Teufel Subconnect RX Technical Description And Instruction Manual

Page 1
Technical Description and Instruction Manual
Subwoofer Signal Receiver
Subconnect RX
93080_GB_20150610.indd 193080_GB_20150610.indd 1 11.06.15 08:3411.06.15 08:34
Page 2
2 • Receiver Subconnect RX
Contents
Notice .............................................. 3
Original packaging .......................... 3
Complaints ...................................... 3
Contact ............................................ 3
For Your Safety ...................................4
Proper use ....................................... 4
Explanation of terms ....................... 4
Safety notes .................................... 4
Explanation of symbols................... 5
Overview .............................................6
Product contents ............................. 6
Checking the product contents ...... 6
Operational controls and
connections ..................................... 6
Setup/Wall Mounting ........................7
Setup location ................................. 7
Wall mounting ................................. 7
Connecting .........................................8
Operation ............................................8
Manual connection ......................... 8
Automatic connection ..................... 9
Automatic activation/deactivation
.. 9
Cleaning & Maintenance ............... 10
Troubleshooting .............................. 11
Declaration of Conformity .............. 12
Technical Data ................................ 13
93080_GB_20150610.indd 293080_GB_20150610.indd 2 11.06.15 08:3411.06.15 08:34
Page 3
3 • Receiver Subconnect RX
General Notes and Information
Notice
The information in this document may change without prior notice and in no way constitutes any liability on the part of Lautsprecher Teufel GmbH.
No part of this instruction manual may be reproduced in any form or be broad­casted in any way electronically, me­chanically, by photocopy or recording without the written permission of Laut­sprecher Teufel GmbH.
© Lautsprecher Teufel GmbH Version 1.0 June 2015
Original packaging
If you wish to exercise your eight-week right of return, we ask that you be abso­lutely sure to hold on to the packaging. We can only accept the return of the speakers WITH THE ORIGINAL PACKAG­ING.
Empty boxes are not available!
Complaints
If you would like to file a complaint, we will need the following information to process your inquiry:
1. Invoice number
Can be found on the sales slip (en­closed with the product) or on the order confirmation received as a PDF document, e.g. 4322543
2. Serial number or batch number
Located on the back of the device, e.g. serial no.: KB20240129A-123.
Thank-you for your support!
Contact
Please contact our customer service with any questions, suggestions or comments:
Lautsprecher Teufel GmbH
BIKINI Berlin
Budapester Strasse 44
10787 Berlin (Germany)
Phone 00800 - 200 300 40 (toll-free)
Fax +49 (0)30 / 300 930 930
E-mail: service@teufelaudio.com
www.teufelaudio.com
Before operating the devices, please first read the safety
notes and instruction manual carefully. Only in this way, can you ensure that all functions are used in a safe and reliable manner. Store the instruction manual in a safe place and also be sure to pass it on to any subsequent owner.
93080_GB_20150610.indd 393080_GB_20150610.indd 3 11.06.15 08:3411.06.15 08:34
Page 4
4 • Receiver Subconnect RX
For Your Safety
Proper use
The Subconnect RX is intended for receiving a mono subwoofer signal and for transmitting it to the subwoofer via an RCA cable. The Subconnect TX or another compatible device from our assortment can be used as a trans­mitter.
Only use the Subconnect RX as described in this instruction manual. Any other use will be deemed as not in accordance with the instructions and may lead to damage of property or even persons.
The manufacturer accepts no liability for damage caused by improper use.
The Subconnect RX is intended for private use.
Explanation of terms
You can find the following signal terms in these instructions:
WARNING
This signal term indicates a moderate risk, which, if not avoided, may result in death or severe injury.
CAUTION
This signal term indicates a low risk, which, if not avoided, may result in minor or moderate injury.
NOTICE
This signal term warns you of potential damage.
Safety notes
This chapter contains general safe­ty notes which you should always observe to protect yourself and third parties. Also observe the warning notes in each chapter of this instruc­tion manual.
Improper electrical installation or excessive mains voltage may result in an electrical shock.
• The enclosed mains adapter is suita­ble for a mains voltage of 100 – 240 V ~ 50/60 Hz. When connecting the device, make sure that the correct voltage is present.
• Only use the enclosed mains adapter or a mains adapter with an identical construction.
• Check the mains adapter regularly for damage. Do not in any case use a damaged mains adapter.
• Never open the housing of the mains adapter.
• Only use the device indoors and not in wet rooms. Protect it from drip­ping and splashing water. Make sure that no vases or other liquid-filled containers are located on or near the device in order to prevent liquid from penetrating the housing. If wa-
93080_GB_20150610.indd 493080_GB_20150610.indd 4 11.06.15 08:3411.06.15 08:34
Page 5
5 • Receiver Subconnect RX
ter or other debris has infiltrated the device, immediately pull the mains adapter out of the socket.
• This Subconnect RX is disconnected from the mains by pulling the mains adapter. Therefore, make sure that the mains adapter is always easily accessible.
• Never modify the Subconnect RX. Unauthorised interventions may affect the safety and functionality.
• Let an authorised specialist work­shop perform repairs. Only parts that comply with the original device data may be used for repairs.
• Never touch the mains adapters with wet hands.
An unsuitable location may result in accidents or damage to property.
• Do not expose the Subconnect RX to direct sunlight and do not set it up near heat sources (e.g. heaters, ovens, other heat generating equip­ment such as amplifiers etc.).
• Do not use the Subconnect RX in en­vironments with a risk of explosion and only in locations where wireless transmission is permitted.
Children can become trapped in the packing film when playing and suffocate.
• Do not allow children to play with the device or the packing film.
Explanation of symbols
Protection class II Dual insulation
May only be used indoors
Polarity on the round con­nector: outside (–), inside (+)
Old devices must not be disposed of with house­hold waste!
If the device is no longer oper­ational, every consumer is required by law to dispose of old devices separate­ly from household waste, e.g. at a col­lection point run by the communal au­thority/borough. This ensures that old devices are recycled in a professional manner and also rules out negative consequences for the environment.
For this reason, electrical equipment is marked with the adjacent symbol.
93080_GB_20150610.indd 593080_GB_20150610.indd 5 11.06.15 08:3411.06.15 08:34
Page 6
6 • Receiver Subconnect RX
Overview
Product contents
1 x Subconnect RX 1 x mains adapter 1× RCA cable
Checking the product contents
• Check that all items have been deliv­ered and that nothing is damaged.
• If the delivery is incomplete or has transport damages, please contact our service team (see page 3).
• Do not in any case operate the device if it is damaged.
Operational controls and connections
1 Jack for mains adapter
2 RCA output jack
3 Pairing button (connect to the
transmitter)
LED status indicators
1 2 3
456
Status LED 4 LED 5 LED 6
Standby off off red
Activation process off green off
Connected blue (continuous) green off
Searching for stations blue (flashes slowly) green off
Pairing mode (button (3) depressed) blue (flashes quickly) green off
93080_GB_20150610.indd 693080_GB_20150610.indd 6 11.06.15 08:3411.06.15 08:34
Page 7
7 • Receiver Subconnect RX
Setup/Wall Mounting
Setup location
NOTICE
If the device is subjected to warm temperatures after being cold (e.g. after transport), con­densation may occur inside of it.
– In this case, wait at least 2
hours before
you connect and
activate it.
CAUTION
– This Subconnect RX is dis-
connected from the mains by pulling the mains adapter. Therefore, make sure that the mains adapter is always easily accessible.
• Select a stable, level base. In case of wall mounting, follow the instructions in the next chapter.
• Make sure that the environment is clean and free from dust.
• Select a location away from heat sources and direct sunlight.
• Lay the connector cables so that they do not pose a tripping hazard.
• Do not place any heavy objects on the cables or the device.
Wall mounting
For wall installation, 2 keyhole open­ings are located on the bottom of the Subconnect RX that can be used to hang it on 2 screws.
CAUTION
– Make sure that there are no
cables or pipes in the wall where you intend to mount the device. Before you drill holes for the dowels, use a metal detector to check the applicable areas. Otherwise, there is a risk of electric shock/short circuit!
93080_GB_20150610.indd 793080_GB_20150610.indd 7 11.06.15 08:3411.06.15 08:34
Page 8
8 • Receiver Subconnect RX
Connecting
Operation
1. Connect the jack (2) with the input
jack of your subwoofer via a mono RCA cable.
2. Insert the round connector of the
mains adapter into the jack (1).
3. Plug the mains adapter into an easi­ly accessible mains socket.
1 2
Manual connection
1. Push the pairing button (3) until the LED (4) quickly blinks in blue.
2. Put the associated transmitter also into paring mode. For more informa­tion, please refer to the transmitter’s instruction manual.
• As soon as the Subconnect RX finds a compatible transmitter, it will connect with it. The LED (4) will illuminate continu- ously in blue.
3
4
93080_GB_20150610.indd 893080_GB_20150610.indd 8 11.06.15 08:3411.06.15 08:34
Page 9
9 • Receiver Subconnect RX
Automatic connection
• If the Subconnect RX was already connected with a compatible trans­mitter, a connection with it will be established immediately. The LED (4) will illuminate continu- ously in blue.
• If there is no transmitter nearby or if it is switched off, the Subconnect RX will look for a transmitter. The LED (4) will slowly blink in blue.
• The connection will be established as soon as you switch on the trans­mitter. The LED (4) will illuminate continu- ously in blue.
Automatic activation/ deactivation
• As soon as the Subconnect RX receives a signal from a connected transmitter, it will switch back on from standby mode.
• If the signal is deactivated, the Subconnect RX will switch back to standby mode after a short time.
4
93080_GB_20150610.indd 993080_GB_20150610.indd 9 11.06.15 08:3411.06.15 08:34
Page 10
10 • Receiver Subconnect RX
Cleaning & Maintenance
CAUTION
– Pull the mains adapter out of
the socket before you clean it.
NOTICE
Using the wrong cleaning agents may damage the housing.
– Do not use caustic cleaning
products, rubbing alcohol, thinners, petrol or similar un­der any circumstances. Such cleaning agents may damage the surface of the housing.
• Ideally, you should remove dust or small amounts of dirt with a dry, smooth cloth.
• Rub off stubborn dirt with a damp cloth. Make sure that no liquid pene­trates the housing.
• Then immediately wipe the surfaces dry with a soft cloth.
93080_GB_20150610.indd 1093080_GB_20150610.indd 10 11.06.15 08:3411.06.15 08:34
Page 11
11 • Receiver Subconnect RX
Troubleshooting
The following advice should help you to solve problems. If this does not help, you will find useful information in the detailed FAQs on our website. Otherwise, please contact our hotline (see page 3). Take note of the warranty instructions.
Problem Possible cause Solution
No function. The Subconnect RX
has “hung up”.
Pull the mains adapter out of the socket and insert it back in the socket after approx. 10 seconds.
No connection is established.
The transmitter has not been switched on.
Switch the transmitter on.
Distance is too great or objects are block­ing the connection signal.
Correct the location of the devices.
The connection is not automatically estab­lished.
Push the pairing button (3).
93080_GB_20150610.indd 1193080_GB_20150610.indd 11 11.06.15 08:3411.06.15 08:34
Page 12
12 • Receiver Subconnect RX
2015
EG-Konformitätserklärung
EU-Declaration of Conformity
Hiermit bestätigen wir, dass das nachfolgend bezeichnete Gerät den angegebenen-Richtlinien entspricht.
We herewith confirm that the appliance as detailed below complies with the mentioned directives.
Artikelbezeichnung:
Article description:
Subconnect RX
Firmenanschrift:
Company address
Teufel Lautsprecher GmbH Budapester Straße 44 D-10787 Berlin
Einschlägige EG-Richtlinien / Governing EU-directives / Directives CE concernées :
1. Elektromagnetische Verträglichkeit (EMV) Electromagnetic compatibility (EMC) 2004/108/EC
2. Niederspannungs-Richtlinie
Low-voltage directive
2006/95/EC
3. Sicherheit von Spielzeug Safety of toys 88/378/EEC, amended 93/68/EEC
4. Medizinprodukte (Klasse 1) Medical device directive (Class 1) 93/42/EEC
5. Funkanlagen und
Telekommunikationsendeinrichtungen Radio and Telecommunication Terminal Equipment
R&TTE 1999/5/EC
6. Ökodesign – Richtlinie Energy – Using – Product – Directive (EuP) 2009/125/EEC
7. Richtlinie zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten (Rohs- Richtline 2011/65/EC)
Harmonisierte EN-Normen /
Harmonised EN-Standards
Der Artikel entspricht folgenden, zur Erlangung des CE-Zeichens erforderlichen Normen:
The article complies with the standards as mentioned below which are necessary to obtain the CE-symbol:
DIN EN 55013:2013 DIN EN 55020:2012 DIN EN 61000-3-2:2010 DIN EN 61000-3-3:2014 DIN EN 60950-1:2006 A1:2010 A2:2013 A11:2009 A12:2011 ETSI EN 301489-1 V1.9.2 ETSI EN 301489-9 V1.4.1 ETSI EN 300328 V 1.8.1: Verordnung 1275/2008 Verordnung 0278/2009
Edgar van Velzen
Geschäftsführer
Ausstellungsdatum / Date of issue:
16. März 2015
93080_GB_20150610.indd 1293080_GB_20150610.indd 12 11.06.15 08:3411.06.15 08:34
Page 13
13 • Receiver Subconnect RX
Subconnect RX
Dimensions (WxHxD) 110 x 28 x 90 mm
Weight 120 g
Operating voltage 12 V DC
Mains adapter
Input voltage 100 – 240 V~ 50/60 Hz
Output voltage 12 V DC/830 mA
Technical Data
You can find further technical data on our website. Technical changes reserved!
93080_GB_20150610.indd 1393080_GB_20150610.indd 13 11.06.15 08:3411.06.15 08:34
Page 14
14 • Receiver Subconnect RX
93080_GB_20150610.indd 1493080_GB_20150610.indd 14 11.06.15 08:3411.06.15 08:34
Page 15
15 • Receiver Subconnect RX
93080_GB_20150610.indd 1593080_GB_20150610.indd 15 11.06.15 08:3411.06.15 08:34
Page 16
Instruction No. HCHAM / 93080_GB_20150610
Please contact our customer service with any questions, suggestions or comments:
Lautsprecher Teufel GmbH
BIKINI Berlin
Budapester Strasse 44
10787 Berlin (Germany)
Phone: 00800 - 200 300 40 (toll-free)
Fax: +49 (0)30 - 300 930 930
www.teufelaudio.com
No responsibility is assumed for the correctness of this information.
Technical changes, typographical errors and other errors reserved.
93080_GB_20150610.indd 1693080_GB_20150610.indd 16 11.06.15 08:3411.06.15 08:34
Loading...