Texas Instruments SN74LVTH162374DGGR, SN74LVTH162374DL, SN74LVTH162374DLR, SNJ54LVTH162374WD Datasheet
SN54LVTH162374, SN74LVTH162374
3.3-V ABT 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS
WITH 3-STATE OUTPUTS
SCBS262I – JULY 1993 – REVISED APRIL 1999
D
Members of the Texas Instruments
Widebus
D
State-of-the-Art Advanced BiCMOS
Family
Technology (ABT) Design for 3.3-V
Operation and Low Static-Power
Dissipation
D
Output Ports Have Equivalent 22-Ω Series
Resistors, So No External Resistors Are
Required
D
Support Mixed-Mode Signal Operation
(5-V Input and Output Voltages With
3.3-V V
D
Support Unregulated Battery Operation
CC
)
Down to 2.7 V
D
Typical V
< 0.8 V at V
D
I
off
and Power-Up 3-State Support Hot
(Output Ground Bounce)
OLP
= 3.3 V, TA = 25°C
CC
Insertion
D
Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
D
Distributed VCC and GND Pin Configuration
Minimizes High-Speed Switching Noise
D
Flow-Through Architecture Optimizes PCB
Layout
D
Latch-Up Performance Exceeds 500 mA Per
JESD 17
D
ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
D
Package Options Include Plastic Shrink
Small-Outline (DL) and Thin Shrink
Small-Outline (DGG) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
Using 25-mil Center-to-Center Spacings
SN54LVTH162374. . . WD PACKAGE
SN74LVTH162374. . . DGG OR DL PACKAGE
1OE
1Q1
1Q2
GND
1Q3
1Q4
V
CC
1Q5
1Q6
GND
1Q7
1Q8
2Q1
2Q2
GND
2Q3
2Q4
V
CC
2Q5
2Q6
GND
2Q7
2Q8
2OE
(TOP VIEW)
1
48
2
47
3
46
4
45
5
44
6
43
7
42
8
41
9
40
10
39
11
38
12
37
13
36
14
35
15
34
16
33
17
32
18
31
19
30
20
29
21
28
22
27
23
26
24
25
1CLK
1D1
1D2
GND
1D3
1D4
V
CC
1D5
1D6
GND
1D7
1D8
2D1
2D2
GND
2D3
2D4
V
CC
2D5
2D6
GND
2D7
2D8
2CLK
description
The ’LVTH162374 devices are 16-bit edge-triggered D-type flip-flops with 3-state outputs designed for
low-voltage (3.3-V) V
environment. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers,
and working registers.
These devices can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock
(CLK), the Q outputs of the flip-flop take on the logic levels set up at the D inputs.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus is a trademark of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
operation, but with the capability to provide a TTL interface to a 5-V system
CC
Copyright 1999, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
1
SN54LVTH162374, SN74LVTH162374
3.3-V ABT 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS
WITH 3-STATE OUTPUTS
SCBS262I – JULY 1993 – REVISED APRIL 1999
description (continued)
A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high
or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive
the bus lines significantly . The high-impedance state and the increased drive provide the capability to drive bus
lines without need for interface or pullup components.
OE
does not affect internal operations of the flip-flop. Old data can be retained or new data can be entered while
the outputs are in the high-impedance state.
The outputs, which are designed to source or sink up to 12 mA, include equivalent 22-Ω series resistors to
reduce overshoot and undershoot.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level.
When V
However, to ensure the high-impedance state above 1.5 V, OE
is between 0 and 1.5 V , the devices are in the high-impedance state during power up or power down.
CC
should be tied to VCC through a pullup resistor;
the minimum value of the resistor is determined by the current-sinking capability of the driver.
These devices are fully specified for hot-insertion applications using I
and power-up 3-state. The I
off
circuitry
off
disables the outputs, preventing damaging current backflow through the devices when they are powered down.
The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down,
which prevents driver conflict.
The SN54L VTH162374 is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74LVTH162374 is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
(each flip-flop)
INPUTS
CLK D
OE
L ↑ H H
L ↑ LL
LH or L X Q
H X X Z
OUTPUT
Q
0
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN54LVTH162374, SN74LVTH162374
3.3-V ABT 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS
WITH 3-STATE OUTPUTS
SCBS262I – JULY 1993 – REVISED APRIL 1999
logic symbol
†
1D1
1D2
1D3
1D4
1D5
1D6
1D7
1D8
2D1
2D2
2D3
2D4
2D5
2D6
2D7
2D8
1
48
24
25
47
46
44
43
41
40
38
37
36
35
33
32
30
29
27
26
1EN
2EN
1D
2D
C1
C2
11
12
13
14
16
17
19
20
22
23
2
1Q1
3
1Q2
5
1Q3
6
1Q4
8
1Q5
9
1Q6
1Q7
1Q8
2Q1
2Q2
2Q3
2Q4
2Q5
2Q6
2Q7
2Q8
1
2
1OE
1CLK
2OE
2CLK
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
logic diagram (positive logic)
1OE
1CLK
1D1
1
48
47
C1
1D
To Seven Other Channels
2CLK
1Q1
2OE
2D1
24
25
36
C1
1D
To Seven Other Channels
132
2Q1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
Loading...