Page 1
Technical Description And User Manual
S 6000 SW THX® Select
Active subwoofer with THX® select certificate and
wireless technology
Page 2
Contents
General Notes And Information ...........................3
Notice ..................................................................3
Trademarks ........................................................3
Original packaging ..............................................3
Complaints ..........................................................3
Contact ................................................................3
Proper use ...........................................................3
For Your Safety .....................................................4
Signal terms ........................................................4
Safety notes ........................................................4
Warning of damage to property ..........................5
Explanation of symbols ........................................6
Overview ...............................................................6
Unpacking ...........................................................6
Package contents ...............................................6
Optional accessories ..................................6
Checking the package contents ........................6
Operational Controls And Connections ...............7
Back side .............................................................7
Setup/Mounting ...................................................8
Setup location .....................................................8
Location tips ................................................8
Protective cover ..................................................8
Optional metal grid......................................9
Connecting ......................................................... 10
Audio connection ............................................. 10
Connection via SUB IN ............................. 10
Wireless connection ................................ 10
Mains connection ............................................ 10
Use And Settings ............................................... 11
Activating and deactivating ............................. 11
Automatic activation/deactivation ......... 11
Establishing a wireless connection ................ 11
Adjusting the volume ....................................... 12
Confi guring the sound pattern ........................ 12
Adjusting the amplifi er and subwoofer ........... 12
Amplifi er settings ..................................... 12
Subwoofer settings .................................. 12
Care And Cleaning ............................................. 13
Troubleshooting ................................................. 14
Technical Data ................................................... 15
Declaration of Conformity ................................. 15
2 • S 6000 SW THX® Select
Page 3
General Notes And Information
Notice
The information in this document may change
without prior notice and in no way constitutes any
liability on the part of Lautsprecher Teufel GmbH.
No part of this user manual may be reproduced in
any form or be broadcasted in any way electronically,
mechanically, by photocopy or recording without the
written permission of Lautsprecher Teufel GmbH.
© Lautsprecher Teufel GmbH
Version 1.0
January 2018
Trademarks
® All trademarks are the property of their respective
owners.
THX SELECT and the THX logo
are trademarks of THX Ltd.,
which are registered in some
jurisdictions. All rights reserved.
Contact
Please contact our customer service department
with any questions, suggestions, or complaints:
Lautsprecher Teufel GmbH
BIKINI Berlin
Budapester Str. 44
10787 Berlin (Germany)
Phone 00800 200 300 40 (toll-free)
Fax +4930 / 300 930 930
www.teufelaudio.co.uk/contact.html
Proper use
The active subwoofer is designed for the playback of
music and speech from an external player.
Only use the subwoofer as described in this user
manual. Any other use will be deemed as not in
accordance with the instructions and may lead to
damage of property or even persons.
The manufacturer accepts no liability for damage
caused by improper use.
The subwoofer is intended for private use.
Original packaging
If you wish to exercise your eight-week right of
return, we ask that you be absolutely sure to hold
onto the packaging. We can only accept the return of
the speakers WITH THE ORIGINAL PACKAGING.
Empty boxes are not available!
Complaints
In case of a complaint we will need the following
information to process your enquiry:
1. Invoice number
Can be found on the sales slip (enclosed with the
product) or on the order confirmation received as a
PDF document, e.g. 4322543
2. Serial number or batch number
Located on the back side of the device, e.g. serial
no.: KB20240129A-123.
Thank you for your support!
Before operating the subwoofer for the first
time, please read the safety notes and user
manual carefully. This is the only way to
use all functions safely and reliably. Store the user
manual in a safe place and also be sure to pass it on
to any subsequent owner.
NOTICE
Check that all items have been delivered
and that nothing is damaged. If you find
any damage, do not operate the device;
instead contact our customer service
department.
3 • S 6000 SW THX® Select
Page 4
For Your Safety
Signal terms
You can find the following signal terms in this user
manual:
WARNING
This signal term indicates a moderate
risk, which, if not avoided, may result in
death or severe injury.
CAUTION
This signal term indicates a low risk,
which, if not avoided, may result in minor
or moderate injury.
NOTICE
This signal term warns you of potential
damage.
Safety notes
This chapter contains general safety notes which
you should always observe to protect yourself and
third parties. Also observe the warning notes in each
chapter of this user manual.
Improper electrical installation or excessive
mains voltage may result in an electrical shock.
– The device is suitable for a mains voltage of
230 V ~ / 50 Hz. When connecting the device,
make sure that the correct voltage is present. You
can find more information about this on the rating
plate.
– Check the device regularly for damage.
Immediately disconnect the mains plug and do
not operate the device if its housing or mains cord
is defective or exhibits other visible damages.
– If the mains cord of the device is damaged,
replace it with an equivalent original mains cord.
– This device can only be completely disconnected
from the grid by pulling the mains plug. Thus,
make sure that the mains plug is always easily
accessible.
– If the device emits smoke, smells burnt or
produces unusual sounds, immediately disconnect it from the mains and do not operate it
further.
– Never open the device housing.
Repairs may only be carried out by an authorised
specialist workshop. Only parts that match the
original specifications may be used.
– Only use the accessory products specified by the
manufacturer.
– Only use the device indoors.
– Do not operate the device in wet rooms and
protect it from dripping and splashing water.
Make sure that no vases or other liquid-filled
objects are located on or near the device in order
to prevent liquid from penetrating the housing.
If water or other debris ends up penetrating the
housing, immediately pull the mains plug and, if
applicable, take out any batteries. Then send the
device to our service address.
– Never modify the device. Unauthorised modifica-
tions may affect the safety and functionality.
– Never touch the mains plug with wet hands.
An unsuitable setup location may result in injury
and damage.
– If the subwoofer is not securely mounted, do
not use it in vehicles, in unstable locations, on
wobbly tripods or furniture, on underdimensioned
brackets etc. The speaker may tip or fall over and
cause injury to persons or be damaged itself.
– Place the subwoofer in such a way that it cannot
be knocked over inadvertently and make sure that
the cables do not pose a tripping hazard.
– Do not place the subwoofer near heat sources
(e.g. heaters, ovens, other heat generating equipment such as amplifiers etc.).
– Do not use the device in environments where
there is a risk of explosion.
– Only use the subwoofer without any cables in
locations where wireless radio transmission is
allowed.
An unstable base may cause the unit to tip and
injure or even kill persons, children are particularly at risk. You can prevent a large number of
accidents by taking the following precautions:
– Only place the subwoofer on the floor.
– If you want to use underframes or speaker stands,
only use those recommended by the manufacturer.
– When storing the product, also ensure that it
stands safely and that it cannot be knocked down
or over.
4 • S 6000 SW THX® Select
Page 5
Children can become trapped in the plastic wrapping when playing and suffocate.
– Do not allow children to play with the device or the
plastic wrapping. There is a danger of suffocation.
– Ensure that children do not remove small parts
from the device or take them off of the device
(e.g. control knobs or plug adapters). They could
swallow the parts and choke.
– Never allow children to operate electrical equip-
ment unsupervised.
Warning of damage to property
NOTICE
If the device is subjected to warm temperatures after being cold (e.g. after transport), condensation may occur inside of it.
– In this case, wait at least 2 hours before
you connect and activate it.
Improper use may lead to damage or fire.
CAUTION
Extended listening at high
volumes may lead to hearing loss.
– To avoid damage to health, avoid
extended listening at high volumes.
– When the volume is set high, always
keep a certain distance from the device
and never place your ear directly on the
speaker.
– If the AV receiver is set to full volume, it
may produce very high sound pressure.
This may have psychic consequences
and also cause physical injury. Children
and pets are particularly at risk. Set your
signal source device volume control to a
low setting before turning on the power.
CAUTION
This product contains magnetic
material.
– Do not place open flames such as
burning candles or similar on the device.
– Ensure sufficient ventilation.
– Do not place the device in direct sunlight.
– Only use the device indoors.
– Do not operate the device in wet
rooms and protect it from dripping and
splashing water. Make sure that no vases
or other liquid-filled objects are located
on or near the device in order to prevent
liquid from penetrating the housing.
The isolation pads can produce discolouration on sensitive surfaces.
– On parquet, varnished wood and similar
surfaces, you should stick felt gliders to
the rubber feet of the speakers or put
blankets or small carpets under them.
This will prevent discolouration of the
floor over the long term.
– Keep magnetically sensitive objects
(e.g. credit cards etc.) away from the
speakers.
– If necessary, consult your physician and
ask for effects on implants such as pacemakers or defibrillators.
5 • S 6000 SW THX® Select
Page 6
Explanation of symbols
Protection class II
Dual insulation
Risk of electrical shock – do not open the
housing.
Disconnect the mains cord before
changing a fuse.
Delayed action 2 ampere fuse, low
breaking capacity, 250 volts
Overview
Unpacking
• Carefully open the box, take out the EPE foam
half-shell and carefully lift the speaker out of the
box.
Old devices must not be disposed of
with household waste!
If the device is no longer operational,
every consumer is required by law to
dispose of old devices separately from
household waste, e.g. at a collection point
run by the communal authority/borough.
This ensures that old devices are recycled in a professional manner and also
rules out negative consequences for the
environment.
For this reason, electrical equipment is
marked with the adjacent symbol.
Package contents
① 1× subwoofer with protective cover
② 1x mains cord for the subwoofer
③ Protective metal grid with screws and pivots
Optional accessories
④ Subconnect receiver module
⑤ Subconnect transmitter
Checking the package contents
• Check that all items have been delivered and that
nothing is damaged.
• If the delivery is incomplete or exhibits transport
damages, please contact our service team (see
page 3).
• Do not in any case operate the device if it is
damaged.
①
②
③
④
⑤
6 • S 6000 SW THX® Select
Page 7
Back side
13
12
11
10
9
Operational Controls And Connections
1
Desig-
Item
nation
2
3
4
5
6
7
8
1–
2 STATUS
SUB
3
LEVEL
BASS
4
BOOST
5 INPUT
6 PHASE
7O I
8–
9 POWER
10 CLIP
AUTO
11
LEVEL
12 SUB IN
13 PAIRING
14 –
Description
Bay for subconnect receiver
module
Status of the transmission path
Adjust the subwoofer volume
Adjust the bass sound
Switch between wireless/cordless operation
Switch the phase
Turn the device on/off
Mains connection
Automatic activation/deactivation or permanent activation
Lights up in the event of overmodulation
Set the level for automatic activation/deactivation
RCA input jack
Pair the device with a transmitter
Power indicator
14
7 • S 6000 SW THX® Select
Page 8
Setup/Mounting
Setup location
NOTICE
If the device is subjected to warm temperatures after being cold (e.g. after transport), condensation may occur inside of it.
– In this case, wait at least 2 hours before
you connect and activate it.
The isolation pads can produce discolouration on sensitive surfaces.
– On parquet, varnished wood and similar
surfaces, you should stick felt gliders to
the rubber feet of the speakers or put
blankets or small carpets under them.
This will prevent discolouration of the
floor over the long term.
Our website contains comprehensive notes for
correct setup.
You should place the subwoofer on the floor as
close as possible to the television. However, you can
also set it up at another location in the room as the
human ear is unable to localise low tones.
However, do not set it up in the corner of the room
as this may result in uncontrollable frequency rises.
Protective cover
You can take the protective cover off of the
subwoofer by carefully reaching behind the protective cover and slowly pulling it off to the front.
NOTICE
Risk of damage!
– Make sure that you do not touch the
highly sensitive diaphragms.
When putting the protective cover on, please make
sure that the installation pins slide directly into the
corresponding jacks on the subwoofer.
Location tips
• Select a stable, level base.
• Make sure that the environment is clean and free
from dust.
• Select a location away from heat sources and
direct sunlight.
• Lay the connector cords so that they do not pose
a tripping hazard.
• Do not place any heavy objects on the cable or the
devices.
8 • S 6000 SW THX® Select
Page 9
Optional metal grid
A protective metal grid is also included in the
package contents, which you can install instead of
the protective cloth cover.
• You will need a AF5 hexagon key for the assembly:
1. From the front, insert one of the enclosed
hexagon socket screws (a) through one of the
mounting holes (b) in the grid ③.
2. Screw one of the pivots (c) onto the screw.
3. Repeat steps 1 and 2 for the other three mounting
holes.
4. Carefully place the grid on the subwoofer so that
the pivots slide right into the corresponding jacks
(d) on the subwoofer.
③
ab cd
9 • S 6000 SW THX® Select
Page 10
Connecting
Audio connection
You can connect the S 6000 SW THX® Select to
your receiver with the SUB IN jack (12) using an RCA
cable or connect wirelessly via the optional Subconnect receiver module ④.
You can set the audio input of
the subwoofer using the “INPUT”
switch (5):
• “SUB IN” – If you have
connected the subwoofer to the
subwoofer output on your AV
receiver.
• “WIRELESS” – If you have
purchased a Subconnect
receiver module and your AV
receiver supports the wireless connection with
the subwoofer (you can find a list of compatible
devices on www.teufelaudio.com) or you can use
the Subconnect transmitter.
12
5
7
8
1. If applicable, switch your S 6000 SW THX® Select
off with the main power switch (7) (“OFF” position).
1
Connection via SUB IN
Use a mono RCA cable (not included in the package
contents) to connect the “SUB IN” jack (12) to the
AV receiver’s subwoofer output.
Wireless connection
④
If you would like to establish connection between
your amplifier and the S 6000 SW THX® Select, you
can order a Subconnect receiver module ④ and, if
applicable, a corresponding Subconnect transmitter
in our webshop www.teufelaudio.com.
NOTICE
Risk of damage!
– Switch the subwoofer off with the mains
switch (7) before you insert or pull out the
module.
2. Take the protective cap off of the bay (1): For this,
gently push on the protective cap from the top.
3. Insert the Subconnect receiver module ④ in the
bay (1). The module’s plug connector only fits the
bay in one direction. Do not apply force. If necessary, turn the module around.
4. Put the protective cap back on the bay (1).
Mains connection
1. If necessary, ensure that the main power switch
POWER (7) is switched off (“OFF” position).
②
2. Insert the IEC power plug of the mains cord② into
the jack (8).
3. Insert the mains plug in a mains power socket
(230 V ~/50 Hz).
10 • S 6000 SW THX® Select
Page 11
Activating and deactivating
– Use the switch (7) to switch the S 6000 SW THX®
Select
on and off.
The CLIP LED (10) will briefly illuminate in red
during activation.
When switched on, the power indicator (14) will
be illuminated in red.
Automatic activation/deactivation
– You can switch the mode with the POWER switch
(9):
ON The subwoofer is permanently switched on.
AUTO The subwoofer switches itself on as soon
as an audio signal is present. If there’s no
audio signal for approx. 20 minutes, the
subwoofer switches to standby.
– If the auto-function doesn’t switch correctly, you
can use the AUTO LEVEL control (11) to increase
the sensitivity (turn to the right) or decrease it
(turn to the left). You will need a small screwdriver
to do this.
Use And Settings
7
14
11
9
10
Establishing a wireless connection
If you have installed the Subconnect receiver
module for a wireless connection (see „Wireless
connection“ on page 11), you can establish the
connection to your amplifier as follows:
1. If applicable, slide the INPUT switch (5) to the
“WIRELESS” position.
2. Switch your subwoofer and your wireless-compatible amplifier or also the Subconnect transmitter
on.
The STATUS LED (2) will blink slowly and the
devices will now automatically connect. An
existing connection is indicated by the continuously illuminated STATUS LED (2).
Proceed as follows to connect for the first time or
if the devices do not connect automatically or the
connection is interrupted:
1. Hold down the PAIRING button (13) until the
STATUS LED (2) blinks quickly.
2. Then perform the corresponding steps for your
amplifier to establish the connection (for this,
refer to the user manual for your amplifier).
5
13
2
11 • S 6000 SW THX® Select
Page 12
Adjusting the volume
– Use the SUB LEVEL control (3) to adjust the
volume of the subwoofer.
In the “THX®” setting, the
to the specifications of THX® Select.
– If the CLIP LED (10) lights up, the input signal is
too high. In this case, reduce the subwoofer level
on your amplifier.
subwoofer corresponds
Configuring the sound pattern
– Use the BASS BOOST control (4) to set the low
tone sound pattern.
In the “THX®” setting, the
to the specifications of THX® Select.
subwoofer corresponds
Adjusting the amplifier and
subwoofer
Most amplifiers provide a menu with settings for
the speakers (called “Speaker Setup” or similar).
By following our recommendations below, you can
perfectly align the amplifier and the subwoofer:
Amplifier settings
If possible, use your amplifier’s calibration function
so that it automatically adjusts the levels, phase
and run times to the room. If your receiver doesn’t
provide an automatic calibration function, the
following values are recommended:
• Subwoofer to “On”.
• Crossover frequency for subwoofer (cut-off
frequency) to 80–150 Hz depending on the
connected speaker system.
3
10
4
Subwoofer settings
• POWER switch (9) to “AUTO”.
• SUB LEVEL control (3) to “THX®”.
• BASS BOOST control (4) to “THX®”.
• PHASE switch (6) to “0°”.
1. Perform an audio test now and adjust the “SUB
LEVEL” control (3) until the subwoofer can be
“easily heard”. However, it must not drone.
2. If any deep “hits” are too hard or too soft, adjust
the setting of the BASS BOOST control (4) and/or
the PHASE switch (6).
3. Repeat these steps with different video and audio
media.
12 • S 6000 SW THX® Select
Page 13
Care And Cleaning
NOTICE
External influences may damage or
destroy the device.
– If the device is to be left unattended for
a prolonged period of time (e.g. during a
vacation) or if a thunderstorm is forecast,
pull the mains plug out of the socket.
Otherwise, sudden overvoltage could
cause the device to become defective.
– If possible, only use plain water without
any additives. In case of stubborn marks,
a mild soap solution may be used.
– Do not use caustic cleaning products,
white spirit, thinners, petrol or similar
under any circumstances. Such cleaning
agents may damage the delicate surface
of the housing.
• Ideally, you should remove dust or small amounts
of dirt with a dry, smooth leather cloth.
• Use a damp cloth to rub off stubborn dirt. Make
sure that no liquid penetrates the housing.
• Then immediately wipe the damp surfaces off with
a soft cloth without applying pressure.
13 • S 6000 SW THX® Select
Page 14
Troubleshooting
The following advice should help you to solve problems. If this does not help, you will find useful information
in the detailed FAQs on our website. Otherwise, please contact our hotline (see page 3). Take note of the
warranty instructions.
Problem Possible cause Solution
The subwoofer doesn’t
work.
The subwoofer is off or doesn’t
have any power.
The level for automatic activation
is set too low.
Fuse defective. 1. 2.
Activate the subwoofer with the switch (7).
Check the power cord and socket.
Use the AUTO LEVEL control (11) to increase
the level.
Try to set the switch (9) from “AUTO” to “ON”.
The subwoofer hums. The subwoofer is connected to a
different power circuit from the
rest of the system.
The hum is due to line disturbance.
The humming is caused by a
multiple socket strip.
The subwoofer is too
quiet.
The subwoofer does not
automatically turn off.
If operated via a cable
connection: Playback is
noisy.
For a wireless connection: The transmission is
disrupted.
A small number of AV receivers
provide a level that is too low at
the subwoofer output.
The AUTO/ON (26) switch is not
set to “Auto”.
The audio cable between the AV
receiver and subwoofer is too
long and/or the shielding is not
sufficient.
Other wireless signal sources
(cordless telephones, Wi-Fi
stations or microwaves) affect
the connection.
Disconnect the mains
cord.
Carefully pull the fuse
holder on the mains
connection jack out.
Connect the subwoofer and amplifier/receiver
to the same power circuit.
Buy a mains filter and connect both devices to
it.
Use a different multiple socket strip or connect
the subwoofer directly to the wall socket. It may
also help to insert the mains plug in the socket
the other way around.
In the menu of the AV receiver, set the
subwoofer level to maximum. Also set the
volume control on the back of the subwoofer to
maximum. You can also reduce the individual
levels of the other speakers.
Set the AUTO/ON (26) switch to “Auto”.
If possible, use a short, well shielded RCA cable
or use the wireless connection.
Move the devices causing the disturbance.
Push the old fuse
down and out. Insert a
new fuse (2 A delayed
action) and push the
holder back.
14 • S 6000 SW THX® Select
Page 15
Dimensions (WxHxD) 370 x 474 x 540 mm
Weight 23.6 kg (without metal grid)
Operating voltage 230 V~/50 Hz
Max. power consumption 250 watts
You can find further technical data on our website. Technical changes reserved!
Declaration of Conformity
Lautsprecher Teufel GmbH hereby declares that this product is in accordance with the requirements of directives 2014/30/EU, 2014/35/EU and 2014/53/EU as long as it is installed and used
according to the manufacturer‘s instructions. The full text of the EU Declaration of Conformity is
available at the following Internet address:
www.teufelaudio.com/declaration-of-conformity.html
Technical Data
The following radio frequency bands and radio transmitters are used in this product:
Radio network Frequency bands in Mhz Transmitter power in mW/dBm
Averna 2405–2477.5 1/0
15 • S 6000 SW THX® Select
Page 16
Please contact our customer service department with any questions,
suggestions, or complaints:
Lautsprecher Teufel GmbH
BIKINI Berlin
Budapester Str. 44
10787 Berlin (Germany)
Tel.: 00800 200 300 40
Fax: +4930 / 300 930 930
www.teufelaudio.co.uk/contact.html
No responsibility is assumed for the
correctness of this information.
Technical changes, typographical
errors and other errors reserved.
Manual No. 195101 GB 20170615
Loading...