Texas Instruments JM38510-12902BPA, JM38510-12905BPA, JM38510-12903BPA, SN55451BJG, SN55452BJG Datasheet
...
SN55451B, SN55452B, SN55453B, SN55454B
SN75451B, SN75452B, SN75453B, SN75454B
DUAL PERIPHERAL DRIVERS
SLRS021B – DECEMBER 1976 – REVISED SEPTEMBER 1999
PERIPHERAL DRIVERS FOR
HIGH-CURRENT SWITCHING AT
VERY HIGH SPEEDS
D
Characterized for Use to 300 mA
D
High-Voltage Outputs
D
No Output Latch-Up at 20 V (After
Conducting 300 mA)
D
High-Speed Switching
D
Circuit Flexibility for Varied Applications
D
TTL-Compatible Diode-Clamped Inputs
D
Standard Supply Voltages
D
Plastic DIP (P) With Copper Lead Frame
Provides Cooler Operation and Improved
Reliability
D
Package Options Include Plastic
Small-Outline Packages, Ceramic Chip
Carriers, and Standard Plastic and Ceramic
300-mil DIPs
SUMMARY OF DEVICES
DEVICE
SN55451B AND FK, JG
SN55452B NAND JG
SN55453B OR FK, JG
SN55454B NOR JG
SN75451B AND D, P
SN75452B NAND D, P
SN75453B OR D, P
SN75454B NOR D, P
LOGIC OF
COMPLETE CIRCUIT
PACKAGES
SN55451B, SN55452B,
SN55453B, SN55454B . . . JG PACKAGE
SN75451B, SN75452B,
SN75453B, SN75454B ...D OR P PACKAGE
(TOP VIEW)
NC
8
7
6
5
CC
V
2Y
18
17
16
15
14
V
2B
2A
2Y
CC
NC
2B
NC
2A
NC
1A
1
1B
2
1Y
3
GND
SN55453B, SN55454B . . . FK PACKAGE
NC
1B
NC
1Y
NC
NC – No internal connection
4
SN55451B, SN55452B
(TOP VIEW)
NC1ANCNCNC
3 2 1 20 19
4
5
6
7
8
910111213
NC
GND
description
The SN55451B through SN55454B and SN75451B through SN75454B are dual peripheral drivers designed
for use in systems that employ TTL logic. This family is functionally interchangeable with and replaces the
SN75450 family and the SN75450A family devices manufactured previously . The speed of the devices is equal
to that of the SN75450 family, and the parts are designed to ensure freedom from latch-up. Diode-clamped
inputs simplify circuit design. Typical applications include high-speed logic buf fers, power drivers, relay drivers,
lamp drivers, MOS drivers, line drivers, and memory drivers.
The SN55451B/SN75451B, SN55452B/SN75452B, SN55453B/SN75453B, and SN55454B/SN75454B are
dual peripheral AND, NAND, OR, and NOR drivers, respectively (assuming positive logic), with the output of
the logic gates internally connected to the bases of the npn output transistors.
The SN55’ drivers are characterized for operation over the full military range of –55°C to 125°C. The SN75’
drivers are characterized for operation from 0°C to 70°C.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 1999, Texas Instruments Incorporated
1
SN55451B, SN55452B, SN55453B, SN55454B
PACKAGE
A
UNIT
SN75451B, SN75452B, SN75453B, SN75454B
DUAL PERIPHERAL DRIVERS
SLRS021B – DECEMBER 1976 – REVISED SEPTEMBER 1999
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
SN55’ SN75’ UNIT
Supply voltage, VCC (see Note 1) 7 7 V
Input voltage, V
Inter-emitter voltage (see Note 2) 5.5 5.5 V
Off-state output voltage, V
Continuous collector or output current, IOK (see Note 3) 400 400 mA
Peak collector or output current, II (tw ≤ 10 ms, duty cycle ≤ 50%, see Note 4) 500 500 mA
Continuous total power dissipation See Dissipation Rating Table
Operating free-air temperature range, T
Storage temperature range, T
Case temperature for 60 seconds FK package 260 °C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds JG package 300 °C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds D or P package 260 °C
NOTES: 1. Voltage values are with respect to network GND, unless otherwise specified.
I
O
A
stg
2. This is the voltage between two emitters of a multiple-emitter transistor.
3. This value applies when the base-emitter resistance (RBE) is equal to or less than 500 Ω.
4. Both halves of these dual circuits may conduct rated current simultaneously; however , power dissipation averaged over a short time
interval must fall within the continuous dissipation rating.
5.5 5.5 V
30 30 V
–55 to 125 0 to 70 °C
–65 to 150 –65 to 150 °C
T
≤ 25°C DERATING FACTOR T
POWER RATING ABOVE TA = 25°CAPOWER RATINGAPOWER RATING
D 725 mW 5.8 mW/°C 464 mW —
FK 1375 mW 11.0 mW/°C 880 mW 275 mW
JG 1050 mW 8.4 mW/°C 672 mW 210 mW
P 1000 mW 8.0 mW/°C 640 mW —
recommended operating conditions
Supply voltage, V
High-level input voltage, V
Low-level input voltage, V
Operating free-air temperature, T
CC
IH
IL
A
DISSIPATION RATING TABLE
MIN NOM MAX MIN NOM MAX
–55 125 0 70 °C
= 70°C T
SN55’ SN75’
4.5 5 5.5 4.75 5 5.25 V
2 2 V
= 125°C
0.8 0.8 V
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER
TEST CONDITIONS
‡
UNIT
CC
IL
0.25
0.5
0.25
0.4
VOLLow-level output voltage
V
CC
IL
0.5
0.8
0.5
0.7
IOHHigh-level output current
CC
IH
300
100µA
O
ns
VOHHigh-level output voltage after switching
S
,
O
,
mV
SN55451B, SN55452B, SN55453B, SN55454B
SN75451B, SN75452B, SN75453B, SN75454B
DUAL PERIPHERAL DRIVERS
SLRS021B – DECEMBER 1976 – REVISED SEPTEMBER 1999
logic symbol
1A
1B
2A
2B
†
This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC publication 617-12.
Pin numbers shown are for the D, JG, and P packages.
†
1
2
6
7
FUNCTION TABLE
(each driver)
A
L L L (on state)
L H L (on state)
H L L (on state)
H H H (off state)
positive logic:
Y = AB or A
&
B Y
+B
3
1Y
5
2Y
logic diagram (positive logic)
1
1A
2
1B
6
2A
7
2B
schematic (each driver)
4 kΩ 1.6 kΩ 130 Ω
A
B
1 kΩ
Resistor values shown are nominal.
500 Ω
electrical characteristics over recommended operating free-air temperature range
SN55451B SN75451B
MIN TYP§MAX MIN TYP§MAX
V
I
I
I
I
I
‡
§
Input clamp voltage VCC = MIN, II = –12 mA –1.2 –1.5 –1.2 –1.5 V
IK
VCC = MIN, VIL = 0.8 V,
p
p
Input current at maximum input voltage VCC = MAX, VI = 5.5 V 1 1 mA
I
High-level input current VCC = MAX, VI = 2.4 V 40 40 µA
IH
Low-level input current VCC = MAX, VI = 0.4 V –1 –1.6 –1 –1.6 mA
IL
Supply current, outputs high VCC = MAX, VI = 5 V 7 11 7 11 mA
CCH
Supply current, outputs low VCC = MAX, VI = 0 52 65 52 65 mA
CCL
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
All typical values are at VCC = 5 V, TA = 25°C.
IOL = 100 mA
VCC = MIN, VIL = 0.8 V,
IOL = 300 mA
VCC = MIN, VIH = MIN,
VOH = 30 V
3
1Y
5
2Y
4
GND
V
CC
Y
GND
switching characteristics, VCC = 5 V, TA = 25°C
t
Propagation delay time, low-to-high-level output 18 25
PLH
t
Propagation delay time, high-to-low-level output
PHL
t
Transition time, low-to-high-level output
TLH
t
Transition time, high-to-low-level output 7 12
THL
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IO ≈ 200 mA, CL = 15 pF,
RL = 50 Ω,LSee Figure 1
p
SN55451B
SN75451B
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
V
= 20 V, I
See Figure 2
≈ 300 mA,
VS–6.5
18 25
5 8
VS–6.5
3
Loading...