AC Types Feature 1.5-V to 5.5-V Operation
and Balanced Noise Immunity at 30% of the
Supply Voltage
D
Speed of Bipolar F, AS, and S, With
Significantly Reduced Power Consumption
D
Balanced Propagation Delays
D
±24-mA Output Drive Current
– Fanout to 15 F Devices
D
SCR-Latchup-Resistant CMOS Process and
Circuit Design
D
Exceeds 2-kV ESD Protection Per
CD54AC05 ...F PACKAGE
CD74AC05 ...E OR M PACKAGE
1A
1Y
2A
2Y
3A
3Y
GND
(TOP VIEW)
1
14
2
13
3
12
4
11
5
10
6
7
9
8
V
6A
6Y
5A
5Y
4A
4Y
CC
MIL-STD-883, Method 3015
description
The ’AC05 devices contain six independent inverters. These devices perform the Boolean function Y = A. The
open-drain outputs require pullup resistors to perform correctly, and can be connected to other open-drain
outputs to implement active-low wired-OR or active-high wired-AND functions.
ORDERING INFORMA TION
T
A
–
†
Package drawings, standard packing quantities, thermal data, symbolization, and PCB
design guidelines are available at www.ti.com/sc/package.
PACKAGE
PDIP – ETubeCD74AC05ECD74AC05E
–
CDIP – FTubeCD54AC05F3ACD54AC05F3A
†
TubeCD74AC05M
Tape and reelCD74AC05M96
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
FUNCTION TABLE
INPUT
logic diagram, each inverter (positive logic)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
(each inverter)
OUTPUT
A
HL
LZ
Y
YA
Copyright 2002, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
1
CD54AC05, CD74AC05
∆t/∆v
Input transition rise or fall rate
ns/V
HEX INVERTERS
WITH OPEN-DRAIN OUTPUTS
SCHS306C – JANUARY 2001 –REVISED JUNE 2002
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
Input clamp current, I
Output clamp current, I
Continuous output current, I
Continuous current through V
Package thermal impedance, θ
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
VCC = 1.5 V to 3 V505050
VCC = 3.6 V to 5.5 V202020
–40°C TO
85°C
0.90.90.9
CC
0V
CC
–55°C TO
125°C
0V
CC
UNIT
V
V
V
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
CC
(INPUT)
(OUTPUT)
A
Y
ns
(INPUT)
(OUTPUT)
A
Y
ns
(INPUT)
(OUTPUT)
A
Y
ns
CD54AC05, CD74AC05
HEX INVERTERS
WITH OPEN-DRAIN OUTPUTS
SCHS306C – JANUARY 2001 –REVISED JUNE 2002
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETERTEST CONDITIONSV
1.5 V0.10.10.1
IOL = 50 µA
V
OL
I
I
I
CC
C
†
T est one output at a time, not exceeding 1-second duration. Measurement is made by forcing indicated current and measuring voltage to minimize
power dissipation. T est verifies a minimum 50-Ω transmission-line drive capability at 85°C and 75-Ω transmission-line drive capability at 125°C.
i
VI = VIH or V
VI = VCC or GND5.5 V±0.1±1±1µA
VI = VCC or GND,IO = 05.5 V44080µA
IL
IOL = 12 mA3 V0.360.440.5
IOL = 24 mA4.5 V0.360.440.5
IOL = 50 mA
IOL = 75 mA
†
†
3 V0.10.10.1
4.5 V0.10.10.1
5.5 V1.65
5.5 V1.65
TA = 25°C
MINMAXMINMAXMINMAX
–40°C TO
85°C
101010pF
–55°C TO
125°C
UNIT
V
switching characteristics over recommended operating free-air temperature range,
switching characteristics over recommended operating free-air temperature range,
V
= 3.3 V ± 0.3 V, CL = 50 pF (unless otherwise noted) (see Figure 1)
CC
PARAMETER
t
PLZ
t
PZL
FROM
TO
–40°C TO
85°C
MINMAXMINMAX
310.42.911.5
2.38.32.39.1
–55°C TO
125°C
switching characteristics over recommended operating free-air temperature range,
= 5 V ± 0.5 V, CL = 50 pF (unless otherwise noted) (see Figure 1)
V
CC
PARAMETER
t
PLZ
t
PZL
FROM
TO
–40°C TO
85°C
MINMAXMINMAX
2.27.52.18.2
1.75.91.66.5
–55°C TO
125°C
UNIT
UNIT
UNIT
operating characteristics, VCC = 5 V, TA = 25°C
C
Power dissipation capacitance
pd
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETERTYPUNIT
105
pF
3
CD54AC05, CD74AC05
HEX INVERTERS
WITH OPEN-DRAIN OUTPUTS
SCHS306C – JANUARY 2001 –REVISED JUNE 2002
PARAMETER MEASUREMENT INFORMATION
From Output
Under Test
CL = 50 pF
(see Note A)
†
When VCC = 1.5 V, R1 = R2 = 1 kΩ
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns.
C. The outputs are measured one at a time with one input transition per measurement.
R1 = 500 Ω
R2 = 500 Ω
LOAD CIRCUIT
Figure 1. Load Circuit and Voltage Waveforms
†
†
S1
2 × V
CC
Input
Output
50% V
CC
t
PZL
50% V
CC
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
50% V
CC
t
PLZ
20% V
V
0 V
≈V
CC
V
CC
CC
OL
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty . Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty . Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. T o minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party , or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.