EN
BOOST
SW
FB
GND
V
OUT
L1
R1
R2
D1
D2
D3
R3
C1
R5
R4
GND GND
C4
C3
C2
V
IN
V
IN
V
EN
1 Introduction
The LM2736 demo board is configured to convert 5V input to 1.5V output at 750 mA load current using
the LM2736X 1.6 MHz or the LM2736Y 550 kHz step down DC-DC regulator. The tiny low profile thin
SOT23 package allows the demo board to be manufactured using less than 1 square inch of a 4-layer
printed circuit board.
The circuit is configured with the boost diode connected to VIN, and according to the datasheet, VINmust
not exceed the maximum operating limit of 5.5V + V
voltage between the Boost and SW pins, V
more information regarding this requirement, see the LM2736 Thin SOT 750mA Load Step-Down DC-DC
Regulator Data Sheet (SNVS316).
A bill of materials below describes the parts used on this demo board. A schematic and layout have also
been included below along with measured performance characteristics. The schematics at the end of this
document show how to re-configure this demo board for various input and output conditions as discussed
in the LM2736 datasheet. Short or leave open the indicated connection as indicated in the schematics.
The above restrictions for the input voltage are valid only for the demo board as shipped with the demo
board schematic below.
User's Guide
SNVA135A–October 2005–Revised April 2013
AN-1418 LM2736 Evaluation Board
using this configuration. This will ensure that the
fD2
- VSW, does not exceed 5.5V for proper operation. For
BOOST
2 Operating Conditions
VIN= 5V
VO= 1.5V
IO= 750 mA
All trademarks are the property of their respective owners.
SNVA135A–October 2005–Revised April 2013 AN-1418 LM2736 Evaluation Board
Submit Documentation Feedback
Figure 1. LM2736 Demo Board Schematic
Copyright © 2005–2013, Texas Instruments Incorporated
1
Operating Conditions
Figure 2. Efficiency vs Load Current
Table 1. Bill of Materials (BOM) X-Version
Part ID Part Value Manufacturer Part Number Package Type
C1, Input Cap 4.7 µF, 10V, X5R Murata GRM42-6X5R475K10 1206
C2, Output Cap 10 µF, 6.3V, X5R Murata GRM42-6X5R106K6.3 1206
C3, Boost Cap 0.01 µF Vishay VJ1206Y103KXXA 1206
D2, Boost Diode 1Vf@ 50 mA Diode Diodes, Inc. 1N4148W SOD-123
R2 10 kΩ, 1% Vishay CRCW12061002F 1206
U1 750 mA Buck Regulator Texas Instruments LM2736 Thin SOT23-6
D1, Catch Diode 0.34VfSchottky 1A, 20V
L1 4.7 µH, 1.6A, 28 mΩ TDK SLF6028T-4R7M1R6 6028
R1 2 kΩ, 1% Vishay CRCW12062001F 1206
R3 0Ω Vishay CRCW12060000F 1206
R5 50 kΩ, 1% Vishay CRCW08055002F 0805
D3, C4, R4 Open
International Rectifier MBRA120 SMA
R
www.ti.com
Part ID Part Value Manufacturer Part Number Package Type
C1, Input Cap 10 µF, 10V, X5R Murata GRM42-6X5R106K10 1206
C2, Output Cap 10 µF, 6.3V, X5R Murata GRM42-6X5R106K6.3 1206
C3, Boost Cap 0.01 µF Vishay VJ1206Y103KXXA 1206
D2, Boost Diode 1Vf@ 50 mA Diode Diodes, Inc. 1N4148W SOD-123
R2 10 kΩ, 1% Vishay CRCW12061002F 1206
U1 750 mA Buck Regulator Texas Instruments LM2736 Thin SOT23-6
D1, Catch Diode 0.34VfSchottky 1A, 20V
L1 10 µH, 1.3A, 53 mΩ TDK SLF6028T-100M1R3 6028
R1 2 kΩ, 1% Vishay CRCW12062001F 1206
R3 0Ω Vishay CRCW12060000F 1206
R5 50 kΩ, 1% Vishay CRCW08055002F 0805
D3, C4, R4 Open
2
AN-1418 LM2736 Evaluation Board SNVA135A–October 2005–Revised April 2013
Table 2. Bill of Materials (BOM) Y-Version
R
Copyright © 2005–2013, Texas Instruments Incorporated
International Rectifier MBRA120 SMA
Submit Documentation Feedback
www.ti.com
3 PCB Layout
PCB Layout
SNVA135A–October 2005–Revised April 2013 AN-1418 LM2736 Evaluation Board
Submit Documentation Feedback
Figure 3. Top Layer
3
Copyright © 2005–2013, Texas Instruments Incorporated
PCB Layout
www.ti.com
4
AN-1418 LM2736 Evaluation Board SNVA135A–October 2005–Revised April 2013
Figure 4. Internal Plane 1 (GND)
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
www.ti.com
PCB Layout
SNVA135A–October 2005–Revised April 2013 AN-1418 LM2736 Evaluation Board
Submit Documentation Feedback
Figure 5. Internal Plane 2 (VIN)
5
Copyright © 2005–2013, Texas Instruments Incorporated
PCB Layout
www.ti.com
6
AN-1418 LM2736 Evaluation Board SNVA135A–October 2005–Revised April 2013
Figure 6. Bottom Layer
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
VIN
VIN
EN
BOOST
SW
FB
GND
V
OUT
C3
L1
C2
R1
R2
D1
D2
D3
C4
R3
C1
R5
R4
VEN
GND GND
V
IN
V
IN
EN
BOOST
SW
FB
GND
V
OUT
C3
L1
C2
R1
R2
D1
D2
D3
C4
R3
C1
R5
R4
V
EN
GND GND
www.ti.com
4 Additional Circuit Configuration Schematics
Additional Circuit Configuration Schematics
Figure 7. V
Figure 8. V
Derived From V
BOOST
Derived From V
BOOST
OUT
SHUNT
SNVA135A–October 2005–Revised April 2013 AN-1418 LM2736 Evaluation Board
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
7
VIN
V
IN
EN
BOOST
SW
FB
GND
V
OUT
C3
L1
C2
R1
R2
D1
D2
D3
C4
R3
C1
R5
R4
VEN
GND GND
V
IN
VIN
EN
BOOST
SW
FB
GND
V
OUT
C3
L1
C2
R1
R2
D1
D2
D3
C4
R3
C1
R5
R4
VEN
GND GND
Additional Circuit Configuration Schematics
www.ti.com
Figure 9. V
Figure 10. V
Derived From Series Zener Diode (VIN)
BOOST
Derived From Series Zener Diode (V
BOOST
OUT
)
8
AN-1418 LM2736 Evaluation Board SNVA135A–October 2005–Revised April 2013
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Loading...