Texas Instruments SN74LV373ADBR, SN74LV373ADGVR, SN74LV373ADW, SN74LV373ADWR, SN74LV373APWR Datasheet
SN54LV373A, SN74LV373A
OCTAL TRANSPARENT D-TYPE LATCHES
WITH 3-STATE OUTPUTS
SCLS407A – APRIL 1998 – REVISED JUNE 1998
D
EPIC
(Enhanced-Performance Implanted
CMOS) Process
D
Typical V
< 0.8 V at V
D
Typical V
> 2 V at V
D
Latch-Up Performance Exceeds 250 mA Per
(Output Ground Bounce)
OLP
, TA = 25°C
CC
(Output VOH Undershoot)
OHV
, TA = 25°C
CC
JESD 17
D
ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
D
Package Options Include Plastic
Small-Outline (DW, NS), Shrink
Small-Outline (DB), Thin Very Small-Outline
(DGV), and Thin Shrink Small-Outline (PW)
Packages, Ceramic Flat (W) Packages, Chip
Carriers (FK), and DIPs (J)
description
The ’L V373A devices are octal transparent D-type
latches designed for 2-V to 5.5-V V
While the latch-enable (LE) input is high, the
Q outputs follow the data (D) inputs. When LE is
taken low, the Q outputs are latched at the logic
levels set up at the D inputs.
A buffered output-enable (OE
to place the eight outputs in either a normal logic
state (high or low) or the high-impedance state. In
the high-impedance state, the outputs neither
load nor drive the bus lines significantly. The
high-impedance state and increased drive
provide the capability to drive bus lines without
need for interface or pullup components.
CC
) input can be used
operation.
SN74LV373A. . . DB, DGV, DW, NS, OR PW PACKAGE
SN54LV373A...J OR W PACKAGE
(TOP VIEW)
OE
1
1Q
2
1D
3
2D
4
2Q
5
3Q
6
3D
7
4D
8
4Q
9
GND
SN54LV373A. . . FK PACKAGE
2D
2Q
3Q
3D
4D
10
(TOP VIEW)
1D1QOE
3212019
4
5
6
7
8
910111213
4Q
GND
LE
20
19
18
17
16
15
14
13
12
11
CC
V
5Q
V
8Q
8D
7D
7Q
6Q
6D
5D
5Q
LE
8Q
18
17
16
15
14
5D
CC
8D
7D
7Q
6Q
6D
OE
does not affect the internal operations of the latches. Old data can be retained or new data can be entered
while the outputs are in the high-impedance state.
T o ensure the high-impedance state during power up or power down, OE
should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN54LV373A is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74LV373A is characterized for operation from –40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
EPIC is a trademark of Texas Instruments Incorporated.
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 1998, Texas Instruments Incorporated
1
SN54LV373A, SN74LV373A
OCTAL TRANSPARENT D-TYPE LATCHES
WITH 3-STATE OUTPUTS
SCLS407A – APRIL 1998 – REVISED JUNE 1998
FUNCTION TABLE
INPUTS
OE LE D
L H H H
L HL L
LLX Q
HXX Z
(each latch)
OUTPUT
Q
0
logic symbol
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
†
OE
LE
1D
2D
3D
4D
5D
6D
7D
8D
1
11
3
4
7
8
13
14
17
18
EN
C1
1D
logic diagram (positive logic)
1
OE
11
LE
12
15
16
19
2
1Q
5
2Q
6
3Q
9
4Q
5Q
6Q
7Q
8Q
3
1D
To Seven Other Channels
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
C1
1D
2
1Q
SN54LV373A, SN74LV373A
OCTAL TRANSPARENT D-TYPE LATCHES
WITH 3-STATE OUTPUTS
SCLS407A – APRIL 1998 – REVISED JUNE 1998
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
Input voltage range, V
Output voltage range, V
Input clamp current, I
Output clamp current, I
Continuous output current, I
Continuous current through V
Package thermal impedance, θ
Storage temperature range, T
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. This value is limited to 7 V maximum.
3. The package thermal impedance is calculated in accordance with JESD 51.
–0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC
(see Note 1) –0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I
(see Notes 1 and 2) –0.5 V to VCC + 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
(VI < 0) –20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IK
(VO < 0 or VO > VCC) ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OK
(VO = 0 to VCC) ±35 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
or GND ±70 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CC
(see Note 3): DB package 115°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JA
DGV package 146°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DW package 97°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NS package 100°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PW package 128°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
†
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
Loading...