Packages, Ceramic Chip Carriers, and
Standard and Ceramic 300-mil DIPs
description
These monolithic hex buffers/drivers feature
high-voltage open-collector outputs to interface
with high-level circuits or for driving high-current
loads. They are also characterized for use as
buffers for driving TTL inputs. The ′LS07 has a
rated output voltage of 30 V and the ′LS17 has a
rated output voltage of 15 V. The maximum sink
current is 30 mA for the SN54LS07 and 40 mA for
the SN74LS07 and SN74LS17.
SN54LS07 . . . J PACKAGE
SN74LS07, SN74LS17 . . . D OR N PACKAGE
(T0P VIEW)
1A
1
1Y
2
2A
3
2Y
4
3A
5
3Y
6
GND
SN54LS07 . . . FK PACKAGE
7
(T0P VIEW)
1Y1ANC
2A
NC
2Y
NC
3A
3 2 1 20 19
4
5
6
7
8
910111213
14
13
12
11
10
9
8
CC
V
6A
18
17
16
15
14
V
6A
6Y
5A
5Y
4A
4Y
CC
6Y
NC
5A
NC
5Y
These circuits are compatible with most TTL
families. Inputs are diode-clamped to minimize
transmission-line effects, which simplifies design.
Typical power dissipation is 140 mW and average
3Y
NC – No internal connection
GND
NC
4Y
4A
propagation delay time is 12 ns.
The SN54LS07 is characterized over the full military temperature range of –55°C to 125°C. The SN74LS07 and
SN74LS17 are characterized for operation from 0°C to 70°C.
1A
2A
3A
4A
5A
6A
1
3
5
9
11
13
†
2
1Y
4
2Y
6
3Y
8
4Y
10
5Y
12
6Y
logic diagram (positive logic)
1
1A
3
2A
5
3A
9
4A
11
5A
13
6A
10
12
2
1Y
4
2Y
6
3Y
8
4Y
5Y
6Y
logic symbol
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
Pin numbers shown are for D, J, and N packages.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 1991, Texas Instruments Incorporated
1
SN54LS07, SN74LS07, SN74LS17
HEX BUFFERS/DRIVERS WITH
OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS
schematic (each gate)
V
CC
9 kΩ
5 kΩ
Input
2 kΩ
1 kΩ
Output
2 kΩ
GND
Resistor values shown are nominal.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, V
Input voltage, V
Output voltage, V
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Voltage values are with respect to network ground terminal.
2. This is the maximum voltage that should be applied to any output when it is in the off state.
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETERTEST CONDITIONS
V
IK
I
OH
V
OL
I
I
I
IH
I
IL
I
CCH
I
†
‡
§
CCL
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
All typical values are at VCC = 5 V, TA = 25°C.
IOL = 30 mA for SN54 series parts and 40 mA for SN74 series parts.
switching characteristics, VCC = 5 V, TA = 25°C (see Note 3)
PARAMETERTEST CONDITIONSMINTYPMAXUNIT
t
PLH
t
PHL
NOTE 3: Load circuit and voltage waveforms are shown in Section 1 of
FROMTO
(INPUT)(OUTPUT)
AYR
= 110 Ω,C
L
TTL Logic Data Book,
= 15 pFns
L
1988.
610
1930
mA
V
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
IMPORTANT NOTICE
T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty . Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERT AIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOL VE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICA TIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERST OOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1998, Texas Instruments Incorporated
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.