-level input voltage
2 V
LOWDR
Low-level input voltage
Over the V
CC
range (see Note 3)
1 V
High-level input voltage
2 V
DT
Low-level input voltage
Over the V
CC
range
1 V
NOTE 3: Ensured by design, not production tested.
digital control terminals
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
High-level input voltage
2 V
Low-level input voltage
Over the V
CC
range
1 V
Loading...