Texas Instruments TLC2264IN, TLC2264IDR, TLC2264ID, TLC2264CPWR, TLC2264CPWLE Datasheet
...
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
D
Output Swing includes Both Supply Rails
D
Low Noise . . . 12 nV/√Hz Typ at f = 1 kHz
D
Low Input Bias Current ...1 pA Typ
D
Fully Specified for Both Single-Supply and
Split-Supply Operation
D
Low Power . . . 500 µA Max
D
Common-Mode Input Voltage Range
Includes Negative Rail
D
Low Input Offset Voltage
950 µV Max at TA = 25°C (TLC2262A)
D
Macromodel Included
D
Performance Upgrade for the TS27M2/M4
and TLC27M2/M4
D
Available in Q-Temp Automotive
HighRel Automotive Applications
Configuration Control / Print Support
Qualification to Automotive Standards
description
The TLC2262 and TLC2264 are dual and
quadruple operational amplifiers from Texas
Instruments. Both devices exhibit rail-to-rail
output performance for increased dynamic range
in single- or split-supply applications. The
TLC226x family offers a compromise between the
micropower TLC225x and the ac performance of
the TLC227x. It has low supply current for
battery-powered applications, while still having
adequate ac performance for applications that
demand it. The noise performance has been
dramatically improved over previous generations
of CMOS amplifiers. Figure 1 depicts the low level
of noise voltage for this CMOS amplifier, which
has only 200 µA (typ) of supply current per
amplifier.
The TLC226x, exhibiting high input impedance
and low noise, are excellent for small-signal
conditioning for high-impedance sources, such as
piezoelectric transducers. Because of the micropower dissipation levels, these devices work well
in hand-held monitoring and remote-sensing
applications. In addition, the rail-to-rail output feature with single or split supplies makes this family a great
choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the TLC226xA
family is available and has a maximum input offset voltage of 950 µV. This family is fully characterized at 5 V
and ±5 V.
The TLC2262/4 also makes great upgrades to the TLC27M2/L4 or TS27M2/L4 in standard designs. They offer
increased output dynamic range, lower noise voltage and lower input offset voltage. This enhanced feature set
allows them to be used in a wider range of applications. For applications that require higher output drive and
wider input voltage range, see the TL V2432 and TL V2442. If your design requires single amplifiers, please see
the TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23 package.
Their small size and low power consumption, make them ideal for high density, battery-powered equipment.
Copyright 1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Advanced LinCMOS is a trademark of Texas Instruments Incorporated.
40
20
10
0
60
30
VN – Equivalent Input Noise Voltage – nv//Hz
50
f – Frequency – Hz
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
10 10
2
10
3
10
4
nV/ Hz
V
n
VDD = 5 V
RS = 20 Ω
TA = 25°C
Figure 1
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262 A VAILABLE OPTIONS
PACKAGED DEVICES
T
A
VIOmax
AT 25°C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
TSSOP
(PW)
CERAMIC
FLATPACK
(U)
0°C to 70°C 2.5 mV TLC2262CD — — TLC2262CP TLC2262CPWLE —
°
°
950 µV TLC2262AID — — TLC2262AIP TLC2262AIPWLE —
–
40°C to 125°C
µ
2.5 mV TLC2262ID — — TLC2262IP — —
°
°
950 µV TLC2262AQD — — — — —
–
40°C to 125°C
µ
2.5 mV TLC2262QD — — — — —
–55°C to 125°C
950 µV
2.5 mV
—
—
TLC2262AMFK
TLC2262MFK
TLC2262AMJG
TLC2262MJG
—
—
—
—
TLC2262AMU
TLC2262MU
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2262CDR). The PW package is available only left-end taped
and reeled. Chips are tested at 25°C.
TLC2264 AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
VIOmax
AT 25°C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
PLASTIC
DIP
(N)
TSSOP
(PW)
CERAMIC
FLATPACK
(W)
0°C to 70°C 2.5 mV TLC2264CD — — TLC2264CN TLC2264CPWLE —
°
°
950 µV TLC2264AID — — TLC2264AIN TLC2264AIPWLE —
–
40°C to 125°C
µ
2.5 mV TLC2264ID — — TLC2264IN — —
°
°
950 µV TLC2264AQD — — — — —
–
40°C to 125°C
µ
2.5 mV TLC2264QD — — — — —
–55°C to 125°C
950 µV
2.5 mV
—
—
TLC2264AMFK
TLC2264MFK
TLC2264AMJ
TLC2264MJ
—
—
—
—
TLC2264AMW
TLC2264MW
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2264CDR). The PW package is available only left-end taped
and reeled. Chips are tested at 25°C.
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262M, TLC2262AM . . . JG PACKAGE
(TOP VIEW)
TLC2262C, TLC2262AC
TLC2262I, TLC2262AI
TLC2262Q, TLC2262AQ
D, P, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT
1IN–
1IN+
V
DD–
/GND
V
DD+
2OUT
2IN–
2IN+
NC
V
CC
+
2OUT
2IN –
2IN +
NC
1OUT
1IN –
1IN +
V
CC–
/GND
1
2
3
4
5
10
9
8
7
6
TLC2262M, TLC2262AM ...U PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT
1IN–
1IN+
V
DD–
/GND
V
DD+
2OUT
2IN–
2IN+
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
NC
2OUT
NC
2IN–
NC
NC
1IN–
NC
1IN+
NC
NC
1OUT
NC
2IN+
NC
NC
NC
NC
V
DD+
V
DD–
TLC2262M, TLC2262AM . . . FK PACKAGE
(TOP VIEW)
/GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN–
1IN+
V
DD+
2IN+
2IN–
2OUT
4OUT
4IN–
4IN+
V
DD–
/GND
3IN+
3IN–
3OUT
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
4IN+
NC
V
CC–
/GND
NC
3IN+
1IN+
NC
V
CC+
NC
2IN+
1IN –
1OUT
NC
OUT
3IN –
4OUT
4IN –
2IN –
OUT
NC
TLC2264M, TLC2264AM . . . FK PACKAGE
(TOP VIEW)
TLC2264C, TLC2264AC
TLC2264I, TLC2264AI
TLC2264Q, TLC2264AQ
D, N, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN–
1IN+
V
DD+
2IN+
2IN–
2OUT
4OUT
4IN–
4IN+
V
DD–
/GND
3IN+
3IN–
3OUT
TLC2264M, TLC2264AM ...J OR W PACKAGE
(TOP VIEW)
Template Release Date: 7–11–94
TLC226x, TLC226xA
Advanced LinCMOS
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
RAIL-TO-RAIL
4
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
equivalent schematic (each amplifier)
Q3 Q6 Q9 Q12 Q14 Q16
Q2 Q5 Q7 Q8 Q10 Q11
D1
Q17Q15Q13
Q4Q1
R5
C1
V
DD+
IN+
IN–
R3 R4 R1 R2
OUT
V
DD–/ GND
ACTUAL DEVICE COMPONENT COUNT
†
COMPONENT TLC2262 TLC2264
Transistors 38 76
Resistors 28 56
Diodes 9 18
Capacitors 3 6
†
Includes both amplifiers and all ESD, bias, and trim circuitry
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
†
Supply voltage, V
DD+
(see Note 1) 8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply voltage, V
DD–
(see Note 1) –8 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, V
ID
(see Note 2) ±16 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, VI (any input, see Note 1) V
DD–
– 0.3 V to V
DD+
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current, II (each input) ±5 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current into V
DD+
±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current out of V
DD–
±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q suffix –40°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix –55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P, and PW packages 260°C. . . . . . .
J, JG, U, and W packages 300°C. . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between V
DD+
and V
DD –
.
2. Differential voltages are at IN+ with respect to IN–. Excessive current flows if input is brought below V
DD–
– 0.3 V.
3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
DISSIPATION RATING TABLE
T
≤ 25°C DERATING FACTOR T
= 70°C T
= 85°C T
= 125°C
PACKAGE
A
POWER RATING ABOVE TA = 25°CAPOWER RATINGAPOWER RATINGAPOWER RATING
D–8 725 mW 5.8 mW/°C 464 mW 377 mW 145 mW
D–14 950 mW 7.6 mW/°C 608 mW 494 mW 190 mW
FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
J 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
JG 1050 mW 8.4 mW/°C 672 mW 546 mW 210 mW
N 1150 mW 9.2 mW/°C 736 mW 598 mW 230 mW
P 1000 mW 8.0 mW/°C 640 mW 520 mW 200 mW
PW–8 525 mW 4.2 mW/°C 336 mW 273 mW 105 mW
PW–14 700 mW 5.6 mW/°C 448 mW 364 mW 140 mW
U 700 mW 5.5 mW/°C 452 mW 370 mW 150 mW
W 700 mW 5.5 mW/°C 452 mW 370 mW 150 mW
recommended operating conditions
C SUFFIX I SUFFIX Q SUFFIX M SUFFIX
MIN MAX MIN MAX MIN MAX MIN MAX
UNIT
Supply voltage, V
DD±
±2.2 ±8 ±2.2 ±8 ±2.2 ±8 ±2.2 ±8 V
Input voltage range, V
I
V
DD–VDD+
–1.5 V
DD–VDD+
–1.5 V
DD–VDD+
–1.5 V
DD–VDD+
–1.5 V
Common-mode input voltage, V
IC
V
DD–VDD+
–1.5 V
DD–VDD+
–1.5 V
DD–VDD+
–1.5 V
DD–VDD+
–1.5 V
Operating free-air temperature, T
A
0 70 –40 125 –40 125 –55 125 °C
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
TLC2262C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
p
25°C 300 2500
VIOInput offset voltage
Full range 3000
µ
V
α
VIO
Temperature coefficient of input offset voltage
25°C
to 70°C
2 µV/°C
Input offset voltage long-term drift
(see Note 4)
VIC = 0,
VO = 0,
VDD± = ±2.5 V,
RS = 50 Ω
25°C
0.003 µV/mo
p
O
S
25°C 0.5
p
IIOInput offset current
Full range 100
pA
p
25°C 1
p
IIBInput bias current
Full range 100
pA
p
25°C
0
to
4
–0.3
to
4.2
V
ICR
Common-mode input voltage range
R
S
= 50 Ω,
|V
IO
|
≤ 5 mV
Full range
0
to
3.5
V
IOH = –20 µA 25°C 4.99
25°C 4.85 4.94
V
OH
High-level output voltage
I
OH
= –
100 µA
Full range 4.82
V
25°C 4.70 4.85
I
OH
= –
400 µA
Full range 4.60
VIC = 2.5 V, IOL = 50 µA 25°C 0.01
25°C 0.09 0.15
V
IC
= 2.5 V,
I
OL
=
500 µA
Full range 0.15
V
OL
Low-level output voltage
25°C 0.2 0.3
V
V
IC
=
2.5 V
,
I
OL
=
1 m
A
Full range 0.3
25°C 0.7 1
V
IC
=
2.5 V
,
I
OL
=
4 m
A
Full range 1.2
25°C 80 170
A
VD
Large-signal differential voltage amplification
VIC = 2.5 V,
R
L
= 50
kΩ
‡
Full range 55
V/mV
VD
gg g
V
O
= 1 V to 4
V
RL = 1 MΩ
‡
25°C 550
r
i(d)
Differential input resistance 25°C
10
12
Ω
r
i(c)
Common-mode input resistance 25°C
10
12
Ω
c
i(c)
Common-mode input capacitance f = 10 kHz, P package 25°C 8 pF
z
o
Closed-loop output impedance f = 100 kHz, AV = 10 25°C 240 Ω
V
= 0 to 2.7 V, V
= 2.5 V,
25°C 70 83
CMRR
Common-mode rejection ratio
IC
,
O
,
RS = 50 Ω
Full range 70
dB
pp
V
= 4.4 V to 16 V,
25°C 80 95
k
SVR
Suppl
y-v
oltage rejection ratio (∆VDD/∆VIO)
DD
,
VIC = VDD/2, No load
Full range 80
dB
pp
25°C 400 500
IDDSupply current
V
O
= 2.5 V,
No load
Full range 500
µ
A
†
Full range is 0°C to 70°C.
‡
Referenced to 2.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV .
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262C operating characteristics at specified free-air temperature, VDD = 5 V
TLC2262C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
V
= 1.5 V to 3.5 V, R
= 50 kه,
25°C 0.35 0.55
SR
Slew rate at unity gain
O
,
CL = 100 pF
‡
L
,
Full range 0.3
V/µs
p
f = 10 Hz 25°C 40
VnEquivalent input noise voltage
f = 1 kHz 25°C 12
n
V/√H
z
Peak-to-peak equivalent input noise
f = 0.1 Hz to 1 Hz 25°C 0.7
V
N(PP)
q
voltage
f = 0.1 Hz to 10 Hz
25°C 1.3
µ
V
I
n
Equivalent input noise current 25°C 0.6
fA√Hz
p
VO = 0.5 V to 2.5 V,
AV = 1
°
0.017%
THD
+
N
Total harmonic distortion plus noise
f
= 20 kHz,
RL = 50 kΩ
‡
AV = 10
25°C
0.03%
Gain-bandwidth product
f = 10 kHz,
CL = 100 pF
‡
RL = 50 kه,
25°C 0.71 MHz
B
OM
Maximum output-swing bandwidth
V
O(PP)
= 2 V,
RL = 50 kه,
AV = 1,
CL = 100 pF
‡
25°C 185 kHz
=–
A
V
= 1,
Step = 0.5 V to 2.5 V ,
To 0.1%°6.4
tsSettling time
,
RL = 50 kه,
25°Cµs
L
CL = 100 pF
‡
To 0.01%
14.1
φ
m
Phase margin at unity gain
p
25°C 56°
Gain margin
R
L
= 50
kΩ
‡
,
C
L
=
100 pF
‡
25°C 11 dB
†
Full range is 0°C to 70°C.
‡
Referenced to 2.5 V
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262C electrical characteristics at specified free-air temperature, V
DD±
= ±5 V (unless
otherwise specified)
TLC2262C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
p
25°C 300 2500
VIOInput offset voltage
Full range 3000
µ
V
p
p
25°C
°
α
VIO
Temperature coefficient of input offset voltage
to 70°C
2µV/°C
Input offset voltage long-term drift (see Note 4)
VIC = 0,
VO = 0,
25°C
0.003 µV/mo
p
R
S
= 50
Ω
25°C 0.5
p
IIOInput offset current
Full range 100
pA
p
25°C 1
p
IIBInput bias current
Full range 100
pA
–5 –5.3
25°C
5to5.3
to
p
4 4.2
V
ICR
Common-mode input voltage range
|V
IO
| ≤5 mV,
R
S
= 50
Ω
–5
V
Full range
5
to
g
3.5
IO = –20 µA 25°C 4.99
25°C 4.85 4.94
V
OM+
Maximum positive peak output voltage
I
O
= –
100 µA
Full range 4.82
V
25°C 4.7 4.85
I
O
= –
400 µA
Full range 4.6
VIC = 0, IO = 50 µA 25°C –4.99
25°C –4.85 –4.91
V
IC
= 0,
I
O
=
500 µA
Full range –4.85
V
OM–
Maximum negative peak output voltage
25°C –4.7 –4.8
V
V
IC
= 0,
I
O
= 1
m
A
Full range –4.7
25°C –4 –4.3
V
IC
= 0,
I
O
= 4
m
A
Full range –3.8
25°C 80 200
A
VD
Large-signal differential voltage amplification VO = ±4 V
R
L
=
50 kΩ
Full range 55
V/mV
RL = 1 MΩ 25°C 1000
r
i(d)
Differential input resistance 25°C
10
12
Ω
r
i(c)
Common-mode input resistance 25°C
10
12
Ω
c
i(c)
Common-mode input capacitance f = 10 kHz, P package 25°C 8 pF
z
o
Closed-loop output impedance f = 100 kHz, AV = 10 25°C 220
Ω
V
= –5 V to 2.7 V,
25°C 75 88
CMRR
Common-mode rejection ratio
IC
,
VO = 0 V, RS = 50 Ω
Full range 75
dB
pp
V
= 2.2 V to ±8 V,
25°C 80 95
k
SVR
Suppl
y-v
oltage rejection ratio (∆V
DD±
/∆VIO)
DD±
,
VIC = 0, No load
Full range 80
dB
pp
25°C 425 500
IDDSupply current
V
O
= 0 V,
No load
Full range 500
µ
A
†
Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV .
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262C operating characteristics at specified free-air temperature, V
DD±
= ±5 V
TLC2262C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
25°C 0.35 0.55
SR Slew rate at unity gain
V
O
=
±1.9 V
,
=
p
R
L
=
50 kΩ
,
Full
V/µs
C
L
=
100 F
range
0.3
p
f = 10 Hz 25°C 43
VnEquivalent input noise voltage
f = 1 kHz 25°C 12
n
V/√H
z
Peak-to-peak equivalent input noise
f = 0.1 Hz to 1 Hz 25°C 0.8
V
N(PP)
q
voltage
f = 0.1 Hz to 10 Hz
25°C 1.3
µ
V
I
n
Equivalent input noise current 25°C 0.6
fA√Hz
p
VO = ±2.3 V,
AV = 1
°
0.014%
THD
+
N
Total harmonic distortion pulse duration
f
= 20 kHz,
RL = 50 kΩ
AV = 10
25°C
0.024%
p
f = 10 kHz, R
= 50 kΩ,
°
Gain-bandwidth product
,
CL = 100 pF
L
,
25°C
0.73
MH
z
p
V
O(PP
)
= 4.6 V, AV = 1,
°
BOMMaximum output-swing bandwidth
O(PP)
RL = 50 kΩ,
V
CL = 100 pF
25°C85kH
z
=–
A
V
= 1,
Step = –2.3 V to 2.3 V,
To 0.1%
°
7.1
tsSettling time
,
RL = 50 kΩ,
25°Cµs
L
CL = 100 pF
To 0.01%
16.5
φ
m
Phase margin at unity gain
p
25°C 57°
Gain margin
R
L
= 50 kΩ,
C
L
=
100 pF
25°C 11 dB
†
Full range is 0°C to 70°C.
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2264C electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
TLC2264C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
p
25°C 300 2500
VIOInput offset voltage
Full range 3000
µ
V
α
VIO
Temperature coefficient of input offset voltage
25°C
to 70°C
2 µV/°C
Input offset voltage long-term drift (see Note 4)
VIC = 0,
V
DD±
= ±2.5 V ,
25°C 0.003 µV/mo
p
V
O
= 0,
R
S
= 50
Ω
25°C 0.5
p
IIOInput offset current
Full range 100
pA
p
25°C 1
p
IIBInput bias current
Full range 100
pA
p
25°C
0
to
4
–0.3
to
4.2
V
ICR
Common-mode input voltage range
R
S
=
50 Ω
,
|V
IO
| ≤ 5 mV
Full range
0
to
3.5
V
IOH = –20 µA 25°C 4.99
25°C 4.85 4.94
V
OH
High-level output voltage
I
OH
= –
100 µA
Full range 4.82
V
25°C 4.70 4.85
I
OH
= –
400 µA
Full range 4.60
VIC = 2.5 V, IOL = 50 µA 25°C 0.01
25°C 0.09 0.15
V
IC
=
2.5 V
,
I
OL
=
500 µA
Full range 0.15
V
OL
Low-level output voltage
25°C 0.2 0.3
V
V
IC
= 2.5 V,
I
OL
= 1
m
A
Full range 0.3
25°C 0.7 1
V
IC
= 2.5 V,
I
OL
= 4
m
A
Full range 1.2
25°C 80 170
A
VD
Large-signal differential voltage amplification
VIC = 2.5 V,
R
L
=
50 kΩ
‡
Full range 55
V/mV
VD
gg g
V
O
= 1 V to 4
V
RL = 1 MΩ
‡
25°C 550
r
i(d)
Differential input resistance 25°C
10
12
Ω
r
i(c)
Common-mode input resistance 25°C
10
12
Ω
c
i(c)
Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF
z
o
Closed-loop output impedance f = 100 kHz, AV = 10 25°C 240 Ω
V
= 0 to 2.7 V , V
= 2.5 V,
25°C 70 83
CMRR
Common-mode rejection ratio
IC
,
RS = 50 Ω
O
,
Full range 70
dB
pp
VDD = 4.4 V to 16 V, 25°C 80 95
k
SVR
Suppl
y-v
oltage rejection ratio (∆VDD/∆VIO)
VIC = VDD/2, No load Full range 80
dB
pp
p
25°C 0.8 1
IDDSupply current (four amplifiers)
V
O
= 2.5 V,
No load
Full range 1
mA
†
Full range is 0°C to 70°C.
‡
Referenced to 2.5 V
NOTE 4. Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV .
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2264C operating characteristics at specified free-air temperature, VDD = 5 V
TLC2264C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
25°C 0.35 0.55
SR Slew rate at unity gain
V
O
= 1.4 V to 2.6 V,
=
p
‡
R
L
= 50
kΩ
‡
,
Full
V/µs
C
L
=
100 F
‡
range
0.3
p
f = 10 Hz 25°C 40
VnEquivalent input noise voltage
f = 1 kHz 25°C 12
n
V/√H
z
Peak-to-peak equivalent input noise
f = 0.1 Hz to 1 Hz 25°C 0.7
V
N(PP)
q
voltage
f = 0.1 Hz to 10 Hz
25°C 1.3
µ
V
I
n
Equivalent input noise current 25°C 0.6
fA/√Hz
p
VO = 0.5 V to 2.5 V,
AV = 1
°
0.017%
THD
+
N
Total harmonic distortion plus noise
f
= 20 kHz,
RL = 50 kΩ
‡
AV = 10
25°C
0.03%
Gain-bandwidth product
f = 10 kHz,
CL = 100 pF
‡
RL = 50 kه,
25°C 0.71 MHz
B
OM
Maximum output-swing bandwidth
V
O(PP)
= 2 V,
RL = 50 kه,
AV = 1,
CL = 100 pF
‡
25°C 185 kHz
=–
A
V
= 1,
Step = 0.5 V to 2.5 V ,
To 0.1%°6.4
tsSettling time
,
RL = 50 kه,
25°Cµs
L
CL = 100 pF
‡
To 0.01%
14.1
φ
m
Phase margin at unity gain
p
25°C
56°
Gain margin
R
L
= 50
kΩ
‡
,
C
L
=
100 pF
‡
25°C 11 dB
†
Full range is 0°C to 70°C.
‡
Referenced to 2.5 V
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2264C electrical characteristics at specified free-air temperature, V
DD±
= ±5 V (unless
otherwise specified)
TLC2264C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
p
25°C 300 2500
VIOInput offset voltage
Full range 3000
µ
V
p
p
25°C
°
α
VIO
Temperature coefficient of input offset voltage
to 70°C
2µV/°C
Input offset voltage long-term drift (see Note 4)
VIC = 0,
VO = 0,
25°C
0.003 µV/mo
p
R
S
= 50
Ω
25°C 0.5
p
IIOInput offset current
Full range 100
pA
p
25°C 1
p
IIBInput bias current
Full range 100
pA
–5 –5.3
25°C
5to5.3
to
p
4 4.2
V
ICR
Common-mode input voltage range
|V
IO
| ≤5 mV,
R
S
= 50
Ω
–5
V
Full range
5
to
g
3.5
IO = –20 µA 25°C 4.99
25°C 4.85 4.94
V
OM+
Maximum positive peak output voltage
I
O
= –
100 µA
Full range 4.82
V
25°C 4.7 4.85
I
O
= –
400 µA
Full range 4.6
VIC = 0, IO = 50 µA 25°C –4.99
25°C –4.85 –4.91
V
IC
= 0,
I
O
=
500 µA
Full range –4.85
V
OM–
Maximum negative peak output voltage
25°C –4.7 –4.8
V
V
IC
= 0,
I
O
= 1
m
A
Full range –4.7
25°C –4 –4.3
V
IC
=
0
,
I
O
=
4 m
A
Full range –3.8
25°C 80 200
A
VD
Large-signal differential voltage amplification VO = ±4 V
R
L
= 50
kΩ
Full range 55
V/mV
RL = 1 MΩ 25°C 1000
r
i(d)
Differential input resistance 25°C
10
12
Ω
r
i(c)
Common-mode input resistance 25°C
10
12
Ω
c
i(c)
Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF
z
o
Closed-loop output impedance f = 100 kHz, AV = 10 25°C 220 Ω
VIC = –5 V to 2.7 V, 25°C 75 88
CMRR
Common-mode rejection ratio
VO = 0, RS = 50 Ω Full range 75
dB
pp
V
DD±
= ±2.2 V to ±8 V, 25°C 80 95
k
SVR
Suppl
y-v
oltage rejection ratio (∆V
DD±
/∆VIO)
VIC = 0, No load Full range 80
dB
pp
p
25°C 0.85 1
IDDSupply current (four amplifiers)
V
O
= 0,
No load
Full range 1
mA
†
Full range is 0°C to 70°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV .
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2264C operating characteristics at specified free-air temperature, V
DD±
= ±5 V
TLC2264C
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX
UNIT
25°C 0.35 0.55
SR Slew rate at unity gain
V
O
=
±1.9 V
,
=
p
R
L
=
50 kΩ
,
Full
V/µs
C
L
=
100 F
range
0.3
p
f = 10 Hz 25°C 43
VnEquivalent input noise voltage
f = 1 kHz 25°C 12
n
V/√H
z
Peak-to-peak equivalent input noise
f = 0.1 Hz to 1 Hz 25°C 0.8
V
N(PP)
q
voltage
f = 0.1 Hz to 10 Hz
25°C 1.3
µ
V
I
n
Equivalent input noise current 25°C 0.6
fA/√Hz
p
VO = ± 2.3 V ,
AV = 1
°
0.014%
THD
+
N
Total harmonic distortion plus noise
f
= 20 kHz,
RL = 50 kΩ
AV = 10
25°C
0.024%
p
f = 10 kHz, R
= 50 kΩ,
°
Gain-bandwidth product
,
CL = 100 pF
L
,
25°C
0.73
MH
z
p
V
= 4.6 V, A
= 1,
°
BOMMaximum output-swing bandwidth
O(PP)
,
RL = 50 kΩ,
V
,
CL = 100 pF
25°C70kH
z
=–
A
V
= 1,
Step = –2.3 V to 2.3 V,
To 0.1%°7.1
tsSettling time
,
RL = 50 kΩ,
25°Cµs
L
CL = 100 pF
To 0.01%
16.5
φ
m
Phase margin at unity gain
p
25°C
57°
Gain margin
R
L
= 50 kΩ,
C
L
=
100 pF
25°C 11 dB
†
Full range is 0°C to 70°C.
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
TLC2262I TLC2262AI
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 300 2500 300 950
VIOInput offset voltage
Full range 3000 1500
µ
V
T emperature coef ficient 25°C
°
α
VIO
of input offset voltage to 85°C
2
2µV/°C
Input offset voltage
long-term drift
(see Note 4)
V
DD±
= ±2.5 V,
VO = 0,
VIC = 0,
RS = 50 Ω
25°C
0.003 0.003 µV/mo
p
25°C 0.5 0.5
p
IIOInput offset current
Full range 500 500
pA
p
25°C 1 1
p
IIBInput bias current
Full range 500 500
pA
0 –0.3 0 –0.3
25°C
to to to to
Common-mode input
4 4.2 4 4.2
V
ICR
voltage range
R
S
= 50 Ω,
|V
IO
| ≤5
mV
0 0
V
Full range
to to
g
3.5 3.5
IOH = –20 µA 25°C 4.99 4.99
25°C 4.85 4.94 4.85 4.94
V
OH
High-level output voltage
I
OH
= –
100 µA
Full range 4.82 4.82
V
25°C 4.7 4.85 4.7 4.85
I
OH
= –
400 µA
Full range 4.5 4.5
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
25°C 0.09 0.15 0.09 0.15
V
OL
Low-level output voltage
V
IC
= 2.5 V,
I
OL
=
500 µA
Full range 0.15 0.15
V
25°C 0.8 1 0.7 1
V
IC
= 2.5 V,
I
OL
= 4
m
A
Full range 1.2 1.2
25°C 80 100 80 170
A
VD
L
arge-signal
diff
erentia
l
p
V
IC
=
2.5 V
,
R
L
=
50 kΩ
‡
Full range 50 50
V/mV
VD
voltage am lification
V
O
= 1 V to 4
V
RL = 1 MΩ
‡
25°C 550 550
r
i(d)
Differential input
resistance
25°C 10
12
10
12
Ω
r
i(c)
Common-mode input
resistance
25°C 10
12
10
12
Ω
c
i(c)
Common-mode input
capacitance
f = 10 kHz, P package 25°C 8 8 pF
z
o
Closed-loop output
impedance
f = 100 kHz, AV = 10 25°C 240 240
Ω
Common-mode rejection VIC = 0 to 2.7 V, VO = 2.5 V,
25°C 70 83 70 83
CMRR
j
ratio
IC O
RS = 50 Ω
Full range 70 70
dB
Supply-voltage rejection VDD = 4.4 V to 16 V,
25°C 80 95 80 95
k
SVR
ygj
ratio (∆VDD/∆VIO)
DD
VIC = VDD/2, No load
Full range 80 80
dB
pp
25°C 400 500 400 500
IDDSupply current
V
O
= 2.5 V,
No load
Full range 500 500
µ
A
†
Full range is – 40°C to 125°C.
‡
Referenced to 2.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV .
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262I operating characteristics at specified free-air temperature, VDD = 5 V
TLC2262I TLC2262AI
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C
0.35 0.55 0.35 0.55
SR
Slew rate at unit
y
V
O
= 1.5 V to 3.5 V,
=
p
‡
R
L
= 50
kΩ
‡
,
Full
V/µs
gain
C
L
=
100 F
‡
range
0.25
0.25
Equivalent input
f = 10 Hz 25°C 40 40
V
n
q
noise voltage
f = 1 kHz
25°C 12 12
n
V/√H
z
Peak-to-peak
p
f = 0.1 Hz to 1 Hz 25°C 0.7 0.7
V
N(PP)
equivalent inpu
t
noise voltage
f = 0.1 Hz to 10 Hz
25°C 1.3 1.3
µ
V
I
n
Equivalent input
noise current
25°C 0.6 0.6
fA√Hz
Total harmonic
p
VO = 0.5 V to 2.5 V,
AV = 1
°
0.017% 0.017%
THD
+
N
distorti
on plus
noise
f
= 20 kHz,
RL = 50 kΩ
‡
AV = 10
25°C
0.03% 0.03%
Gain-bandwidth
f = 50 kHz
,
R
= 50 kΩ
‡
,
°
product
f 50 kHz,
CL = 100 pF
‡
R
L
50
kΩ ,
25°C
0.82
0.82
MH
z
Maximum output- V
= 2 V, A
= 1,
°
B
OM
swing bandwidth
O(PP)
,
RL = 50 kه,
V
,
CL = 100 pF
‡
25°C
185
185
kH
z
=–
A
V
= 1,
Step = 0.5 V to 2.5 V ,
To 0.1%°6.4
6.4
tsSettling time
,
RL = 50 kه,
25°Cµs
L
CL = 100 pF
‡
To 0.01%
14.1
14.1
φ
m
Phase margin at
unity gain
RL = 50 kه, CL = 100 pF
‡
25°C 56° 56°
Gain margin
L,L
25°C 11 11 dB
†
Full range is – 40°C to 125°C.
‡
Referenced to 2.5 V
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262I electrical characteristics at specified free-air temperature, V
DD±
= ±5 V (unless otherwise
noted)
TLC2262I TLC2262AI
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 300 2500 300 950
VIOInput offset voltage
Full range 3000 1500
µ
V
T emperature coef ficient of 25°C
°
α
VIO
input offset voltage to 85°C
2
2µV/°C
Input offset voltage
long-term drift
(see Note 4)
VIC = 0,
RS = 50 Ω
VO = 0,
25°C
0.003 0.003 µV/mo
p
25°C 0.5 0.5
p
IIOInput offset current
Full range 500 500
pA
p
25°C 1 1
p
IIBInput bias current
Full range 500 500
pA
°
–5 –5.3 –5 –5.3
Common-mode input
25°C
to 4 to 4.2 to 4 to 4.2
V
ICR
voltage range
R
S
= 50 Ω,
|V
IO
| ≤5
mV
–5 –5
V
Full range
to 3.5 to 3.5
IO = –20 µA 25°C 4.99 4.99
25°C 4.85 4.94 4.85 4.94
V
OM+
Maximum positive peak
p
I
O
= –
100 µA
Full range 4.82 4.82
V
out ut voltage
25°C 4.7 4.85 4.7 4.85
I
O
= –
400 µA
Full range 4.5 4.5
VIC = 0, IO = 50 µA 25°C –4.99 –4.99
25°C –4.85 –4.91 –4.85 –4.91
V
OM–
Maximum negative peak
p
V
IC
=
0
,
I
O
=
500 µA
Full range –4.85 –4.85
V
out ut voltage
25°C –4 –4.3 –4 –4.3
V
IC
= 0,
I
O
= 4
m
A
Full range –3.8 –3.8
25°C 80 200 80 200
A
VD
Large-signal differential
p
VO = ±4 V
R
L
= 50
kΩ
Full range 50 50
V/mV
voltage am lification
RL = 1 MΩ 25°C 1000 1000
r
i(d)
Differential input
resistance
25°C
10
12
10
12
Ω
r
i(c)
Common-mode input
resistance
25°C
10
12
10
12
Ω
c
i(c)
Common-mode input
capacitance
f = 10 kHz, P package 25°C 8 8 pF
z
o
Closed-loop output
impedance
f = 100 kHz, AV = 10 25°C 220 220
Ω
Common-mode V
= –5 V to 2.7 V,
25°C 75 88 75 88
CMRR
rejection ratio
IC
,
VO = 0, RS = 50 Ω
Full range 75 75
dB
Supply-voltage rejection V
= 4.4 V to 16 V,
25°C 80 95 80 95
k
SVR
ygj
ratio (∆V
DD±
/∆VIO)
DD
,
VIC = VDD/2, No load
Full range 80 80
dB
pp
25°C 425 500 425 500
IDDSupply current
V
O
=
2.5 V
,
No load
Full range 500 500
µ
A
†
Full range is – 40°C to 125°C.
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV .
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2262I operating characteristics at specified free-air temperature, V
DD±
= ±5 V
TLC2262I TLC2262AI
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
25°C 0.35 0.55 0.35 0.55
SR
Slew rate at unit
y
V
O
=
±1.9 V
,
=
p
R
L
=
50 kΩ
,
Full
V/µs
gain
C
L
=
100 F
range
0.25
0.25
Equivalent input
f = 10 Hz 25°C 43 43
V
n
q
noise voltage
f = 1 kHz
25°C 12 12
n
V/√H
z
Peak-to-peak
p
f = 0.1 Hz to 1 Hz 25°C 0.8 0.8
V
N(PP)
equivalent inpu
t
noise voltage
f = 0.1 Hz to 10 Hz
25°C 1.3 1.3
µ
V
I
n
Equivalent input
noise current
25°C 0.6 0.6
fA√Hz
Total harmonic
p
VO = ±2.3 V,
AV = 1
°
0.014% 0.014%
THD
+
N
distorti
on plus
noise
R
L
= 50 kΩ,
f = 20 kHz
AV = 10
25°C
0.024% 0.024%
Gain-bandwidth f =10 kHz, R
= 50 kΩ,
°
product
,
CL = 100 pF
L
,
25°C
0.73
0.73
MH
z
Maximum
p
V
= 4.6 V, A
= 1,
°
B
OM
output-swing
bandwidth
O(PP)
,
RL = 50 kΩ,
V
,
CL = 100 pF
25°C8585
kH
z
=–
A
V
= 1,
Step = –2.3 V to 2.3 V,
To 0.1%°7.1
7.1
tsSettling time
,
RL = 50 kΩ,
25°Cµs
L
CL = 100 pF
To 0.01%
16.5
16.5
φ
m
Phase margin at
unity gain
RL = 50 kΩ, CL = 100 pF
25°C 57° 57°
Gain margin
L
L
25°C 11 11 dB
†
Full range is –40°C to 125°C.
TLC226x, TLC226xA
Advanced LinCMOS RAIL-TO-RAIL
OPERATIONAL AMPLIFIERS
SLOS177A – FEBRUARY 1997 – REVISED JULY 1999
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC2264I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise
noted)
TLC2264I TLC2264AI
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
p
25°C 300 2500 300 950
VIOInput offset voltage
Full range 3000 1500
µ
V
α
VIO
T emperature coef ficient
of input offset voltage
25°C
to 125°C
2 2 µV/°C
Input offset voltage
long-term drift (see Note 4)
V
DD±
=±2.5 V ,
VO = 0,
VIC = 0,
RS = 50 Ω
25°C 0.003 0.003 µV/mo
p
25°C 0.5 0.5
p
IIOInput offset current
Full range 500 500
pA
p
25°C 1 1
p
IIBInput bias current
Full range 500 500
pA
Common-mode input
25°C
0
to
4
–0.3
to
4.2
0
to
4
–0.3
to
4.2
V
ICR
voltage range
R
S
= 50 Ω,
|V
IO
| ≤5
mV
Full range
0
to
3.5
0
to
3.5
V
IOH = –20 µA 25°C 4.99 4.99
25°C 4.85 4.94 4.85 4.94
V
OH
High-l
evel outpu
t
I
OH
= –
100 µA
Full range 4.82 4.82
V
voltage
25°C 4.7 4.85 4.7 4.85
I
OH
= –
400 µA
Full range 4.5 4.5
VIC = 2.5 V, IOL = 50 µA 25°C 0.01 0.01
25°C 0.09 0.15 0.09 0.15
V
OL
L
ow-level outpu
t
V
IC
=
2.5 V
,
I
OL
=
500 µA
Full range 0.15 0.15
V
voltage
25°C 0.8 1 0.7 1
V
IC
= 2.5 V,
I
OL
= 4
m
A
Full range 1.2 1.2
25°C 80 100 80 170
A
VD
L
arge-signal
diff
erentia
l
p
V
IC
= 2.5 V,
R
L
= 50
kΩ
‡
Full range 50 50
V/mV
VD
voltage am lification
V
O
= 1 V to 4
V
RL = 1 MΩ
‡
25°C 550 550
r
i(d)
Differential input
resistance
25°C 10
12
10
12
Ω
r
i(c)
Common-mode
input resistance
25°C 10
12
10
12
Ω
c
i(c)
Common-mode
input capacitance
f = 10 kHz, N package 25°C 8 8 pF
z
o
Closed-loop
output impedance
f = 100 kHz, AV = 10 25°C 240 240 Ω
Common-mode VIC = 0 to 2.7 V, VO = 2.5 V,
25°C 70 83 70 83
CMRR
rejection ratio
IC
RS = 50 Ω
O
Full range 70 70
dB
Supply-voltage
VDD = 4.4 V to 16 V,
25°C 80 95 80 95
k
SVR
rejection ratio
(∆VDD/∆VIO)
VIC = VDD/2,
No load
Full range
80 80
dB
Supply current
25°C 0.8 1 0.8 1
I
DD
y
(four amplifiers)
V
O
=
2.5 V
,
No load
Full range 1 1
mA
†
Full range is – 40°C to 125°C.
‡
Referenced to 2.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV .
Loading...