TPA0211
2-W MONO AUDIO POWER AMPLIFIER
SLOS275B – JANUARY 2000 – REVISED MARCH 2000
IN
V
DD
DGN PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
V
O–
GND
SE/BTL
V
O+
D
Ideal for Wireless Communicators,
Notebook PCs, PDAs, and Other Small
Portable Audio Devices
D
2 W Into 4-Ω From 5-V Supply
D
0.6 W Into 4-Ω From 3-V Supply
D
Wide Power Supply Compatibility
SHUTDOWN
BYPASS
3 V to 5 V
D
Low Supply Current
– 4 mA Typical at 5 V
– 4 mA Typical at 3 V
D
Shutdown Control ... 1 µA Typical
D
Shutdown Pin is TTL Compatible
D
–40°C to 85°C Operating Temperature
Range
D
Space-Saving, Thermally-Enhanced MSOP
Packaging
description
The TPA0211 is a 2-W mono bridge-tied-load (BTL) amplifier designed to drive speakers with as low as 4-Ω
impedance. The device is ideal for use in small wireless communicators, notebook PCs, PDAs, anyplace a
mono speaker and stereo head phones are required. From a 5-V supply , the TPA021 1 can delivery 2-W of power
into a 4-Ω speaker.
The gain of the input stage is set by the user-selected input resistor and a 50-kΩ internal feedback resistor
(A
= – RF/ RI). The power stage is internally configured with a gain of –1.25 V/V in SE mode, and –2.5 V/V in
V
BTL mode. Thus, the overall gain of the amplifier is 62.5 kΩ/ R
in SE mode and 125 kΩ/ RI in BTL mode. The
I
input terminals are high-impedance CMOS inputs, and can be used as summing nodes.
The TP A0211 is available in the 8-pin thermally-enhanced MSOP package (DGN) and operates over an ambient
temperature range of –40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 2000, Texas Instruments Incorporated
1
TPA0211
MSOP
2-W MONO AUDIO POWER AMPLIFIER
SLOS275B – JANUARY 2000 – REVISED MARCH 2000
4
V
DD
V
DD
3
BYPASS
C
B
7
GND
Audio
Input
From
System Control
C
I
BYPASS
50 kΩ
R
I
1
IN
2
SHUTDOWN
–
+
BYPASS
50 kΩ
50 kΩ
–
+
BYPASS
Shutdown
and Depop
Circuitry
R
BYPASS
R
BYPASS
1.25*R
–
+
Stereo/Mono
Control
1.25*R
–
+
VO+
SE/BTL
VO–
C
5
100 kΩ
6
8
V
DD
100 kΩ
C
1 kΩ
2
AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
–40°C to 85°C TPA0211DGN AEG
†
The DGN package are available taped and reeled. To order a taped and reeled part, add the
suffix R to the part number (e.g., TPA0211DGNR).
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MSOP
(DGN)
†
SYMBOLIZATION
I/O
DESCRIPTION
ST/MN
ST/MN
2-W MONO AUDIO POWER AMPLIFIER
SLOS275B – JANUARY 2000 – REVISED MARCH 2000
Terminal Functions
TERMINAL
NAME NO.
BYPASS 4 I
GND 7 GND is the ground connection.
IN 1 I IN is the audio input terminal.
SE/BTL 6 I
SHUTDOWN 2 I SHUTDOWN places the entire device in shutdown mode when held low. TTL compatible input.
V
DD
VO+ 5 O VO+ is the positive output for BTL and SE modes.
VO– 8 O VO– is the negative output in BTL mode and a high-impedance output in SE mode.
3 VDD is the supply voltage terminal.
BYPASS is the tap to the voltage divider for internal mid-supply bias. This terminal should be connected to
a 0.1-µF to 1-µF capacitor.
When SE/BTL is held low, the TPA0211 is in BTL mode. When SE/BTL is held high, the TPA0211 is in SE
mode.
TPA0211
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, VDD 6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, VI –0.3 V to VDD +0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation internally limited (see Dissipation Rating Table). . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, T
(see Table 3) –40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A
Operating junction temperature range, TJ –40°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
§
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
DGN 2.14 W
¶
Please see the Texas Instruments document,
(literature number SLMA002), for more information on the PowerPAD package. The thermal data was
measured on a PCB layout based on the information in the section entitled
Board for PowerPAD
TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C
¶
on page 33 of the before mentioned document.
17.1 mW/°C 1.37 W 1.11 W
PowerPAD Thermally Enhanced Package Application Report
T exas Instruments Recommended
recommended operating conditions
MIN MAX UNIT
Supply voltage, V
High-level input voltage, V
Low-level input voltage, V
Operating free-air temperature, T
DD
IH
IL
VDD = 3 V 2.7
VDD = 5 V 4.5
SHUTDOWN 2
VDD = 3 V 1.65
VDD = 5 V 2.75
SHUTDOWN 0.8
A
2.5
–40
5.5
85
V
V
V
°C
§
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
TPA0211
POOutput power, see Note 1
mW
POOutput power, see Note 1
2-W MONO AUDIO POWER AMPLIFIER
SLOS275B – JANUARY 2000 – REVISED MARCH 2000
electrical characteristics at specified free-air temperature, VDD = 3 V , TA = 25°C (unless otherwise
noted)
|VOO|
I
DD
I
DD(SD)
PARAMETER TEST CONDITIONS
Output offset voltage (measured differentially)
Supply current
Supply current, shutdown mode
MIN TYP MAX UNIT
30
mV
4
6
mA
1
10
µA
operating characteristics, VDD = 3 V, T
PARAMETER TEST CONDITIONS
p
p
THD + N
B
OM
NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz.
Total harmonic distortion plus noise
Maximum output power bandwidth
= 25°C, RL = 4 Ω
A
THD = 1%,
THD = 0.1%,
PO = 500 mW,
Gain = 2,
BTL mode
SE mode,
f = 20 Hz to 20 kHz
THD = 2%
RL = 32 Ω
MIN TYP MAX UNIT
660
33
0.3%
20
kHz
electrical characteristics at specified free-air temperature, VDD = 5 V , TA = 25°C (unless otherwise
noted)
PARAMETER TEST CONDITIONS
|VOO|
I
DD
I
DD(SD)
operating characteristics, VDD = 5 V, T
THD + N
B
OM
NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz.
Output offset voltage (measured differentially)
Supply current
Supply current, shutdown mode
= 25°C, RL = 4 Ω
A
PARAMETER TEST CONDITIONS
p
p
Total harmonic distortion plus
noise
Maximum output power bandwidth
THD = 1%,
THD = 0.1%,
PO = 1.5 W,
Gain = 2.5,
BTL mode
SE mode,
f = 20 Hz to 20 kHz
THD = 2%
RL = 32 Ω
MIN TYP MAX UNIT
30
mV
4
6
mA
1
10
µA
MIN TYP MAX UNIT
2
92
0.2%
20
W
mW
kHz
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPA0211
2-W MONO AUDIO POWER AMPLIFIER
SLOS275B – JANUARY 2000 – REVISED MARCH 2000
MECHANICAL DATA
DGN (S-PDSO-G8) PowerPAD PLASTIC SMALL-OUTLINE PACKAGE
0,65
8
1
1,07 MAX
3,05
2,95
0,38
0,25
5
3,05
2,95
4
Seating Plane
0,15
0,05
0,25
4,98
4,78
M
0,10
Thermal Pad
(See Note D)
0,15 NOM
0°–6°
Gage Plane
0,25
0,69
0,41
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions include mold flash or protrusions.
D. The package thermal performance may be enhanced by attaching an external heat sink to the thermal pad. This pad is electrically
and thermally connected to the backside of the die and possibly selected leads. The dimension of the thermal pad is 1.40 mm (height
as illustrated) × 1.80 (width as illustrated) mm (maximum). The pad is centered on the bottom of the package.
E. Falls within JEDEC MO-187
PowerPAD is a trademark of Texas Instruments Incorporated.
4073271/A 01/98
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5
IMPORTANT NOTICE
T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty . Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 2000, Texas Instruments Incorporated
Loading...