Texas Instruments SN74LVCR2245ADBLE, SN74LVCR2245ADBR, SN74LVCR2245ADGVR, SN74LVCR2245ADW, SN74LVCR2245ADWR Datasheet
...
SN74LVCR2245A
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS581D – NOVEMBER 1996 – REVISED JUNE 1998
D
EPIC
(Enhanced-Performance Implanted
CMOS) Submicron Process
D
All Outputs Have Equivalent 26-Ω Series
Resistors, So No External Resistors Are
Required
D
Typical V
< 0.8 V at V
D
Typical V
> 2 V at V
D
Power Off Disables Outputs, Permitting
(Output Ground Bounce)
OLP
= 3.3 V, TA = 25°C
CC
(Output VOH Undershoot)
OHV
= 3.3 V, TA = 25°C
CC
Live Insertion
D
Supports Mixed-Mode Signal Operation on
All Ports (5-V Input/Output Voltage With
3.3-V V
D
ESD Protection Exceeds 2000 V Per
CC
)
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
D
Latch-Up Performance Exceeds 250 mA Per
JESD 17
D
Package Options Include Plastic
Small-Outline (DW), Shrink Small-Outline
(DB), and Thin Shrink Small-Outline (PW)
Packages
DB, DW, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
OE
B1
B2
B3
B4
B5
B6
B7
B8
CC
DIR
A1
A2
A3
A4
A5
A6
A7
A8
GND
description
This octal bus transceiver is designed for 1.65-V to 3.6-V VCC operation.
The SN74LVCR2245A is designed for asynchronous communication between data buses. The device
transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE
effectively isolated.
All outputs, which are designed to sink up to 12 mA, include equivalent 26-W resistors to reduce overshoot and
undershoot.
Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators
in a mixed 3.3-V/5-V system environment.
T o ensure the high-impedance state during power up or power down, OE
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN74LVCR2245A is characterized for operation from –40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
) input can be used to disable the device so the buses are
should be tied to VCC through a pullup
EPIC is a trademark of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 1998, Texas Instruments Incorporated
1
SN74LVCR2245A
OPERATION
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS581D – NOVEMBER 1996 – REVISED JUNE 1998
FUNCTION TABLE
INPUTS
OE DIR
L L B data to A bus
L H A data to B bus
H X Isolation
logic symbol
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
†
OE
DIR
A1
A2
A3
A4
A5
A6
A7
A8
19
1
2
3
4
5
6
7
8
9
G3
3 EN1 [BA]
3 EN2 [AB]
1
2
logic diagram (positive logic)
1
DIR
18
17
16
15
14
13
12
11
B1
B2
B3
B4
B5
B6
B7
B8
A1
19
OE
2
18
B1
To Seven Other Channels
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
VCCSuppl
oltage
V
VOOutput voltage
V
IOHHigh-level output current
mA
IOLLow-level output current
mA
SN74LVCR2245A
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS581D – NOVEMBER 1996 – REVISED JUNE 1998
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
Input voltage range, V
Voltage range applied to any output in the high-impedance or power-off state, V
–0.5 V to 6.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC
: (see Note 1) –0.5 V to 6.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I
O
†
(see Note 1) –0.5 V to 6.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage range applied to any output in the high or low state, V
O
(see Notes 1 and 2) –0.5 V to VCC + 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input clamp current, I
Output clamp current, I
Continuous output current, I
Continuous current through V
Package thermal impedance, θ
(VI < 0) –50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IK
(VO < 0) –50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OK
±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
or GND ±100 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC
(see Note 3): DB package 115°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JA
DW package 97°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PW package 128°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The value of VCC is provided in the recommended operating conditions table.
3. The package thermal impedance is calculated in accordance with JESD 51.
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
recommended operating conditions (see Note 4)
MIN MAX UNIT
pp
y v
V
V
V
∆t/∆v Input transition rise or fall rate 0 10 ns/V
T
NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
High-level input voltage
IH
Low-level input voltage
IL
Input voltage 0 5.5 V
I
p
p
p
Operating free-air temperature –40 85 °C
A
Implications of Slow or Floating CMOS Inputs
, literature number SCBA004.
Operating 1.65 3.6
Data retention only 1.5
VCC = 1.65 V to 1.95 V 0.65 × V
VCC = 2.3 V to 2.7 V 1.7
VCC = 2.7 V to 3.6 V 2
VCC = 1.65 V to 1.95 V 0.35 × V
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V 0.8
High or low state 0 V
3 state 0 5.5
VCC = 1.65 V –2
VCC = 2.3 V –4
VCC = 2.7 V –8
VCC = 3 V –12
VCC = 1.65 V 2
VCC = 2.3 V 4
VCC = 2.7 V 8
VCC = 3 V 12
CC
0.7
CC
V
CC
V
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
Loading...