Datasheet TMX320LF2407PGEA, TMX320LF2406PZA, TMX320LF2402PGA Datasheet (Texas Instruments)

Download

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

D High-Performance Static CMOS Technology

– 33-ns Instruction Cycle Time (30 MHz) – 30 MIPS Performance – Low-Power 3.3-V Design

D Based on T320C2xx DSP CPU Core

– Code-Compatible With ’F243/’F241/’C242 – Instruction Set and Module Compatible

With ’F240/’C240

– Source-Code-Compatible With

TMS320C1x/2x

D Flash (LF) and ROM (LC) Device Options

– ’LF240x†: ’LF2407, ’LF2406, ’LF2402 – ’LC240x†: ’LC2406, ’LC2404, ’LC2402

D On-Chip Memory

– Up to 32K Words x 16 Bits of Flash

EEPROM (4 Sectors) or ROM

– Up to 2.5K Words x 16 Bits of

Data/Program RAM – 544 Words of Dual-Access (DARAM) – 2K Words of Single-Access (SARAM)

D Boot ROM (’LF240x Devices)

– SCI/SPI Flash Bootloader

D Two Event-Manager (EV) Modules (A and B)

EVA and EVB Each Include: – Two 16-Bit General-Purpose Timers – Eight 16-Bit Pulse-Width Modulation

(PWM) Channels Which Enable: – Three-Phase Inverter Control – Centered or Edge Alignment of PWM

Channels

– Emergency PWM Channel Shutdown

With External PDPINT

– Programmable Deadband Prevents

Shoot-Through Faults

– Three Capture Units For Time-Stamping

of External Events

– On-Chip Position Encoder Interface

Circuitry

– Synchronized Analog-to-Digital

Conversion

– Suitable for AC Induction, BLDC,

Switched Reluctance, and Stepper Motor Control

– Applicable for Multiple Motor and/or

Converter Control

D External Memory Interface (’LF2407)

– 192K Words x 16 Bits of Total Memory,

64K Program, 64K Data, 64K I/O

D Watchdog (WD) Timer Module D 10-Bit Analog-to-Digital Converter (ADC)

– 8 or 16 Multiplexed Input Channels – 500 ns Minimum Conversion Time – Selectable Twin 8-Input Sequencers

Triggered by Two Event Managers

D Controller Area Network (CAN) 2.0B Module D Serial Communications Interface (SCI) D 16-Bit Serial Peripheral Interface (SPI)

Module (Except ’x2402)

D Phase-Locked-Loop (PLL)-Based Clock

Generation

D Up to 40 Individually Programmable,

Multiplexed General-Purpose Input/Output (GPIO) Pins

D Five External Interrupts (Power Drive

Protection, Reset, and Two Maskable Interrupts)

D Power Management:

– Three Power-Down Modes – Ability to Power-Down Each Peripheral

Independently

D Real-Time JTAG-Compliant Scan-Based

Emulation, IEEE Standard 1149.1

‡

(JTAG)

D Development Tools Include:

– Texas Instruments (TI) ANSI

C Compiler, Assembler/Linker, and Code Composer Debugger

– Evaluation Modules – Scan-Based Self-Emulation (XDS510) – Numerous Third-Party Digital Motor

Control Support

D Package Options

– 144-Pin Thin Quad Flatpack (TQFP) PGE

(’LF2407)

– 100-Pin TQFP PZ (’LC2404, ’LC2406,

’LF2406)

– 64-Pin PQFP PG (’LC2402 and ’LF2402)

D Extended Temperature Options (A and S)

– A: – 40°C to 85°C – S: – 40°C to 125°C

ADVANCE

INFORMATION

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

TI, Code Composer, and XDS510 are trademarks of Texas Instruments Incorporated. †

Throughout this data sheet, ’240x is used as a generic name for the ’LF240x/’LC240x family of devices.

‡

IEEE Standard 1149.1–1990, IEEE Standard Test-Access Port

ADVANCE INFORMATION concerns new products in the sampling or preproduction phase of development. Characteristic data and other specifications are subject to change without notice.

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

Description 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TMS320x240x Device Summary 3. . . . . . . . . . . . . . . . . . .

Functional Block Diagram of the ’2407 DSP Controller 4

Pin Functions 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Memory Maps 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Peripheral Memory Map of the ’LF240x/’LC240x 21. . . .

Device Reset and Interrupts 22. . . . . . . . . . . . . . . . . . . . .

TMS320x240x Instruction Set 26. . . . . . . . . . . . . . . . . . . .

Functional Block Diagram

of the ’240x DSP CPU 27. . .

Peripherals 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Event Manager Modules (EVA, EVB) 36. . . . . . . . . . . .

Enhanced Analog-to-Digital Converter

(ADC) Module 40. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Controller Area Network (CAN) Module 41. . . . . . . . . .

Serial Communications Interface (SCI) Module 44. . . .

Serial Peripheral Interface (SPI) Module 46. . . . . . . . . .

PLL-Based Clock Module 48. . . . . . . . . . . . . . . . . . . . . .

Digital I/O and Shared Pin Functions 51. . . . . . . . . . . . .

External Memory Interface (’LF2407) 54. . . . . . . . . . . .

Watchdog (WD) Timer Module 55. . . . . . . . . . . . . . . . . .

Development Support 58. . . . . . . . . . . . . . . . . . . . . . . . . . .

Documentation Support 61. . . . . . . . . . . . . . . . . . . . . . . . .

Absolute Maximum Ratings 62. . . . . . . . . . . . . . . . . . . . . .

Recommended Operating Conditions 62. . . . . . . . . . . . .

Peripheral Register Description 90. . . . . . . . . . . . . . . . . . .

Mechanical Data 103. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

description

The TMS320LF240x and TMS320LC240x devices, new members of the ’24x family of digital signal processor (DSP) controllers, are part of the C2000 platform of fixed-point DSPs. The ’240x devices offer the enhanced TMS320 architectural design of the ’C2xx core CPU for low-cost, low-power, high-performance processing capabilities. Several advanced peripherals, optimized for digital motor and motion control applications, have been integrated to provide a true single chip DSP controller. While code-compatible with the existing ’24x DSP controller devices, the ’240x offers increased processing performance (30 MIPS) and a higher level of peripheral integration. See the TMS320x240x device summary section for device-specific features.

The ’240x family offers an array of memory sizes and different peripherals tailored to meet the specific price/performance points required by various applications. Flash-based devices of up to 32K words offer a reprogrammable solution useful for:

– Applications requiring field programmability upgrades – Development and initial prototyping of applications that migrate to ROM-based devices

Flash devices and corresponding ROM devices are fully pin-to-pin compatible. Note that flash-based devices contain a 256-word boot ROM to facilitate in-circuit programming.

All ’240x devices offer at least one event manager module which has been optimized for digital motor control and power conversion applications. Capabilities of this module include centered- and/or edge-aligned PWM generation, programmable deadband to prevent shoot-through faults, and synchronized analog-to-digital conversion. Devices with dual event managers enable multiple motor and/or converter control with a single ’240x DSP controller.

The high performance, 10-bit analog-to-digital converter (ADC) has a minimum conversion time of 500 ns and offers up to 16 channels of analog input. The auto sequencing capability of the ADC allows a maximum of 16 conversions to take place in a single conversion session without any CPU overhead.

A serial communications interface (SCI) is integrated on all devices to provide asynchronous communication to other devices in the system. For systems requiring additional communication interfaces; the ’2407, ’2406, and ’2404 offer a 16-bit synchronous serial peripheral interface (SPI). The ’2407 and ’2406 offer a controller area network (CAN) communications module that meets 2.0B specifications. To maximize device flexibility, functional pins are also configurable as general purpose inputs/outputs (GPIO).

To streamline development time, JTAG-compliant scan-based emulation has been integrated into all devices. This provides non-intrusive real-time capabilities required to debug digital control systems. A complete suite of code generation tools from C compilers to the industry-standard Code Composer debugger supports this family. Numerous third party developers not only offer device-level development tools, but also system-level design and development support.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

TMS320x240x device summary

Note that throughout this data sheet, ’240x is used as a generic name for the ’LF240x/’LC240x family of devices.

Table 1. Hardware Features of ’240x Devices

FEATURE ’LF2407

†

’LF2406 ’LF2402 ’LC2406 ’LC2404 ’LC2402

’C2xx DSP Core Yes Yes Yes Yes Yes Yes Instruction Cycle 33 ns 33 ns 33 ns 33 ns 33 ns 33 ns MIPS (30 MHz) 30 MIPS 30 MIPS 30 MIPS 30 MIPS 30 MIPS 30 MIPS

DARAM 544 544 544 544 544 544

RAM (16-bit word)

SARAM 2K 2K — 2K 1K —

On-chip Flash (16-bit word) (4 sectors: 4K, 12K, 12K, 4K)

32K 32K 8K — — —

On-chip ROM (16-bit word) — — — 32K 16K 4K Boot ROM (16-bit word) 256 256 256 — — — External Memory Interface Yes — — — — — Event Managers A and B

(EVA and EVB)

EVA, EVB EVA, EVB EVA EVA, EVB EVA, EVB EVA

S General-Purpose (GP) Timers 4 4 2 4 4 2 S Compare (CMP)/PWM 10/16 10/16 5/8 10/16 10/16 5/8 S Capture (CAP)/QEP 6/4 6/4 3/2 6/4 6/4 3/2

Watchdog Timer Yes Yes Yes Yes Yes Yes 10-Bit ADC Yes Yes Yes Yes Yes Yes

S Channels 16 16 8 16 16 8 S Conversion Time (minimum) 500 ns 500 ns 500 ns 500 ns 500 ns 500 ns

SPI Yes Yes — Yes Yes — SCI Yes Yes Yes Yes Yes Yes CAN Yes Yes — Yes — — Digital I/O Pins (Shared) 41 41 21 41 41 21 External Interrupts 5 5 3 5 5 3 Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V Packaging 144 TQFP 100 TQFP 64 PQFP 100 TQFP 100 TQFP 64 PQFP

†

’LF2407, the full-featured device of the ’LF240x family of DSP controllers, is useful for emulation and code development.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

functional block diagram of the ’2407 DSP controller

XTAL1/CLKIN XTAL2

PLLV

CCA

PLLF2

PLLF

SSA

REFHI

ADCIN08–ADCIN15 V

CCA

ADCIN00–ADCIN07

SCIRXD/IOPA1 SPISIMO/IOPC2

XINT2/ADCSOC/IOPD0 SCITXD/IOPA0

REFLO

CCP

(5V)

Port A(0–7) IOPA[0:7]

SPICLK/IOPC4 SPISTE/IOPC5

SPISOMI/IOPC3

Port E(0–7) IOPE[0:7] Port F(0–6) IOPF[0:6]

Port C(0–7) IOPC[0:7] Port D(0) IOPD[0]

Port B(0–7) IOPB[0:7]

TDO TDI

CANRX/IOPC7

TRST

CANTX/IOPC6

EMU1 PDPINTB

TCK EMU0

TMS

CAP5/QEP4/IOPF0

CAP4/QEP3/IOPE7

PWM7/IOPE1 PWM8/IOPE2

CAP6/IOPF1

PWM10/IOPE4

PWM9/IOPE3

PWM11/IOPE5 PWM12/IOPE6

T4PWM/T4CMP/IOPF3

T3PWM/T3CMP/IOPF2

TDIRB/IOPF4 TCLKINB/IOPF5

DARAM (B0)

256 Words

DARAM (B1)

256 Words

DARAM (B2)

32 Words

’C2xx

DSP Core

PLL Clock

10-Bit ADC

(With Twin

Autosequencer)

CLKOUT/IOPE0

XINT1/IOPA2

XINT2/ADCSOC/IOPD0

BIO/IOPC1

MP/MC

TMS2

A0–A15 D0–D15

TP1 TP2

BOOT_EN/XF

READY

STRB

R/W

PS, DS, IS

VIS_OE

ENA_144

CAP3/IOPA5

PWM1/IOPA6

CAP1/QEP1/IOPA3 CAP2/QEP2/IOPA4

PDPINTA

PWM5/IOPB2 PWM6/IOPB3

PWM3/IOPB0 PWM4/IOPB1

PWM2/IOPA7

T2PWM/T2CMP/IOPB5

T1PWM/T1CMP/IOPB4

TCLKINA/IOPB7

TDIRA/IOPB6

VDD (3.3 V)

CCP

(5V)

SARAM (2K Words)

Flash/ROM

(32K Words:

4K/12K/12K/4K)

External Memory Interface

Event Manager A

D 3 × Capture Input D 6 × Compare/PWM

Output D 2 × GP Timers/PWM

SCI

SPI

Digital I/O

(Shared With Other Pins)

CAN

JTAG Port

Event Manager B

D 3 × Capture Input D 6 × Compare/PWM

Output D 2 × GP Timers/PWM

Indicates optional modules The memory size and peripheral selection of these modules change for different ’240x devices. See Table 1 for device-specific details.

W/R / IOPC0

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

144

143

142

141

140

139

138

137

136

135

134RS133

132

131

130

129

128

127

126

125

124

123

122

121

120

119

118

117

116

115

114

113

112

373839404142434445464748495051525354555657585960616263646566676869

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

108 107 106 105 104 103 102 101 100

99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73

111

110

109

707172

TMS320LF2407

PDPINTA

PLLF

TDIRA/

IOPB6

XINT2/ADCSOC/

IOPD0

CLKOUT

/IOPE0

PDPINTB

XTAL1/CLKIN

XTAL2

PLLV

CCA

PLLF2

BOOT_EN/XF

CCP

TP1

TP2

IOPF6

EMU0

EMU1/OFF

TCK

TDI

TDO

TMS

TMS2

TRST

R/W

W/R

/IOPC0

STRB

READY

MP/MC

ENA_144

VIS_OE

A10

A11

A12

A13

A14

A15

D10

D11

D12

D13

D14

D15

PLLV

CCA

DDO

SSO

CAP1/QEP1/

IOPA3

CAP2/QEP2/

IOPA4

CAP3/

IOPA5

PWM1/

PWM2/

PWM3/

PWM4/

PWM5/

PWM6/

T1PWM/T1CMP/

IOPB4

T2PWM/T2CMP/

IOPB5

TCLKINA/

CAP4/QEP3/

IOPE7

CAP5/QEP4/

IOPF0

CAP6/

PWM7/

PWM8/

PWM9/

PWM10/

PWM11/

PWM12/

T3PWM/T3CMP/

IOPF2

T4PWM/T4CMP/

IOPF3

TDIRB/

IOPF4

TCLKINB/

ADCIN00

ADCIN01

ADCIN02

ADCIN03

ADCIN04 ADCIN05

ADCIN06 ADCIN07

ADCIN08

ADCIN09

ADCIN10

ADCIN11

ADCIN12

ADCIN13

ADCIN14

ADCIN15

REFHI

REFLO

CCA

SSA

CANRX/

CANTX/

SCITXD/

IOPA0

SCIRXD/

IOPA1

SPICLK/

IOPC4

SPISIMO/

IOPC2

SPISOMI/

IOPC3

SPISTE/

IOPC5

XINT1/

IOPA2

†

Bold, italicized pin names

indicate pin function after reset.

‡

BOOT_EN

is available only on flash devices.

IOPB7

IOPE6

IOPB3

IOPB2

IOPE5

IOPB1

IOPB0

IOPA7

IOPE4

IOPA6

IOPE3

IOPE2

IOPE1

IOPF1

IOPC7

IOPC6

IOPF5

IOPC1

BIO/

PGE PACKAGE

†

(TOP VIEW)

‡

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

SCIRXD/

TMS

TDO

DDO

SSO

TDI

PDPINTB

TCK

IOPF6

TCLKINB/

IOPF5

XTAL2

XTAL1/CLKIN

BOOT_EN

/XF

BIO

/IOPC1

SSA

CCA

REFHI

REFLO

ADCIN08

ADCIN00

ADCIN09

ADCIN01

ADCIN10

TCLKINA/

IOPB7

PWM12/

IOPE6

PWM6/

IOPB3

SSO

DDO

PWM5/

IOPB2

PWM11/

IOPE5

PWM4/

IOPB1

PWM3/

IOPB0

PWM2/

IOPA7

PWM10/

IOPE4

PWM1/

IOPA6

CCP

PWM9/

IOPE3

TP1

PWM8/

IOPE2

TP2

PWM7/

IOPE1

SSO

DDO

CAP6/

IOPF1

CANRX/

IOPC7

‡

CANTX/

IOPC6

‡

50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26100

25242322212019181716151413121110987654321

51525354555657585960616263646566676869707172737475

ADCIN11

ADCIN02

ADCIN12

ADCIN03

ADCIN13

ADCIN04

ADCIN05

ADCIN14

ADCIN06

ADCIN07

ADCIN15

EMU1/

EMU0

CAP4/QEP3/VCAP1/QEP1/

CAP5/QEP4/

CAP2/QEP2/VCAP3/

/IOPE0

DDO

TRST

TDIRB/

T4PWM/T4CMP/

PDPINTA

PLLF2

PLLF

T1PWM/T1CMP/

T2PWM/T2CMP/

XINT2/ADCSOC/

SCITXD/

SPISOMI/

SPISTE/

SPICLK/

DDO

PZ PACKAGE

†

(TOP VIEW)

TDIRA/

TMS320LC2404 TMS320LC2406 TMS320LF2406

T3PWM/T3CMP/

XINT1/

PLLV

CCA

TMS2

DDO

SSOVSSO

SSO

†

Bold, italicized pin names

indicate pin function after reset.

‡

CANTX and CANRX are not available on ’LC2404 devices.

BOOT_EN

is available only on flash devices.

IOPF4

IOPF3

IOPF2

IOPB6

IOPB4

IOPB5

IOPC0

IOPD0

IOPA2

IOPA0

IOPA1

SPISIMO/

IOPC2

IOPC3

IOPC5

IOPC4

IOPE7

CLKOUT

IOPA3

IOPF0

IOPA4

IOPA5

TDIRB/

IOPF4

OFF

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

REFHI

CCA

SSA

BOOT_EN

/XF

‡

XTAL1/CLKIN

XTAL2

TCK

TDI

TDO

TMS

DDO

IOPC6

IOPC7

TP2

TP1

CCP

PWM1

PWM2

PWM3

PWM4

PWM5

ADCIN00

PDPINTA

PLLF2

PLLF

T1PWM/T1CMP/

T2PWM/T2CMP/

SCITXD/

EMU0

TMS2

TCLKINA/

PWM6/

CAP1/QEP1/

CAP2/QEP2/

CAP3/

CLKOUT

ADCIN01

ADCIN02

ADCIN03

ADCIN04

ADCIN05

ADCIN06

ADCIN07

REFLO

SCIRXD/

XINT2/ADCSOC/

PLLV

CCA

EMU1/

TRST

TMS320LC2402 TMS320LF2402

SSO

DDO

SSO

VDDV

IOPB4

IOPB5

IOPD0

IOPA0

IOPA1

IOPC2

IOPC3

IOPC4

IOPB7

IOPB3

/IOPE0

IOPA5

IOPA4

IOPA3

OFF

191 2 3 4 5 6 7 8 9101112131415161718

3351 343550 49 48 47 46 45 44 43 42 41 40 3938 37 36

53 54 55

56 57

58 59 60 61 62

31 30

29 28 27 26 25 24 23 22 21

PG PACKAGE

†

(TOP VIEW)

†

Bold, italicized pin names

indicate pin function after reset.

‡

BOOT_EN

is available only on flash devices.

SSO

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

pin functions

The TMS320LF2407 device is the superset of all the ’240x devices. All signals are available on the ’2407 device. Table 2 lists the key signals available in the ’240x family of devices.

Table 2. ’LF240x and ’LC240x Pin List and Package Options

†‡

PIN NAME ’LF2407 ’2406 ’LC2404 ’2402 DESCRIPTION

EVENT MANAGER A (EVA)

CAP1/QEP1/

IOPA3

83 57 57 4

Capture input #1/quadrature encoder pulse input #1 (EVA) or GPIO (↑)

CAP2/QEP2/

IOPA4

79 55 55 3

Capture input #2/quadrature encoder pulse input #2 (EVA) or GPIO (↑)

CAP3/

IOPA5

75 52 52 2 Capture input #3 (EVA) or GPIO (↑)

PWM1/

IOPA6

56 39 39 59

Compare/PWM output pin #1 (EVA) or GPIO (↑)

PWM2/

IOPA7

54 37 37 58

Compare/PWM output pin #2 (EVA) or GPIO (↑)

PWM3/

IOPB0

52 36 36 57

Compare/PWM output pin #3 (EVA) or GPIO (↑)

PWM4/

IOPB1

47 33 33 54

Compare/PWM output pin #4 (EVA) or GPIO (↑)

PWM5/

IOPB2

44 31 31 53

Compare/PWM output pin #5 (EVA) or GPIO (↑)

PWM6/

IOPB3

40 28 28 50 Compare/PWM output pin #6 (EVA) or GPIO (↑)

T1PWM/T1CMP/

IOPB4

16 12 12 40 Timer 1 compare output (EVA) or GPIO (↑)

T2PWM/T2CMP/

IOPB5

18 13 13 41 Timer 2 compare output (EVA) or GPIO (↑)

TDIRA/

IOPB6

14 11 11

Counting direction for general-purpose (GP) timer (EVA) or GPIO. If TDIRA=1, upward counting is selected. If TDIRA=0, downward counting is selected. (↑)

TCLKINA/

IOPB7

37 26 26 49

External clock input for GP timer (EVA) or GPIO. Note that timer can also use the internal device clock. (↑)

EVENT MANAGER B (EVB)

CAP4/QEP3/

IOPE7

88 60 60

Capture input #4/quadrature encoder pulse input #3 (EVB) or GPIO (↑)

CAP5/QEP4/

IOPF0

81 56 56

Capture input #5/quadrature encoder pulse input #4 (EVB) or GPIO (↑)

CAP6/

IOPF1

69 48 48 Capture input #6 (EVB) or GPIO (↑)

PWM7/

IOPE1

65 45 45 Compare/PWM output pin #7 (EVB) or GPIO (↑)

PWM8/

IOPE2

62 43 43 Compare/PWM output pin #8 (EVB) or GPIO (↑)

PWM9/

IOPE3

59 41 41 Compare/PWM output pin #9 (EVB) or GPIO (↑)

PWM10/

IOPE4

55 38 38 Compare/PWM output pin #10 (EVB) or GPIO (↑)

PWM11/

IOPE5

46 32 32 Compare/PWM output pin #11 (EVB) or GPIO (↑)

PWM12/

IOPE6

38 27 27 Compare/PWM output pin #12 (EVB) or GPIO (↑)

T3PWM/T3CMP/

IOPF2

8 7 7 Timer 3 compare output (EVB) or GPIO (↑)

T4PWM/T4CMP/

IOPF3

6 5 5 Timer 4 compare output (EVB) or GPIO (↑)

TDIRB/

IOPF4

2 2 2

Counting direction for general-purpose (GP) timer (EVB) or GPIO. If TDIRB=1, upward counting is selected. If TDIRB=0, downward counting is selected. (↑)

TCLKINB/

IOPF5

126 89 89

External clock input for GP timer (EVB) or GPIO. Note that timer can also use the internal device clock. (↑)

†

Bold, italicized pin names

indicate pin function after reset.

‡

GPIO – General-purpose input/output pin. All GPIOs come up as input after reset.

Pin changes with respect to SPRS094B data sheet. LEGEND: ↑ – Internal pullup ↓ – Internal pulldown

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

pin functions (continued)

Table 2. ’LF240x and ’LC240x Pin List and Package Options†‡ (Continued)

PIN NAME ’LF2407 ’2406 ’LC2404 ’2402 DESCRIPTION

ANALOG-TO-DIGITAL CONVERTER (ADC)

ADCIN00 112 79 79 18 Analog input #0 to the ADC ADCIN01 110 77 77 17 Analog input #1 to the ADC ADCIN02 107 74 74 16 Analog input #2 to the ADC ADCIN03 105 72 72 15 Analog input #3 to the ADC ADCIN04 103 70 70 14 Analog input #4 to the ADC ADCIN05 102 69 69 13 Analog input #5 to the ADC ADCIN06 100 67 67 12 Analog input #6 to the ADC ADCIN07 99 66 66 11 Analog input #7 to the ADC ADCIN08 113 80 80 Analog input #8 to the ADC ADCIN09 111 78 78 Analog input #9 to the ADC ADCIN10 109 76 76 Analog input #10 to the ADC ADCIN11 108 75 75 Analog input #11 to the ADC ADCIN12 106 73 73 Analog input #12 to the ADC ADCIN13 104 71 71 Analog input #13 to the ADC ADCIN14 101 68 68 Analog input #14 to the ADC ADCIN15 98 65 65 Analog input #15 to the ADC V

REFHI

115 82 82 20 ADC analog high-voltage reference input

REFLO

114 81 81 19 ADC analog low-voltage reference input

CCA

116 83 83 21

Analog supply voltage for ADC (3.3 V). V

CCA

must

be isolated from digital supply voltage.

SSA

117 84 84 22 Analog ground reference for ADC

CONTROLLER AREA NETWORK (CAN), SERIAL COMMUNICATIONS INTERFACE (SCI), SERIAL PERIPHERAL INTERFACE (SPI)

CANRX 70 49 – –

CANRX/

IOPC7

IOPC7 70 49 49 63

CAN receive data or GPIO (↑)

CANTX 72 50 – –

CANTX/

IOPC6

IOPC6 72 50 50 64

CAN transmit data or GPIO (↑)

SCITXD/

IOPA0

25 17 17 43

SCI asynchronous serial port transmit data or GPIO (↑)

SCIRXD/

IOPA1

26 18 18 44

SCI asynchronous serial port receive data or or GPIO (↑)

SPICLK 35 24 24 –

SPICLK/

IOPC4

IOPC4 35 24 24 47

SPI clock or GPIO (↑)

SPISIMO 30 21 21 –

SPISIMO/

IOPC2

IOPC2 30 21 21 45

SPI slave in, master out or GPIO (↑)

SPISOMI 32 22 22 –

SPISOMI/

IOPC3

IOPC3 32 22 22 46

SPI slave out, master in or GPIO (↑)

SPISTE 33 23 23 –

SPISTE/

IOPC5

IOPC5 33 23 23 –

SPI slave transmit enable (optional) or GPIO (↑)

†

Bold, italicized pin names

indicate pin function after reset.

‡

GPIO – General-purpose input/output pin. All GPIOs come up as input after reset. LEGEND: ↑ – Internal pullup ↓ – Internal pulldown

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

pin functions (continued)

Table 2. ’LF240x and ’LC240x Pin List and Package Options†‡ (Continued)

PIN NAME ’LF2407 ’2406 ’LC2404 ’2402 DESCRIPTION

EXTERNAL INTERRUPTS, CLOCK

RS 133 93 93 28

Device reset. RS causes the ’240x to terminate execution and sets PC = 0. When RS

is brought to a high level, execution begins at location zero of program memory. RS

affects (or sets to zero) various registers and status bits. When the watchdog timer overflows, it initiates a system reset pulse that is reflected on the RS

pin. (↑)

PDPINTA 7 6 6 36

Power drive protection interrupt input. This interrupt, when activated, puts the PWM output pins (EVA) in the high-impedance state should motor drive/power converter abnormalities, such as overvoltage or overcurrent, etc., arise. PDPINTA

is a

falling-edge-sensitive interrupt. (↑)

XINT1/

IOPA2

23 16 16

External user interrupt 1 or GPIO. Both XINT1 and XINT2 are edge-sensitive. The edge polarity is programmable. (↑)

XINT2/ADCSOC/

IOPD0

21 15 15 42

External user interrupt 2 and ADC start of conversion or GPIO. External “start-of-conversion” input for ADC/GPIO. Both XINT1 and XINT2 are edge-sensitive. The edge polarity is programmable. (↑)

CLKOUT

/IOPE0 73 51 51 1

Clock output or GPIO. This pin outputs either the CPU clock (CLKOUT) or the watchdog clock (WDCLK). The selection is made by the CLKSRC bit (bit 14) of the System Control and Status Register (SCSR). This pin can be used as a GPIO if not used as a clock output pin. (↑)

PDPINTB 137 95 95

Power drive protection interrupt input. This interrupt, when activated, puts the PWM output pins (EVB) in the high-impedance state should motor drive/power converter abnormalities, such as overvoltage or overcurrent, etc., arise. PDPINT

is a

falling-edge-sensitive interrupt. (↑)

OSCILLATOR, PLL, FLASH, BOOT, AND MISCELLANEOUS

XTAL1/CLKIN 123 87 87 24

PLL oscillator input pin. Crystal input to PLL/clock source input to PLL. XTAL1/CLKIN is tied to one side of a reference crystal.

XTAL2 124 88 88 25

Crystal output. PLL oscillator output pin. XTAL2 is tied to one side of a reference crystal. This pin goes in the high-impedance state when EMU1/OFF

is active low. PLLF 11 9 9 38 Filter input 1 PLLV

CCA

12 10 10 39 PLL supply (3.3 V)

PLLF2 10 8 8 37 Filter input 2

BOOT_EN 121 86 – 23

Boot ROM enable, GPO, XF. This pin will be sampled as input (BOOT_EN

) to update SCSR2.3 (BOOT_EN

BOOT_EN / XF

XF 121 86 86 23

bit) during reset and then driven as an output signal for XF. ROM devices do not have boot ROM, hence, no BOOT_EN modes. (↑)

†

Bold, italicized pin names

indicate pin function after reset.

‡

GPIO – General-purpose input/output pin. All GPIOs come up as input after reset. LEGEND: ↑ – Internal pullup ↓ – Internal pulldown

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

pin functions (continued)

Table 2. ’LF240x and ’LC240x Pin List and Package Options†‡ (Continued)

PIN NAME ’LF2407 ’2406 ’LC2404 ’2402 DESCRIPTION

OSCILLATOR, PLL, FLASH, BOOT, AND MISCELLANEOUS (CONTINUED)

CCP

(5V) 58 40 40 60

Flash programming voltage pin. This is the 5-V supply used for flash programming. Flash cannot be programmed if this pin is held at 0 V . Connect to 5-V supply for programming or tie it to GND during functional mode.

TP1 (Flash) 60 42 42 61

Flash array test pin.

Do not connect.

TP2 (Flash) 63 44 44 62

Flash array test pin

. Do not connect.

IOPF6 131 92 92 General-purpose I/O (↑)

BIO

/IOPC1 119 85 85

Branch control input. BIO is polled by the BCND pma,BIO instruction. If BIO

is low, a branch is executed. If BIO is not used, it should be pulled high. This pin is configured as a branch control input by all device resets. It can be used as a GPIO, if not used as a branch control input. (↑)

EMULATION AND TEST

EMU0 90 61 61 7

Emulator I/O #0 with internal pullup. When TRST is driven high, this pin is used as an interrupt to or from the emulator system and is defined as input/output through the JTAG scan. (↑)

EMU1/OFF 91 62 62 8

Emulator pin 1. Emulator pin 1 disables all outputs. When TRST is driven high, EMU1/OFF is used as an interrupt to or from the emulator system and is defined as an input/output through the JTAG scan. When TRST

is driven low, this pin is configured as

OFF

. EMU1/OFF, when active low, puts all output drivers in the

high-impedance state. Note that OFF

is used exclusively for testing and emulation purposes (not for multiprocessing applications). Therefore, for the OFF

condition, the following apply: TRST

= 0 EMU0 = 1 EMU1/OFF

= 0

TCK 135 94 94 29 JTAG test clock with internal pullup (↑)

TDI 139 96 96 30

JTAG test data input (TDI) with internal pullup. TDI is clocked into the selected register (instruction or data) on a rising edge of TCK. (↑)

TDO 142 99 99 31

JTAG scan out, test data output (TDO). The contents of the selected register (instruction or data) is shifted out of TDO on the falling edge of TCK. (↓)

TMS 144 100 100 32

JTAG test-mode select (TMS) with internal pullup. This serial control input is clocked into the TAP controller on the rising edge of TCK. (↑)

TMS2 36 25 25 48

JTAG test-mode select 2 (TMS) with internal pullup. This serial control input is clocked into the TAP controller on the rising edge of TCK. Used for test and emulation only. (↑)

TRST 1 1 1 33

JTAG test reset with internal pulldown. TRST, when driven high, gives the scan system control of the operations of the device. If this signal is not connected or driven low, the device operates in its functional mode, and the test reset signals are ignored. (↓)

†

Bold, italicized pin names

indicate pin function after reset.

‡

GPIO – General-purpose input/output pin. All GPIOs come up as input after reset.

Pin changes with respect to SPRS094B data sheet. LEGEND: ↑ – Internal pullup ↓ – Internal pulldown

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

pin functions (continued)

Table 2. ’LF240x and ’LC240x Pin List and Package Options†‡ (Continued)

PIN NAME ’LF2407 ’2406 ’LC2404 ’2402 DESCRIPTION

ADDRESS, DATA, AND MEMORY CONTROL SIGNALS

DS 87

Data space strobe. IS, DS, and PS are always high

unless low-level asserted for access to the relevant

external memory space or I/O. They are placed in the

high-impedance state during reset, power down, and

when EMU1/OFF

is active low.

IS 82

I/O space strobe. IS, DS, and PS are always high

unless low-level asserted for access to the relevant

external memory space or I/O. They are placed in the

high-impedance state during reset, power down, and

when EMU1/OFF

is active low.

PS 84

Program space strobe. IS, DS, and PS are always

high unless low-level asserted for access to the

relevant external memory space or I/O. They are

placed in the high-impedance state during reset,

power down, and when EMU1/OFF

is active low.

R/W 92

Read/write qualifier signal. R/W indicates transfer

direction during communication to an external device.

It is normally in read mode (high), unless low level is

asserted for performing a write operation. It is placed

in the high-impedance state when EMU1/OFF

active low and during power down.

W/R

Write/Read qualifier or GPIO. This is an inverted R/W

signal useful for zero-wait-state memory interface. It

W/R

/ IOPC0

IOPC0 19 14 14

is normally low, unless a memory write operation is

performed. See Table 13, Port C section, for reset

note regarding ’LF2406 and ’LF2402. (↑)

RD 93

Read enable strobe. Read-select indicates an active,

external read cycle. RD

is active on all external

program, data, and I/O reads. RD

goes into the

high-impedance state when EMU1/OFF

is active low.

WE 89

Write enable strobe. The falling edge of WE indicates

that the device is driving the external data bus

(D15–D0). WE

is active on all external program,

data, and I/O writes. WE

goes in the high-impedance

state when EMU1/OFF

is active low.

STRB 96

External memory access strobe. STRB is always high

unless asserted low to indicate an external bus cycle.

STRB

is active for all off-chip accesses. It is placed in the high-impedance state during power down, and when EMU1/OFF

is active low.

READY 120

READY is pulled low to add wait states for external accesses. READY indicates that an external device is prepared for a bus transaction to be completed. If the device is not ready, it pulls the READY pin low. The processor waits one cycle and checks READY again. Note that the processor performs READY -detection if at least one software wait state is programmed. To meet the external READY timings, the wait-state generator control register (WSGR) should be programmed for at least one wait state. (↑)

†

Bold, italicized pin names

indicate pin function after reset.

‡

GPIO – General-purpose input/output pin. All GPIOs come up as input after reset. LEGEND: ↑ – Internal pullup ↓ – Internal pulldown

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

pin functions (continued)

Table 2. ’LF240x and ’LC240x Pin List and Package Options†‡ (Continued)

PIN NAME ’LF2407 ’2406 ’LC2404 ’2402 DESCRIPTION

ADDRESS, DATA, AND MEMORY CONTROL SIGNALS (CONTINUED)

MP/MC 118

Microprocessor/Microcomputer mode select. If this pin is low during reset, the device is put in microcomputer mode and program execution begins at 0000h of internal program memory (flash EEPROM). A high value during reset puts the device in microprocessor mode and program execution begins at 0000h of external program memory. This line sets the MP/MC

bit (bit 2 in

the SCSR2 register). (↓)

ENA_144 122

Active high to enable external interface signals. If pulled low, the ’2407 behaves like the ’2406/’2404—i.e., it has no external memory and generates an illegal address if any of the three external spaces are accessed (IS

and DS asserted). This pin

has an internal pulldown. (↓)

VIS_OE 97

Visibility output enable (active when data bus is output). This pin is active (low) whenever the external databus is driving as an output during visibility mode. Can be used by external decode logic to prevent data bus contention while running in visibility

mode. A0 80 Bit 0 of the 16-bit address bus A1 78 Bit 1 of the 16-bit address bus A2 74 Bit 2 of the 16-bit address bus A3 71 Bit 3 of the 16-bit address bus A4 68 Bit 4 of the 16-bit address bus A5 64 Bit 5 of the 16-bit address bus A6 61 Bit 6 of the 16-bit address bus A7 57 Bit 7 of the 16-bit address bus A8 53 Bit 8 of the 16-bit address bus A9 51 Bit 9 of the 16-bit address bus A10 48 Bit 10 of the 16-bit address bus A11 45 Bit 11 of the 16-bit address bus A12 43 Bit 12 of the 16-bit address bus A13 39 Bit 13 of the 16-bit address bus A14 34 Bit 14 of the 16-bit address bus A15 31 Bit 15 of the 16-bit address bus D0 127 Bit 0 of 16-bit data bus (↑) D1 130 Bit 1 of 16-bit data bus (↑) D2 132 Bit 2 of 16-bit data bus (↑) D3 134 Bit 3 of 16-bit data bus (↑) D4 136 Bit 4 of 16-bit data bus (↑) D5 138 Bit 5 of 16-bit data bus (↑) D6 143 Bit 6 of 16-bit data bus (↑) D7 5 Bit 7 of 16-bit data bus (↑) D8 9 Bit 8 of 16-bit data bus (↑)

†

Bold, italicized pin names

indicate pin function after reset.

‡

GPIO – General-purpose input/output pin. All GPIOs come up as input after reset. LEGEND: ↑ – Internal pullup ↓ – Internal pulldown

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

pin functions (continued)

Table 2. ’LF240x and ’LC240x Pin List and Package Options†‡ (Continued)

PIN NAME ’LF2407 ’2406 ’LC2404 ’2402 DESCRIPTION

ADDRESS, DATA, AND MEMORY CONTROL SIGNALS (CONTINUED)

D9 13 Bit 9 of 16-bit data bus (↑) D10 15 Bit 10 of 16-bit data bus (↑) D11 17 Bit 11 of 16-bit data bus (↑) D12 20 Bit 12 of 16-bit data bus (↑) D13 22 Bit 13 of 16-bit data bus (↑) D14 24 Bit 14 of 16-bit data bus (↑) D15 27 Bit 15 of 16-bit data bus (↑)

POWER SUPPLY

29 20 20 6 50 35 35 27

86 59 59 56

Core supply +3.3 V . Digital logic supply voltage.

129 91 91

4 4 4 10 42 30 30 35 67 47 47 52

DDO

77 54 54

I/O buffer supply +3.3 V. Digital logic and buffer supply voltage.

95 64 64

141 98 98

28 19 19 5 49 34 34 26

85 58 58 55

Core ground. Digital logic ground reference.

128 90 90

3 3 3 9 41 29 29 34 66 46 46 51

SSO

76 53 53

I/O buffer ground. Digital logic and buffer ground reference.

SSO

94 63 63

I/O buffer ground. Digital logic and buffer ground reference.

125 97 97 140

†

Bold, italicized pin names

indicate pin function after reset.

‡

GPIO – General-purpose input/output pin. All GPIOs come up as input after reset.

Pin changes with respect to SPRS094B data sheet. LEGEND: ↑ – Internal pullup ↓ – Internal pulldown

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

memory maps – ’LF2407

Reserved

0000

003F

Hex Program

Interrupt Vectors

On-Chip Flash Memory (Sectored) – if MP/MC = 0 External Program Memory – if MP/MC

= 1

7FFF

8000

0000 005F

0060

Hex Data

Memory-Mapped

Registers/Reserved Addresses

007F 0080

On-Chip DARAM B2

01FF

Reserved

02FF 0300

On-Chip DARAM (B0)‡ (CNF = 0)

Reserved (CNF = 1)

03FF 0400

On-Chip DARAM (B1)

07FF 0800

Reserved

6FFF

7000

Reserved

Peripheral Memory-Mapped Registers (System, WD, ADC, SCI, SPI, CAN, I/O, Interrupts)

7FFF

8000

External

0000

Hex I/O

FEFF

FF00

FF0E

FF0F

Reserved

External

FFFF

FEFF

FF00

Reserved† (CNF = 1)

External (CNF = 0)

FDFF FE00

External

On-Chip DARAM (B0)† (CNF = 1)

External (CNF = 0)

FFFF

FFFE

Wait-State Generator Control

FF10

Flash Control Mode Register

(Only for Flash Devices)

SARAM (See Table 1 for details.)

FFFF

SARAM (2K) (PON = 1)

Internal

External (PON=0)

87FF 8800

0FFF

FLASH SECTOR 0 (4K)

1000

3FFF

FLASH SECTOR 1 (12K)

FLASH SECTOR 2 (12K)

FLASH SECTOR 3 (4K)

4000

6FFF

7000

0FFF 1000

0200

SARAM (2K) (DON = 1)

Internal

External (DON=0)

0040

NOTE A: Boot ROM: If the boot ROM is enabled, then address 0000–00FF in the program space will be occupied by boot ROM. †

When CNF = 1, addresses FE00h–FEFFh and FF00h–FFFFh are mapped to the same physical block (B0) in program-memory space. For example, a write to FE00h has the same effect as a write to FF00h. For simplicity, addresses FE00h–FEFFh are referred to as reserved when CNF = 1.

‡

When CNF = 0, addresses 0100h–01FFh and 0200h–02FFh are mapped to the same physical block (B0) in data-memory space. For example, a write to 0100h has the same effect as a write to 0200h. For simplicity , addresses 0100h–01FFh are referred to as reserved.

Addresses 0300h–03FFh and 0400h–04FFh are mapped to the same physical block (B1) in data-memory space. For example, a write to 0400h has the same effect as a write to 0300h. For simplicity , addresses 0400h–04FFh are referred to as reserved.

Figure 1. TMS320LF2407 Memory Map

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

memory maps (continued) – ’LF2406

Reserved

On-Chip Flash Memory (Sectored)

0000 005F

0060

Hex Data

Memory-Mapped

Registers/Reserved Addresses

007F 0080

On-Chip DARAM B2

01FF

0200

Reserved

02FF

0300

On-Chip DARAM (B0)‡ (CNF = 0)

Reserved (CNF = 1)

03FF

0400

On-Chip DARAM (B1)

07FF

0800

Reserved

SARAM (2K) (DON = 1)

Internal

Reserved (DON = 0)

6FFF

7000

Reserved

Peripheral Memory-Mapped

Registers (System, WD, ADC,

SCI, SPI, CAN, I/O, Interrupts)

7FFF

8000

Reserved

0000

Hex I/O

FEFF

FF00

FF0E

FF0F

Reserved

FFFF

FFFE

Reserved

FF10

Flash Control Mode Register

(Only for Flash devices)

SARAM (See Table 1 for details.)

FFFF

0FFF

1000

0000

003F

Hex Program

Interrupt Vectors

7FFF 8000

FFFF

FEFF FF00

Reserved† (CNF = 1)

External (CNF = 0)

FDFF FE00

On-Chip DARAM (B0)† (CNF = 1)

External (CNF = 0)

SARAM (2K) (PON = 1)

Internal

External (PON=0)

87FF

8800

0FFF

FLASH SECTOR 0 (4K)

1000

3FFF

FLASH SECTOR 1 (12K)

FLASH SECTOR 2 (12K)

FLASH SECTOR 3 (4K)

4000

6FFF

7000

Reserved

0040

NOTE A: Boot ROM: If the boot ROM is enabled, then address 0000–00FF in the program space will be occupied by boot ROM. †

‡

Figure 2. TMS320LF2406 Memory Map

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

memory maps (continued) – ’LF2402

Reserved

On-Chip Flash Memory (Sectored)

0000 005F

0060

Hex Data

Memory-Mapped

Registers/Reserved Addresses

007F 0080

On-Chip DARAM B2

01FF

0200

Reserved

02FF

0300

On-Chip DARAM (B0)‡ (CNF = 0)

Reserved (CNF = 1)

03FF

0400

On-Chip DARAM (B1)

07FF

0800

Reserved

6FFF

7000

Reserved

Peripheral Memory-Mapped Registers (System, WD, ADC,

SCI, I/O, Interrupts)

7FFF

8000

Reserved

0000

Hex I/O

FEFF

FF00

FF0E

FF0F

Reserved

FFFF

FFFE

FF10

Flash Control Mode Register

(Only for Flash devices)

FFFF

0FFF

1000

Reserved

0000

Hex Program

Interrupt Vectors

FFFF

FEFF

FF00

Reserved† (CNF = 1)

External (CNF = 0)

FDFF FE00

On-Chip DARAM (B0)† (CNF = 1)

External (CNF = 0)

0FFF

003F

Hex Program

7FFF

8000

FFFF

FEFF

FF00

Reserved† (CNF = 1)

External (CNF = 0)

FDFF FE00

Reserved

FLASH SECTOR 0 (4K)

FLASH SECTOR 1 (4K)

Reserved

87FF

8800

2000

Reserved

1000

1FFF

0040

NOTE A: Boot ROM: If the boot ROM is enabled, then address 0000–00FF in the program space will be occupied by boot ROM. †

‡

Figure 3. TMS320LF2402 Memory Map

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

memory maps (continued) – ’LC2406

Reserved

On-Chip ROM

32K

Reserved

Program

Interrupt Vectors

Hex Data

Memory-Mapped

Registers/Reserved Addresses

On-Chip DARAM B2

Reserved

On-Chip DARAM (B0)‡ (CNF = 0)

Reserved (CNF = 1)

On-Chip DARAM (B1)

Reserved

SARAM (2K) (DON = 1)

Internal

Reserved (DON = 0)

Reserved

Peripheral Memory-Mapped

Registers (System, WD, ADC,

SCI, SPI, CAN, I/O, Interrupts)

Hex I/O

Reserved

Reserved† (CNF = 1)

External (CNF = 0)

On-Chip DARAM (B0)† (CNF = 1)

Reserved (CNF = 0)

Reserved

SARAM (See Table 1 for details.)

On-Chip ROM memory

Reserved in the ’LC240x devices

Reserved

0000

003F 0040

Hex

7FFF 8000

FFFF

FEFF FF00

FDFF FE00

0000 005F

0060 007F

0080

01FF

0200

02FF

0300

03FF

0400

07FF

0800

6FFF

7000

7FFF

8000

FFFF

0FFF

1000

0000

FEFF

FF00 FF0E

FF0F

FFFF

FFFE

FF10

SARAM (2K) (PON = 1)

Internal

Reserved (PON = 0)

87FF

8800

†

‡

Figure 4. TMS320LC2406 Memory Map

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

memory maps (continued) – ’LC2404

Reserved

On-Chip ROM

16K

Reserved

Program

Interrupt Vectors

Hex Data

Memory-Mapped

Registers/Reserved Addresses

On-Chip DARAM B2

Reserved

On-Chip DARAM (B0)‡ (CNF = 0)

Reserved (CNF = 1)

On-Chip DARAM (B1)

Reserved

SARAM (1K) (DON = 1)

Internal

Reserved (DON = 0)

Reserved

Peripheral Memory-Mapped Registers (System, WD, ADC,

SCI, SPI, I/O, Interrupts)

Hex I/O

Reserved

Reserved† (CNF = 1)

External (CNF = 0)

On-Chip DARAM (B0)† (CNF = 1)

Reserved (CNF = 0)

Reserved

SARAM (See Table 1 for details.)

On-Chip ROM memory

Reserved in the ’LC240x devices

Reserved

0000

003F

0040

Hex

7FFF 8000

FFFF

FEFF

FF00

FDFF FE00

83FF 8400

0000

005F

0060

007F

0080

01FF

0200

02FF

0300

03FF

0400

07FF

0800

6FFF

7000

7FFF

8000

FFFF

0BFF 0C00

0000

FEFF

FF00

FF0E

FF0F

FFFF

FFFE

FF10

SARAM (1K) (PON = 1)

Internal

Reserved (PON = 0)

Reserved

3FFF

4000

†

‡

Figure 5. TMS320LC2404 Memory Map

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

memory maps (continued) – ’LC2402

Reserved

On-Chip ROM (4K)

Reserved

Program

Interrupt Vectors

Hex Data

Memory-Mapped

Registers/Reserved Addresses

On-Chip DARAM B2

Reserved

On-Chip DARAM (B0)‡ (CNF = 0)

Reserved (CNF = 1)

On-Chip DARAM (B1)

Reserved

Peripheral Memory-Mapped

Registers (System, WD, ADC,

SCI, I/O, Interrupts)

Hex I/O

Reserved

Reserved† (CNF = 1)

External (CNF = 0)

On-Chip DARAM (B0)† (CNF = 1)

Reserved (CNF = 0)

Reserved

On-Chip ROM memory

Reserved in the ’LC240x devices

Reserved

0000

003F

Hex

8000

FFFF

FEFF FF00

FDFF FE00

87FF

8800

0000 005F

0060 007F

0080

01FF

0200

02FF

0300

03FF

0400

07FF

0800

6FFF

7000

7FFF

8000

FFFF

0FFF

1000

0000

FEFF

FF00 FF0E

FF0F

FFFF

FFFE

FF10

7FFF

Reserved

0FFF

0040

†

‡

Figure 6. TMS320LC2402 Memory Map

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral memory map of the ’LF240x/’LC240x

Illegal

Reserved

70C0–70FF

General-Purpose

Timer Registers

Flag Registers

Event Manager – EVB

Deadband Registers

Compare, PWM, and

Interrupt Mask, Vector, and

Capture and QEP Registers

7500–7508

7511–7519 7520–7529

752C–7531

7532–753F

7432–743F

742C–7431

7420–7429

7411–7419

7400–7408

Reserved

Flag Registers

Interrupt Mask, Vector and

Capture and QEP Registers

Deadband Registers

Compare, PWM, and

Timer Registers

General-Purpose

Event Manager – EVA

7230–73FF

7100–722F

70A0–70BF

7090–709F

7080–708F

7070–707F

7060–706F

7050–705F

7040–704F

7030–703F

7020–702F

7010–701F

7000–700F

CAN Control Registers

ADC Control Registers

Digital I/O Control Registers

External-Interrupt Registers

SCI

SPI

Watchdog Timer Registers

Control Registers

System Configuration and

Hex

005F

0007

0006

0005

0004

0003

0000

and Reserved

Emulation Registers

Interrupt Flag Register

Global-Memory Allocation

Interrupt-Mask Register

FFFF

8000

7FFF

7540

753F

7500

74FF

7440

743F

7400

73FF

7000

6FFF

0800

07FF

0400

03FF

0300

02FF

0200

01FF

0080

007F

0060

005F

0000

External

Illegal

Peripheral Frame 3 (PF3)

Peripheral Frame 2 (PF2)

Peripheral Frame 1 (PF1)

Reserved

On-Chip DARAM B1

On-Chip DARAM B0

Reserved

On-Chip DARAM B2

and Reserved

Memory-Mapped Registers

“Illegal” indicates that access to these addresses causes a nonmaskable interrupt (NMI).

Reserved

Illegal

“Reserved” indicates addresses that are reserved for test and future expansion.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

device reset and interrupts

The TMS320x240x software-programmable interrupt structure supports flexible on-chip and external interrupt configurations to meet real-time interrupt-driven application requirements. The ’LF240x recognizes three types of interrupt sources.

D Reset (hardware- or software-initiated) is unarbitrated by the CPU and takes immediate priority over any

other executing functions. All maskable interrupts are disabled until the reset service routine enables them. The ’LF240x devices have two sources of reset: an external reset pin and a watchdog timer timeout (reset).

D Hardware-generated interrupts are requested by external pins or by on-chip peripherals. There are two

types: –

External interrupts

are generated by one of four external pins corresponding to the interrupts XINT1, XINT2, PDPINT A, and PDPINTB. These four can be masked both by dedicated enable bits and by t he CPU’s interrupt mask register (IMR), which can mask each maskable interrupt line at the DSP core.

–

Peripheral interrupts

are initiated internally by these on-chip peripheral modules: event manager A, event manager B, SPI, SCI, WD, CAN, and ADC. They can be masked both by enable bits for each event in each peripheral and by the CPU’s IMR, which can mask each maskable interrupt line at the DSP core.

D Software-generated interrupts for the ’LF240x devices include:

–

The INTR instruction.

This instruction allows initialization of any ’LF240x interrupt with software. Its operand indicates the interrupt vector location to which the CPU branches. This instruction globally disables maskable interrupts (sets the INTM bit to 1).

–

The NMI instruction.

This instruction forces a branch to interrupt vector location 24h. This instruction globally disables maskable interrupts. ’240x devices do not have the NMI hardware signal, only software activation is provided.

–

The TRAP instruction.

This instruction forces the CPU to branch to interrupt vector location 22h. The

TRAP instruction does

not

disable maskable interrupts (INTM is not set to 1); therefore, when the CPU branches to the interrupt service routine, that routine can be interrupted by the maskable hardware interrupts.

–

An emulator trap.

This interrupt can be generated with either an INTR instruction or a TRAP instruction.

Six core interrupts (INT1–INT6) are expanded using a peripheral interrupt expansion (PIE) module identical to the ’F24x devices. The PIE manages all the peripheral interrupts from the ’240x peripherals and are grouped to share the six-core level interrupts. Figure 7 shows the PIE block diagram for hardware-generated interrupts.

The PIE diagram (Figure 7) and the interrupt table (Table 3) explain the grouping and interrupt vector maps. ’LF240x devices have interrupts identical to the ’F24x devices and should be completely code-compatible. ’240x devices also have peripheral interrupts identical to the ’F24x – plus additional interrupts for new peripherals such as event manager B. Though the new interrupts share the ’24x interrupt grouping, they all have a unique vector to differentiate among the interrupts. See Table 3 for details.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

CPU

IACK

Addr

Bus

Data

Bus

PIVR & Logic

PIRQR# PIACK#

IRQ GEN

Level 6

IRQ GEN

Level 5

IRQ GEN

Level 4

IRQ GEN

Level 3

IRQ GEN

Level 2

IRQ GEN

Level 1

ADCINT

CANERINT

CANMBINT

TXINT

RXINT

SPIINT

CAP3INT

CAP2INT

CAP1INT

T2OFINT

T2UFINT

T2CINT

T2PINT

T1OFINT

T1UFINT

T1CINT

T1PINT

CMP3INT

CMP2INT

CMP1INT

CANERINT

CANMBINT

TXINT

RXINT

SPIINT

ADCINT

PDPINTB

INT1

INT2

INT3

INT4

INT6

INT5

IMR IFR

PIE

CAP6INT

CAP5INT

CAP4INT

T4OFINT

T4UFINT

T4CINT

T4PINT

CMP6INT

CMP5INT

CMP4INT

T3OFINT

T3UFINT

T3PINT T3CINT

PDPINTA

Indicates change with respect to the TMS320F243/F241/C242 data sheets.

XINT1

XINT2

XINT1

XINT2

Interrupts from external interrupt pins. The remaining interrupts are internal to the peripherals.

Figure 7. Peripheral Interrupt Expansion (PIE) Module Block Diagram for Hardware-Generated Interrupts

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

interrupt request structure

Table 3. ’LF240x/’LC240x Interrupt Source Priority and Vectors

INTERRUPT

NAME

OVERALL PRIORITY

CPU

INTERRUPT

AND

VECTOR

ADDRESS

BIT POSITION IN PIRQRx AND

PIACKRx

PERIPHERAL

INTERRUPT

VECTOR

(PIV)

MASKABLE?

SOURCE

PERIPHERAL

MODULE

DESCRIPTION

Reset 1

RSN

0000h

N/A N

RS pin,

Watchdog

Reset from pin, watchdog timeout

Reserved 2

–

0026h

N/A N CPU Emulator trap

NMI 3

NMI

0024h

N/A N

Nonmaskable

Interrupt

Nonmaskable interrupt, software interrupt only

PDPINTA 4 0.0 0020h Y EVA

Power device protection

PDPINTB 5 2.0 0019h Y EVB

Power device rotection

interrupt pins

ADCINT 6

0.1 0004h Y ADC

ADC interrupt in high-priority mode

XINT1 7 0.2 0001h Y

External

Interrupt Logic

External interrupt pins in high priority

XINT2 8

0.3 0011h Y

External

Interrupt Logic

External interrupt pins in high priority

SPIINT 9

INT1

0.4 0005h Y SPI SPI interrupt pins in high priority

RXINT 10

0002h

0.5 0006h Y SCI

SCI receiver interrupt in high-priority mode

TXINT 11 0.6 0007h Y SCI

SCI transmitter interrupt in high-priority mode

CANMBINT 12 0.7 0040 Y CAN

CAN mailbox in high-priority mode

CANERINT 13 0.8 0041 Y CAN

CAN error interrupt in

high-priority mode CMP1INT 14 0.9 0021h Y EVA Compare 1 interrupt CMP2INT 15 0.10 0022h Y EVA Compare 2 interrupt CMP3INT 16 0.11 0023h Y EVA Compare 3 interrupt T1PINT 17

0.12 0027h Y EVA Timer 1 period interrupt

T1CINT 18

INT2

0.13 0028h Y EVA Timer 1 compare interrupt

T1UFINT 19

0004h

0.14 0029h Y EVA Timer 1 underflow interrupt T1OFINT 20 0.15 002Ah Y EVA Timer 1 overflow interrupt CMP4INT 21 2.1 0024h Y EVB Compare 4 interrupt CMP5INT 22 2.2 0025h Y EVB Compare 4 interrupt CMP6INT 23 2.3 0026h Y EVB Compare 4 interrupt T3PINT 24 2.4 002Fh Y EVB Timer 3 period interrupt T3CINT 25 2.5 0030h Y EVB Timer 3 compare interrupt T3UFINT 26 2.6 0031h Y EVB Timer 3 underflow interrupt T3OFINT 27 2.7 0032h Y EVB Timer 3 overflow interrupt

†

Refer to the

TMS320C240 DSP Controllers CPU, System, and Instruction Set Reference Guide

(literature number SPRU160) and the

TMS320F243/’F241/’C242 DSP Controllers System and Peripherals User’s Guide

(literature number SPRU276) for more information.

New peripheral interrupts and vectors with respect to the ’F243/’F241 devices.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

interrupt request structure (continued)

Table 3.’LF240x/’LC240x Interrupt Source Priority and Vectors (Continued)

INTERRUPT

NAME

OVERALL PRIORITY

CPU

INTERRUPT

AND

VECTOR

ADDRESS

BIT POSITION IN PIRQRx AND

PIACKRx

PERIPHERAL

INTERRUPT

VECTOR

(PIV)

MASK-

ABLE?

SOURCE

PERIPHERAL

MODULE

DESCRIPTION

T2PINT 28 1.0 002Bh Y EVA Timer 2 period interrupt T2CINT 29 1.1 002Ch Y EVA Timer 2 compare interrupt T2UFINT 30 1.2 002Dh Y EVA Timer 2 underflow interrupt T2OFINT 31

INT3

1.3 002Eh Y EVA Timer 2 overflow interrupt

T4PINT 32

INT3

0006h

2.8 0039h Y EVB Timer 4 period interrupt T4CINT 33 2.9 003Ah Y EVB Timer 4 compare interrupt T4UFINT 34 2.10 003Bh Y EVB Timer 4 underflow interrupt T4OFINT 35 2.11 003Ch Y EVB Timer 4 overflow interrupt CAP1INT 36 1.4 0033h Y EVA Capture 1 interrupt CAP2INT 37 1.5 0034h Y EVA Capture 2 interrupt CAP3INT 38

INT4

1.6 0035h Y EVA Capture 3 interrupt CAP4INT 39

INT4

0008h

2.12 0036h Y EVB Capture 4 interrupt CAP5INT 40 2.13 0037h Y EVB Capture 5 interrupt CAP6INT 41 2.14 0038h Y EVB Capture 6 interrupt SPIINT 42 1.7 0005h Y SPI SPI interrupt (low priority)

RXINT 43 1.8 0006h Y SCI

SCI receiver interrupt (low-priority mode)

TXINT 44

INT5

1.9 0007h Y SCI

SCI transmitter interrupt (low-priority mode)

CANMBINT 45

000Ah

1.10 0040h Y CAN

CAN mailbox interrupt (low-priority mode)

CANERINT 46 1.11 0041h Y CAN

CAN error interrupt (low-priority mode)

ADCINT 47 1.12 0004h Y ADC

ADC interrupt (low priority)

XINT1 48

INT6

000Ch

1.13 0001h Y

External

Interrupt Logic

External interrupt pins (low-priority mode)

XINT2 49

000Ch

1.14 001 1h Y

External

Interrupt Logic

External interrupt pins

(low-priority mode) Reserved 000Eh N/A Y CPU Analysis interrupt TRAP N/A 0022h N/A N/A CPU TRAP instruction Phantom

Interrupt Vector

N/A N/A 0000h N/A CPU Phantom interrupt vector

INT8–INT16 N/A 0010h–0020h N/A N/A CPU INT20–INT31 N/A 00028h–0603Fh N/A N/A CPU

Software interrupt vectors

†

Refer to the

TMS320C240 DSP Controllers CPU, System, and Instruction Set Reference Guide

(literature number SPRU160) and the

TMS320F243/’F241/’C242 DSP Controllers System and Peripherals User’s Guide

(literature number SPRU276) for more information.

New peripheral interrupts and vectors with respect to the ’F243/’F241 devices.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

DSP CPU Core

The TMS320x240x devices use an advanced Harvard-type architecture that maximizes processing power by maintaining two separate memory bus structures — program and data — for full-speed execution. This multiple bus structure allows data and instructions to be read simultaneously. Instructions support data transfers between program memory and data memory . This architecture permits coefficients that are stored in program memory to be read in RAM, thereby eliminating the need for a separate coefficient ROM. This, coupled with a four-deep pipeline, allows the ’LF240x/’LC240x devices to execute most instructions in a single cycle. See the architectural block diagram of the ’24x DSP Core for more information.

TMS320x240x instruction set

The ’x240x microprocessor implements a comprehensive instruction set that supports both numeric-intensive signal-processing operations and general-purpose applications, such as multiprocessing and high-speed control. Source code for the ’C1x and ’C2x DSPs is upwardly compatible with the ’x243/’x241 and ’240x devices.

For maximum throughput, the next instruction is prefetched while the current one is being executed. Because the same data lines are used to communicate to external data, program, or I/O space, the number of cycles an instruction requires to execute varies, depending upon whether the next data operand fetch is from internal or external memory. Highest throughput is achieved by maintaining data memory on chip and using either internal or fast external program memory.

addressing modes

The TMS320x240x instruction set provides four basic memory-addressing modes: direct, indirect, immediate, and register.

In direct addressing, the instruction word contains the lower seven bits of the data memory address. This field is concatenated with the nine bits of the data memory page pointer (DP) to form the 16-bit data memory address. Therefore, in the direct-addressing mode, data memory is paged effectively with a total of 512 pages, with each page containing 128 words.

Indirect addressing accesses data memory through the auxiliary registers. In this addressing mode, the address of the instruction operand is contained in the currently selected auxiliary register. Eight auxiliary registers (AR0–AR7) provide flexible and powerful indirect addressing. T o select a specific auxiliary register , the auxiliary register pointer (ARP) is loaded with a value from 0 to 7 for AR0 through AR7, respectively.

scan-based emulation

TMS320x2xx devices incorporate scan-based emulation logic for code-development and hardwaredevelopment support. Scan-based emulation allows the emulator to control the processor in the system without the use of intrusive cables to the full pinout of the device. The scan-based emulator communicates with the ’x2xx by way of the IEEE 1149.1-compatible (JTAG) interface. The ’x240x DSPs, like the TMS320F243/241, TMS320F206, TMS320C203, and TMS320LC203, do not include boundary scan. The scan chain of these devices is useful for emulation function only.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

functional block diagram of the ’240x DSP CPU

Data Bus

OSCALE (0–7)

D15–D0

A15–A0

1616

ACCL(16)ACCH(16)C

CALU(32)

3232

MUX

ISCALE (0–16)

MUX

PREG(32)

Multiplier

TREG0(16)

MUX

B1 (256 × 16)

B2 (32 × 16)

DARAM

B0 (256 × 16)

DARAM

7 LSB from IR

MUX

DP(9)

MUX

1616

ARAU(16)

ARB(3)

ARP(3)

Program Bus

AR7(16)

AR6(16)

AR5(16)

AR3(16)

AR2(16)

AR1(16)

AR0(16)

Stack 8 × 16

MUX

XTAL2

CLKOUT

XTAL1

XINT[1–2]

MP/MC

READY

STRB

R/W

Control

Data Bus

Program Bus

Data Bus

AR4(16)

MUXMUX

Data/Prog

PSCALE (–6,ā0,ā1,ā4)

Data

FLASH EEPROM/

ROM

MUX

NPAR

PAR MSTACK

Program Control

(PCTRL)

Memory Map

IFR (16)

GREG (16)

Program Bus

NOTES: A. See T able 4 for symbol descriptions.

B. For clarity, the data and program buses are shown as single buses although they include address and data bits.

C. Refer to the TMS320F243, TMS320F241 DSP Controllers data sheet (literature number SPRS064), the TMS320C240,

TMS320F240 DSP Controllers data sheet (literature number SPRS042), and the

TMS320C240 DSP Controllers CPU, System, and

Instruction Set Reference Guide

(literature number SPRU160) for CPU instruction set information.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

’240x legend for the internal hardware

Table 4. Legend for the ’240x DSP CPU Internal Hardware

SYMBOL NAME DESCRIPTION

ACC Accumulator

32-bit register that stores the results and provides input for subsequent CALU operations. Also includes shift and rotate capabilities

ARAU

Auxiliary Register Arithmetic Unit

An unsigned, 16-bit arithmetic unit used to calculate indirect addresses using the auxiliary registers as inputs and outputs

AUX REGS

Auxiliary Registers 0–7

These 16-bit registers are used as pointers to anywhere within the data space address range. They are operated upon by the ARAU and are selected by the auxiliary register pointer (ARP). AR0 can also be used as an index value for AR updates of more than one and as a compare value to AR.

C Carry

Register carry output from CALU. C is fed back into the CALU for extended arithmetic operation. The C bit resides in status register 1 (ST1), and can be tested in conditional instructions. C is also used in accumulator shifts and rotates.

CALU

Central Arithmetic Logic Unit

32-bit-wide main arithmetic logic unit for the TMS320C2xx core. The CALU executes 32-bit operations in a single machine cycle. CALU operates on data coming from ISCALE or PSCALE with data from ACC, and provides status results to PCTRL.

DARAM Dual-Access RAM

If the on-chip RAM configuration control bit (CNF) is set to 0, the reconfigurable data dual-access RAM (DARAM) block B0 is mapped to data space; otherwise, B0 is mapped to program space. Blocks B1 and B2 are mapped to data memory space only, at addresses 0300–03FF and 0060–007F, respectively. Blocks 0 and 1 contain 256 words, while block 2 contains 32 words.

Data Memory Page Pointer

The 9-bit DP register is concatenated with the seven least significant bits (LSBs) of an instruction word to form a direct memory address of 16 bits. DP can be modified by the LST and LDP instructions.

GREG

Global Memory Allocation Register

GREG specifies the size of the global data memory space. Since the global memory space is not used in the ’240x devices, this register is reserved.

IMR

Interrupt Mask Register

IMR individually masks or enables the seven interrupts.

IFR

Interrupt Flag Register

The 7-bit IFR indicates that the TMS320C2xx has latched an interrupt from one of the seven maskable interrupts.

INT# Interrupt Traps A total of 32 interrupts by way of hardware and/or software are available. ISCALE

Input Data-Scaling Shifter

16- to 32-bit barrel left-shifter. ISCALE shifts incoming 16-bit data 0 to16 positions left, relative to the 32-bit output within the fetch cycle; therefore, no cycle overhead is required for input scaling operations.

MPY Multiplier

16 × 16-bit multiplier to a 32-bit product. MPY executes multiplication in a single cycle. MPY operates either signed or unsigned 2s-complement arithmetic multiply.

MSTACK Micro Stack

MSTACK provides temporary storage for the address of the next instruction to be fetched when program address-generation logic is used to generate sequential addresses in data space.

MUX Multiplexer Multiplexes buses to a common input NPAR

Next Program Address Register

NPAR holds the program address to be driven out on the PAB in the next cycle.

OSCALE

Output Data-Scaling Shifter

16- to 32-bit barrel left-shifter. OSCALE shifts the 32-bit accumulator output 0 to 7 bits left for quantization management and outputs either the 16-bit high- or low-half of the shifted 32-bit data to the data-write data bus (DWEB).

PAR

Program Address Register

PAR holds the address currently being driven on P AB for as many cycles as it takes to complete all memory operations scheduled for the current bus cycle.

PC Program Counter

PC increments the value from NPAR to provide sequential addresses for instruction-fetching and sequential data-transfer operations.

PCTRL

Program Controller

PCTRL decodes instruction, manages the pipeline, stores status, and decodes conditional operations.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

’240x legend for the internal hardware (continued)

Table 4. Legend for the ’240x DSP CPU Internal Hardware (Continued)

SYMBOL NAME DESCRIPTION

PREG Product Register 32-bit register holds results of 16 × 16 multiply

PSCALE

Product-Scaling Shifter

0-, 1-, or 4-bit left shift, or 6-bit right shift of multiplier product. The left-shift options are used to manage the additional sign bits resulting from the 2s-complement multiply. The right-shift option is used to scale down the number to manage overflow of product accumulation in the CALU. PSCALE resides in the path from the 32-bit product shifter and from either the CALU or the data-write data bus (DWEB), and requires no cycle overhead.

STACK Stack

STACK is a block of memory used for storing return addresses for subroutines and interrupt-service routines, or for storing data. The ’C2xx stack is 16-bit wide and eight-level deep.

TREG

Temporary Register

16-bit register holds one of the operands for the multiply operations. TREG holds the dynamic shift count for the LACT, ADDT, and SUBT instructions. TREG holds the dynamic bit position for the BITT instruction.

status and control registers

Two status registers, ST0 and ST1, contain the status of various conditions and modes. These registers can be stored into data memory and loaded from data memory , thus allowing the status of the machine to be saved and restored for subroutines.

The load status register (LST) instruction is used to write to ST0 and ST1. The store status register (SST) instruction is used to read from ST0 and ST1 — except for the INTM bit, which is not affected by the LST instruction. The individual bits of these registers can be set or cleared when using the SETC and CLRC instructions. Figure 8 shows the organization of status registers ST0 and ST1, indicating all status bits contained in each. Several bits in the status registers are reserved and are read as logic 1s. Table 5 lists status register field definitions.

15 13 12 11 10 9 8 0

ST0

ARP OV OVM 1 INTM DP

15 13 12 11 10 9 8 7 6 5 4 3 2 1 0

ST1

ARB CNF TC SXM C 1 1 1 1 XF 1 1 PM

Figure 8. Organization of Status Registers ST0 and ST1

Table 5. Status Register Field Definitions

FIELD FUNCTION

ARB

Auxiliary register pointer buffer . When the ARP is loaded into ST0, the old ARP value is copied to the ARB except during an LST instruction. When the ARB is loaded by way of an LST #1 instruction, the same value is also copied to the ARP.

ARP

Auxiliary register (AR) pointer. ARP selects the AR to be used in indirect addressing. When the ARP is loaded, the old ARP value is copied to the ARB register. ARP can be modified by memory-reference instructions when using indirect addressing, and by the LARP, MAR, and LST instructions. The ARP is also loaded with the same value as ARB when an LST #1 instruction is executed.

Carry bit. C is set to 1 if the result of an addition generates a carry, or reset to 0 if the result of a subtraction generates a borrow. Otherwise, C is reset after an addition or set after a subtraction, except if the instruction is ADD or SUB with a 16-bit shift. In these cases, ADD can only set and SUB can only reset the carry bit, but cannot affect it otherwise. The single-bit shift and rotate instructions also affect C, as well as the SETC, CLRC, and LST #1 instructions. Branch instructions have been provided to branch on the status of C. C is set to 1 on a reset.

CNF

On-chip RAM configuration control bit. If CNF is set to 0, the reconfigurable data dual-access RAM blocks are mapped to data space; otherwise, they are mapped to program space. The CNF can be modified by the SETC CNF, CLRC CNF, and LST #1 instructions. RS

sets the CNF to 0.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

status and control registers (continued)

Table 5. Status Register Field Definitions (Continued)

FIELD FUNCTION

Data memory page pointer. The 9-bit DP register is concatenated with the seven LSBs of an instruction word to form a direct memory address of 16 bits. DP can be modified by the LST and LDP instructions.

INTM

Interrupt mode bit. When INTM is set to 0, all unmasked interrupts are enabled. When set to 1, all maskable interrupts are disabled. INTM is set and reset by the SETC INTM and CLRC INTM instructions. RS

also sets INTM. INTM has no effect on the unmaskable

and NMI interrupts. Note that INTM is unaffected by the LST instruction. This bit is set to 1 by reset. It is also set to 1 when

a maskable interrupt trap is taken.

Overflow flag bit. As a latched overflow signal, OV is set to 1 when overflow occurs in the arithmetic logic unit (ALU). Once an overflow occurs, the OV remains set until a reset, BCND/D on OV/NOV, or LST instruction clears OV .

OVM

Overflow mode bit. When OVM is set to 0, overflowed results overflow normally in the accumulator. When set to 1, the accumulator is set to either its most positive or negative value upon encountering an overflow. The SETC and CLRC instructions set and reset this bit, respectively. LST can also be used to modify the OVM.

Product shift mode. If these two bits are 00, the multiplier’s 32-bit product is loaded into the ALU with no shift. If PM = 01, the PREG output is left-shifted one place and loaded into the ALU, with the LSB zero-filled. If PM = 10, the PREG output is left-shifted by four bits and loaded into the ALU, with the LSBs zero-filled. PM = 11 produces a right shift of six bits, sign-extended. Note that the PREG contents remain unchanged. The shift takes place when transferring the contents of the PREG to the ALU. PM is loaded by the SPM and LST #1 instructions. PM is cleared by RS

SXM

Sign-extension mode bit. SXM = 1 produces sign extension on data as it is passed into the accumulator through the scaling shifter. SXM = 0 suppresses sign extension. SXM does not affect the definitions of certain instructions; for example, the ADDS instruction suppresses sign extension regardless of SXM. SXM is set by the SETC SXM instruction and reset by the CLRC SXM instruction and can be loaded by the LST #1 instruction. SXM is set to 1 by reset.

T est/control flag bit. TC is af fected by the BIT, BITT , CMPR, LST #1, and NORM instructions. TC is set to a 1 if a bit tested by BIT or BITT is a 1, if a compare condition tested by CMPR exists between AR (ARP) and AR0, if the exclusive-OR function of the two most significant bits (MSBs) of the accumulator is true when tested by a NORM instruction. The conditional branch, call, and return instructions can execute based on the condition of TC.

XF pin status bit. XF indicates the state of the XF pin, a general-purpose output pin. XF is set by the SETC XF instruction and reset by the CLRC XF instruction. XF is set to 1 by reset.

central processing unit

The TMS320x240x central processing unit (CPU) contains a 16-bit scaling shifter, a 16 x 16-bit parallel multiplier, a 32-bit central arithmetic logic unit (CALU), a 32-bit accumulator, and additional shifters at the outputs of both the accumulator and the multiplier. This section describes the CPU components and their functions. The functional block diagram shows the components of the CPU.

input scaling shifter

The TMS320x240x provides a scaling shifter with a 16-bit input connected to the data bus and a 32-bit output connected to the CALU. This shifter operates as part of the path of data coming from program or data space to the CALU and requires no cycle overhead. It is used to align the 16-bit data coming from memory to the 32-bit CALU. This is necessary for scaling arithmetic as well as aligning masks for logical operations.

The scaling shifter produces a left shift of 0 to 16 on the input data. The LSBs of the output are filled with zeros; the MSBs can either be filled with zeros or sign-extended, depending upon the value of the SXM bit (sign-extension mode) of status register ST1. The shift count is specified by a constant embedded in the instruction word or by a value in TREG. The shift count in the instruction allows for specific scaling or alignment operations specific to that point in the code. The TREG base shift allows the scaling factor to be adaptable to the system’s performance.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

multiplier

The TMS320x240x devices use a 16 x 16-bit hardware multiplier that is capable of computing a signed or an unsigned 32-bit product in a single machine cycle. All multiply instructions, except the MPYU (multiply unsigned) instruction, perform a signed multiply operation. That is, two numbers being multiplied are treated as 2s-complement numbers, and the result is a 32-bit 2s-complement number. There are two registers associated with the multiplier, as follow:

D 16-bit temporary register (TREG) that holds one of the operands for the multiplier D 32-bit product register (PREG) that holds the product

Four product-shift modes (PM) are available at the PREG output (PSCALE). These shift modes are useful for performing multiply/accumulate operations, performing fractional arithmetic, or justifying fractional products. The PM field of status register ST1 specifies the PM shift mode, as shown in Table 6.

Table 6. PSCALE Product-Shift Modes

PM SHIFT DESCRIPTION

00 No shift Product feed to CALU or data bus with no shift 01 Left 1 Removes the extra sign bit generated in a 2s-complement multiply to produce a Q31 product

10 Left 4

Removes the extra 4 sign bits generated in a 16x13 2s-complement multiply to a produce a Q31 product when using the multiply-by-a-13-bit constant

11 Right 6 Scales the product to allow up to 128 product accumulation without the possibility of accumulator overflow

The product can be shifted one bit to compensate for the extra sign bit gained in multiplying two 16-bit 2s-complement numbers (MPY instruction). A four-bit shift is used in conjunction with the MPY instruction with a short immediate value (13 bits or less) to eliminate the four extra sign bits gained in multiplying a 16-bit number by a 13-bit number. Finally, the output of PREG can be right-shifted 6 bits to enable the execution of up to 128 consecutive multiply/accumulates without the possibility of overflow.

The L T (load TREG) instruction normally loads TREG to provide one operand (from the data bus), and the MPY (multiply) instruction provides the second operand (also from the data bus). A multiplication also can be performed with a 13-bit immediate operand when using the MPY instruction. Then, a product is obtained every two cycles. When the code is executing multiple multiplies and product sums, the CPU supports the pipelining of the TREG load operations with CALU operations using the previous product. The pipeline operations that run in parallel with loading the TREG include: load ACC with PREG (L TP); add PREG to ACC (L TA); add PREG to ACC and shift TREG input data (DMOV) to next address in data memory (L TD); and subtract PREG from ACC (L TS).

Two multiply/accumulate instructions (MAC and MACD) fully utilize the computational bandwidth of the multiplier, allowing both operands to be processed simultaneously. The data for these operations can be transferred to the multiplier each cycle by way of the program and data buses. This facilitates single-cycle multiply/accumulates when used with the repeat (RPT) instruction. In these instructions, the coefficient addresses are generated by program address generation (PAGEN) logic, while the data addresses are generated by data address generation (DAGEN) logic. This allows the repeated instruction to access the values from the coefficient table sequentially and step through the data in any of the indirect addressing modes.

The MACD instruction, when repeated, supports filter constructs (weighted running averages) so that as the sum-of-products is executed, the sample data is shifted in memory to make room for the next sample and to throw away the oldest sample.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

multiplier (continued)

The MPYU instruction performs an unsigned multiplication, which greatly facilitates extended-precision arithmetic operations. The unsigned contents of TREG are multiplied by the unsigned contents of the addressed data memory location, with the result placed in PREG. This process allows the operands of greater than 16 bits to be broken down into 16-bit words and processed separately to generate products of greater than 32 bits. The SQRA (square /add) and SQRS (square/subtract) instructions pass the same value to both inputs of the multiplier for squaring a data memory value.

After the multiplication of two 16-bit numbers, the 32-bit product is loaded into the 32-bit product register (PREG). The product from PREG can be transferred to the CALU or to data memory by way of the SPH (store product high) and SPL (store product low) instructions. Note: the transfer of PREG to either the CALU or data bus passes through the PSCALE shifter, and therefore is af fected by the product shift mode defined by PM. This is important when saving PREG in an interrupt-service-routine context save as the PSCALE shift effects cannot be modeled in the restore operation. PREG can be cleared by executing the MPY #0 instruction. The product register can be restored by loading the saved low half into TREG and executing a MPY #1 instruction. The high half, then, is loaded using the LPH instruction.

central arithmetic logic unit

The TMS320x240x central arithmetic logic unit (CALU) implements a wide range of arithmetic and logical functions, the majority of which execute in a single clock cycle. This ALU is referred to as central to differentiate it from a second ALU used for indirect-address generation called the auxiliary register arithmetic unit (ARAU). Once an operation is performed in the CALU, the result is transferred to the accumulator (ACC) where additional operations, such as shifting, can occur. Data that is input to the CALU can be scaled by ISCALE when coming from one of the data buses (DRDB or PRDB) or scaled by PSCALE when coming from the multiplier.

The CALU is a general-purpose ALU that operates on 16-bit words taken from data memory or derived from immediate instructions. In addition to the usual arithmetic instructions, the CALU can perform Boolean operations, facilitating the bit-manipulation ability required for a high-speed controller. One input to the CALU is always provided from the accumulator, and the other input can be provided from the product register (PREG) of the multiplier or the output of the scaling shifter (that has been read from data memory or from the ACC). After the CALU has performed the arithmetic or logical operation, the result is stored in the accumulator.

The TMS320x240x devices support floating-point operations for applications requiring a large dynamic range. The NORM (normalization) instruction is used to normalize fixed-point numbers contained in the accumulator by performing left shifts. The four bits of the TREG define a variable shift through the scaling shifter for the LACT/ADDT/SUBT (load/add to /subtract from accumulator with shift specified by TREG) instructions. These instructions are useful in floating-point arithmetic where a number needs to be denormalized — that is, floating-point to fixed-point conversion. They are also useful in the execution of an automatic gain control (AGC) going into a filter. The BITT (bit test) instruction provides testing of a single bit of a word in data memory based on the value contained in the four LSBs of TREG.

The CALU overflow saturation mode can be enabled/disabled by setting/resetting the OVM bit of ST0. When the CALU is in the overflow saturation mode and an overflow occurs, the overflow flag is set and the accumulator is loaded with either the most positive or the most negative value representable in the accumulator, depending on the direction of the overflow. The value of the accumulator at saturation is 07FFFFFFFh (positive) or 080000000h (negative). If the OVM (overflow mode) status register bit is reset and an overflow occurs, the overflowed results are loaded into the accumulator with modification. (Note that logical operations cannot result in overflow.)

The CALU can execute a variety of branch instructions that depend on the status of the CALU and the accumulator. These instructions can be executed conditionally based on any meaningful combination of these status bits. For overflow management, these conditions include OV (branch on overflow) and EQ (branch on accumulator equal to zero). In addition, the BACC (branch to address in accumulator) instruction provides the ability to branch to an address specified by the accumulator (computed goto). Bit test instructions (BIT and BITT), which do not affect the accumulator, allow the testing of a specified bit of a word in data memory.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

central arithmetic logic unit (continued)

The CALU also has an associated carry bit that is set or reset depending on various operations within the device. The carry bit allows more efficient computation of extended-precision products and additions or subtractions. It is also useful in overflow management. The carry bit is affected by most arithmetic instructions as well as the single-bit shift and rotate instructions. It is not affected by loading the accumulator , logical operations, or other such non-arithmetic or control instructions.

The ADDC (add to accumulator with carry) and SUBB (subtract from accumulator with borrow) instructions use the previous value of carry in their addition/subtraction operation.

The one exception to the operation of the carry bit is in the use of ADD with a shift count of 16 (add to high accumulator) and SUB with a shift count of 16 (subtract from high accumulator) instructions. This case of the ADD instruction can set the carry bit only if a carry is generated, and this case of the SUB instruction can reset the carry bit only if a borrow is generated; otherwise, neither instruction affects it.

Two conditional operands, C and NC, are provided for branching, calling, returning, and conditionally executing, based upon the status of the carry bit. The SETC, CLRC, and LST #1 instructions also can be used to load the carry bit. The carry bit is set to one on a hardware reset.

accumulator

The 32-bit accumulator is the registered output of the CALU. It can be split into two 16-bit segments for storage in data memory. Shifters at the output of the accumulator provide a left shift of 0 to 7 places. This shift is performed while the data is being transferred to the data bus for storage. The contents of the accumulator remain unchanged. When the postscaling shifter is used on the high word of the accumulator (bits 16–31), the MSBs are lost and the LSBs are filled with bits shifted in from the low word (bits 0–15). When the postscaling shifter is used on the low word, the LSBs are zero-filled.

The SFL and SFR (in-place one-bit shift to the left / right) instructions and the ROL and ROR (rotate to the left/right) instructions implement shifting or rotating of the contents of the accumulator through the carry bit. The SXM bit affects the definition of the SFR (shift accumulator right) instruction. When SXM = 1, SFR performs an arithmetic right shift, maintaining the sign of the accumulator data. When SXM = 0, SFR performs a logical shift, shifting out the LSBs and shifting in a zero for the MSB. The SFL (shift accumulator left) instruction is not affected by the SXM bit and behaves the same in both cases, shifting out the MSB and shifting in a zero. Repeat (RPT) instructions can be used with the shift and rotate instructions for multiple-bit shifts.

auxiliary registers and auxiliary-register arithmetic unit (ARAU)

The ’240x provides a register file containing eight auxiliary registers (AR0 –AR7). The auxiliary registers are used for indirect addressing of the data memory or for temporary data storage. Indirect auxiliary-register addressing allows placement of the data memory address of an instruction operand into one of the auxiliary registers. These registers are referenced with a 3-bit auxiliary register pointer (ARP) that is loaded with a value from 0 through 7, designating AR0 through AR7, respectively . The auxiliary registers and the ARP can be loaded from data memory , the ACC, the product register, or by an immediate operand defined in the instruction. The contents of these registers also can be stored in data memory or used as inputs to the CALU.

The auxiliary register file (AR0–AR7) is connected to the ARAU. The ARAU can autoindex the current auxiliary register while the data memory location is being addressed. Indexing either by ±1 or by the contents of the AR0 register can be performed. As a result, accessing tables of information does not require the CALU for address manipulation; therefore, the CALU is free for other operations in parallel.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

internal memory

The TMS320x240x devices are configured with the following memory modules:

D Dual-access random-access memory (DARAM) D Single-access random-access memory (SARAM) D Flash D ROM D Boot ROM

dual-access RAM (DARAM)

There are 544 words × 16 bits of DARAM on the ’240x devices. The ’240x DARAM allows writes to and reads from the RAM in the same cycle. The DARAM is configured in three blocks: block 0 (B0), block 1 (B1), and block 2 (B2). Block 1 contains 256 words and Block 2 contains 32 words, and both blocks are located only in data memory space. Block 0 contains 256 words, and can be configured to reside in either data or program memory space. The SETC CNF (configure B0 as data memory) and CLRC CNF (configure B0 as program memory) instructions allow dynamic configuration of the memory maps through software.

When using on-chip RAM or high-speed external memory , the ’240x runs at full speed with no wait states. The ability of the DARAM to allow two accesses to be performed in one cycle, coupled with the parallel nature of the ’240x architecture, enables the device to perform three concurrent memory accesses in any given machine cycle. Externally, the READY line or on-chip software wait-state generator can be used to interface the ’240x to slower, less expensive external memory . Downloading programs from slow of f-chip memory to on-chip RAM can speed processing while cutting system costs.

single-access RAM (SARAM)

There are 2K words × 16 bits of SARAM on some of the ’240x devices.

†

The ’240x SARAM allows writes to and reads from the RAM in the same cycle. The PON and DON bits select SARAM (2K) mapping in program space, data space, or both. See T able 18 for details on the SCSR2 register and the PON and DON bits. At reset, these bits are 1 1, and the on-chip SARAM is mapped in both the program and data spaces. The SARAM addresses (8000h in program memory and 0800h in data memory) are accessible in external memory space, if the on-chip SARAM is not enabled.

flash EEPROM

Flash EEPROM provides an attractive alternative to masked program ROM. Like ROM, flash is nonvolatile. However, it has the advantage of “in-target” reprogrammability. The ’LF240x incorporates one 32K  16-bit flash EEPROM module in program space. This type of memory expands the capabilities of the ’LF240x in the areas of prototyping, early field-testing, and single-chip applications. The flash module has multiple sectors that can be individually protected while erasing or programming. The sector size is non-uniform and partitioned as 4K/12K/12K/4K sectors.

Unlike most discrete flash memory , the ’LF240x flash does not require a dedicated state machine, because the algorithms for programming and erasing the flash are executed by the DSP core. This enables several advantages, including: reduced chip size and sophisticated, adaptive algorithms. For production programming, the IEEE Standard 1149.1

‡

(JTAG) scan port provides easy access to the on-chip RAM for downloading the

algorithms and flash code. This flash requires 5 V for programming (at V

CCP

pin only) the array . The flash runs

at zero wait state while the device is powered at 3.3 V.

ADVANCE

INFORMATION

†

See Table 1 for device-specific features.

‡

IEEE Standard 1149.1–1990, IEEE Standard Test Access Port.

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

ROM

The ’LC240x devices contain mask-programmable ROM located in program memory space. Customers can arrange to have this ROM programmed with contents unique to any particular application. See Table 1 for the ROM memory capacity of each ’LC240x device.

boot ROM

Boot ROM is a 256-word ROM memory mapped in program space 0000–00FF . This ROM will be enabled if the BOOTEN

pin is low during reset. The BOOT_EN bit (bit 3 of the SCSR2 register) will be set to 1 if the BOOTEN pin is low at reset. Boot ROM can also be enabled by writing 1 to the SCSR2.3 bit and disabled by writing 0 to this bit.

The boot ROM has a generic bootloader to transfer code through SCI or SPI ports. The incoming code should disable the BOOT_ROM bit by writing 0 to bit 3 of the SCSR2 register, or else, the whole flash array will not be enabled.

ADV ANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PERIPHERALS

The integrated peripherals of the TMS320x240x are described in the following subsections:

D Two event-manager modules (EVA, EVB) D Enhanced analog-to-digital converter (ADC) module D Controller area network (CAN) module D Serial communications interface (SCI) module D Serial peripheral interface (SPI) module D PLL-based clock module D Digital I/O and shared pin functions D External memory interfaces (’LF2407 only) D Watchdog (WD) timer module

event manager modules (EVA, EVB)

The event-manager modules include general-purpose (GP) timers, full-compare/PWM units, capture units, and quadrature-encoder pulse (QEP) circuits. EVA’s and EVB’s timers, compare units, and capture units function identically. However, timer/unit names differ for EVA and EVB. Table 7 shows the module and signal names used. T able 7 shows the features and functionality available for the event-manager modules and highlights EV A nomenclature.

Event managers A and B have identical peripheral register sets with EVA starting at 7400h and EVB starting at 7500h. The paragraphs in this section describe the function of GP timers, compare units, capture units, and QEPs using EVA nomenclature. These paragraphs are applicable to EVB with regard to function—however, module/signal names would differ.

Table 7. Module and Signal Names for EVA and EVB

EVENT MANAGER MODULES EVA MODULE SIGNAL EVB MODULE SIGNAL

GP Timers

Timer 1 Timer 2

T1PWM/T1CMP T2PWM/T2CMP

Timer 3 Timer 4

T3PWM/T3CMP T4PWM/T4CMP

Compare Units

Compare 1 Compare 2 Compare 3

PWM1/2 PWM3/4 PWM5/6

Compare 4 Compare 5 Compare 6

PWM7/8

PWM9/10

PWM11/12

Capture Units

Capture 1 Capture 2 Capture 3

CAP1 CAP2 CAP3

Capture 4 Capture 5 Capture 6

CAP4 CAP5 CAP6

QEP

QEP1 QEP2

QEP3 QEP4

External Inputs

Direction

External Clock

TDIRA

TCLKINA

Direction

External Clock

TDIRB

TCLKINB

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

event-manager modules (EVA, EVB) (continued)

Data Bus ADDR Bus Reset

INT2,3,4

Output

Logic

PWM1

PWM6

T2CMP/ T2PWM

T1CMP/ T1PWM

33 3

ADC Start of Conversion

QEP

Circuit

ClockDIR

CAP1/QEP1 CAP2/QEP2

CAP3

Prescaler

TDIR

†

TCLKIN

CLKOUT

(Internal)

T1CON[8,9,10]T1CON[4,5]

T2CON[8,9,10]

T2CON[4,5]

TCLKIN

TDIR

Output

Logic

Deadband

Units

SVPWM

State

Machine

CAPCON[14,13]

Capture Units

MUX

GP Timer 1

Full-Compare

Units

GP Timer 2

Compare

GP Timer 2

EV Control Registers

and Control Logic

GP Timer 1

Compare

Output

Logic

Clock

’240x DSP Core

Prescaler

CLKOUT

(Internal)

†

’2402 devices do not support external direction control. TDIR is not available.

Figure 9. Event-Manager Block Diagram

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

general-purpose (GP) timers

There are two GP timers: The GP timer x (x = 1 or 2 for EVA; x = 3 or 4 for EVB) includes:

D A 16-bit timer, up-/down-counter, TxCNT, for reads or writes D A 16-bit timer-compare register, TxCMPR (double-buffered with shadow register), for reads or writes D A 16-bit timer-period register, TxPR (double-buffered with shadow register), for reads or writes D A 16-bit timer-control register,TxCON, for reads or writes D Selectable internal or external input clocks D A programmable prescaler for internal or external clock inputs D Control and interrupt logic, for four maskable interrupts:

underflow, overflow, timer compare

, and

period

interrupts

D A selectable direction input pin (TDIR) (to count up or down when directional up- / down-count mode is

selected)

The GP timers can be operated independently or synchronized with each other. The compare register associated with each GP timer can be used for compare function and PWM-waveform generation. There are three continuous modes of operations for each GP timer in up- or up /down-counting operations. Internal or external input clocks with programmable prescaler are used for each GP timer. GP timers also provide the time base for the other event-manager submodules: GP timer 1 for all the compares and PWM circuits, GP timer 2/1 for the capture units and the quadrature-pulse counting operations. Double-buffering of the period and compare registers allows programmable change of the timer (PWM) period and the compare/PWM pulse width as needed.

full-compare units

There are three full-compare units on each event manager. These compare units use GP timer1 as the time base and generate six outputs for compare and PWM-waveform generation using programmable deadband circuit. The state of each of the six outputs is configured independently . The compare registers of the compare units are double-buffered, allowing programmable change of the compare/PWM pulse widths as needed.

programmable deadband generator

The deadband generator circuit includes three 8-bit counters and an 8-bit compare register. Desired deadband values (from 0 to 24 µs) can be programmed into the compare register for the outputs of the three compare units. The deadband generation can be enabled/disabled for each compare unit output individually. The deadband-generator circuit produces two outputs (with or without deadband zone) for each compare unit output signal. The output states of the deadband generator are configurable and changeable as needed by way of the double-buffered ACTR register.

PWM waveform generation

Up to eight PWM waveforms (outputs) can be generated simultaneously by each event manager: three independent pairs (six outputs) by the three full-compare units with

programmable deadbands

, and two

independent PWMs by the GP-timer compares.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PWM characteristics

Characteristics of the PWMs are as follows:

D 16-bit registers D Programmable deadband for the PWM output pairs, from 0 to 24 µs D Minimum deadband width of 50 ns D Change of the PWM carrier frequency for PWM frequency wobbling as needed D Change of the PWM pulse widths within and after each PWM period as needed D External-maskable power and drive-protection interrupts D Pulse-pattern-generator circuit, for programmable generation of asymmetric, symmetric, and four-space

vector PWM waveforms

D Minimized CPU overhead using auto-reload of the compare and period registers

capture unit

The capture unit provides a logging function for different events or transitions. The values of the GP timer 2 counter are captured and stored in the two-level-deep FIFO stacks when selected transitions are detected on capture input pins, CAPx (x = 1, 2, or 3 for EV A; and x = 4, 5, or 6 for EVB). The capture unit consists of three capture circuits.

D Capture units include the following features:

– One 16-bit capture control register, CAPCON (R/W) – One 16-bit capture FIFO status register, CAPFIFO (eight MSBs are read-only, eight LSBs are

write-only) – Selection of GP timer 2 as the time base – Three 16-bit 2-level-deep FIFO stacks, one for each capture unit – Three Schmitt-triggered capture input pins (CAP1, CAP2, and CAP3)—one input pin per capture unit.

[All inputs are synchronized with the device (CPU) clock. In order for a transition to be captured, the

input must hold at its current level to meet two rising edges of the device clock. The input pins CAP1 and

CAP2 can also be used as QEP inputs to the QEP circuit.] – User-specified transition (rising edge, falling edge, or both edges) detection – Three maskable interrupt flags, one for each capture unit

quadrature-encoder pulse (QEP) circuit

Two capture inputs (CAP1 and CAP2 for EVA; CAP4 and CAP5 for EVB) can be used to interface the on-chip QEP circuit with a quadrature encoder pulse. Full synchronization of these inputs is performed on-chip. Direction or leading-quadrature pulse sequence is detected, and GP timer 2 is incremented or decremented by the rising and falling edges of the two input signals (four times the frequency of either input pulse).

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

enhanced analog-to-digital converter (ADC) module

A simplified functional block diagram of the ADC module is shown in Figure 10. The ADC module consists of a 10-bit ADC with a built-in sample-and-hold (S/H) circuit. Functions of the ADC module include:

D 10-bit ADC core with built-in S/H D Fast conversion time (S/H + Conversion) of 500 ns D 16-channel, muxed inputs D Autosequencing capability provides up to 16 “autoconversions” in a single session. Each conversion can

be programmed to select any 1 of 16 input channels

D Sequencer can be operated as two independent 8-state sequencers or as one large 16-state sequencer

(i.e., two cascaded 8-state sequencers)

D Sixteen result registers (individually addressable) to store conversion values D Multiple triggers as sources for the start-of-conversion (SOC) sequence

– S/W – software immediate start – EVA – Event manager A (multiple event sources within EV A) – EVB – Event manager B (multiple event sources within EVB) – Ext – External pin (ADCSOC)

D Flexible interrupt control allows interrupt request on every end of sequence (EOS) or every other EOS D Sequencer can operate in “start/stop” mode, allowing multiple “time-sequenced triggers” to synchronize

conversions

D EVA and EVB triggers can operate independently in dual-sequencer mode D Sample-and-hold (S/H) acquisition time window has separate prescale control D Built-in calibration mode D Built-in self-test mode

The ADC module in the ’240x has been enhanced to provide flexible interface to event managers A and B. The ADC interface is built around a fast, 10-bit ADC module with total conversion time of 500 ns (S/H + conversion). The ADC module has 16 channels, configurable as two independent 8-channel modules to service event managers A and B. The two independent 8-channel modules can be cascaded to form a 16-channel module. Figure 10 shows the block diagram of the ’240x ADC module.

The two 8-channel modules have the capability to autosequence a series of conversions, each module has the choice of selecting any one of the respective eight channels available through an analog mux. In the cascaded mode, the autosequencer functions as a single 16-channel sequencer. On each sequencer, once the conversion is complete, the selected channel value is stored in its respective RESUL T register. Autosequencing allows the system to convert the same channel multiple times, allowing the user to perform oversampling algorithms. This gives increased resolution over traditional single-sampled conversion results.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

enhanced analog-to-digital converter (ADC) module (continued)

Result Registers

EVB

S/W

ADCSOC Pin

EVA

S/W

Sequencer 2

Sequencer 1

SOCSOC

ADC Control Registers

70B7h

70B0h

70AFh

70A8h

Result Reg 15

Result Reg 8

Result Reg 7

Result Reg 1

Result Reg 0

ADCIN 8

ADCIN 15

ADCIN 7

ADCIN 0

(500 ns)

Module

ADC

10-Bit

Analog MUX

Figure 10. Block Diagram of the ’240x ADC Module

controller area network (CAN) module

The CAN module is a full-CAN controller designed as a 16-bit peripheral module and supports the following features:

D CAN specification 2.0B (active)

– Standard data and remote frames – Extended data and remote frames

D Six mailboxes for objects of 0- to 8-byte data length

– Two receive mailboxes, two transmit mailboxes – Two configurable transmit/receive mailboxes

D Local acceptance mask registers for mailboxes 0 and 1 and mailboxes 2 and 3

– Configurable standard or extended message identifier

D Programmable global mask registers for objects 1 and 2 and one for object 3 and 4

– Configurable standard or extended message identifier

D Programmable bit rate D Programmable interrupt scheme D Readable error counters D Self-test mode

In this mode, the CAN module operates in a loop-back fashion, receiving its own transmitted message.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

controller area network (CAN) module (continued)

The CAN module is a 16-bit peripheral. The accesses are split into the control/status-registers accesses and the mailbox-RAM accesses.

CAN peripheral registers: The CPU can access the CAN peripheral registers only using 16-bit write accesses. The CAN peripheral always presents full 16-bit data to the CPU bus during read cycles.

CAN controller architecture

Figure 1 1 shows the basic architecture of the CAN controller through this block diagram of the CAN Peripherals.

Temporary Receive Buffer

Data

CAN Module

Control Logic

CPU Interface/

Memory Management Unit

CAN Core

Control/Status Registers

Interrupt Logic

Control Bus

Acceptance Filter

Transmit Buffer

RAM 48x16

RxD

TxD

CAN

Transceiver

Matchid

CPU

mailbox 0

mailbox 1

mailbox 2

mailbox 3

mailbox 4

mailbox 5

R R T/R T/R T T

Figure 11. CAN Module Block Diagram

The mailboxes are situated in one 48-word x 16-bit RAM. It can be written to or read by the CPU or the CAN. The CAN write or read access, as well as the CPU read access, needs one clock cycle. The CPU write access needs two clock cycles. In these two clock cycles, the CAN performs a read-modify-write cycle and, therefore, inserts one wait state for the CPU.

Address bit 0 of the address bus used when accessing the RAM decides if the lower (0) or the higher (1) 16-bit word of the 32-bit word is taken. The RAM location is determined by the upper bits 5 to 1 of the address bus.

Table 9 shows the mailbox locations in RAM. One half-word has 16 bits.

CAN interrupt logic

There are two interrupt requests from the CAN module to the peripheral interrupt expansion (PIE) controller: the mailbox interrupt and the error interrupt. Both interrupts can assert either a high-priority request or a low-priority request to the CPU. Since CAN mailboxes can generate multiple interrupts, the software should read the CAN_IFR register for every interrupt and prioritize the interrupt service, or else, these multiple interrupts will not be recognized by the CPU and PIE hardware logic. Each interrupt routine should service all the interrupt bits that are set and clear them after service.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

CAN memory map

Table 8 and Table 9 show the register and mailbox locations in the CAN module.

Table 8. Register Addresses

†

ADDRESS

OFFSET

NAME DESCRIPTION

00h MDER Mailbox Direction/Enable Register (bits 7 to 0) 01h TCR Transmission Control Register (bits 15 to 0) 02h RCR Receive Control Register (bits 15 to 0) 03h MCR Master Control Register (bits 13 to 6, 1, 0) 04h BCR2 Bit Configuration Register 2 (bits 7 to 0) 05h BCR1 Bit Configuration Register 1 (bits 10 to 0) 06h ESR Error Status Register (bits 8 to 0) 07h GSR Global Status Register (bits 5 to 0) 08h CEC Transmit and Receive Error Counters (bits 15 to 0)

09h CAN_IFR Interrupt Flag Register (bits 13 to 8, 6 to 0) 0Ah CAN_IMR Interrupt Mask Register (bits 15, 13 to 0) 0Bh LAM0_H Local Acceptance Mask Mailbox 0 and 1 (bits 31, 28 to 16) 0Ch LAM0_L Local Acceptance Mask Mailbox 0 and 1 (bits 15 to 0) 0Dh LAM1_H Local Acceptance Mask Mailbox 2 and 3 (bits 31, 28 to 16) 0Eh LAM1_L Local Acceptance Mask Mailbox 2 and 3 (bits 15 to 0)

0Fh Reserved Accesses assert the CAADDRx signal from the CAN peripheral (which asserts an Illegal Address error)

†

All unimplemented register bits are read as zero, writes have no effect. Register bits are initialized to zero, unless otherwise stated in the definition.

Table 9. Mailbox Addresses

‡

ADDRESS

OFFSET [5:0]

NAME

DESCRIPTION

UPPER HALF-WORD ADDRESS BIT 0 = 1

DESCRIPTION

LOWER HALF-WORD ADDRESS BIT 0 = 0

00h MSGID0 Message ID for mailbox 0 Message ID for mailbox 0

02h MSGCTRL0 Unused RTR and DLC (bits 4 to 0)

Databyte 0, Databyte 1 (DBO = 1) Databyte 2, Databyte 3 (DBO = 1)

04h Datalow0

Databyte 3, Databyte 2 (DBO = 0) Databyte 1, Databyte 0 (DBO = 0) Databyte 4, Databyte 5 (DBO = 1) Databyte 6, Databyte 7 (DBO = 1)

06h Datahigh0

Databyte 7, Databyte 6 (DBO = 0) Databyte 5, Databyte 4 (DBO = 0)

08h MSGID1 Message ID for mailbox 1 Message ID for mailbox 1 0Ah MSGCTRL1 Unused RTR and DLC (bits 4 to 0)

Databyte 0, Databyte 1 (DBO = 1) Databyte 2, Databyte 3 (DBO = 1)

0Ch Datalow1

Databyte 3, Databyte 2 (DBO = 0) Databyte 1, Databyte 0 (DBO = 0)

0Eh Datahigh1 Databyte 4, Databyte 5 (DBO = 1) Databyte 6, Databyte 7 (DBO = 1)

... ... ... ...

28h MSGID5 Message ID for mailbox 5 Message ID for mailbox 5 2Ah MSGCTRL5 Unused RTR and DLC (bits 4 to 0)

Databyte 0, Databyte 1 (DBO = 1) Databyte 2, Databyte 3 (DBO = 1)

2Ch Datalow5

Databyte 3, Databyte 2 (DBO = 0) Databyte 3, Databyte 2 (DBO = 0) Databyte 4, Databyte 5 (DBO = 1) Databyte 6, Databyte 7 (DBO = 1)

2Eh Datahigh5

Databyte 7, Databyte 6 (DBO = 0) Databyte 5, Databyte 4 (DBO = 0)

‡

The DBO (data byte order) bit is located in the MCR register and is used to define the order in which the data bytes are stored in the mailbox when received and the order in which the data bytes are transmitted. Byte 0 is the first byte in the message and Byte 7 is the last one shown in the CAN message.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

serial communications interface (SCI) module

The ’240x devices include a serial communications interface (SCI) module. The SCI module supports digital communications between the CPU and other asynchronous peripherals that use the standard non-return-to-zero (NRZ) format. The SCI receiver and transmitter are double-buffered, and each has its own separate enable and interrupt bits. Both can be operated independently or simultaneously in the full-duplex mode. To ensure data integrity, the SCI checks received data for break detection, parity, overrun, and framing errors. The bit rate is programmable to over 65 000 different speeds through a 16-bit baud-select register. Features of the SCI module include:

D Two external pins:

– SCITXD: SCI transmit-output pin – SCIRXD: SCI receive-input pin

NOTE: Both pins can be used as GPIO if not used for SCI.

D Baud rate programmable to 64K different rates

– Up to 1875 Kbps at 30-MHz CPUCLK

D Data-word format

– One start bit – Data-word length programmable from one to eight bits – Optional even/odd/no parity bit – One or two stop bits

D Four error-detection flags: parity, overrun, framing, and break detection D Two wake-up multiprocessor modes: idle-line and address bit D Half- or full-duplex operation D Double-buffered receive and transmit functions D Transmitter and receiver operations can be accomplished through interrupt-driven or polled algorithms with

status flags. – Transmitter: TXRDY flag (transmitter-buffer register is ready to receive another character) and

TX EMPTY flag (transmitter-shift register is empty)

– Receiver: RXRDY flag (receiver-buffer register is ready to receive another character), BRKDT flag

(break condition occurred), and RX ERROR flag (monitoring four interrupt conditions)

D Separate enable bits for transmitter and receiver interrupts (except BRKDT) D NRZ (non-return-to-zero) format D Ten SCI module control registers located in the control register frame beginning at address 7050h

NOTE: All registers in this module are 8-bit registers that are connected to the 16-bit peripheral bus. When a register is accessed, the

register data is in the lower byte (7–0), and the upper byte (15–8) is read as zeros. Writing to the upper byte has no effect.

Figure 12 shows the SCI module block diagram.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

serial communications interface (SCI) module (continued)

Internal

Clock

WUT

Frame Format and Mode

Even/Odd Enable

Parity

SCI RX Interrupt

BRKDT

SCICTL1.1

RXRDY

SCIRXST.6

SCICTL1.3

External

Connections

SCICTL2.1

RX/BK INT ENA

SCIRXD

SCIRXST.1

TXENA

SCI TX Interrupt

TX EMPTY

TXRDY

SCICTL2.0

TX INT ENA

SCITXD

RXENA

SCIRXD

RXWAKE

SCICTL1.0

SCICTL1.6

RX ERR INT ENA

TXWAKE

SCITXD

TXINT

SCICCR.6 SCICCR.5

SCITXBUF.7–0

SCIHBAUD. 15–8

Baud Rate

MSbyte

SCILBAUD. 7–0

SCIRXBUF.7–0

Receiver-Data

Buffer

SCIRXST.7

PEFE OE

RX Error

SCIRXST.4–2

Transmitter-Data

Buffer Register

SCICTL2.6

SCICTL2.7

Baud Rate

LSbyte

RXSHF

TXSHF

SCIRXST.5

RXINT

SCIPRI.5

SCIPRI.6

SCI Priority Level Level 5 Int.

Level 1 Int.

Level 5 Int. Level 1 Int.

1 0

SCI TX

Priority

SCI RX

Priority

Figure 12. Serial Communications Interface (SCI) Module Block Diagram

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

serial peripheral interface (SPI) module

Some ’240x devices include the four-pin serial peripheral interface (SPI) module. The SPI is a high-speed, synchronous serial I/O port that allows a serial bit stream of programmed length (one to sixteen bits) to be shifted into and out of the device at a programmable bit-transfer rate. Normally, the SPI is used for communications between the DSP controller and external peripherals or another processor. T ypical applications include external I/O or peripheral expansion through devices such as shift registers, display drivers, and ADCs. Multidevice communications are supported by the master/slave operation of the SPI.

The SPI module features include:

D Four external pins:

– SPISOMI: SPI slave-output/master-input pin – SPISIMO: SPI slave-input/master-output pin – SPISTE: SPI slave transmit-enable pin – SPICLK: SPI serial-clock pin

NOTE: All four pins can be used as GPIO, if the SPI module is not used.

D Two operational modes: master and slave D Baud rate: 125 different programmable rates/7.5 Mbps at 30-MHz CPUCLK D Data word length: one to sixteen data bits D Four clocking schemes (controlled by clock polarity and clock phase bits) include:

– Falling edge without phase delay: SPICLK active high. SPI transmits data on the falling edge of the

SPICLK signal and receives data on the rising edge of the SPICLK signal.

– Falling edge with phase delay: SPICLK active high. SPI transmits data one half-cycle ahead of the

falling edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal.

– Rising edge without phase delay: SPICLK inactive low. SPI transmits data on the rising edge of the

SPICLK signal and receives data on the falling edge of the SPICLK signal.

– Rising edge with phase delay: SPICLK inactive low. SPI transmits data one half-cycle ahead of the

falling edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal.

D Simultaneous receive and transmit operation (transmit function can be disabled in software) D Transmitter and receiver operations are accomplished through either interrupt-driven or polled algorithms. D Nine SPI module control registers: Located in control register frame beginning at address 7040h.

NOTE: All registers in this module are 16-bit registers that are connected to the 16-bit peripheral bus. When a register is accessed, the

register data is in the lower byte (7–0), and the upper byte (15–8) is read as zeros. Writing to the upper byte has no effect.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

serial peripheral interface (SPI) module (continued)

Figure 13 is a block diagram of the SPI in slave mode.

Clock

Polarity

Talk

Internal Clock

456

012

SPI Bit Rate

State Control

SPIRXBUF

Buffer Register

Clock

Phase

1230

Receiver

Overrun Flag

SPICTL.4

Overrun

INT ENA

SPICCR.3–0

SPIBRR.6–0

SPICCR.6 SPICTL.3

SPIRXBUF.15–0

SPIDAT.15–0

SPICTL.1

Master/Slave

SPI INT FLAG

SPICTL.0

SPI INT

ENA

SPISTS.7

SPIDAT

Data Register

SPISTS.6

SPICTL.2

SPI Char

External

Connections

SPISIMO

SPISOMI

SPISTE

†

SPICLK

SW2

SW3

To CPU

SW1

SPIPRI.6

SPI Priority

Level 1 INT

Level 5 INT

SPITXBUF.15–0

SPITXBUF

Buffer Register

NOTE A: The diagram is shown in the slave mode.

†

The SPISTE pin is shown as being disabled, meaning that data cannot be transmitted in this mode. Note that SW1, SW2, and SW3 are closed in this configuration.

Figure 13. Four-Pin Serial Peripheral Interface Module Block Diagram

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PLL-based clock module

The ’240x has an on-chip, PLL-based clock module. This module provides all the necessary clocking signals for the device, as well as control for low-power mode entry . The PLL has a 3-bit ratio control to select different CPU clock rates. See Figure 14 for the PLL Clock Module Block Diagram, T able 11 for the loop filter component values, and Table 10 for clock rates.

The PLL-based clock module provides two modes of operation:

D Crystal-operation

This mode allows the use of an external crystal/resonator to provide the time base to the device.

D External clock source operation

This mode allows the internal oscillator to be bypassed. The device clocks are generated from an external clock source input on the XTAL1/CLKIN pin. In this case, an external oscillator clock is connected to the XTAL1/CLKIN pin.

XTAL2

XTAL1/CLKIN

PLL

XTAL

OSC

CLKOUT

3-bit

PLL Select

(SCSR1.[11:9])

PLLF

RESONATOR/

CRYSTAL

PLLF2

Figure 14. PLL Clock Module Block Diagram

Table 10. PLL Clock Selection Through BIts (11–9) in SCSR1 Register

CLK PS2 CLK PS1 CLK PS0 CLKOUT

0 0 0 4 × F

0 0 1 2 × F

0 1 0 1.33 × F

0 1 1 1 × F

1 0 0 0.8 × F

1 0 1 0.66 × F

1 1 0 0.57 × F

1 1 1 0.5 × F

Default multiplication factor after reset is (1,1,1), i.e., 0.5 × Fin.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external reference crystal clock option

The internal oscillator is enabled by connecting a crystal across XTAL1/CLKIN and XTAL2 pins as shown in Figure 15a. The crystal should be in fundamental operation and parallel resonant, with an effective series resistance of 30 Ω–150 Ω and a power dissipation of 1 mW ; it should be specified at a load capacitance of 20 pF .

external reference oscillator clock option

The internal oscillator is disabled by connecting a TTL-level clock signal to XT AL1/CLKIN and leaving the XTAL2 input pin unconnected as shown in Figure 15b.

External Clock Signal

(Toggling 0–3.3 V)

(see Note A)

XTAL2XTAL1/CLKIN XTAL1/CLKIN XTAL2

Crystal

(see Note A)

(a) (b)

NOTE A: TI recommends that customers have the resonator/crystal vendor characterize the operation of their device with the DSP chip. The

resonator/crystal vendor has the equipment and expertise to tune the tank circuit. The vendor can also advise the customer regarding the proper tank component values that will ensure start-up and stability over the entire operating range.

Figure 15. Recommended Crystal/Clock Connection

loop filter

The PLL module uses an external loop filter circuit for jitter minimization. The components for the loop filter circuit are R1, C1, and C2. The capacitors (C1 and C2) must be non-polarized. This loop filter circuit is connected between the PLLF and PLLF2 pins (see Figure 14). For examples of component values of R1, C1, and C2 at a specified oscillator frequency (XTAL1), see Table 11.

Table 11. Loop Filter Component Values With Damping Factor = 2.0

XTAL1/CLKIN FREQUENCY

(MHz)

R1 (Ω) C1 (µF) C2 (µF)

4 4.7 3.9 0.082 5 5.6 2.7 0.056 6 6.8 1.8 0.039 7 8.2 1.5 0.033 8 9.1 1 0.022

9 10 0.82 0.015 10 11 0.68 0.015 11 12 0.56 0.012 12 13 0.47 0.01 13 15 0.39 0.0082 14 15 0.33 0.0068 15 16 0.33 0.0068 16 18 0.27 0.0056 17 18 0.22 0.0047 18 20 0.22 0.0047 19 22 0.18 0.0039 20 24 0.15 0.0033

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

low-power modes

The ’240x has an IDLE instruction. When executed, the IDLE instruction stops the clocks to all circuits in the CPU, but the clock output from the CPU continues to run. With this instruction, the CPU clocks can be shut down to save power while the peripherals (clocked with CLKOUT) continue to run. The CPU exits the IDLE state if it is reset, or, if it receives an interrupt request.

clock domains

All ’240x-based devices have two clock domains:

1. CPU clock domain – consists of the clock for most of the CPU logic

2. System clock domain – consists of the peripheral clock (which is derived from CLKOUT of the CPU) and the clock for the interrupt logic in the CPU.

When the CPU goes into IDLE mode, the CPU clock domain is stopped while the system clock domain continues to run. This mode is also known as IDLE1 mode. The ’240x CPU also contains support for a second IDLE mode, IDLE2. By asserting IDLE2 to the ’240x CPU, both the CPU clock domain and the system clock domain are stopped, allowing further power savings. A third low-power mode, HAL T mode, the deepest, is possible if the oscillator and WDCLK are also shut down when in IDLE2 mode.

Two control bits, LPM1 and LPM0, specify which of the three possible low-power modes is entered when the IDLE instruction is executed (see Table 12). These bits are located in the System Control and Status Register 1 (SCSR1), and they are described in the

TMS320F243/’F241/’C242 DSP Controllers System and

Peripherals User’s Guide

(literature number SPRU276).

T able 12. Low-Power Modes Summary

LOW-POWER MODE

LPMx BITS

SCSR1 [13:12]

CPU

CLOCK

DOMAIN

SYSTEM

CLOCK

DOMAIN

WDCLK STATUS

PLL

STATUS

OSC

STATUS

FLASH

POWER

EXIT

CONDITION

CPU running normally XX On On On On On On —

IDLE1 – (LPM0) 00 Off On On On On On

Peripheral

Interrupt,

External Interrupt,

Reset,

PDPINTA/B

IDLE2 – (LPM1) 01 Off Off On On On On

Wakeup

Interrupts,

External Interrupt,

Reset,

PDPINTA/B

HALT – (LPM2)

[PLL/OSC power down]

1X Off Off Off Off Off Off

Reset,

PDPINTA/B

other power-down options

’240x devices have clock enable bits to the following on-chip peripherals: ADC, SCI, SPI, CAN, EVB, and EV A. Clock to these peripherals are disabled after reset; thus, start-up power can be low for the device.

Depending on the application, these peripherals can be turned on/off to achieve low power. Refer to the SCSR2 register for details on the peripheral clock enable bits.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

digital I/O and shared pin functions

The ’240x has up to 41 general-purpose, bidirectional, digital I/O (GPIO) pins—most of which are shared between primary functions and I/O. Most I/O pins of the ’240x are shared with other functions. The digital I/O ports module provides a flexible method for controlling both dedicated I/O and shared pin functions. All I/O and shared pin functions are controlled using eight 16-bit registers. These registers are divided into two types:

D Output Control Registers — used to control the multiplexer selection that chooses between the primary

function of a pin or the general-purpose I/O function.

D Data and Control Registers — used to control the data and data direction of bidirectional I/O pins.

description of shared I/O pins

The control structure for shared I/O pins is shown in Figure 16, where each pin has three bits that define its operation:

D Mux control bit — this bit selects between the primary function (1) and I/O function (0) of the pin. D I/O direction bit — if the I/O function is selected for the pin (mux control bit is set to 0), this bit determines

whether the pin is an input (0) or an output (1).

D I/O data bit — if the I/O function is selected for the pin (mux control bit is set to 0) and the direction selected

is an input, data is read from this bit; if the direction selected is an output, data is written to this bit.

The mux control bit, I/O direction bit, and I/O data bit are in the I/O control registers.

Primary

Function

(Read/Write)

IOP Data Bit

In Out

0 = Input 1 = Output

MUX Control Bit

0 = I/O Function

1 = Primary Function

IOP DIR Bit

Primary

Function

or I/O Pin

Figure 16. Shared Pin Configuration

A summary of shared pin configurations and associated bits is shown in Table 13.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

description of shared I/O pins (continued)

Table 13. Shared Pin Configurations

†

PIN FUNCTION SELECTED

MUX

I/O PORT DATA AND DIRECTION

‡

(MCRx.n = 1)

Primary

Function

(MCRx.n = 0)

I/O

MUX

CONTROL

(name.bit #)

CONTROL VALUE AT

RESET

(MCRx.n)

DATA

BIT NO.

DIR BIT

NO.

PORT A

SCITXD IOPA0 MCRA.0 0 PADATDIR 0 8

SCIRXD IOPA1 MCRA.1 0 PADATDIR 1 9

XINT1 IOPA2 MCRA.2 0 PADATDIR 2 10 CAP1/QEP1 IOPA3 MCRA.3 0 PADATDIR 3 11 CAP2/QEP2 IOPA4 MCRA.4 0 PADATDIR 4 12

CAP3 IOPA5 MCRA.5 0 PADATDIR 5 13 PWM1 IOPA6 MCRA.6 0 PADATDIR 6 14 PWM2 IOPA7 MCRA.7 0 PADATDIR 7 15

PORT B

PWM3 IOPB0 MCRA.8 0 PBDATDIR 0 8 PWM4 IOPB1 MCRA.9 0 PBDATDIR 1 9 PWM5 IOPB2 MCRA.10 0 PBDATDIR 2 10 PWM6 IOPB3 MCRA.11 0 PBDATDIR 3 11

T1PWM/T1CMP IOPB4 MCRA.12 0 PBDATDIR 4 12 T2PWM/T2CMP IOPB5 MCRA.13 0 PBDATDIR 5 13

TDIRA IOPB6 MCRA.14 0 PBDATDIR 6 14

TCLKINA IOPB7 MCRA.15 0 PBDATDIR 7 15

PORT C

W/R

IOPC0 MCRB.0 1 PCDATDIR 0 8

BIO

IOPC1 MCRB.1 1 PCDATDIR 1 9 SPISIMO IOPC2 MCRB.2 0 PCDATDIR 2 10 SPISOMI IOPC3 MCRB.3 0 PCDATDIR 3 11

SPICLK IOPC4 MCRB.4 0 PCDATDIR 4 12 SPISTE IOPC5 MCRB.5 0 PCDATDIR 5 13

CANTX IOPC6 MCRB.6 0 PCDATDIR 6 14

CANRX IOPC7 MCRB.7 0 PCDATDIR 7 15

PORT D

XINT2/ADCSOC IOPD0 MCRB.8 0 PDDATDIR 0 8

EMU0

Reserved MCRB.9 1 PDDATDIR 1 9

EMU1

Reserved MCRB.10 1 PDDATDIR 2 10

TCK

Reserved MCRB.11 1 PDDATDIR 3 11

TDI

Reserved MCRB.12 1 PDDATDIR 4 12

TDO

Reserved MCRB.13 1 PDDATDIR 5 13

TMS

Reserved MCRB.14 1 PDDATDIR 6 14

TMS2

Reserved MCRB.15 1 PDDATDIR 7 15

†

Bold, italicized pin names indicate pin functions at reset.

‡

Valid only if the I/O function is selected on the pin

If the GPIO pin is configured as an output, these bits can be written to. If the pin is configured as an input, these bits are read from.

If the DIR bit is 0, the GPIO pin functions as an input. For a value of 1, the pin is configured as an output.

At reset, ’LF2406 and ’LF2402 come up in W/R

mode. Application software should select this pin to be IOPC0.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

description of shared I/O pins (continued)

Table 13. Shared Pin Configurations† (Continued)

PIN FUNCTION SELECTED

MUX

I/O PORT DATA AND DIRECTION

‡

(MCRx.n = 1)

Primary

Function

(MCRx.n = 0)

I/O

MUX

CONTROL REGISTER

(name.bit #)

CONTROL VALUE AT

RESET

(MCRx.n)

DATA

BIT NO.

DIR BIT

NO.

PORT E

CLKOUT IOPE0 MCRC.0 1 PEDATDIR 0 8

PWM7 IOPE1 MCRC.1 0 PEDATDIR 1 9 PWM8 IOPE2 MCRC.2 0 PEDATDIR 2 10

PWM9 IOPE3 MCRC.3 0 PEDATDIR 3 11 PWM10 IOPE4 MCRC.4 0 PEDATDIR 4 12 PWM11 IOPE5 MCRC.5 0 PEDATDIR 5 13 PWM12 IOPE6 MCRC.6 0 PEDATDIR 6 14

CAP4/QEP3 IOPE7 MCRC.7 0 PEDATDIR 7 15

PORT F

CAP5/QEP4 IOPF0 MCRC.8 0 PFDATDIR 0 8

CAP6 IOPF1 MCRC.9 0 PFDATDIR 1 9 T3PWM/T3CMP IOPF2 MCRC.10 0 PFDATDIR 2 10 T4PWM/T4CMP IOPF3 MCRC.11 0 PFDATDIR 3 11

TDIRB IOPF4 MCRC.12 0 PFDATDIR 4 12

TCLKINB IOPF5 MCRC.13 0 PFDATDIR 5 13

IOPF6 IOPF6 MCRC.14 0 PFDATDIR 6 14

†

Bold, italicized pin names indicate pin functions at reset.

‡

Valid only if the I/O function is selected on the pin

If the GPIO pin is configured as an output, these bits can be written to. If the pin is configured as an input, these bits are read from.

If the DIR bit is 0, the GPIO pin functions as an input. For a value of 1, the pin is configured as an output.

digital I/O control registers

Table 14 lists the registers available in the digital I/O module. As with other ’240x peripherals, these registers are memory-mapped to the data space.

Table 14. Addresses of Digital I/O Control Registers

ADDRESS REGISTER NAME

7090h MCRA I/O mux control register A 7092h MCRB I/O mux control register B 7094h MCRC I/O mux control register C 7095h PEDATDIR I/O port E data and direction register 7096h PFDATDIR I/O port F data and direction register 7098h PADATDIR I/O port A data and direction register 709Ah PBDATDIR I/O port B data and direction register 709Ch PCDA TDIR I/O port C data and direction register 709Eh PDDATDIR I/O port D data and direction register

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external memory interface (’LF2407)

The TMS320LF2407 can address up to 64K × 16 words of memory (or registers) in each of the program, data, and I/O spaces. On-chip memory, when enabled, occupies some of this off-chip range.

The CPU of the TMS320LF2407 schedules a program fetch, data read, and data write on the same machine cycle. This is because from on-chip memory, the CPU can execute all three of these operations in the same cycle. However, the external interface multiplexes the internal buses to one address bus and one data bus. The external interface sequences these operations to complete first the data write, then the data read, and finally the program read.

The ’LF2407 supports a wide range of system interfacing requirements. Program, data, and I/O address spaces provide interface to memory and I/O, thereby maximizing system throughput. The full 16-bit address and data buses, along with the PS

, DS, and IS space-select signals, allow addressing of 64K 16-bit words in program, data, and I/O space. Since on-chip peripheral registers occupy positions of data-memory space (7000–7FFF), the externally addressable data-memory space is 32K 16-bit words (8000–FFFF). Note that the global memory space of the ’C2xx core is not used for ’240x DSP devices. Therefore, the global memory allocation register (GREG) is reserved for all these devices.

Input/output (I/O) design is simplified by having I/O space treated the same way as memory. I/O devices are accessed in the I/O address space using the processor’s external address and data buses in the same manner as memory-mapped devices.

The ’LF2407 external parallel interface provides various control signals to facilitate interfacing to the device. The R/W

output signal is provided to indicate whether the current cycle is a read or a write. The STRB output signal provides a timing reference for all external cycles. For convenience, the device also provides the RD and the WE output signals, which indicate a read cycle and a write cycle, respectively , along with timing information for those cycles. The availability of these signals minimizes external gating necessary for interfacing external devices to the ’LF2407.

The ’2407 provides RD and W/R signals to help the zero-wait-state external memory interface. At higher CLKOUT speeds, RD may not meet the slow memory device’s timing. In such instances, the W/R signal could be used as an alternative signal with some tradeoffs. See the timings for details.

The TMS320LF2407 supports zero-wait-state reads on the external interface. However, to avoid bus conflicts, writes take two cycles. This allows the TMS320LF2407 to buffer the transition of the data bus from input to output (or from output to input) by a half cycle. In most systems, the TMS320LF2407 ratio of reads to writes is significantly large to minimize the overhead of the extra cycle on writes.

wait-state generation (’LF2407 only)

Wait-state generation is incorporated in the ’LF2407 without any external hardware for interfacing the ’LF2407 with slower off-chip memory and I/O devices. Adding wait states lengthens the time the CPU waits for external memory or an external I/O port to respond when the CPU reads from or writes to that external memory or I/O port. Specifically, the CPU waits one extra cycle (one CLKOUT cycle) for every wait state. The wait states operate on CLKOUT cycle boundaries.

To avoid bus conflicts, writes from the ’LF2407 always take at least two CLKOUT cycles. The ’LF2407 offers two options for generating wait states:

D READY Signal. With the READY signal, you can externally generate any number of wait states. The READY

pin has no effect on accesses to

internal

memory.

D On-Chip Wait-State Generator. With this generator, you can generate zero to seven wait states.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

generating wait states with the READY signal

When the READY signal is low, the ’LF2407 waits one CLKOUT cycle and then checks READY again. The

’LF2407 does not continue executing until the READY signal is driven high; therefore, if the READY signal is

not used, it should be pulled high.

The READY pin can be used to generate any number of wait states. However, when the ’LF2407 operates at

full speed, it may not respond fast enough to provide a READY -based wait state for the first cycle. For extended

wait states using external READY logic, the on-chip wait-state generator should be programmed to generate

at least one wait state.

generating wait states with the ’LF2407 on-chip software wait-state generator

The software wait-state generator can be programmed to generate zero to seven wait states for a given off-chip

memory space (program, data, or I/O), regardless of the state of the READY signal. These zero to seven wait

states are controlled by the wait-state generator register (WSGR) (I/O FFFFh). For more detailed information

on the WSGR and associated bit functions, refer to the

TMS320F243/’F241/’C242 DSP Controllers System and

Peripherals User’s Guide

(literature number SPRU276).

watchdog (WD) timer module

The ’x240x devices include a watchdog (WD) timer module. The WD function of this module monitors software

and hardware operation by generating a system reset if it is not periodically serviced by software by having the

correct key written. The WD timer operates independently of the CPU. It does not need any CPU initialization

to function. When a system reset occurs, the WD timer defaults to the fastest WD timer rate available (WDCLK

signal = CLKOUT/512). As soon as reset is released internally , the CPU starts executing code, and the WD timer

begins incrementing. This means that, to avoid a premature reset, WD setup should occur early in the power-up

sequence. See Figure 17 for a block diagram of the WD module. The WD module features include the following:

D WD Timer

– Seven different WD overflow rates – A WD-reset key (WDKEY) register that clears the WD counter when a correct value is written, and

generates a system reset if an incorrect value is written to the register

– WD check bits that initiate a system reset if an incorrect value is written to the WD control register

(WDCR)

D Automatic activation of the WD timer, once system reset is released

– Three WD control registers located in control register frame beginning at address 7020h.

NOTE: All registers in this module are 8-bit registers. When a register is accessed, the register data is in the lower byte, the upper byte

is read as zeros. Writing to the upper byte has no effect.

Figure 17 shows the WD block diagram. Table 15 shows the different WD overflow (timeout) selections.

The watchdog can be disabled in software by writing ’1’ to bit 6 of the WDCR register (WDCR.6) while bit 5 of

the SCSR2 register (SCSR2.5) is 1. If SCSR2.5 is 0, the watchdog will not be disabled. SCSR2.5 is equivalent

to the WDDIS pin of the TMS320F243/241 devices.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

watchdog (WD) timer module (continued)

55 + AA

Detector

System Reset Request

WDCNTR.7–0

6-Bit

Free-

Running

Counter

/64 /32 /16 /8 /4 /2

111

110

101

100

011

010

001

000

WDCLK

System

Reset

System Reset

CLR

One-Cycle

Delay

Watchdog Reset Key

8-Bit Watchdog

Counter

CLR

Bad WDCR Key

Good Key

Bad Key

WDPS

WDCR.2–0

210

WDKEY.7–0

WDCHK2–0

WDCR.5–3

†

WDCR.7

WDFLAG

Reset Flag

PS/257

WDDIS

WDCR.6

101

(Constant

Value)

3 3

On-Chip

Oscillator or

External

Clock

÷ 512 PLL

CLKOUT CLKIN

3-bit

Prescaler

†

Writing to bits WDCR.5–3 with anything but the correct pattern (101) generates a system reset.

Figure 17. Block Diagram of the WD Module

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

watchdog (WD) timer module (continued)

Table 15. WD Overflow (Timeout) Selections

WD PRESCALE SELECT BITS

WDCLK DIVIDER

WATCHDOG

CLOCK RATE

†

WDPS2 WDPS1 WDPS0

WDCLK DIVIDER

FREQUENCY (Hz)

0 0 X

‡

1 WDCLK/1 0 1 0 2 WDCLK/2 0 1 1 4 WDCLK/4 1 0 0 8 WDCLK/8 1 0 1 16 WDCLK/16 1 1 0 32 WDCLK/32 1 1 1 64 WDCLK/64

†

WDCLK = CLKOUT/512

‡

X = Don’t care

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

development support

T exas Instruments (TI) offers an extensive line of development tools for the ’x240x generation of DSPs, including tools to evaluate the performance of the processors, generate code, develop algorithm implementations, and fully integrate and debug software and hardware modules.

The following products support development of ’x240x-based applications:

Software Development Tools:

Assembler/linker Simulator Optimizing ANSI C compiler Application algorithms C/Assembly debugger and code profiler

Hardware Development T ools:

Emulator XDS510 (supports ’x24x multiprocessor system debug) The

TMS320 DSP Development Support Reference Guide

(literature number SPRU01 1) contains information about development support products for all TMS320 family member devices, including documentation. Refer to this document for further information about TMS320 documentation or any other TMS320 support products from Texas Instruments. There is also an additional document, the

TMS320 Third-Party Support Reference

Guide

(literature number SPRU052), which contains information about TMS320-related products from other companies in the industry . To receive copies of TMS320 literature, contact the Literature Response Center at 800/477-8924.

See Table 16 and Table 17 for complete listings of development support tools for the ’x240x. For information on pricing and availability, contact the nearest TI field sales office or authorized distributor.

Table 16. Development Support Tools

DEVELOPMENT TOOL PLATFORM PART NUMBER

Software

Compiler/Assembler/Linker SPARC TMDS3242555-08 Compiler/Assembler/Linker PC-DOS TMDS3242855-02 Assembler/Linker PC-DOS, OS/2 TMDS3242850-02 ’C2xx Simulator PC-DOS, WIN TMDX324x851-02 ’C2xx Simulator SPARC TMDX324x551-09 Digital Filter Design Package PC-DOS DFDP ’C2xx Debugger/Emulation Software PC-DOS, OS/2, WIN TMDX324012xx ’C2xx Debugger/Emulation Software SPARC TMDX324062xx

Hardware

XDS510XL Emulator PC-DOS, OS/2 TMDS00510 XDS510WS Emulator SPARC TMDS00510WS

ADVANCE

INFORMATION

SPARC is a trademark of SPARC International, Inc. PC-DOS and OS/2 are trademarks of International Business Machines Corp. WIN is a trademark of Microsoft Corp. XDS510XL and XDS510WS are trademarks of Texas Instruments Incorporated.

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

development support (continued)

Table 17. TMS320x24x-Specific Development Tools

DEVELOPMENT TOOL PLATFORM PART NUMBER

Hardware

TMS320F240 EVM PC TMDX326P124x TMS320F243 EVM PC TMDS3P604030

The ’F240 and ’F243 Evaluation Modules (EVM) provide designers of motor and motion control applications with a complete and cost-effective way to take their designs from concept to production. These tools offer both a hardware and software development environment and include:

D Flash-based ’24x evaluation board D Code Generation Tools D Assembler/Linker D C Compiler (’F243 EVM) D Source code debugger D ’C24x Debugger (’F240 EVM) D Code Composer IDE (’F243 EVM) D XDS510PP JT AG-based emulator D Sample applications code D Universal 5VDC power supply D Documentation and cables

device and development support tool nomenclature

To designate the stages in the product development cycle, Texas Instruments assigns prefixes to the part numbers of all TMS320 devices and support tools. Each TMS320 member has one of three prefixes: TMX, TMP , or TMS. Texas Instruments recommends two of three possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from engineering prototypes (TMX/TMDX) through fully qualified production devices/tools (TMS/TMDS). This development flow is defined below.

Support tool development evolutionary flow:

TMDX Development support product that has not completed TI’s internal qualification testing TMDS Fully qualified development support product

TMX and TMP devices and TMDX development support tools are shipped against the following disclaimer: “Developmental product is intended for internal evaluation purposes.” TMS devices and TMDS development support tools have been fully characterized, and the quality and reliability

of the device have been fully demonstrated. TI’s standard warranty applies.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

device and development support tool nomenclature (continued)

TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type (for example, PG, PGE, and PZ) and temperature range (for example, A). Figure 18 provides a legend for reading the complete device name for any TMS320x2xx family member. Refer to the timing section for specific options that are available on ’240x devices.

Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production devices. T exas Instruments recommends that these devices not be used in any production system because their expected end-use failure rate still is undefined. Only qualified production devices are to be used.

PREFIX

TEMPERATURE RANGE (DEFAULT: 0°C TO 70°C)

TMS 320 LF 2407 PGE (A)

TMX = experimental device TMP = prototype device TMS = qualified device

DEVICE FAMILY

320 = TMS320 Family

TECHNOLOGY

L=0°C to 70°C A=–40°C to 85°C S=–40°C to 125°C Q=–40°C to 125°C, Q 100 Fault Grading

PACKAGE TYPE

†

PG = 64-pin PQFP PGE= 144-pin plastic TQFP PZ = 100-pin plastic TQFP

C = CMOS E = CMOS EPROM F = Flash EEPROM LC = Low-voltage CMOS (3.3 V) LF = Flash EEPROM (3.3 V) VC= Low-voltage CMOS (3 V)

DEVICE

’20x DSP

203 206 209

’24x DSP

240 241 242 243

’240x DSP

2407 2406 2404 2402

†

PQFP = Plastic Quad Flatpack TQFP = Thin Quad Flatpack

Figure 18. TMS320 Device Nomenclature

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

documentation support

Extensive documentation supports all of the TMS320 family generations of devices from product announcement through applications development. The types of documentation available include: data sheets, such as this document, with design specifications; complete user’s guides for all devices and development support tools; and hardware and software applications. Useful reference documentation includes:

D Data sheets

–

TMS320C242 DSP Controller

(literature number SPRS063)

–

TMS320F243, TMS320F241 DSP Controllers

(literature number SPRS064)

D User Guides

–

TMS320C240 DSP Controllers CPU, System, and Instruction Set Reference Guide

(literature number SPRU160)

–

TMS320C240 DSP Controllers Peripheral Library and Specific Devices

(literature number SPRU161)

–

’F243/’F241/’C242 DSP Controllers System and Peripherals User’s Guide

(literature number SPRU276)

D Application Reports

–

3.3V DSP for Digital Motor Control

(literature number SPRA550)

A series of DSP textbooks is published by Prentice-Hall and John Wiley & Sons to support digital signal processing research and education. The TMS320 newsletter,

Details on Signal Processing

, is published

quarterly and distributed to update TMS320 customers on product information. Updated information on the TMS320 DSP controllers can be found on the worldwide web at: http://www.ti.com. To send comments regarding the ’240x data sheet (SPRS094), use the

comments@books.sc.ti.com

email address, which is a repository for feedback. For questions and support, contact the Product Information Center listed at the http://www.ti.com/sc/docs/pic/home.htm site.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)

†

Supply voltage range, VDD, PLLV

CCA

, V

DDO

, and V

CCA

(see Note 1) – 0.3 V to 4.6 V. . . . . . . . . . . . . . . . . .

CCP

range 0.3 V to 5.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input voltage range, VI – 0.3 V to 4.6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output voltage range, VO ’LF240x – 0.3 V to 4.6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output voltage range,VO ’LC240x – 0.3 V to 4.6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input clamp current, I

(VI < 0 or VI > VCC) ± 20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output clamp current, IOK (VO < 0 or VO > VCC) ± 20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating free-air temperature range, TA: A version – 40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

(TMS320LF2407PGE) (TMS320LF2406PZ, TMS320LC2404PZ, TMS320LC2406PZ) (TMS320LF2402PG, TMS320LC2402PG)

S version – 40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

(TMS320LF2407PGE) (TMS320LF2406PZ, TMS320LC2404PZ, TMS320LC2406PZ) (TMS320LF2402PG, TMS320LC2402PG)

Storage temperature range, T

stg

– 65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

†

Clamp current stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTE 1: All voltage values are with respect to VSS.

recommended operating conditions

‡

MIN NOM MAX UNIT

Supply voltage (±10% of 3.3 V) 3.3-V operation 3.0 3.3 3.6 V

Supply ground 0 0 0 V

PLLV

CCA

PLL supply voltage 3.3-V operation 3.0 3.3 3.6 V

CCA

ADC supply voltage 3.3-V operation 3.0 3.3 3.6 V

CCP

Flash programming supply voltage (±5%) 4.75 5.0 5.25 V

CLKOUT

Device clock frequency – 40°C to 125°C 30 MHz

High-level input voltage All inputs 2.0 V

Low-level input voltage All inputs 0.8 V

Output pins Group 1

– 2.0 mA

High-level output source current, VOH = 2.4 V

Output pins Group 2

– 4.0 mA

IOHHigh level out ut source current, V

2.4 V

Output pins Group 3

– 8.0 mA

Output pins Group 1

2.0 mA

Low-level output sink current, VOL = VOL MAX

Output pins Group 2

4.0 mA

IOLLow level out ut sink current, V

MAX

Output pins Group 3

8.0 mA

Operating free-air temperature

A version – 40 25 85

O erating free air tem erature

(excluding flash programming)

S version

– 40 25 125

°C

stg

Storage temperature – 65 150 °C

Flash programming temperature – 40 25 85 °C

Junction temperature – 40 25 150 °C

Nf Flash endurance for the array (Write/erase cycles) At room temperature 10K cycles

‡

Refer to the mechanical data package page for thermal resistance values, ΘJA (junction-to-ambient) and ΘJC (junction-to-case).

Primary signals and their GPIOs: Group 1: PWM1–PWM6, CAP1–CAP6, TCLKINA, RS

, IOPF6, IOPC1, TCK, TDI, TMS, XF

Group 2: PS

/DS/IS, RD, W/R, STRB, R/W, VIS_OE, A0–A15, D0–D15, T1PWM–T4PWM, PWM7–PWM12, CANTX, CANRX, SPICLK,

SPISOMI, SPISIMO, SPISTE, EMU0, EMU1, TDO, TMS2

Group 3: TDIRA, TDIRB, SCIRXD, SCITXD, XINT1, XINT2, CLKOUT

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VDD = 3.0V , IOH = 2 mA, 4 mA, 8 mA 2.4

High-level output voltage

All outputs at 50 µA

2.7

Low-level output voltage IOL = 2 mA, 4 mA, 8 mA 0.4 V

Input current (low level) VI = 0 V ±20 µA

Input current (high level) VI = V

±20 µA

Output current, high-impedance state (off-state)

VO = VDD or 0 V ±5 µA

’LF2407 180

Supply current, operating mode

3.3-V operation,CPUCLK = 30 MHz, p

’LF2406 150

Su ly current, o erating mode

all peripherals running

’LF2402 115

’LF2407 80

Supply current, Idle 1 low-power

LPM0†3.3-V operation, t

c(CO

)

= 30 MHz

†

’LF2406 70

mode

LPM0

†

3.3 V o eration, t

c(CO)

MHz

†

’LF2402 55

’LF2407 45

Supply current, Idle 2 low-power

LPM1†3.3-V operation, t

(CO)

= 30 MHz

†

’LF2406 45

mode

LPM1

†

3.3 V o eration, t

c(CO)

MHz

†

’LF2402 45

’LF2407 80

Supply current,

LPM2

†

3.3-V operation, at room

†

’LF2406 80

µA

PLL/OSC

power-down mode

LPM2

†

emperature

†

’LF2402 80

µA

Input capacitance 2 pF

Output capacitance 3 pF

†

Test condition: These current measurements are estimates when the CPU is running a dummy code in B0 RAM.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PARAMETER MEASUREMENT INFORMATION

Tester Pin

Electronics

LOAD

Output Under Test

50 Ω

Where: I

= 2 mA (all outputs)

= 300 µA (all outputs)

LOAD

= 1.5 V

= 50-pF typical load-circuit capacitance

Figure 19. Test Load Circuit

signal transition levels

The data in this section is shown for the 3.3-V version. Note that some of the signals use different reference voltages, see the recommended operating conditions table. Output levels are driven to a minimum logic-high level of 2.4 V and to a maximum logic-low level of 0.8 V.

Figure 20 shows output levels.

0.4 V (VOL)

20%

2.4 V (VOH) 80%

Figure 20. Output Levels

Output transition times are specified as follows:

D For a

high-to-low transition

, the level at which the output is said to be no longer high is below 80% of the total voltage range and lower and the level at which the output is said to be low is 20% of the total voltage range and lower.

D For a

low-to-high transition

, the level at which the output is said to be no longer low is 20% of the total voltage range and higher and the level at which the output is said to be high is 80% of the total voltage range and higher.

Figure 21 shows the input levels.

0.8 V (VIL)

10%

2.0 V (VIH) 90%

Figure 21. Input Levels

Input transition times are specified as follows:

D For a

high-to-low transition

on an input signal, the level at which the input is said to be no longer high is 90% of the total voltage range and lower and the level at which the input is said to be low is 10% of the total voltage range and lower.

D For a

low-to-high transition

on an input signal, the level at which the input is said to be no longer low is 10% of the total voltage range and higher and the level at which the input is said to be high is 90% of the total voltage range and higher.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PARAMETER MEASUREMENT INFORMATION

timing parameter symbology

Timing parameter symbols used are created in accordance with JEDEC Standard 100-A. To shorten the symbols, some of the pin names and other related terminology have been abbreviated as follows:

A A[15:0] MS Memory strobe pins IS, DS, or PS Cl XTAL1/CLKIN R READY CO CLKOUT RD Read cycle or RD D D[15:0] RS RESET pin RS INT NMI, XINT1, XINT2 W Write cycle or WE

Lowercase subscripts and their meanings: Letters and symbols and their meanings: a access time H High c cycle time (period) L Low d delay time V Valid f fall time X Unknown, changing, or don’t care level h hold time Z High impedance r rise time su setup time t transition time v valid time w pulse duration (width)

general notes on timing parameters

All output signals from the ’F243/’F241 devices (including CLKOUT) are derived from an internal clock such that all output transitions for a given half-cycle occur with a minimum of skewing relative to each other.

The signal combinations shown in the following timing diagrams may not necessarily represent actual cycles. For actual cycle examples, refer to the appropriate cycle description section of this data sheet.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external reference crystal/clock with PLL circuit enabled

timings with the PLL circuit enabled

PARAMETER MIN TYP MAX UNIT

Resonator 4 13

Input clock frequency

†

Crystal

4 20

MHz

In ut clock frequency

†

CLKIN 4 20

MHz

†

Input frequency should be adjusted (CLK PS bits in SCSR1 register) such that CLKOUT = 30 MHz maximum.

switching characteristics over recommended operating conditions [H = 0.5 t

c(CO)

] (see Figure 22)

PARAMETER PLL MODE MIN TYP MAX UNIT

c(CO)

Cycle time, CLKOUT

×4 mode

†

33 ns

f(CO)

Fall time, CLKOUT 4 ns

r(CO)

Rise time, CLKOUT 4 ns

w(COL)

Pulse duration, CLKOUT low H–3 H H+3 ns

w(COH)

Pulse duration, CLKOUT high H–3 H H+3 ns

Transition time, PLL synchronized after RS pin high

4096t

c(Cl)

†

Input frequency should be adjusted (CLK PS bits in SCSR1 register) such that CLKOUT = 30 MHz maximum.

timing requirements (see Figure 22)

MIN MAX UNIT

c(Cl)

Cycle time, XTAL1/CLKIN

133 ns

f(Cl)

Fall time, XTAL1/CLKIN 5 ns

r(Cl)

Rise time, XTAL1/CLKIN 5 ns

w(CIL)

Pulse duration, XTAL1/CLKIN low as a percentage of t

c(Cl)

40 60 %

w(CIH)

Pulse duration, XTAL1/CLKIN high as a percentage of t

c(Cl)

40 60 %

XTAL1/CLKIN

c(CI)

w(CIL)

w(CIH)

f(Cl)

r(Cl)

c(CO)

w(COH)

w(COL)

r(CO)

f(CO)

CLKOUT

Figure 22. CLKIN-to-CLKOUT Timing with PLL and External Clock in ×4 Mode

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

RS timings switching characteristics over recommended operating conditions for a reset [H = 0.5t

c(CO)

]

(see Figure 23)

PARAMETER MIN MAX UNIT

w(RSL1)

Pulse duration, RS low

†

128t

c(CI)

d(EX)

Delay time, reset vector executed after PLL lock time

36H ns

PLL lock time (input cycles)

4096 cycles

†

The parameter t

w(RSL1)

refers to the time RS is an output.

A0–A15

CLKOUT

XTAL1/

CLKIN

w(RSL1)

d(EX)

Figure 23. Watchdog Reset Pulse

timing requirements for a reset [H = 0.5t

c(CO)

] (see Figure 24)

MIN MAX UNIT

w(RSL)

Pulse duration, RS low

‡

1 ms

w(RSL2)

Pulse duration, RS low

c(CI)

d(EX)

Delay time, reset vector executed after PLL lock time

36H ns

‡

The parameter t

w(RSL)

refers to the time RS is an input

A0–A15

CLKOUT

XTAL1/

CLKIN

w(RSL)

d(EX)

Case A. Power-on reset

†

XTAL1/

CLKIN

A0–A15

w(RSL2)

Case B. External reset after power-on

†

Vop is the VCC voltage below which the device is non-operational, typically around 1.1 V .

CLKOUT

d(EX)

Figure 24. Reset Timing

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

XF, BIO, and MP/MC timings

switching characteristics over recommended operating conditions (see Figure 25)

PARAMETER MIN MAX UNIT

d(XF)

Delay time, CLKOUT high to XF high/low

–3 7 ns

timing requirements (see Figure 25)

MIN MAX UNIT

su(BIO)CO

Setup time, BIO or MP/MC low before CLKOUT low

0 ns

h(BIO)CO

Hold time, BIO or MP/MC low after CLKOUT low

19 ns

d(XF)

BIO

MP/MC

CLKOUT

su(BIO)CO

h(BIO)CO

Figure 25. XF and BIO Timing

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

TIMING EVENT MANAGER INTERFACE

PWM timings

PWM refers to PWM outputs on PWM1, PWM2, PWM3, PWM4, PWM5, PWM6, T1PWM, and T2PWM.

switching characteristics over recommended operating conditions for PWM timing [H = 0.5t

c(CO)

] (see Figure 26)

PARAMETER MIN MAX UNIT

w(PWM)

†

Pulse duration, PWM output high/low

2H+5 ns

d(PWM)CO

Delay time, CLKOUT low to PWM output switching

15 ns

†

PWM outputs may be 100%, 0%, or increments of t

c(CO)

with respect to the PWM period.

timing requirements‡ [H = 0.5t

c(CO)

] (see Figure 27)

MIN MAX UNIT

w(TMRDIR)

Pulse duration, TMRDIR low/high

4H+5 ns

w(TMRCLK)

Pulse duration, TMRCLK low as a percentage of TMRCLK cycle time

40 60 %

wh(TMRCLK)

Pulse duration, TMRCLK high as a percentage of TMRCLK cycle time

40 60 %

c(TMRCLK)

Cycle time, TMRCLK

4  t

c(CO)

‡

Parameter TMRDIR is equal to the pin TDIR, and parameter TMRCLK is equal to the pin TCLKIN.

w(PWM)

d(PWM)CO

PWMx

CLKOUT

Figure 26. PWM Output Timing

CLKOUT

w(TMRDIR)

TMRDIR

Figure 27. Capture/TMRDIR Timing

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

capture and QEP timings

CAP refers to CAP1/QEP0/IOPA3, CAP2/QEP1/IOPA4, and CAP3/IOPA5.

timing requirements [H = 0.5t

c(CO)

] (see Figure 28)

MIN MAX UNIT

w(CAP)

Pulse duration, CAP input low/high

4H +15 ns

CAPx

w(CAP)

CLKOUT

Figure 28. Capture Input and QEP Timing

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

interrupt timings

INT refers to NMI, XINT1, and XINT2/IO. PDP refers to PDPINT.

switching characteristics over recommended operating conditions (see Figure 29)

PARAMETER MIN MAX UNIT

hz(PWM)PDP

Delay time, PDPINT low to PWM to high-impedance state

12 ns

d(INT)

Delay time, INT low/high to interrupt-vector fetch

10t

c(CO)

timing requirements [H = 0.5t

c(CO)

] (see Figure 29)

MIN MAX UNIT

w(INT)

Pulse duration, INT input low/high

2H+15 ns

w(PDP)

Pulse duration, PDPINT input low

4H+5 ns

PWM

PDPINT

CLKOUT

w(PDP)

hz(PWM)PDP

XINT1/XINT2/NMI

w(INT)

ADDRESS

Interrupt Vector

d(INT)

Figure 29. Power Drive Protection Interrupt Timing

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

general-purpose input/output timings

switching characteristics over recommended operating conditions (see Figure 30)

PARAMETER MIN MAX UNIT

(

GPO)CO

Delay time, CLKOUT low to GPIO low/high

All GPIOs

9ns

r(GPO)

Rise time, GPIO switching low to high All GPIOs 8 ns

f(GPO)

Fall time, GPIO switching high to low All GPIOs 6 ns

timing requirements [H = 0.5t

c(CO)

] (see Figure 31)

MIN MAX UNIT

w(GPI)

Pulse duration, GPI high/low

2H+15 ns

d(GPO)CO

GPIO

CLKOUT

r(GPO)

f(GPO)

Figure 30. General-Purpose Output Timing

GPIO

CLKOUT

w(GPI)

Figure 31. General-Purpose Input Timing

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443

• 73

SPI MASTER MODE TIMING PARAMETERS

SPI master mode timing information is listed in the following tables.

SPI master mode external timing parameters (clock phase = 0)†‡ (see Figure 32)

NO.

SPI WHEN (SPIBRR + 1) IS EVEN

OR SPIBRR = 0 OR 2

SPI WHEN (SPIBRR + 1)

IS ODD AND SPIBRR > 3

UNIT

MIN MAX MIN MAX

UNIT

1 t

c(SPC)M

Cycle time, SPICLK 4t

c(CO)

128t

c(CO)

127t

c(CO)

w(SPCH)M

Pulse duration, SPICLK high (clock polarity = 0)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

–0.5t

c(CO)

–10 0.5t

c(SPC)M

– 0.5t

c(CO)

w(SPCL)M

Pulse duration, SPICLK low (clock polarity = 1)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

–0.5t

c(CO)

–10 0.5t

c(SPC)M

–0.5t

c(CO)

w(SPCL)M

Pulse duration, SPICLK low (clock polarity = 0)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

+0.5t

c(CO)

–10 0.5t

c(SPC)M

+ 0.5t

c(CO)

w(SPCH)M

Pulse duration, SPICLK high (clock polarity = 1)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

+0.5t

c(CO)

–10 0.5t

c(SPC)M

+ 0.5t

c(CO)

d(SPCH-SIMO)M

Delay time, SPICLK high to SPISIMO valid (clock polarity = 0)

– 10 10 – 10 10

d(SPCL-SIMO)M

Delay time, SPICLK low to SPISIMO valid (clock polarity = 1)

– 10 10 – 10 10

v(SPCL-SIMO)M

Valid time, SPISIMO data valid after SPICLK low (clock polarity =0)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

+0.5t

c(CO)

–10

v(SPCH-SIMO)M

Valid time, SPISIMO data valid after SPICLK high (clock polarity =1)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

+0.5t

c(CO)

–10

su(SOMI-SPCL)M

Setup time, SPISOMI before SPICLK low (clock polarity = 0)

0 0

su(SOMI-SPCH)M

Setup time, SPISOMI before SPICLK high (clock polarity = 1)

0 0

v(SPCL-SOMI)M

Valid time, SPISOMI data valid after SPICLK low (clock polarity = 0)

0.25t

c(SPC)M

–10 0.5t

c(SPC)M

–0.5t

c(CO)

–10

v(SPCH-SOMI)M

Valid time, SPISOMI data valid after SPICLK high (clock polarity = 1)

0.25t

c(SPC)M

–10 0.5t

c(SPC)M

–0.5t

c(CO)

–10

†

The MASTER/SLAVE bit (SPICTL.2) is set and the CLOCK PHASE bit (SPICTL.3) is cleared.

‡

tc = system clock cycle time = 1/CLKOUT = t

c(CO)

The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).

ADVANCE INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PARAMETER MEASUREMENT INFORMATION

SPISOMI

SPISIMO

SPICLK

(clock polarity = 1)

SPICLK

(clock polarity = 0)

Master In Data

Must Be Valid

Master Out Data Is Valid

SPISTE

†

The SPISTE signal must be active before the SPI communication stream starts; the SPISTE signal must remain active until the SPI communication stream is complete.

Figure 32. SPI Master Mode External Timing (Clock Phase = 0)

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443

• 75

SPI master mode external timing parameters (clock phase = 1)†‡ (see Figure 33)

NO.

SPI WHEN (SPIBRR + 1) IS EVEN

OR SPIBRR = 0 OR 2

SPI WHEN (SPIBRR + 1)

IS ODD AND SPIBRR > 3

UNIT

MIN MAX MIN MAX

UNIT

1 t

c(SPC)M

Cycle time, SPICLK 4t

c(CO)

128t

c(CO)

127t

c(CO)

w(SPCH)M

Pulse duration, SPICLK high (clock polarity = 0)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

–0.5t

c(CO)

–10 0.5t

c(SPC)M

–0.5t

c(CO)

w(SPCL)M

Pulse duration, SPICLK low (clock polarity = 1)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

–0.5t

c(CO)

–10 0.5t

c(SPC)M

–0.5t

c(CO)

w(SPCL)M

Pulse duration, SPICLK low (clock polarity = 0)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

+0.5t

c(CO)

–10 0.5t

c(SPC)M

+ 0.5t

c(CO)

w(SPCH)M

Pulse duration, SPICLK high (clock polarity = 1)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

0.5t

c(SPC)M

+0.5t

c(CO)

–10 0.5t

c(SPC)M

+ 0.5t

c(CO)

su(SIMO-SPCH)M

Setup time, SPISIMO data valid before SPICLK high (clock polarity = 0)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

–10

su(SIMO-SPCL)M

Setup time, SPISIMO data valid before SPICLK low (clock polarity = 1)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

–10

v(SPCH-SIMO)M

Valid time, SPISIMO data valid after SPICLK high (clock polarity =0)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

–10

v(SPCL-SIMO)M

Valid time, SPISIMO data valid after SPICLK low (clock polarity =1)

0.5t

c(SPC)M

–10 0.5t

c(SPC)M

–10

su(SOMI-SPCH)M

Setup time, SPISOMI before SPICLK high (clock polarity = 0)

0 0

su(SOMI-SPCL)M

Setup time, SPISOMI before SPICLK low (clock polarity = 1)

0 0

v(SPCH-SOMI)M

Valid time, SPISOMI data valid after SPICLK high (clock polarity = 0)

0.25t

c(SPC)M

–10 0.5t

c(SPC)M

–10

v(SPCL-SOMI)M

Valid time, SPISOMI data valid after SPICLK low (clock polarity = 1)

0.25t

c(SPC)M

–10 0.5t

c(SPC)M

–10

†

The MASTER/SLAVE bit (SPICTL.2) is set and the CLOCK PHASE bit (SPICTL.3) is set.

‡

tc = system clock cycle time = 1/CLKOUT = t

c(CO)

The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).

ADVANCE INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PARAMETER MEASUREMENT INFORMATION

Data V alid

SPISOMI

SPISIMO

SPICLK

(clock polarity = 1)

SPICLK

(clock polarity = 0)

Master In Data

Must Be Valid

Master Out Data Is Valid

SPISTE

†

The SPISTE signal must be active before the SPI communication stream starts; the SPISTE signal must remain active until the SPI communication stream is complete.

Figure 33. SPI Master Mode External Timing (Clock Phase = 1)

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

SPI SLAVE MODE TIMING PARAMETERS

Slave mode timing information is listed in the following tables.

SPI slave mode external timing parameters (clock phase = 0)†‡ (see Figure 34)

NO. MIN MAX UNIT

12 t

c(SPC)S

Cycle time, SPICLK 4t

c(CO)

‡

w(SPCH)S

Pulse duration, SPICLK high (clock polarity = 0) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

w(SPCL)S

Pulse duration, SPICLK low (clock polarity = 1) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

w(SPCL)S

Pulse duration, SPICLK low (clock polarity = 0) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

w(SPCH)S

Pulse duration, SPICLK high (clock polarity = 1) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

d(SPCH-SOMI)S

Delay time, SPICLK high to SPISOMI valid (clock polarity = 0)

0.375t

c(SPC)S

–10

d(SPCL-SOMI)S

Delay time, SPICLK low to SPISOMI valid (clock polarity = 1) 0.375t

c(SPC)S

–10

v(SPCL-SOMI)S

Valid time, SPISOMI data valid after SPICLK low (clock polarity =0)

0.75t

c(SPC)S

v(SPCH-SOMI)S

Valid time, SPISOMI data valid after SPICLK high (clock polarity =1)

0.75t

c(SPC)S

su(SIMO-SPCL)S

Setup time, SPISIMO before SPICLK low (clock polarity = 0) 0

su(SIMO-SPCH)S

Setup time, SPISIMO before SPICLK high (clock polarity = 1) 0

v(SPCL-SIMO)S

Valid time, SPISIMO data valid after SPICLK low (clock polarity = 0)

0.5t

c(SPC)S

v(SPCH-SIMO)S

Valid time, SPISIMO data valid after SPICLK high (clock polarity = 1)

0.5t

c(SPC)S

†

The MASTER/SLAVE bit (SPICTL.2) is cleared and the CLOCK PHASE bit (SPICTL.3) is cleared.

‡

tc = system clock cycle time = 1/CLKOUT = t

c(CO)

The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).

ADV ANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PARAMETER MEASUREMENT INFORMATION

SPISIMO

SPISOMI

SPICLK

(clock polarity = 1)

SPICLK

(clock polarity = 0)

SPISIMO Data Must Be Valid

SPISOMI Data Is Valid

SPISTE

†

The SPISTE signal must be active before the SPI communication stream starts; the SPISTE signal must remain active until the SPI communication stream is complete.

Figure 34. SPI Slave Mode External Timing (Clock Phase = 0)

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

SPI slave mode external timing parameters (clock phase = 1)†‡ (see Figure 35)

NO. MIN MAX UNIT

12 t

c(SPC)S

Cycle time, SPICLK 8t

c(CO)

w(SPCH)S

Pulse duration, SPICLK high (clock polarity = 0) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

w(SPCL)S

Pulse duration, SPICLK low (clock polarity = 1) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

w(SPCL)S

Pulse duration, SPICLK low (clock polarity = 0) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

w(SPCH)S

Pulse duration, SPICLK high (clock polarity = 1) 0.5t

c(SPC)S

–10 0.5t

c(SPC)S

su(SOMI-SPCH)S

Setup time, SPISOMI before SPICLK high (clock polarity = 0) 0.125t

c(SPC)S

su(SOMI-SPCL)S

Setup time, SPISOMI before SPICLK low (clock polarity = 1) 0.125t

c(SPC)S

v(SPCH-SOMI)S

Valid time, SPISOMI data valid after SPICLK high (clock polarity =0)

0.75t

c(SPC)S

v(SPCL-SOMI)S

Valid time, SPISOMI data valid after SPICLK low (clock polarity =1)

0.75t

c(SPC)S

su(SIMO-SPCH)S

Setup time, SPISIMO before SPICLK high (clock polarity = 0) 0

su(SIMO-SPCL)S

Setup time, SPISIMO before SPICLK low (clock polarity = 1) 0

v(SPCH-SIMO)S

Valid time, SPISIMO data valid after SPICLK high (clock polarity = 0)

0.5t

c(SPC)S

v(SPCL-SIMO)S

Valid time, SPISIMO data valid after SPICLK low (clock polarity = 1)

0.5t

c(SPC)S

†

The MASTER/SLAVE bit (SPICTL.2) is cleared and the CLOCK PHASE bit (SPICTL.3) is set.

‡

tc = system clock cycle time = 1/CLKOUT = t

c(CO)

The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).

ADV ANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

PARAMETER MEASUREMENT INFORMATION

Data V alid

SPISIMO

SPISOMI

SPICLK

(clock polarity = 1)

SPICLK

(clock polarity = 0)

SPISIMO Data

Must Be Valid

SPISOMI Data Is Valid

SPISTE

†

The SPISTE signal must be active before the SPI communication stream starts; the SPISTE signal must remain active until the SPI communication stream is complete.

Figure 35. SPI Slave Mode External Timing (Clock Phase = 1)

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external memory interface

read

timings

switching characteristics over recommended operating conditions for an external memory interface read (see Figure 36)

PARAMETER MIN MAX UNIT

d(COL–CNTL)

Delay time, CLKOUT low to control valid

3 ns

d(COL–CNTH)

Delay time, CLKOUT low to control inactive

3 ns

d(COL–A)RD

Delay time, CLKOUT low to address valid

5 ns

d(COH–RDL)

Delay time, CLKOUT high to RD strobe active

4 ns

d(COL–RDH)

Delay time, CLKOUT low to RD strobe inactive high

–4 0 ns

d(COL–SL)

Delay time, CLKOUT low to STRB strobe active low

3 ns

d(COL–SH)

Delay time, CLKOUT low to STRB strobe inactive high

3 ns

h(A)COL

Hold time, address valid after CLKOUT low

–4 ns

su(A)RD

Setup time, address valid before RD strobe active low

22 ns

h(A)RD

Hold time, address valid after RD strobe inactive high

–1 ns

timing requirements [H = 0.5t

c(CO)

] (see Figure 36)

MIN MAX UNIT

a(A)

Access time, read data from address valid

2H–13 ns

su(D)RD

Setup time, read data before RD strobe inactive high

12 ns

h(D)RD

Hold time, read data after RD strobe inactive high

0 ns

h(AIV-D)

Hold time, read data after address invalid

–3 ns

ADV ANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external memory interface

read

timings (continued)

d(COL–CNTH)

h(A)COL

d(COL–A)RD

h(A)COL

d(COL–RDH)

d(COH–RDL)

a(A)

d(COH–RDL)

CLKOUT

PS, DS, IS, BR

A[0:15]

d(COL–CNTL)

d(COL–A)RD

h(A)RD

su(D)RD

h(D)RD

su(A)RD

h(D)RD

su(D)RD

d(COL–SH)

D[0:15]

STRB

d(COL–SL)

d(COL–RDH)

a(A)

h(AIV–D)

Figure 36. Memory Interface Read/Read Timings

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external memory interface

write

timings

switching characteristics over recommended operating conditions for an external memory interface write [H = 0.5t

c(CO)

] (see Figure 37)

PARAMETER MIN MAX UNIT

d(COH–CNTL)

Delay time, CLKOUT high to control valid

9 ns

d(COH–CNTH)

Delay time, CLKOUT high to control inactive

9 ns

d(COH–A)W

Delay time, CLKOUT high to address valid

11 ns

d(COH–RWL)

Delay time, CLKOUT high to R/W low

6 ns

d(COH–RWH)

Delay time, CLKOUT high to R/W high

6 ns

d(COL–WL)

Delay time, CLKOUT low to WE strobe active low

–4 0 ns

d(COL–WH)

Delay time, CLKOUT low to WE strobe inactive high

–4 0 ns

en(D)COL

Enable time, data bus driven from CLKOUT low

7 ns

d(COL–SL)

Delay time, CLKOUT low to STRB active low

3 ns

d(COL–SH)

Delay time, CLKOUT low to STRB inactive high

3 ns

h(A)COHW

Hold time, address valid after CLKOUT high

H–1 ns

su(A)W

Setup time, address valid before WE strobe active low

H–9 ns

su(D)W

Setup time, write data before WE strobe inactive high

2H–1 ns

h(D)W

Hold time, write data after WE strobe inactive high

3 ns

dis(W-D)

Disable time, data bus high impedance from WE high

4 ns

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external memory interface

write

timings (continued)

dis(W-D)

d(COH–A)W

d(COH–RWL)

su(A)W

d(COL–WH)

STRB

en(D)COL

d(COL–WL)

h(A)COHW

d(COH–CNTL)

d(COH–CNTH)

CLKOUT

A[0:15]

R/W

PS, DS, IS, BR

d(COH–CNTL)

d(COH–RWH)

d(COL–WL)

d(COL–WH)

h(D)W

su(D)W

en(D)COL

d(COL–SH)

CLKOUT

ENA_144

VIS_OE

h(D)W

2H 2H

d(COL–SL)

NOTE A: ENA_144 when active low along with BVIS bits (10,9 set to 01 or 1 1) in register WSGR - IO@FFFFh, CLKOUT and VIS_OE will be visible

at pins xx (’LF240x) and xx (’LF240x), respectively. CLKOUT and VIS_OE indicate internal memory write cycles (program/data). During VIS_OE cycles, the external bus will be driven. CLKOUT is to be used along with VIS_OE for trace capabilities.

su(D)W

d(COL–SL)

D[0:15]

d(COL–SH)

Figure 37. Address Visibility Mode

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external memory interface

ready-on-read

timings

switching characteristics over recommended operating conditions for an external memory interface ready-on-read (see Figure 38)

PARAMETER MIN MAX UNIT

d(COL–A)RD

Delay time, CLKOUT low to address valid

5 ns

timing requirements for an external memory interface ready-on-read (see Figure 38)

MIN MAX UNIT

h(RDY)COH

Hold time, READY after CLKOUT high

–5 ns

su(D)RD

Setup time, read data before RD strobe inactive high

12 ns

v(RDY)ARD

Valid time, READY after address valid on read

4 ns

su(RDY)COH

Setup time, READY before CLKOUT high

17 ns

h(RDY)COH

CLKOUT

PS, DS, IS, BR

D[0:15]

STRB

A[0:15]

d(COL–A)RD

v(RDY)ARD

su(RDY)COH

READY

Wait Cycle

su(D)RD

Figure 38. Ready-on-Read Timings

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

external memory interface

ready-on-write

timings

switching characteristics over recommended operating conditions for an external memory interface ready-on-write (see Figure 39)

PARAMETER MIN MAX UNIT

d(COH–A)W

Delay time, CLKOUT high to address valid

11 ns

timing requirements for an external memory interface ready-on-write [H = 0.5t

c(CO)

]

(see Figure 39)

MIN MAX UNIT

h(RDY)COH

Hold time, READY after CLKOUT high

–5 ns

su(D)W

Setup time, write data before WE strobe inactive high

2H–1 2H ns

v(RDY)AW

Valid time, READY after address valid on write

4 ns

su(RDY)COH

Setup time, READY before CLKOUT high

17 ns

su(D)W

CLKOUT

PS, DS, IS, BR

d(COH–A)W

A[0:15]

D[0:15]

STRB

su(RDY)COH

h(RDY)COH

READY

v(RDY)AW

Wait Cycle

Figure 39. Ready-on-Write Timings

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

10-bit analog-to-digital converter (ADC)

The 10-bit ADC has a separate power bus for its analog circuitry. These pins are referred to as V

CCA

and V

SSA

. The power bus isolation is to enhance ADC performance by preventing digital switching noise of the logic circuitry that can be present on VSS and VCC from coupling into the ADC analog stage. All ADC specifications are given with respect to V

SSA

unless otherwise noted.

Resolution 10-bit (1024 values). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Monotonic Assured. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output conversion mode 000h to 3FFh (000h for VI ≤ V

SSA

; 3FFh for VI ≥ V

CCA

). . . . . . . . . . . . . . . . . . . . . . .

Conversion time (including sample time) 500 ns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

recommended operating conditions

MIN NOM MAX UNIT

CCA

Analog supply voltage 3.0 3.3 3.6 V

SSA

Analog ground 0 V

REFHI

Analog supply reference source

†

REFLO

CCA

REFLO

Analog ground reference source

†

SSA

REFHI

Analog input voltage, ADCIN00–ADCIN07 V

SSA

CCA

†

REFHI

and V

REFLO

must be stable, within ±1/2 LSB of the required resolution, during the entire conversion time.

ADC operating frequency

MIN MAX UNIT

ADC operating frequency 30 MHz

ADV ANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

operating characteristics over recommended operating condition ranges

†

PARAMETER DESCRIPTION MIN MAX UNIT

Converting 10

CCA

= 3.3 V

Non-converting 2

CCA

Anal

og supply current

CCA

= V

REFHI

= 3.3 V

PLL or OSC power down

1 mA

Typical capacitive load on

Non-sampling 10

Analog input capacitance

Ty ical ca acitive load on

analog input pin

Sampling 30

DNL

Differential nonlinearity error

Difference between the actual step width and the ideal value

"2 LSB

INL

Integral nonlinearity error

Maximum deviation from the best straight line through the ADC transfer characteristics, excluding the quantization error

"2 LSB

d(PU)

Delay time, power-up to ADC valid Time to stabilize analog stage after power-up 10 ms

Analog input source impedance

Analog input source impedance for conversions to remain within specifications at min t

w(SH)

10 Ω

†

Absolute resolution = 4.89 mV . At V

REFHI

= 3.3 V and V

REFLO

= 0 V, this is one LSB. As V

REFHI

decreases, V

REFLO

increases, or both, the LSB

size decreases. Therefore, the absolute accuracy and differential/integral linearity errors in terms of LSBs increase.

ADV ANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCT OBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

internal ADC module timings (see Figure 40)

MIN MAX UNIT

c(AD)

Cycle time, ADC prescaled clock 33.3 ns

w(SHC)

Pulse duration, total sample/hold and conversion time

†

500 ns

w(SH)

Pulse duration, sample and hold time 2t

c(AD)

‡

32t

c(AD)

w(C)

Pulse duration, total conversion time 10t

c(AD)

d(SOC-SH)

Delay time, start of conversion to beginning of sample and hold 3t

c(CO)

d(EOC-FIFO)

Delay time, end of conversion to data loaded into result register 2t

c(CO)

d(ADCINT)

Delay time, ADC flag to ADC interrupt 2t

c(CO)

†

The total sample/hold and conversion time is determined by the summation of t

d(SOC-SH)

, t

w(SH

), t

w(C)

, and t

d(EOC-FIFO)

‡

Can be varied by ACQ Prescalar bits in the ADCCTRL1 register

451

w(C)

678

c(AD)

ADC Clock

Analog Input

Bit Converted

d(SOC–SH)

EOC/Convert

Internal Start/ Sample Hold

Start of Convert

XFR to FIFO

w(SHC)

d(EOC–FIFO)

w(SH)

d(ADCINT)

Figure 40. Analog-to-Digital Internal Module Timing

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description

Table 18 is a collection of all the programmable registers of the ’LF240x/’LC240x and is provided as a quick reference.

T able 18. ’LF240x/’LC240x DSP Peripheral Register Description

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

DATA MEMORY SPACE

CPU STATUS REGISTERS

ARP OV OVM 1 INTM DP(8)

DP(7) DP(6) DP(5) DP(4) DP(3) DP(2) DP(1) DP(0)

ST0

ARB CNF TC SXM C 1

1 1 1 XF 1 1 PM

ST1

GLOBAL MEMORY AND CPU INTERRUPT REGISTERS

— — — — — — — —

00004h

—

— INT6 MASK INT5 MASK INT4 MASK INT3 MASK INT2 MASK INT1 MASK

IMR

00005h Reserved GREG

— — — — — — — —

00006h

—

— INT6 FLAG INT5 FLAG INT4 FLAG INT3 FLAG INT2 FLAG INT1 FLAG

IFR

SYSTEM REGISTERS

IRQ0.15 IRQ0.14 IRQ0.13 IRQ0.12 IRQ0.11 IRQ0.10 IRQ0.9 IRQ0.8

07010h

IRQ0.7

IRQ0.6 IRQ0.5 IRQ0.4 IRQ0.3 IRQ0.2 IRQ0.1 IRQ0.0

PIRQR0

IRQ1.15 IRQ1.14 IRQ1.13 IRQ1.12 IRQ1.11 IRQ1.10 IRQ1.9 IRQ1.8

07011h

IRQ1.7

IRQ1.6 IRQ1.5 IRQ1.4 IRQ1.3 IRQ1.2 IRQ1.1 IRQ1.0

PIRQR1

07012h Reserved PIRQR2 07013h Reserved

IAK0.15 IAK0.14 IAK0.13 IAK0.12 IAK0.11 IAK0.10 IAK0.9 IAK0.8

07014h

IAK0.7

IAK0.6 IAK0.5 IAK0.4 IAK0.3 IAK0.2 IAK0.1 IAK0.0

PIACKR0

IAK1.15 IAK1.14 IAK1.13 IAK1.12 IAK1.11 IAK1.10 IAK1.9 IAK1.8

07015h

IAK1.7

IAK1.6 IAK1.5 IAK1.4 IAK1.3 IAK1.2 IAK1.1 IAK1.0

PIACKR1

07016h Reserved PIACKR2 07017h Reserved

OSC FAIL

FLAG

CLKSRC LPM1 LPM0 CLK PS2 CLK PS1 CLK PS0

OSC FAIL

RESET

07018h

ADC CLKEN SCI CLKEN SPI CLKEN CAN CLKEN EVB CLKEN EVA CLKEN

NMI EN

(test only)

ILLADR

SCSR1

— — — — — — — —

07019h

— —

OVERRIDE

XMIF HI Z BOOT_EN MP/MC DON PON

SCSR2

0701Ah

0701Bh

Reserved

DIN15 DIN14 DIN13 DIN12 DIN11 DIN10 DIN9 DIN8

0701Ch

DIN7

DIN6 DIN5 DIN4 DIN3 DIN2 DIN1 DIN0

DINR

0701Dh Reserved

V15 V14 V13 V12 V11 V10 V9 V8

0701Eh

V6 V5 V4 V3 V2 V1 V0

PIVR

0701Fh Reserved

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

WD CONTROL REGISTERS

07020h

07022h

Reserved

07023h D7 D6 D5 D4 D3 D2 D1 D0 WDCNTR 07024h Reserved 07025h D7 D6 D5 D4 D3 D2 D1 D0 WDKEY 07026h

07028h

Reserved

07029h WD FLAG WDDIS WDCHK2 WDCHK1 WDCHK0 WDPS2 WDPS1 WDPS0 WDCR

0702Ah

07031h

Reserved

07032h

07038h

Reserved

07039h

0703Fh

Reserved

SERIAL PERIPHERAL INTERFACE (SPI) CONFIGURA TION CONTROL REGISTERS

07040h

SPI SW RESET

CLOCK

POLARITY

— —

SPI

CHAR3

SPI

CHAR2

SPI

CHAR1

SPI

CHAR0

SPICCR

07041h — — —

OVERRUN

INT ENA

CLOCK

PHASE

MASTER/

SLAVE

TALK

SPI INT

ENA

SPICTL

07042h

RECEIVER OVERRUN

FLAG

SPI INT

FLAG

TX BUF

FULL FLAG

— — — — — SPISTS

07043h Reserved

07044h —

SPI BIT RATE 6

SPI BIT RATE 5

SPI BIT RATE 4

SPI BIT RATE 3

SPI BIT RATE 2

SPI BIT RATE 1

SPI BIT RATE 0

SPIBRR

07045h Reserved

ERXB15 ERXB14 ERXB13 ERXB12 ERXB11 ERXB10 ERXB9 ERXB8

07046h

ERXB7

ERXB6 ERXB5 ERXB4 ERXB3 ERXB2 ERXB1 ERXB0

SPIRXEMU

RXB15 RXB14 RXB13 RXB12 RXB11 RXB10 RXB9 RXB8

07047h

RXB7

RXB6 RXB5 RXB4 RXB3 RXB2 RXB1 RXB0

SPIRXBUF

TXB15 TXB14 TXB13 TXB12 TXB11 TXB10 TXB9 TXB8

07048h

TXB7

TXB6 TXB5 TXB4 TXB3 TXB2 TXB1 TXB0

SPITXBUF

SDAT15 SDAT14 SDAT13 SDAT12 SDAT1 1 SDAT10 SDAT9 SDAT8

07049h

SDAT7

SDAT6 SDAT5 SDAT4 SDAT3 SDAT2 SDAT1 SDAT0

SPIDAT

0704Ah

Reserved

0704Eh

Reserved

0704Fh —

SPI

PRIORITY

SPI

SUSP SOFT

SPI

SUSP FREE

— — — — SPIPRI

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

SERIAL COMMUNICATIONS INTERFACE (SCI) CONFIGURATION CONTROL REGISTERS

07050h

STOP

BITS

EVEN/ODD

PARITY

ENABLE

LOOP BACK

ENA

ADDR/IDLE

MODE

SCI

CHAR2

SCI

CHAR1

SCI

CHAR0

SCICCR

07051h —

RX ERR

INT ENA

SW RESET — TXWAKE SLEEP TXENA RXENA SCICTL1

07052h

BAUD15

(MSB)

BAUD14 BAUD13 BAUD12 BAUD11 BAUD10 BAUD9 BAUD8 SCIHBAUD

07053h BAUD7 BAUD6 BAUD5 BAUD4 BAUD3 BAUD2 BAUD1

BAUD0

(LSB)

SCILBAUD

07054h TXRDY TX EMPTY — — — —

RX/BK

INT ENA

SCICTL2

07055h RX ERROR RXRDY BRKDT FE OE PE RXWAKE — SCIRXST 07056h ERXDT7 ERXDT6 ERXDT5 ERXDT4 ERXDT3 ERXDT2 ERXDT1 ERXDT0 SCIRXEMU 07057h RXDT7 RXDT6 RXDT5 RXDT4 RXDT3 RXDT2 RXDT1 RXDT0 SCIRXBUF 07058h Reserved 07059h TXDT7 TXDT6 TXDT5 TXDT4 TXDT3 TXDT2 TXDT1 TXDT0 SCITXBUF 0705Ah

0705Eh

Reserved

0705Fh —

SCITX

PRIORITY

SCIRX

PRIORITY

SCI

SOFT

SCI

FREE

— — — SCIPRI

07060h

0706Fh

Reserved

EXTERNAL INTERRUPT CONTROL REGISTERS

XINT1

FLAG

— — — — — — —

07070h

—

— — — —

XINT1

POLARITY

XINT1

PRIORITY

XINT1

ENA

XINT1CR

XINT2

FLAG

— — — — — — —

07071h

—

— — — —

XINT2

POLARITY

XINT2

PRIORITY

XINT2

ENA

XINT2CR

07072h

0708Fh

Reserved

DIGITAL I/O CONTROL REGISTERS

MCRA.15 MCRA.14 MCRA.13 MCRA.12 MCRA.11 MCRA.10 MCRA.9 MCRA.8

07090h

MCRA.7

MCRA.6 MCRA.5 MCRA.4 MCRA.3 MCRA.2 MCRA.1 MCRA.0

MCRA

07091h Reserved

MCRB.15 MCRB.14 MCRB.13 MCRB.12 MCRB.11 MCRB.10 MCRB.9 MCRB.8

07092h

MCRB.7

MCRB.6 MCRB.5 MCRB.4 MCRB.3 MCRB.2 MCRB.1 MCRB.0

MCRB

07093h Reserved

MCRC.15 MCRC.14 MCRC.13 MCRC.12 MCRC.11 MCRC.10 MCRC.9 MCRC.8

07094h

MCRC.7

MCRC.6 MCRC.5 MCRC.4 MCRC.3 MCRC.2 MCRC.1 MCRC.0

MCRC

E7DIR E6DIR E5DIR E4DIR E3DIR E2DIR E1DIR E0DIR

07095h

IOPE7 IOPE6 IOPE5 IOPE4 IOPE3 IOPE2 IOPE1 IOPE0

PEDATDIR

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

DIGITAL I/O CONTROL REGISTERS (CONTINUED)

F7DIR F6DIR F5DIR F4DIR F3DIR F2DIR F1DIR F0DIR

07096h

IOPF7 IOPF6 IOPF5 IOPF4 IOPF3 IOPF2 IOPF1 IOPF0

PFDATDIR

A7DIR A6DIR A5DIR A4DIR A3DIR A2DIR A1DIR A0DIR

07098h

IOPA7

IOPA6 IOP A5 IOP A4 IOPA3 IOPA2 IOPA1 IOPA0

PADATDIR

07099h Reserved

B7DIR B6DIR B5DIR B4DIR B3DIR B2DIR B1DIR B0DIR

0709Ah

IOPB7

IOPB6 IOPB5 IOPB4 IOPB3 IOPB2 IOPB1 IOPB0

PBDATDIR

0709Bh Reserved

C7DIR C6DIR C5DIR C4DIR C3DIR C2DIR C1DIR C0DIR

0709Ch

IOPC7

IOPC6 IOPC5 IOPC4 IOPC3 IOPC2 IOPC1 IOPC0

PCDATDIR

0709Dh Reserved

D7DIR D6DIR D5DIR D4DIR D3DIR D2DIR D1DIR D0DIR

0709Eh

IOPD7

IOPD6 IOPD5 IOPD4 IOPD3 IOPD2 IOPD1 IOPD0

PDDATDIR

0709Fh Reserved

ANALOG-TO-DIGIT AL CONVERTER (ADC) REGISTERS

—

ADC

S/W RESET

SOFT FREE

ACQ

PRESCALE3

ACQ

PRESCALE2

ACQ

PRESCALE1

ACQ

PRESCALE0

070A0h

CONV PRE-

SCALE (CPS)

CONTIN-

UOUS RUN

INT

PRIORITY

SEQ1/2

CASCADE

CALIB EN BRIDGE EN HI / LO FSTEST EN

ADCCTRL1

EVB SOC

EN SEQ1

Reset SEQ1

Start CALIB

SOC SEQ1 SEQ1 BUSY

INT ENA

SEQ1 Mode1

INT ENA

SEQ1 Mode0

INT FLAG

SEQ1

EVA SOC EN SEQ1

070A1h

EXT SOC EN SEQ1

Reset SEQ2 SOC SEQ2 SEQ2 BUSY

INT ENA

SEQ2 Mode1

INT ENA

SEQ2 Mode0

INT FLAG

SEQ2

EVB SOC EN SEQ2

ADCCTRL2

— — — — — — — —

070A2h

—

MAXCONV22MAXCONV21MAXCONV20MAXCONV13MAXCONV12MAXCONV11MAXCONV1

MAXCONV

CONV 3 CONV 3 CONV 3 CONV 3 CONV 2 CONV 2 CONV 2 CONV 2

070A3h

CONV 1 CONV 1 CONV 1 CONV 1 CONV 0 CONV 0 CONV 0 CONV 0

CHSELSEQ1

CONV 7 CONV 7 CONV 7 CONV 7 CONV 6 CONV 6 CONV 6 CONV 6

070A4h

CONV 5 CONV 5 CONV 5 CONV 5 CONV 4 CONV 4 CONV 4 CONV 4

CHSELSEQ2

CONV 11 CONV 11 CONV 1 1 CONV 11 CONV 10 CONV 10 CONV 10 CONV 10

070A5h

CONV 9 CONV 9 CONV 9 CONV 9 CONV 8 CONV 8 CONV 8 CONV 8

CHSELSEQ3

CONV 15 CONV 15 CONV 15 CONV 15 CONV 14 CONV 14 CONV 14 CONV 14

070A6h

CONV 13 CONV 13 CONV 13 CONV 13 CONV 12 CONV 12 CONV 12 CONV 12

CHSELSEQ4

— — — — SEQ CNTR3 SEQ CNTR2 SEQ CNTR1 SEQ CNTR0

070A7h

SEQ2-STATE

SEQ2

STATE

SEQ2

STATE

SEQ2

STATE

SEQ1-STATE3SEQ1-STATE

SEQ1

STATE

SEQ1-STATE

AUTO_SEQ_SR

D9 D8 D7 D6 D5 D4 D3 D2

070A8h

D1 D0 0 0 0 0 0 0

RESULT0

D9 D8 D7 D6 D5 D4 D3 D2

070A9h

D1 D0 0 0 0 0 0 0

RESULT1

D9 D8 D7 D6 D5 D4 D3 D2

070AAh

D1 D0 0 0 0 0 0 0

RESULT2

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

ANALOG-TO-DIGIT AL CONVERTER (ADC) REGISTERS (CONTINUED)

D9 D8 D7 D6 D5 D4 D3 D2

070ABh

D1 D0 0 0 0 0 0 0

RESULT3

D9 D8 D7 D6 D5 D4 D3 D2

070ACh

D1 D0 0 0 0 0 0 0

RESULT4

D9 D8 D7 D6 D5 D4 D3 D2

070ADh

D1 D0 0 0 0 0 0 0

RESULT5

D9 D8 D7 D6 D5 D4 D3 D2

070AEh

D1 D0 0 0 0 0 00 0

RESULT6

D9 D8 D7 D6 D5 D4 D3 D2

070AFh

D1 D0 0 0 0 0 0 0

RESULT7

D9 D8 D7 D6 D5 D4 D3 D2

070B0h

D1 D0 0 0 0 0 0 0

RESULT8

D9 D8 D7 D6 D5 D4 D3 D2

070B1h

D1 D0 0 0 0 0 0 0

RESULT9

D9 D8 D7 D6 D5 D4 D3 D2

070B2h

D1 D0 0 0 0 0 0 0

RESULT10

D9 D8 D7 D6 D5 D4 D3 D2

070B3h

D1 D0 0 0 0 0 0 0

RESULT11

D9 D8 D7 D6 D5 D4 D3 D2

070B4h

D1 D0 0 0 0 0 0 0

RESULT12

D9 D8 D7 D6 D5 D4 D3 D2

070B5h

D1 D0 0 0 0 0 0 0

RESULT13

D9 D8 D7 D6 D5 D4 D3 D2

070B6h

D1 D0 0 0 0 0 0 0

RESULT14

D9 D8 D7 D6 D5 D4 D3 D2

070B7h

D1 D0 0 0 0 0 0 0

RESULT15

070B8h CALIBRATION

070B9h

070FFh

Reserved

CONTROLLER AREA NETWORK (CAN) CONFIGURATION CONTROL REGISTERS

— — — — — — — —

07100h

MD3

MD2 ME5 ME4 ME3 ME2 ME1 ME0

MDER

TA5 TA4 TA3 TA2 AA5 AA4 AA3 AA2

07101h

TRS5

TRS4 TRS3 TRS2 TRR5 TRR4 TRR3 TRR2

TCR

RFP3 RFP2 RFP1 RFP0 RML3 RML2 RML1 RML0

07102h

RMP3

RMP2 RMP1 RMP0 OPC3 OPC2 OPC1 OPC0

RCR

— — SUSP CCR PDR DBO WUBA CDR

07103h

ABO

STM — — — — MBNR1 MBNR0

MCR

— — — — — — — —

07104h

BRP7

BRP6 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0

BCR2

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

CONTROLLER AREA NETWORK (CAN) CONFIGURATION CONTROL REGISTERS (CONTINUED)

— — — — — SBG SJW1 SJW0

07105h

SAM

TSEG1–3 TSEG1–2 TSEG1–1 TSEG1–0 TSEG2–2 TSEG2–1 TSEG2–0

BCR1

— — — — — — — FER

07106h

BEF

SA1 CRCE SER ACKE BO EP EW

ESR

— — — — — — — —

07107h

—

— SMA CCE PDA — RM TM

GSR

TEC7 TEC6 TEC5 TEC4 TEC3 TEC2 TEC1 TEC0

07108h

REC7

REC6 REC5 REC4 REC3 REC2 REC1 REC0

CEC

— — MIF5 MIF4 MIF3 MIF2 MIF1 MIF0

07109h

—

RMLIF AAIF WDIF WUIF BOIF EPIF WLIF

CAN_IFR

MIL — MIM5 MIM4 MIM3 MIM2 MIM1 MIM0

0710Ah

EIL

RMLIM AAIM WDIM WUIM BOIM EPIM WLIM

CAN_IMR

LAMI — — LAM0–28 LAM0–27 LAM0–26 LAM0–25 LAM0–24

0710Bh

LAM0–23

LAM0–22 LAM0–21 LAM0–20 LAM0–19 LAM0–18 LAM0–17 LAM0–16

LAM0_H

LAM0–15 LAM0–14 LAM0–13 LAM0–12 LAM0–11 LAM0–10 LAM0–9 LAM0–8

0710Ch

LAM0–7

LAM0–6 LAM0–5 LAM0–4 LAM0–3 LAM0–2 LAM0–1 LAM0–0

LAM0_L

LAMI — — LAM1–28 LAM1–27 LAM1–26 LAM1–25 LAM1–24

0710Dh

LAM1–23

LAM1–22 LAM1–21 LAM1–20 LAM1–19 LAM1–18 LAM1–17 LAM1–16

LAM1_H

LAM1–15 LAM1–14 LAM1–13 LAM1–12 LAM1–11 LAM1–10 LAM1–9 LAM1–8

0710Eh

LAM1–7

LAM1–6 LAM1–5 LAM1–4 LAM1–3 LAM1–2 LAM1–1 LAM1–0

LAM1_L

0710Fh

071FFh

Reserved

Message Object #0

IDL–15 IDL–14 IDL–13 IDL–12 IDL–11 IDL–10 IDL–9 IDL–8

07200h

IDL–7

IDL–6 IDL–5 IDL–4 IDL–3 IDL–2 IDL–1 IDL–0

MSGID0L

IDE AME AAM IDH–28 IDH–27 IDH–26 IDH–25 IDH–24

07201h

IDH–23

IDH–22 IDH–21 IDH–20 IDH–19 IDH–18 IDH–17 IDH–16

MSGID0H

— — — — — — — —

07202h

—

— — RTR DLC3 DLC2 DLC1 DLC0

MSGCTRL0

07203h Reserved

D15 D14 D13 D12 D11 D10 D9 D8

07204h

D6 D5 D4 D3 D2 D1 D0

MBX0A

D15 D14 D13 D12 D11 D10 D9 D8

07205h

D6 D5 D4 D3 D2 D1 D0

MBX0B

D15 D14 D13 D12 D11 D10 D9 D8

07206h

D6 D5 D4 D3 D2 D1 D0

MBX0C

D15 D14 D13 D12 D11 D10 D9 D8

07207h

D6 D5 D4 D3 D2 D1 D0

MBX0D

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

CONTROLLER AREA NETWORK (CAN) CONFIGURATION CONTROL REGISTERS (CONTINUED)

Message Object #1

IDL–15 IDL–14 IDL–13 IDL–12 IDL–11 IDL–10 IDL–9 IDL–8

07208h

IDL–7

IDL–6 IDL–5 IDL–4 IDL–3 IDL–2 IDL–1 IDL–0

MSGID1L

IDE AME AAM IDH–28 IDH–27 IDH–26 IDH–25 IDH–24

07209h

IDH–23

IDH–22 IDH–21 IDH–20 IDH–19 IDH–18 IDH–17 IDH–16

MSGID1H

— — — — — — — —

0720Ah

—

— — RTR DLC3 DLC2 DLC1 DLC0

MSGCTRL1

0720Bh Reserved

D15 D14 D13 D12 D11 D10 D9 D8

0720Ch

D6 D5 D4 D3 D2 D1 D0

MBX1A

D15 D14 D13 D12 D11 D10 D9 D8

0720Dh

D6 D5 D4 D3 D2 D1 D0

MBX1B

D15 D14 D13 D12 D11 D10 D9 D8

0720Eh

D6 D5 D4 D3 D2 D1 D0

MBX1C

D15 D14 D13 D12 D11 D10 D9 D8

0720Fh

D6 D5 D4 D3 D2 D1 D0

MBX1D

Message Object #2

IDL–15 IDL–14 IDL–13 IDL–12 IDL–11 IDL–10 IDL–9 IDL–8

07210h

IDL–7

IDL–6 IDL–5 IDL–4 IDL–3 IDL–2 IDL–1 IDL–0

MSGID2L

IDE AME AAM IDH–28 IDH–27 IDH–26 IDH–25 IDH–24

07211h

IDH–23

IDH–22 IDH–21 IDH–20 IDH–19 IDH–18 IDH–17 IDH–16

MSGID2H

— — — — — — — —

07212h

—

— — RTR DLC3 DLC2 DLC1 DLC0

MSGCTRL2

07213h Reserved

D15 D14 D13 D12 D11 D10 D9 D8

07214h

D6 D5 D4 D3 D2 D1 D0

MBX2A

D15 D14 D13 D12 D11 D10 D9 D8

07215h

D6 D5 D4 D3 D2 D1 D0

MBX2B

D15 D14 D13 D12 D11 D10 D9 D8

07216h

D6 D5 D4 D3 D2 D1 D0

MBX2C

D15 D14 D13 D12 D11 D10 D9 D8

07217h

D6 D5 D4 D3 D2 D1 D0

MBX2D

Message Object #3

IDL–15 IDL–14 IDL–13 IDL–12 IDL–11 IDL–10 IDL–9 IDL–8

07218h

IDL–7

IDL–6 IDL–5 IDL–4 IDL–3 IDL–2 IDL–1 IDL–0

MSGID3L

IDE AME AAM IDH–28 IDH–27 IDH–26 IDH–25 IDH–24

07219h

IDH–23

IDH–22 IDH–21 IDH–20 IDH–19 IDH–18 IDH–17 IDH–16

MSGID3H

— — — — — — — —

0721Ah

—

— — RTR DLC3 DLC2 DLC1 DLC0

MSGCTRL3

0721Bh Reserved

D15 D14 D13 D12 D11 D10 D9 D8

0721Ch

D6 D5 D4 D3 D2 D1 D0

MBX3A

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

CONTROLLER AREA NETWORK (CAN) CONFIGURATION CONTROL REGISTERS (CONTINUED)

D15 D14 D13 D12 D11 D10 D9 D8

0721Dh

D6 D5 D4 D3 D2 D1 D0

MBX3B

D15 D14 D13 D12 D11 D10 D9 D8

0721Eh

D6 D5 D4 D3 D2 D1 D0

MBX3C

D15 D14 D13 D12 D11 D10 D9 D8

0721Fh

D6 D5 D4 D3 D2 D1 D0

MBX3D

Message Object #4

IDL–15 IDL–14 IDL–13 IDL–12 IDL–1 1 IDL–10 IDL–9 IDL–8

07220h

IDL–7

IDL–6 IDL–5 IDL–4 IDL–3 IDL–2 IDL–1 IDL–0

MSGID4L

IDE AME AAM IDH–28 IDH–27 IDH–26 IDH–25 IDH–24

07221h

IDH–23

IDH–22 IDH–21 IDH–20 IDH–19 IDH–18 IDH–17 IDH–16

MSGID4H

— — — — — — — —

07222h

—

— — RTR DLC3 DLC2 DLC1 DLC0

MSGCTRL4

07223h Reserved

D15 D14 D13 D12 D11 D10 D9 D8

07224h

D6 D5 D4 D3 D2 D1 D0

MBX4A

D15 D14 D13 D12 D11 D10 D9 D8

07225h

D6 D5 D4 D3 D2 D1 D0

MBX4B

D15 D14 D13 D12 D11 D10 D9 D8

07226h

D6 D5 D4 D3 D2 D1 D0

MBX4C

D15 D14 D13 D12 D11 D10 D9 D8

07227h

D6 D5 D4 D3 D2 D1 D0

MBX4D

Message Object #5

IDL–15 IDL–14 IDL–13 IDL–12 IDL–1 1 IDL–10 IDL–9 IDL–8

07228h

IDL–7

IDL–6 IDL–5 IDL–4 IDL–3 IDL–2 IDL–1 IDL–0

MSGID5L

IDE AME AAM IDH–28 IDH–27 IDH–26 IDH–25 IDH–24

07229h

IDH–23

IDH–22 IDH–21 IDH–20 IDH–19 IDH–18 IDH–17 IDH–16

MSGID5H

— — — — — — — —

0722Ah

—

— — RTR DLC3 DLC2 DLC1 DLC0

MSGCTRL5

0722Bh Reserved

D15 D14 D13 D12 D11 D10 D9 D8

0722Ch

D6 D5 D4 D3 D2 D1 D0

MBX5A

D15 D14 D13 D12 D11 D10 D9 D8

0722Dh

D6 D5 D4 D3 D2 D1 D0

MBX5B

D15 D14 D13 D12 D11 D10 D9 D8

0722Eh

D6 D5 D4 D3 D2 D1 D0

MBX5C

D15 D14 D13 D12 D11 D10 D9 D8

0722Fh

D6 D5 D4 D3 D2 D1 D0

MBX5D

07230h

073FFh

Reserved

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

GENERAL-PURPOSE (GP) TIMER CONFIGURA TION CONTROL REGISTERS – EVA

— T2STAT T1STAT — T2TOADC T1TOADC(1)

07400h

T1TOADC(0)

TCOMPOE — T2PIN T1PIN

GPTCONA

D15 D14 D13 D12 D11 D10 D9 D8

07401h

D6 D5 D4 D3 D2 D1 D0

T1CNT

D15 D14 D13 D12 D11 D10 D9 D8

07402h

D6 D5 D4 D3 D2 D1 D0

T1CMPR

D15 D14 D13 D12 D11 D10 D9 D8

07403h

D6 D5 D4 D3 D2 D1 D0

T1PR

FREE SOFT — TMODE1 TMODE0 TPS2 TPS1 TPS0

07404h

TSWT1

TENABLE TCLKS1 TCLKS0 TCLD1 TCLD0 TECMPR SELT1PR

T1CON

D15 D14 D13 D12 D11 D10 D9 D8

07405h

D6 D5 D4 D3 D2 D1 D0

T2CNT

D15 D14 D13 D12 D11 D10 D9 D8

07406h

D6 D5 D4 D3 D2 D1 D0

T2CMPR

D15 D14 D13 D12 D11 D10 D9 D8

07407h

D6 D5 D4 D3 D2 D1 D0

T2PR

FREE SOFT — TMODE1 TMODE0 TPS2 TPS1 TPS0

07408h

TSWT1

TENABLE TCLKS1 TCLKS0 TCLD1 TCLD0 TECMPR SELT1PR

T2CON

07409h

07410h

Reserved

FULL AND SIMPLE COMPARE UNIT REGISTERS – EVA

CENABLE CLD1 CLD0 SVENABLE ACTRLD1 ACTRLD0 FCOMPOE —

07411h

—

— — — — — — —

COMCONA

07412h Reserved

SVRDIR D2 D1 D0 CMP6ACT1 CMP6ACT0 CMP5ACT1 CMP5ACT0

07413h

CMP4ACT1

CMP4ACT0 CMP3ACT1 CMP3ACT0 CMP2ACT1 CMP2ACT0 CMP1ACT1 CMP1ACT0

ACTRA

07414h Reserved

— — — — DBT3 DBT2 DBT1 DBT0

07415h

EDBT3

EDBT2 EDBT1 DBTPS2 DBTPS1 DBTPS0 — —

DBTCONA

07416h Reserved

D15 D14 D13 D12 D11 D10 D9 D8

07417h

D6 D5 D4 D3 D2 D1 D0

CMPR1

D15 D14 D13 D12 D11 D10 D9 D8

07418h

D6 D5 D4 D3 D2 D1 D0

CMPR2

D15 D14 D13 D12 D11 D10 D9 D8

07419h

D6 D5 D4 D3 D2 D1 D0

CMPR3

0741Ah

0741Fh

Reserved

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402

TMS320LC2406, TMS320LC2404, TMS320LC2402

DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

CAPTURE UNIT REGISTERS – EVA

CAPRES CAPQEPN CAP3EN — CAP3TSEL CAP12TSEL CAP3TOADC

07420h

CAP1EDGE

CAP2EDGE CAP3EDGE —

CAPCONA

07421h Reserved

— CAP3FIFO CAP2FIFO CAP1FIFO

07422h

—

— — — — — — —

CAPFIFOA

D15 D14 D13 D12 D11 D10 D9 D8

07423h

D6 D5 D4 D3 D2 D1 D0

CAP1FIFO

D15 D14 D13 D12 D11 D10 D9 D8

07424h

D6 D5 D4 D3 D2 D1 D0

CAP2FIFO

D15 D14 D13 D12 D11 D10 D9 D8

07425h

D6 D5 D4 D3 D2 D1 D0

CAP3FIFO

07426h Reserved

D15 D14 D13 D12 D11 D10 D9 D8

07427h

D6 D5 D4 D3 D2 D1 D0

CAP1FBOT

D15 D14 D13 D12 D11 D10 D9 D8

07428h

D6 D5 D4 D3 D2 D1 D0

CAP2FBOT

D15 D14 D13 D12 D11 D10 D9 D8

07429h

D6 D5 D4 D3 D2 D1 D0

CAP3FBOT

0742Ah

0742Bh

Reserved

EVENT MANAGER (EVA) INTERRUPT CONTROL REGISTERS

— — — — —

T1OFINT

ENA

T1UFINT

ENA

T1CINT

ENA

0742Ch

T1PINT

ENA

— — —

CMP3INT

ENA

CMP2INT

ENA

CMP1INT

ENA

PDPINT

ENA

EVAIMRA

— — — — — — — —

0742Dh

—

— — —

T2OFINT

ENA

T2UFINT

ENA

T2CINT

ENA

T2PINT

ENA

EVAIMRB

— — — — — — — —

0742Eh

—

— — — —

CAP3INT

ENA

CAP2INT

ENA

CAP1INT

ENA

EVAIMRC

— — — — —

T1OFINT

FLAG

T1UFINT

FLAG

T1CINT

FLAG

0742Fh

T1PINT

FLAG

— — —

CMP3INT

FLAG

CMP2INT

FLAG

CMP1INT

FLAG

PDPINT

FLAG

EVAIFRA

— — — — — — — —

07430h

—

— — —

T2OFINT

FLAG

T2UFINT

FLAG

T2CINT

FLAG

T2PINT

FLAG

EVAIFRB

— — — — — — — —

07431h

—

— — — —

CAP3INT

FLAG

CAP2INT

FLAG

CAP1INT

FLAG

EVAIFRC

07432h

074FFh

Reserved

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

TMS320LF2407, TMS320LF2406, TMS320LF2402 TMS320LC2406, TMS320LC2404, TMS320LC2402 DSP CONTROLLERS

SPRS094C – APRIL 1999 – REVISED OCTOBER 1999

100

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443

peripheral register description (continued)

Table 18. ’LF240x/’LC240x DSP Peripheral Register Description (Continued)

BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8

ADDR

BIT 7

BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

REG

GENERAL-PURPOSE (GP) TIMER CONFIGURA TION CONTROL REGISTERS – EVB

— T4STAT T3STAT — T4TOADC T3TOADC(1)

07500h

T3TOADC(0) TCOMPOEB — T4PIN T3PIN

GPTCONB

D15 D14 D13 D12 D11 D10 D9 D8

07501h

D7 D6 D5 D4 D3 D2 D1 D0

T3CNT

D15 D14 D13 D12 D11 D10 D9 D8

07502h

D7 D6 D5 D4 D3 D2 D1 D0

T3CMPR

D15 D14 D13 D12 D11 D10 D9 D8

07503h

D7 D6 D5 D4 D3 D2 D1 D0

T3PR

FREE SOFT — TMODE1 TMODE0 TPS2 TPS1 TPS0

07504h

TSWT3 TENABLE TCLKS3 TCLKS0 TCLD1 TCLD0 TECMPR SELT1PR

T3CON

D15 D14 D13 D12 D11 D10 D9 D8

07505h

D7 D6 D5 D4 D3 D2 D1 D0

T4CNT

D15 D14 D13 D12 D11 D10 D9 D8

07506h

D7 D6 D5 D4 D3 D2 D1 D0

T4CMPR

D15 D14 D13 D12 D11 D10 D9 D8

07507h

D7 D6 D5 D4 D3 D2 D1 D0

T4PR

FREE SOFT — TMODE1 TMODE0 TPS2 TPS1 TPS0

07508h

TSWT1 TENABLE TCLKS1 TCLKS0 TCLD1 TCLD0 TECMPR SELT3PR

T4CON

07509h

07510h

Reserved

FULL AND SIMPLE COMPARE UNIT REGISTERS– EVB

CENABLE CLD1 CLD0 SVENABLE ACTRLD1 ACTRLD0 FCOMPOEB —

07511h

— — — — — — — —

COMCONB

07512h Reserved

SVRDIR D2 D1 D0 CMP12ACT1 CMP12ACT0 CMP11ACT1 CMP11ACT0

07513h

CMP10ACT1 CMP10ACT0 CMP9ACT1 CMP9ACT0 CMP8ACT1 CMP8ACT0 CMP7ACT1 CMP7ACT0

ACTRB

07514h Reserved

— — — — DBT3 DBT2 DBT1 DBT0

07515h

EDBT3 EDBT2 EDBT1 DBTPS2 DBTPS1 DBTPS0 — —

DBTCONB

07516h Reserved

D15 D14 D13 D12 D11 D10 D9 D8

07517h

D7 D6 D5 D4 D3 D2 D1 D0

CMPR4

D15 D14 D13 D12 D11 D10 D9 D8

07518h

D7 D6 D5 D4 D3 D2 D1 D0

CMPR5

D15 D14 D13 D12 D11 D10 D9 D8

07519h

D7 D6 D5 D4 D3 D2 D1 D0

CMPR6

0751Ah

0751Fh

Reserved

’

Indicates change with respect to the ’F243/’F241, ’C242 device register maps.

ADVANCE

INFORMATION

Datasheet TMX320LF2407PGEA, TMX320LF2406PZA, TMX320LF2402PGA Datasheet (Texas Instruments)

Specifications and Main Features

Frequently Asked Questions

User Manual