Page 1
Column Speakers
CL 250 FR
... makes you happy
Proper use
Only use the speaker as described in these operating instructions. Any other use will be deemed as not in accordance with
the instructions and may lead to damage of property or even
persons. The manufacturer accepts no liability for damage
caused by use not in accordance with the
instructions. The
speaker is intended for private use.
Before operating the speaker, please read the safety
notes and operating instructions carefully. This is the
only way to use all functions safely and reliably. Keep
the operating instructions safe and pass them on to anyone
who may own the unit after you.
Notice
The information in this document may change without prior
notice and in no way constitutes any liability on the part of
Lautsprecher Teufel GmbH. No part of these instructions may
be reproduced in any form or be broadcasted in any way electronically, mechanically, by photocopy or recording without the
written permission of Lautsprecher Teufel GmbH.
Original packaging
If you wish to exercise your eight-week right of return, we ask
that you be absolutely sure to hold onto the packaging. We can
only accept the return of a device WITH THE ORIGINAL PACKAGING. Empty boxes are not available!
Complaints
In case of a complaint we implicitly need your invoice number
and the serial or lot number for processing. The serial number
can be found on the back side of the device.
Many thanks for your support!
Cont ac t
For questions, suggestions or criticism please contact our
customer service department:
Lautsprecher Teufel GmbH
Gewerbehof Buelowbogen
Buelowstrasse 66
10783 Berlin (Germany)
Phone 00800 - 200 300 40 (free of charge)
Fax: +49 (0)30 / 300 930 930
E-mail: service@teufelaudio.com
www.teufelaudio.com
General notes and information
Technical Description and
Operating Instructions
Dimensions (W x H x D) 25 cm x 127 cm x 25 cm
Weight 6,75 kg
Nominal impedance 4 – 8 Ω
Technical changes reserved!
You can nd further technical data on our website.
This product conforms with Council of the European
Union guidelines 2004/108/EC and 2006/95/EC
Technical data
Page 2
a
b
c
Caut ion icons
You will nd the following caution icons in these instructions:
High risk! Failure to observe the warning may result
in severe personal injury or death.
=
Danger
Moderate risk! Failure to observe the warning may
result in property damage.
=
Attention
Minor risk! Points which should be observed when
handling the unit.
=
a 2 x column speaker CL 250 FR
b 2 x base plate
c 4 x screw and washer
Check that all items have been delivered and that
nothing is damaged. In case of damage do not use
the product. Instead, contact our service centre.
Unpacking
• Carefully open the boxes, remove the speakers together
with the EPE foam parts and remove the foam parts without
touching the diaphragms.
Attention
Fire hazard!
Improper use may lead to damage or re.
• Do not place open ames such as burning candles or
similar on the unit.
• Ensure sufcient ventilation.
• Do not place the unit in direct sunlight.
• Only use the unit in indoor areas.
• Do not operate the unit in moist areas and protect it from
drops of water and splash water.
Also take care not to stand vases or other containers lled
with liquid on or near the unit in order to avoid liquid getting into the housing.
Danger
Danger of injury/damage!
Incorrect location may result in damage.
• Never use the unit unmounted in vehicles, in unstable
locations, on wobbly stands or furniture, on underdimensioned brackets etc. The speakers could tip or fall
down and cause injury to persons or be damaged.
• Place the speakers on the ground only.
• Place the speakers in such a way that they cannot be
knocked over unseen and make sure that the cables do
not pose a trip hazard.
• Carefully follow the installation instructions.
• Only use the supplied base plate.
• Do not place the unit near sources of heat (e.g. heaters,
ovens, other heat generating equipment such as ampliers etc.).
Danger
Danger to children!
Children can become trapped in the packing lm
when playing and suffocate.
• Do not allow children to play with the unit or the packing
lm. Danger of suffocation.
• Ensure that children do not remove small parts from the
unit or take them off of the unit (e.g. control knobs or plug
adapters). They could swallow the parts and choke.
Never allow children to operate electrical devices unsupervised.
Danger to hearing
Loud noise may lead to hearing loss.
Particularly when the subwoofer has been set
to maximum volume and the unit is activated, very high
noise pressure may suddenly be produced. This may have
psychological consequences and also cause physical injury.
Children and pets are particularly at risk.
• Set your signal source unit volume control to a low setting.
• When the volume is set high, always keep a certain dis-
tance from the unit and never place your ear directly on
the speaker.
• To avoid damage to health, avoid extended listening at
high volume.
Safety notes
Product contents / Unpacking
Page 3
Mounting t he base plate
The base plate ensures a safe position of the speaker and it
minimises vibrations
.
You need a Phillips screwdriver for assembly.
1. Lay the speaker with the back side on a soft, padded base
carefully (e.g. on the polystyrene pads from the packaging).
2. Place the base plate b on the speaker bottom carefully and
screw tighten it with 2 screws/washers c.
Vorbereitung
Setup and Connection
Setup
Note
Our website contains comprehensive notes for correct setup.
• Select a stable, level base.
• Make sure that the environment is clean and free from dust.
• Avoid placing the unit close to sources of heat or in direct
sunlight.
• Arrange the connector cables so that they do not pose a trip
hazard.
• Do not place any heavy objects on the cables or the speakers.
• Make sure that the speaker has a stable position to prevent
vibrations.
Removing the protec tive grids
The protective grids are attached by pins
and sockets on the front of the speaker
and can be easily removed. When the protective grids are removed, high frequency
output becomes clearer in particular.
To remove the protective grids, reach
behind them and slowly pull them off to the
front.
Attention
Risk of damage!
Make sure that you do not
touch the highly sensitive
diaphragms.
Connecting
Danger
Danger of injury/damage!
Arrange the cables so that they do not pose a
trip hazard.
1. Pull the power plug of your amplier/AV receiver out or multichannel active subwoofer of the outlet.
2. Lay the speaker cables from your amplier/AV receiver or
multi-channel active subwoofer to each speaker. These
cables should be high-quality double-wire speaker cable with
marked strands.
3. A connector comprising two terminals is located on the
back side of each speaker, to which you have to connect the
speaker cables.
The terminal clips are each marked red (+) and black (-).
Make sure the polarity is correct!
Connect the like coloured terminals. Otherwise the
sound quality will suffer.
The speaker connections of your
amplier/
AV receiver or
multi-channel active subwoofer
should be marked similarly.
The strands of the speaker cables are marked with different
colours or shapes.
4. Split the single wire down to approx. 30 mm on both ends
and strip approx. 10 mm of insulation off of each cord.
5. Twist the stripped single wire ends together so that no wire
protrudes. Tin coating is not necessary.
6. Turn the connector terminal counterclockwise until loose.
Run the stripped cable end into the now visible hole. Close
the terminal by turning it clockwise. The cable has now been
clamped in place.
7. Connect the cables to the other speaker in the same way.
8. Connect the speaker cables to your amplier/AV receiver
or
multi-channel active subwoofer. The operating instructions of
the appliance should contain notes on this.
9. Reinsert the power plug of your amplier/AV receiver or
multi-channel active subwoofer into the outlet.
Cros sover frequency
The ideal separation frequency for this speakers is 150 Hz. Set
this value on the amplier/AV receiver or DecoderStation.
c
c
Page 4
Lautsprecher Teufel GmbH
Gewerbehof Buelowbogen - Aufgang D1
Buelowstr. 66, 10783 Berlin (Germany)
Phone: 00800 - 200 300 40
(free of charge)
Fax: +49 (0)30 / 300 930 930
... makes you happy
No responsibility is as sumed for the correctness of this information. Technical changes, typographical errors and other errors reserved. Instruction No. 92225 S GB 20120816 / HC-HAM
Clean the speaker regularly with a soft, damp microbre cloth.
Please be absolutely sure to observe the following notes in the
process:
• If possible, only use plain water without any additives. In
case of stubborn marks, a mild soap solution may be used.
• Make sure that no liquid penetrates the unit.
Cleaning and care
Attention
Risk of damage!
Using the wrong cleaning materials may damage
the delicate surface of the case.
If possible, only use plain water without any additives. In
case of stubborn marks, a mild soap solution may be used.
In no circumstances should caustic cleaning products, white
spirit, thinners, petrol or similar be used for cleaning.
The following notes and further detailed information on our website should help you to rectify malfunctions. If this does not lead
to success, please contact our hotline
00800 - 200 300 40 (free of charge). Please also observe the warranty notes.
Problem Possible cause Solution
Playback is noisy. In general, the speaker is very low-noise. In
most cases, the speaker system with exceptional resolution in the high range area can
expose the poor quality of a signal source
(e.g. from MP3 les).
Ensure that the source is sending a clear signal.
The sound seems dull. The speakers have been connected with the
wrong poles.
Verify the correct connection of the cables for all speakers.
Disposal of the unit
Used units must not be disposed of with
household waste.
If the unit is no longer operational, every consumer
is required by law to dispose of used devices
separately from household waste, e.g. at a collec-
Troubleshooting
Protecting the environment
tion point run by the communal authority borough. In this way
it is ensured, that used devices are properly recycled and that
negative consequences on the environment are avoided. For
this reason, electrical equipment is labelled with the displayed
symbol.
Loading...