TEXAS INSTRUMENTS SN54HC174, SN74HC174 Technical data
SN54HC174, SN74HC174
HEX D-TYPE FLIP-FLOPS
WITH CLEAR
SCLS119B – DECEMBER 1982 – REVISED MAY 1997
D
Contain Six Flip-Flops With Single-Rail
Outputs
D
Applications Include:
– Buffer/Storage Registers
– Shift Registers
– Pattern Generators
D
Package Options Include Plastic
Small-Outline (D) and Ceramic Flat (W)
Packages, Ceramic Chip Carriers (FK), and
Standard Plastic (N) and Ceramic (J)
300-mil DIPs
description
These monolithic positive-edge-triggered D-type
flip-flops have a direct clear (CLR) input.
Information at the data (D) inputs meeting the
setup time requirements is transferred to the
outputs on the positive-going edge of the clock
(CLK) pulse. Clock triggering occurs at a
particular voltage level and is not directly related
to the transition time of the positive-going edge of
CLK. When CLK is at either the high or low level,
the D input has no effect at the output.
SN54HC174 ...J OR W PACKAGE
SN74HC174 . . . D OR N PACKAGE
SN54HC174 . . . FK PACKAGE
1D
2D
NC
2Q
3D
(TOP VIEW)
CLR
1
1Q
2
1D
3
2D
4
2Q
5
3D
6
3Q
7
GND
8
(TOP VIEW)
1Q
3212019
4
5
6
7
8
910111213
CLR
NC
16
15
14
13
12
11
10
9
V
CC
V
CC
6Q
6D
5D
5Q
4D
4Q
CLK
6Q
18
17
16
15
14
6D
5D
NC
5Q
4D
The SN54HC174 is characterized for operation
over the full military temperature range of –55°C
to 125°C. The SN74HC174 is characterized for
operation from –40°C to 85°C.
FUNCTION TABLE
(each flip-flop)
INPUTS
CLR CLK D
L X X L
H ↑ HH
H ↑ LL
H L X Q
OUTPUT
Q
0
NC
CLK
4Q
3Q
GND
NC – No internal connection
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 1997, Texas Instruments Incorporated
1
SN54HC174, SN74HC174
HEX D-TYPE FLIP-FLOPS
WITH CLEAR
SCLS119B – DECEMBER 1982 – REVISED MAY 1997
logic symbol
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
Pin numbers shown are for the D, J, N, and W packages.
†
CLR
CLK
1D
2D
3D
4D
5D
6D
1
9
3
4
6
11
13
14
R
C1
1D
logic diagram (positive logic)
1
CLR
9
CLK
1D
3
1D
C1
R
10
12
15
2
1Q
5
2Q
7
3Q
4Q
5Q
6Q
2
1Q
To Five Other Channels
Pin numbers shown are for the D, J, N, and W packages.
absolute maximum ratings over operating free-air temperature range
‡
Supply voltage range, VCC –0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) ±20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 1) ±20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous output current, I
(VO = 0 to VCC) ±25 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O
Continuous current through VCC or GND ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θ
(see Note 2): D package 113°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JA
N package 78°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
‡
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51, except for through-hole packages, which use a trace
length of zero.
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Loading...