Vacuum Operating Instruct
ions
International Service 497 (AB) & Electronic Service 497 (ABF)
English
Visit us at www.TestEquipmentDepot.com
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
This Vacuum is Intended for Commercial Use Only
Important Safety Instructions —
Save These Instructions
Read all instructions before using the vacuum.
When using an electrical appliance, always use basic precautions,
including the following:
!
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY, FOLLOW THESE SAFETY RULES:
1. Use only as described in this manual. Use only manufacturer’s recommended attachments.
2. Do not use this machine to vacuum hazardous dust.
3. Connect to a properly grounded outlet only. See Grounding Instructions.
4. Do not use without filter in place
5. Do not leave appliance plugged in when not in use. Unplug from outlet when not in use and before servicing.
6. Turn off all controls before unplugging.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle plug or appliance with wet hands.
9. Do not use appliance outdoors or on wet surfaces. Electric shock could occur.
10. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped or damaged,
left outdoors, or dropped in water, discontinue use.
11. Do not pull or carry by cord, use cord as a handle, close a door on cord or pull cord around sharp edges and
corners. Do not run appliance over cord. Keep cord away from heated surfaces.
12. Do not put any object into openings. Do not use with any opening blocked. Keep openings free of dust, lint,
hair, and anything that may reduce air fl w.
13. Keep hair, loose clothing, fingers, and all body pa ts away from openings and moving parts.
14. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
15. Do not use to pick up flamma le or combustible liquids, such as gasoline, and do not use in areas where these
may be present.
16. Do not allow to be used as a toy. Close attention is necessary when used near children.
International Electronic/Service Vacuum Operating Instructions
1
Grounding/Earthing
Instructions
!
DANGER
This appliance must be grounded/
earthed.
The wires in this main lead are
colored in accordance with the
following code:
Green/Yellow: Earth
Blue: Neutral
Brown: Live
As the colors may not correspond
with the colored markings identifying
the terminals in your plug, proceed as
follows:
The wire which is colored Green/
Yellow must be connected to the
terminal in the plug which is marked
with the letter “E” or by the ground/
earth symbol “ ” or colored Green
or Green/Yellow.
The wire which is colored Blue must
be connected to the terminal in the
plug which is marked with the letter
“N” or colored Black or Blue.
The wire which is colored Brown
must be connected to the terminal in
the plug which is marked with the
letter “L” or colored Brown or Red.
Specifications
Electrical
220-240 V
50/60 Hz
3.7 amps
Dimensions
Length 17-13/16 in.
Width 7-3/4 in.
Height 9-1/4 in.
Certification
Meets VDE RFI 0875 Conducted
Limits.
Conforms to EMC Requirements Defined in:
EUROPEAN STANDARD EN 55014 (1993) - Conducted Emissions
CISPR 14 Third Edition (1993-01) - Conducted Emissions
EN60555-3 - Harmonic Current Emissions (Class A)
IEC 1000-3-2 - Harmonic Current Emissions (Class A)
EUROPEAN STANDARD EN 50082-1 (1992), Immunity
IEC Publication 801-2 (1991) - ESD, Contact Discharge, Severity Level 4
- ESD, Air Discharge, Severity Level 4
IEC Publication 801-3 (1991) - Radiated Immunity, Severity Level 2
IEC Publication 801-4 (1998) - EFT, Severity Level 3
prIEC Draft 801-5 - Surge, Severity Level 3
Motor
1 H.P.
Continuous duty rated with one sealed
ball bearing and one sleeve bearing
lubricated for life. Internal thermal
breaker opens at 221°F [105°C] and
automatically closes when motor cools
(after about 30 minutes).
BSI: Internal thermal breaker opens
at 274°F [120°C] and automatically
closes when motor cools (after about 30
minutes).
2
International Electronic/Service Vacuum Operating Instructions
To Operate
Step 2
Unfasten accessory
door and remove vacuum
hose, electrical cord and
hose attachments.
Step 3
Remove filter plug from
vacuum inlet (always
replace when repacking for
transport).
Step 4
Attach selected
accessory to hose (insert
crevice brush as shown).
Insert other end of hose
into inlet.
Step 1
Release latches
and open lid.
Step 5
Place remaining accessory and
filter plug in lid. Close lid.
Step 7
Insert hooded end
of power cord in power
cord receptacle on
vacuum as shown.
Follow the steps in the illustration.
DO NOT OPERATE WHEN FILTER
IS FULL. A lack of exhaust air, or
diminished suction, indicates a full filter.
!
WARNING
ELECTRIC SHOCK COULD
OCCUR IF USED OUTDOORS
OR ON WET SURFACES.
Step 6
Latch lid securely.
1. Release the latches and open the lid.
2. Unfasten the accessory door and
remove the vacuum hose, electrical
cord and hose attachments.
3. Remove the L-15X filter plug from
the vacuum inlet (always replace when
the vacuum is not in use or repacking
for transport).
4. Attach the selected accessory to the
hose (insert the crevice brush as
shown). Insert the hose into the inlet.
5. Place the other accessories and plug in
the lid. Close the lid.
Step 8
Plug cord into
power receptacle.
Step 9
Turn on power switch.
6. Latch the lid securely.
7. Plug the cord into the vacuum.
8. Plug the cord into the power
receptacle.
9. Turn on the power switch.
Note
The motor has a thermal breaker that
opens and stops the motor if it
overheats. This usually occurs if the
filter is full and needs to be replaced.
The motor will restart automatically
when it cools (after about 30 minutes).
International Electronic/Service Vacuum Operating Instructions
3
To Store Attachments
for Transport
1. Unplug the power cord from the
outlet and the vacuum.
2. Open the lid and retrieve the L-15X
filter plug.
3. Remove the hose from the inlet and
insert the L-15X filter plug.
4. Detach the hose nozzle from the base.
5. Place the hose, power cord and
attachments into the lid and close the
accessory door.
6. Close the lid and securely fasten the
latches.
To Replace Filter
The Vacuum is designed for use with
disposable Filters. The Filters must be
replaced on a regular basis. Frequency
of filter replacement depends on the
type and frequency of use of the
Service Vacuum.
1. Release the latches and open the lid.
2. Remove either the L-15X filter plug
or hose. Save the plug for use later
(see note below).
3. Grasp the filter and pull it straight up
4. Insert the L-14X filter plug in the
filte .
5. Dispose of the filter in a suita le
manner.
6. Remove the L-14X plug from the new
filter and position filter in the acuum
with the filter hole to our left. Save
the L-14X plug for use in disposing
the filter (see note bel w).
7. Verify that the gasket between the
filter and the motor fits tigh y.
8. Insert the L-15X filter plug or hose
9. Close and latch the lid.
Note: The L-15X plug (longer plug) is
used to cover the filter inlet for storage
when the vacuum cleaner is not in use.
This plug comes with the filter in a
new vacuum cleaner. The L-14X plug
(shorter plug) is used to cover the filter
inlet for disposal. This plug comes with
each new replacement filte .
!
WARNING
ELECTRIC SHOCK COULD
OCCUR IF USED OUTDOORS
OR ON WET SURFACES!
!
CAUTION
Do not operate when filter
is full. A lack of suction or
exhaust is an indication of a
full filter.
!
CAUTION
To avoid risk of fire, filter
must be installed properly
and replaced regularly. Do
not open filter, reuse filter or
attempt to replace components
within filter.
4
International Electronic/Service Vacuum Operating Instructions
Parts List
Item Part Number Description Type of Vacuum
1 78-8063-1943-6 Receptacle, 220V (SV-PCR6) Service/Electronics
2 26-1011-8421-1 Power Cord, 250V, 10 amp Service/Electronics
3 78-8063-2418-8 Vacuum Hose Assembly (SV-SH32) Service/Electronics
4 80-6104-7958-8 Crevice Nozzle (SV-CN1) Service/Electronics
5 78-8063-1540-0 Curved Wand Nozzle (SV-WA2) Service/Electronics
6 78-8005-5350-1 Type 2 Filter, Toner/Dust (SV-MPF2) Service/Electronics
7 80-6104-7957-0 Crevice Brush (SV-CB1) Service/Electronics
8 80-6104-7640-2 Short Red Filter Plug L-14X (SV-SRP) Service/Electronics
9 80-6104-7639-4 Long Red Filter Plug L-15X (SV-LRP) Service/Electronics
Important
Power cord must be VDE SEMKO approved 250 V, 10 amp
International Electronic/Service Vacuum Operating Instructions
5
Professional’s Guide to
Filter Selection
Now you have a choice of two distinctly
different filters designed to do distinctly
different jobs with your Service
Vacuum Cleaner. Make a professional
decision on which filter meets your inhouse or client clean-up requirements.
• Type I Filter for extremely fine
particles
• Type 2 Filter for toners and
dust
The two filters described in this
“Professional’s Guide to Filter
Selection” are completely disposable.
Replacements are easy and clean.
Type 1 Filter, Fine Particle
A thinner, more concentrated weave
(HEPA media) for trapping extremely
fine particles to 0.3 microns. Typical
applications are color laser printers,
color copiers and highly sensitive
equipment.
Type 2 Filter, Toner/Dust
Specifically designed for trapping
unwanted toner from copiers and laser
printers. Also ideal for cleaning data
processing equipment.
Visit us at www.TestEquipmentDepot.com
6 International Electronic/Service
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Vacuum Operating Instructions
Loading...