Texas Instruments SN74LV540ADW, SN74LV540ADWR, SN74LV540APWR, SN74LV540ADBR, SN74LV540ADGVR Datasheet
SN54LV540A, SN74LV540A
OCTAL BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS409B – APRIL 1998 – REVISED NOVEMBER 1998
D
EPIC
(Enhanced-Performance Implanted
CMOS) Process
D
Typical V
< 0.8 V at V
D
Typical V
> 2 V at V
D
Latch-Up Performance Exceeds 250 mA Per
(Output Ground Bounce)
OLP
= 3.3 V, TA = 25°C
CC
(Output VOH Undershoot)
OHV
= 3.3 V, TA = 25°C
CC
JESD 17
D
ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
D
Package Options Include Plastic
Small-Outline (DW, NS), Shrink
Small-Outline (DB), Thin Very Small-Outline
(DGV), and Thin Shrink Small-Outline (PW)
Packages, Ceramic Flat (W) Packages, Chip
Carriers (FK), and DIPs (J)
description
The ’LV540A devices are octal buffers/drivers
designed for 2-V to 5.5-V V
These devices are ideal for driving bus lines or
buffer memory address registers. They feature
inputs and outputs on opposite sides of the
package to facilitate printed circuit board layout.
The 3-state control gate is a two-input AND gate
with active-low inputs so that if either
output-enable (OE1
or OE2) input is high, all
corresponding outputs are in the high-impedance
state. The outputs provide inverted data when
they are not in the high-impedance state.
operation.
CC
SN74LV540A. . . DB, DGV, DW, NS, OR PW PACKAGE
SN54LV540A...J OR W PACKAGE
(TOP VIEW)
OE1
1
A1
2
A2
3
A3
4
A4
5
A5
6
A6
7
A7
8
9
A8
GND
SN54LV540A. . . FK PACKAGE
A3
A4
A5
A6
A7
10
(TOP VIEW)
A2A1OE1
3212019
4
5
6
7
8
910111213
A8
GND
Y8
20
19
18
17
16
15
14
13
12
11
V
CC
Y7
V
CC
OE2
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
18
17
16
15
14
Y6 OE2
Y1
Y2
Y3
Y4
Y5
T o ensure the high-impedance state during power up or power down, OE
should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN54LV540A is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74LV540A is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
(each buffer/driver)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
EPIC is a trademark of Texas Instruments Incorporated.
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
INPUTS
OE1 OE2 A
L L L H
L LH L
HXX Z
XHX Z
OUTPUT
Y
Copyright 1998, Texas Instruments Incorporated
1
SN54LV540A, SN74LV540A
OCTAL BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS409B – APRIL 1998 – REVISED NOVEMBER 1998
logic symbol
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
†
OE1
OE2
A1
A2
A3
A4
A5
A6
A7
A8
1
19
2
3
4
5
6
7
8
9
&
EN
1
logic diagram (positive logic)
1
OE1
19
OE2
2
A1
18
Y1
18
17
16
15
14
13
12
11
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
To Seven Other Channels
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
Input voltage range, V
Output voltage range applied in the high or low state, V
Output voltage range applied in high-impedance or power-off state, V
Input clamp current, I
Output clamp current, I
Continuous output current, I
Continuous current through V
Package thermal impedance, θ
Storage temperature range, T
‡
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. This value is limited to 7 V maximum.
3. The package thermal impedance is calculated in accordance with JESD 51.
–0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC
(see Note 1) –0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I
(VI < 0) –20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IK
(VO < 0 or VO > VCC) ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OK
(VO = 0 to VCC) ±35 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
or GND ±70 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC
(see Note 3): DB package 115°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JA
(see Notes 1 and 2) –0.5 V to VCC + 0.5 V. . . . . .
O
(see Note 1) –0.5 V to 7 V. . . . . . .
O
DGV package 146°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DW package 97°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NS package 100°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PW package 128°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
‡
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
UNIT
VIHHigh-level input voltage
V
VILLow-level input voltage
V
VOOutput voltage
V
IOHHigh-level output current
IOLLow-level output current
SN54LV540A, SN74LV540A
OCTAL BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS409B – APRIL 1998 – REVISED NOVEMBER 1998
recommended operating conditions (see Note 4)
SN54LV540A SN74LV540A
MIN MAX MIN MAX
V
V
∆t/∆v Input transition rise or fall rate
T
NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Supply voltage 2 5.5 2 5.5 V
CC
VCC = 2 V 1.5 1.5
p
p
Input voltage 0 5.5 0 5.5 V
I
p
p
p
Operating free-air temperature –55 125 –40 85 °C
A
Implications of Slow or Floating CMOS Inputs
VCC = 2.3 V to 2.7 V VCC× 0.7 VCC× 0.7
VCC = 3 V to 3.6 V VCC× 0.7 VCC× 0.7
VCC = 4.5 V to 5.5 V VCC× 0.7 VCC× 0.7
VCC = 2 V 0.5 0.5
VCC = 2.3 V to 2.7 V VCC× 0.3 VCC× 0.3
VCC = 3 V to 3.6 V VCC× 0.3 VCC× 0.3
VCC = 4.5 V to 5.5 V VCC× 0.3 VCC× 0.3
High or low state 0 V
3-state 0 5.5 0 5.5
VCC = 2 V –50 –50 µA
VCC = 2.3 V to 2.7 V –2 –2
VCC = 3 V to 3.6 V –8 –8
VCC = 4.5 V to 5.5 V –16 –16
VCC = 2 V 50 50 µA
VCC = 2.3 V to 2.7 V 2 2
VCC = 3 V to 3.6 V 8 8
VCC = 4.5 V to 5.5 V 16 16
VCC = 2.3 V to 2.7 V 0 200 0 200
VCC = 3 V to 3.6 V 0 100 0 100
VCC = 4.5 V to 5.5 V 0 20 0 20
, literature number SCBA004.
CC
0 V
CC
mA
mA
ns/V
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
Loading...