Installation Guide
AU-PBD350VA
Table of Contents
Section .....................................................................................
1.0 Product Range ..................................................................
2.0 Description ........................................................................
3.0 Features ............................................................................
2.0 Description
The Push Button LED Dimmer is an Integrally Switched,Push
Button,modular dimmer mechanism rated at 350 VA. Up to six
dimmer mechanisms can be installed in a plate!
Designed for LED lamps, the unit utilises powerful and
sophisticated dimming technology to provide control.
The LED Dimmer also incorporates over-current and thermal
fuse cutoff (non-recoverable) protection devices and is capable
of withstanding persistent short circuit conditions.
3.0 Features
• Integrally switched modular dimming mechanism
• 350 VA Power Rating
• Two-wire phase control wall plate dimmer.
• Soft-start for lamp and driver life.
• Provide optimised dimming of LED based lamps and drivers.
• Compatibility with incandescent lamps,240 V halogen lamps,
Low voltage halogen lamp with dimmable electronic
transformer, etc
• User adjustable minimum and maximum brightness
• Multi-gang capacity up to six (6) dimmer mechanisms per
plate
• Wall or architrave mounting options.
• Wide range of plate styles and colour variants available.
• Suitable for new installations or retro-fit applications.
• Inbuilt Over-Current and Over-Temperature protection.
• Full short circuit protection.
• Immune to high frequency (ripple) signal injection on mains
supply.
• Complies with Australian and International EMC Standards.
4.0 Dimmer Unit Operation .....................................................
5.0 LED Indicator ....................................................................
6.0 Electrical Specification......................................................
7.0 Load Compatibility ............................................................
8.0 Incompatible Loads ...........................................................
9.0 Wiring Diagram .................................................................
10.0 Installation .........................................................................
11.0 Warranty Statement...........................................................
1.0 Product Range
Product No. Description
Push Button LED Dimmer,350 VAAU-PBD350VA
4.0 Dimmer Unit Opetration
Dimming Long press dimming button to dimming
Short press dimming button to on/offON/OFF
Minimum brightness setting
1) Remove the top cap
2) Long press programming
button until LED flash(Slow
flashing)
3) Long press dimming button to
the setting level
4) Double press dimming button
Programming
to exit programming mode
Maximum brightness setting
1) Remove the top cap
2) Long press programming
button until LED flash, short
press programming button, LED
start to flash fast
3) Long press dimming button to
the setting level
4) Double press dimming button
to exit programming mode
5.0 LED Indicator
The unit incorporates an LED indicator to display the status
of the load.
LOAD STATUS INDICATOR STATUS
ONON
OFFOFF
6.0 Electrical Specification
9.0 Wiring Diagram
Neutral
One-Way Wiring Diagram
Parameter
Nominal Operating Voltage
Nominal Operating
Frequency
Maximum Load
Value
220-240 V～
50 Hz
350 VA @1 Gang
Derate for multi-gang applications
Minimum Load 10 VA
Dimming Technique Trailing Edge Phase Control
Mounting Centres 84mm Australian Pattern Plate
Safety Compliance
AS/NZS 3100, AS/NZS 3133, IEC 60669-2-1
AS/NZS CISPR15, IEC 60669-2-1 (26.1, 26.2),
EMC Compliance
IEC 61000-3-2 (Excepting when used in
conjunction with Electronic loads)
Specifications Typical @ 240 V～ 25℃
Suitable for Indoor Use Only
No User Serviceable Parts Inside
7.0 Load Compatibility
AT-PBD350VA
Load Symbol
Compatible Loads
Maximum Load
Minimum Load
Neutral
Two-way Wiring Diagram
NOTE:
• The LED dimmer series are designed for One-Way or
Two-Way operation as above diagrams.
• Two or more dimmers cannot be connected in parallel or
series to control the same load from two different locations.
• Dimmer Mechanism wiring is NOT polarity sensitive
It is illegal for persons other than an appropriately
licensed electrical contractor or other persons authorised
by legislation to work on the fixed wiring of any electrical
installation. Penalties for conviction are severe!
10.0 Installation
To connect the required lighting loads, then follow the following
steps:
Step 1
Leave the dimmer connected,but
remove the dimming cap from the top
button of the dimmer.
Step 2
Align the pillar on the front of the top
with the hole in the cap of dimmer.
button
Dimmable LED Lighting
Incandescent Lighting
240 V Halogen Lamps
Low Voltage Halogen
Lightingwith Electronic
Transformers
150 W 10 W
350 W 10 W
350 VA 10 VA
Step 3
Push the dimmer cap back and make
sure the pillar insert the hole and all
the snap-fit structure assembly
successfully.
You can choose one king of the caps
when you buy this dimmer ,to meet
different style of products.
8.0 Incompatible Loads
This dimmer is not compatible for use non-dimmable linear or
compact fluorescent lamps.Use
only lamps / ballasts that are compatible with phase angle
control.
11.0 Warranty Statement
• This SHYUGJ product is guaranteed against faulty workmanship and
materials for a period of two years from the date of installation.
• This warranty is expressly subject to the SHYUGJ product being installed, wired,
tested, operated and used in accordance with the manufacturer's instructions.
Loading...