Tesco PET 1 User Manual

User
Guide

PET 1

Upright Vacuum Cleaner

IMPORTANT SAFETY INFORMATION

To reduce the risk offire, electrical shock, or injury:

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

Read all the instructions carefully before using your
appliance and keep them for future reference. If you pass
the product on to athirdparty, include this manual.

Unplug the appliance from the mains supply when not in
use, removing or attaching filters,accessories, the dust cup
and and before cleaning anypartofthe appliance.

When unplugging, hold the plug top, notthepower cord.
Do not immerse the body of the cleaner or the electrical

cord or plug in waterorliquids.
Never leave the cleaner unattendedwhenit is connected to

the electricity supply.
Do not use outdoors indamporwet weather
Do not use your appliance indoors in damp or wet

conditions.
Do not use attachments or accessories not recommended

by the manufacturer.
Close supervision is necessary when an appliance is used

near children. Children should notoperatethisappliance.
This appliance is for household use. Do not use for any

purpose not expressly specified inthismanual.
There are no user serviceable parts in this appliance.

Unauthorised dismantling or servicing will void the warranty.
If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified
person in order to avoidahazard

Refer all servicing which involves the taking or putting on of
parts (other thanthosespecifically referred to in this manual),
to a qualified repair person or approved service centre.

Do not use attachments or accessories which are not
recommended by the manufacturer. They may cause
malfunction or injury.

Do not use harsh abrasives, or caustic cleaners when
cleaning this appliance.

Store the appliance away from direct sunlight, with all
accessories detached and out of the reach of children.

Before using this appliance ensure that the voltage of your
electricity supply is the same as that indicated on the rating
plate of the appliance.

Class II construction double insulated. This product
must not be connected toearth.

This appliance is intended only for household use. It must be
properly installed and operated in accordance with these
instructions. Failure to do this will invalidate thewarranty.

Electrical Information

Warranty

SPECIFICATIONS

Model:
Voltage:
Power:

PET 1
220-240 V AC 50Hz
1800W( max.) 1400W (nom.)

Your appliance is covered by a warranty for 12 months from
the date of purchase. If a fault develops during this period,
please return the unit to your nearest Tesco store together with
the original receipt as proof of purchase. This warranty in no
way affects your consumer rights

UK:

ROI:

Waste electrical products should not be disposed of

with household waste.

e for details.

Produced after 13th August 2005. Waste electrical
products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice.

Separate disposal facilities exist, for
your nearest facilities. See www.recycle-more.co.uk or in­stor

PET 1 Vacuum Cleaner User Guide

Page 2

When operating your cleaner:

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

$

Do NOT

Do NOT

Do NOT
Do NOT
Do NOT

Do NOT

Do NOT

Do NOT
Do NOT

Do NOT

Do NOT
Do NOT
Do NOT

DO NOT

use the vacuum cleaner if it has been dropped,

damaged, left outdoors, or droppedintowater.

pull or carry the cleaner by the cord, closea door
on the cord, or pull the cord around sharp edges or
corners.

Use the handle to carryandmovethe cleaner.

run the appliance over thepowercord.

handle the mains plug orcleanerwithwet hands.

use the vacuum cleaner to pick up large objects

or objects that are likelytodamagethe vacuum cleaner.

attempt to vacuum long hair, string, pieces of
cloth, etc. when vacuuming carpets or floors. These will
snag in the brush andmaystopit rotating altogether.

Keep hair, loose clothing, jewellery, fingers, feet and all
parts of your body awayfromopeningsand moving parts.

operate the cleaner in bare feet or when wearing

open toed footwear.

vacuum hot items; e.g. cigarettes, matches, ashes.

vacuum hard or metal objects,nailspins,etc.

Set the cleaner fullyupright and switch it off beforeplugging
or unplugging the vacuumcleaner into the mains.

Use extra care when vacuumingonstairs

pick up toxic, or flammable materials or use in

the presence of explosive ortoxicdust,liquids or vapour.
Use only on dry, indoor surfaces.

put any objects into openings.
use with any opening blocked.
use without all the filtersinplace.

Keep all vents openings and attachments free of dust, lint,
hair and anything else thatmayreduceair flow.

Keep the end of the hose and all attachments away from
your face and body.

When cleaning carpets, keep the vacuum cleaner head
moving to avoid damaging thecarpet.

use the cleaner on hard floors, whether wood,
laminate or plastic, with the brush set up to clean carpets.
This cleaner is exceptionally powerful and the floor could
be scratched or otherwise damaged.

Use the appropriate setting. Cleaning deep pile carpets
with the floor setting coulddamagethecarpet.

If the appliance becomes clogged, switch off and unplug
the power cord before clearingtheobstruction.

!

Assembly

1.

2.

3.

.

5.

Press the upper handle
release down and raise the
handle vertically until it clicks into
place.

2. Push the front
hoses into the
retaining sockets.
there is a guide
on each hose so
you can only
insert it the
correct way.

Coil the hose around the cleaner as shown in the top RH
picture.

Raise the Upper Power Cord
cleat vertical and coil the cable
round the cleats. (The upper cleat
can be rotated to facilitate easy
release of the power cordinuse.)

4 Assemble the two piece tube
onto the hose and insert the hose
into the retaining boss.

Assemble the accessories as
shown in the illustrations

Your cleaner is now ready for use.

Your Vacuum Cleaner and its accessories.

PET 1 Vacuum Cleaner User Guide

Page 3

Mains ON/OFF

Switch

Adjustable

Upper Handle

Carrying

Handle

Dust Cup Handle

Dust Cup

Flexible Hose

Carpet Height

Adjustor

Exhaust

Filter Cover

Front Hoses

Upper

Handle Release

Upper Power

Cord Cleat

Crevice Tool

Small
Brush

Upholstery

Brush

2 Piece

Extension Tube

Furniture Guard

Power Head

Dust Trap

Cover

Lower Power

Cord Cleat

Power Cord

Top Handle

Front View

Rear View

Handle
Release

Turbo Brush

SET

RELEASE

Operating the Cleaner

Before using your cleaner:

Switch on your cleaner:

Set the cleaner height:

NEVER leave the cleaner in a lowered position and
switched on as the brushcould scratch the floor surface.

Set the cleaner

fully upright.

Press the Mains ON/OFF switch on the
handle to the “ ” position to switch the
cleaner .

Turn the Upper Power Cord cleat down 180º
and release the power cord.

Uncoil the power cord fully.

Plug the power cord intotheelectricaloutlet.

Switch on at the mainspoint.

Slide the Mains ON/OFF switch on

the cleaner handle to the“ ”position to switch the cleaner .

With your foot, depress the handle releasepedalas shown.

The cleaner can now be angled for normal operation and for
low level cleaning.

To get the cleaner to lie flat, press the release pedal once,
partially lower the handle andthendepressthe pedal again.

Return the cleaner to the upright position and

ensure it locks in place.Thisraisesthe brush clear of the floor.

For convenience, you may reset the upper cleat and then hook
the cable over the cleat.Thiswillhelp stop the cable snagging.

O

OFF

ION

When you wish to movethe cleaner or take a break:

Switch off.

Page 4

Vacuuming Carpets and Hard Floors

Set the vacuuming height before commencing cleaning.
Always check the carpet or floor covering manufacturer's
recommended cleaning instructions beforevacuuming.

Suggested Pile Height Settings:

Long pile, deep scatterrugs.

Medium to long pile.

Short to medium pile.

Short pile.

Hard floors.

CAUTION: Setting the vacuuming height should only be
done when the cleaner isswitched off at the mains.

Do not attempt to vacuum rubber bands, long
hair, string, pieces of cloth, etc. These will snag in the
bristles and may even stopthe brush rotating altogether.

immediately.

Stand the cleaner fully upright.

Turn the carpet height adjustmentknobtothe desired setting.

You may need to raise the

brush height for easier accesstoscatterrugs, etc.

If this happens, switch the cleaner off Invert the
cleaner and completely remove all obstructionsfrom the brush
before switching the cleaner onagain.

CAUTION.

Using your Vacuum Cleaner

PET 1 Vacuum Cleaner User Guide

ADJUSTING THE CLEANER ANGLE

OFF

ON

Using the accessories

Moving the cleaner

General Do's and Don'ts

Switch the cleaner at the
mains switch on the handle.

Place the cleaner fully in the upright
position.

Set the Brush Control knob to

Lift out the hose and free it from
the retaining clip at the side of the
cleaner.

If you wish to use the extension
tubes and accessories, lift the tube
assembly out and attach it to the
hose.

There are two extension tubes. They fit inside each other and
some pulling force may benecessarytoseparate them.

The accessories can be used directly on the hose, or with a
short or long tube asyouneed.

Use the crevice tool for radiators, crevices,

between cushions, joins in stairtreads,etc.

Use to clean upholstery, curtains, etc.

Use to clean upholstery, plush toys, etc.

This is a powerful tool. The brush is driven at
high speed by the air being sucked into the cleaner. Use it to
clean small rugs, or areas of bare floor which the normal
vacuum cleaner head cannot reach.

You can use the accessories withthe handle extended or folded
down - this position isusefulforcleaning stairs, etc.

Always switch the cleaner off before putting on or removing
accessories.

After use always return the accessories to their storage areas in
the cleaner and re-connect the hose to the cleaner.

When moving the cleaner between locations always unplug
the power cord and wind it around the cleats. Accessories
should be safely stowed.

the cleaner must be moved with both hands when it is
extended. Wherever possible we suggest the cleaner is moved
in the folded position.

pull the vacuum cleaner aroundthe room by the hose

as it could tip overandcausedamage.

over extend the hose. Trying to reach beyond the

hose length could cause thevacuumtotip over.

Be especially careful on stairs.

pull or carry the cleaner by the cord, close a door on

the cord, or pull thecordaroundsharp edges or corners.

Use the carry handle when lifting or moving the cleaner
between different locations.

NEVER lift the cleaner with the upper handle only. It could
release and causeinjury.

If you are moving the cleaner a long way or up a flight of stairs,
switch off, fold the upper handle down, wind the power cord
and stow the hose andaccessories.

OFF

LONG PILE.

Extension tubes

Accessories

Crevice Tool:

Upholstery Brush:

Small Brush:

Turbo Brush:

Never attach or remove accessories when the vacuum
cleaner is switched on.

Do NOT

Do NOT

Do NOT

PET 1 Vacuum Cleaner User Guide

Page 5

Hose Collar

Inner Tube

Outer Tube

Extension Tubes

Crevice Tool

Turbo Brush

Upholstery

Tool

Small
Brush

To Hose Collar

To Accessory Attachment

Extended

Folded

Cleraring the Dust Trap Front Hose Blockage

The dust trap is locatedattherear of the cleaner.

Loft the trap up and clear any blockage fully. When you have
finished, close the trap door firmly. If the trap is not firmly
closed, the cleaner will notperformwell.

Remove the two hoses at the front of the cleaner and examine
the hoses and the cleaner head. Remove any blockage and
replace the hoses.

If the dust trap isclear and there is still a blockage:

PET 1 Vacuum Cleaner User Guide

When you have finished Vacuuming:

Set the cleaner fully upright.

Switch the cleaner off at the handle.

Unplug from the mains.

Set the upper cleat vertical and wind the cord around the upper
and lower cleats.

Re-assemble the hose and attachments if necessary.

Fold the upper handle down fully.

Empty the dust cup and clean the dust cup filters

Wipe the cleaner body with a damp cloth and dry thoroughly.

Store the cleaner safely out of the reach if children and pets.

(see Pages 7 & 8)

If the cleanerloses suction and the dust in the dust cupis below the mark, this maybe due to clogged filters or a blockage.

Set the cleaner upright, switchoffandunplug immediately. Empty the dust, check all the filtersandclean them.

Check the extension tubes andaccessoriesvisuallyand remove any blockage with a stick or broomhandle.

Invert the cleaner,inspectthebrush area, and remove any obstruction fromthe bristles or the brush roller.

MAX

If you suspect a blockage:

If this does not remove the blockage:

DO NOT

operate the cleaner if thesuction is impaired.

$

$

$

Clearing a Blockage

Page 6

IMPORTANT-Motor Thermostat

If the vacuum cleanershould overheat, the protective thermostat will automaticallyturn the unit off.

Switch off and unplug. Checkand clear any blockage and clean/replace thefilters.

Wait at least 45 minutes before attempting to reuse the cleaner. After the cleaner has cooled down plug in and
switch on. The vacuum shouldnow start.

contact the help lineon

If this occurs:

If the vacuum doesnot start: 0845 456 6767

Emptying the Dust Cup

Check and empty the dust cup
regularly to maintain the efficient
performance of the cleaner.

You empty the Dust Cup

the dirt reaches the MAX

mark.

Set the cleaner upright, switch off
and unplug.

must

before

The maximum dirt level is marked on
the Dust Cup.

Hold the Dust up by
the handle. Lift the
handle up and release
the dust cup from its
cradle. Carefully
remove the dust cup
from the cleaner,
keeping it vertical.

Invert the dust cup over a bin. Press the catch on the lid which
will pop open. Shake and tap the dust cup lightly to remove as
much dust as possible. Closethelid.

If you are still vacuuming, replace the cup.

When you have finished cleaning you must clean the two
filters in the cup after emptying it. This is essential. Referto
the next page for details.

Cleaning and Replacing the Filters

It is essential to inspect clean the filters regularly. The period between inspections will depend on how often and for how long you
use the cleaner. The motor inlet and exhaust
filters should be checked cleaning sessions.

If the cleaner shows any sign of losing suction, switch off, check and clean the filters and if necessary, clear any blockage.

Before you examine or clean the filters, Set the cleaner fully upright. Switch off and unplug from the mains.

The filter in the dust cup should be cleaned whenever you empty the dust.

after every three

NEVER operate the cleaner with clogged filters, you could damage the cleaner motor.

Filter Locations

Debris Screen

HEPA Filter

(Inside Dust Cup Lid)

The HEPA Filter stops nearly all dust
particles and airborneallergens from
re-entering theairyoubreathe.

You should also check and clean the
debris screen regularly.

Clean this filter every time you use
the cleaner. Failure to do this will
impair performance and may
damage the cleaner motor.

PET 1 Vacuum Cleaner User Guide

1. Press to Open

2. Tap and shake
to remove dust

Page 7

Pre-Motor Filter

Exhaust Filter

(behind cover)

PET 1 Vacuum Cleaner User Guide

Cleaning the Dust Cup Filters

HEPA Filter

Debris Screen

Remove the cup. Hold the cup as
shown. Rotate the cup lid to the
right to the UNLOCK position and
lift the lid off.

Hold the cup over a bin. In the cup
lid there is a spinner.

Rotate the spinner in both
directions to shake all the dust
off and thoroughly clean the
pleats of the filter.

At least once a month or if you
notice a decrease in suction,
remove and clean the filter.

To remove the filter:

Hold the filter as
shown. Keep the cup
still and rotate the
filter to the left to
loosen it. Now lift it
out.

After removing the
filter, tap the plastic
underside on the
edge of a bin to
remove loose dust.

Now brush the filter
out with a soft brush
and rinse it under the tap. Run the water on the dirty side until it
runs clear. After washing allow the HEPA Filter to fully air dry.

Only when the filter is dry

should you replace it intheDustCup.

To replace the filter, ensure
the rubber seal is in place
around the top edge of the
filter cage. Thread the filter
over the arms of the pleat
spinner and. Insert it fully
into the cup lid and twist
clockwise to lock it inplace.

The HEPA filter should be replaced at least every six months

to keep your cleaner inpeakcondition.

Open the dust cup. Hold the dust cup firmly with one hand.
Place your other hand inside the cup and take hold of the
debris screen tube.

Rotate the debris screen firmly to the right to unlock it and then
carefully withdraw the screen fromthetube.

Rinse the debris screen under the tap in lukewarm water to
remove any dust. The dust cup and dust cup cover can be
washed in lukewarm water.

After removing the filters he dust cup may now be washed out
in warm water and allowedtodry.

Do not use strong detergents. DO

Thread the screen over the vanes in the black inner tube. Align
the three lugs with the slots in the cup and turn fully
anticlockwise to lock firmly.

Replace the dust cup cover on the dust cup and replace the
assembled dust cup in thevacuumcleaner.

(There may be
some resistance from
the springy arms of
the spinner.)

(This may take up to 24 hours.)

(and ideally three)

NOT place any part in a

dishwasher. Allow all parts to fully dry.

To replace the screen:

Page 8

UNLOCK

LOCK

UNLOCK

LOCK

PET 1 Vacuum Cleaner User Guide

Cleaning Pre-Motor & Exhaust Filters

Check these filters whenever you remove the dust cup for
emptying and clean them whennecessary.

B. Exhaust Filter

Place a finger in the hole and press down.The cover
is spring loaded so you will need to pressdown firmly
and then lift the cover out

Remove the filter holder from the cage and rinse in
lukewarm water. A very soiled filter should be
thoroughly washed with fresh tepid water. with a
drop of mild detergent.Rinsewell. Let the filter air dry
for 24 hours.

Now re-install the filter insert in the holder. Replace
the holder in the cleaner.

Finally replace the cover.

A. Pre-Motor Filter

Remove the dust cup.Lift the pre-motor filter insert out. Rinse in
lukewarm water. A very soiled filter should be thoroughly
washed with fresh tepid water. with a drop of mild detergent.
Rinse well. Let the filterairdryfor 24 hours before re-installing.

Page 9

IMPORTANT NOTICE

If at any time you notice that the brush speed is slow and/or there is a loss of suction, this may be
caused by the brush getting clogged.

If this happens, switch the cleaner off and unplug it from the mains. Clean the brush area fully and
remove all obstructions before continuing to use the cleaner.

Prompt action will maintain cleaner performance and avoid any potential problems of belt slippage.

Lift out

to clean

A

B

Lift out

to clean

Lift out

PET 1 Vacuum Cleaner User Guide

Page 10

Changing the Brush Roller and Drive Belt

Sluggish speed and loss of suction may be caused by a worn or slack belt. If the cleaner does not pick up on carpets but is OK when
using the attachments this indicatesawornbrush roller. These components are user replaceable.

You need a No2 Phillips screwdriver,a25mm paint brush and a small flat bladed screwdrivertocarry out this procedure.

DO NOT replace these components yourselfunless you are confident that you cancarry out this procedure satisfactorily.

Make sure the cleaner is switched off and unplugged from the mains before you start work. Protect the work surface if
necessary.

2A

2B.

. Release the handle by pressing onthehandle release pedal twice and lay it flat onthefloor. Turn the cleaner over.

With a Phillips No. 2 screw driverremovethe 4 screws on the bottom plate as identified.

Ease the power head coveroff.Make sure you do not disturb the handle releasepedal.

Lift the belt off themotorspindle
Slide the belt off themotorspindle.
If you are not replacing the belt, clean it carefully with

a dry cloth to removeanyresidue.

Stage 3. Slide the Belt off the Motor

Stage 2. Remove the Power Head Cover

2A

2B

Stage 1. Detach the accessories and the front tubes

PET 1 Vacuum Cleaner User Guide

Page 11

ABLift the left side of the brush off its mounting. Press the casing out

with a screwdriver and easethebrushup and out of its mounting.

Repeat the procedure for the other side

Now lift the belt offthebrushand then remove the brush.

Stage 4. Remove the Brush and Belt

Stage 5. Thread the new
belt over the motor spindle

4A

4B

4A

4B

4A

4B

4A

4B

4A

4B

Stage 7. Align and Secure the Brush

Stage 6. Thread the brush through the belt

56

7A 7B

PET 1 Vacuum Cleaner User Guide

Cleaning and storage

Service and spares

If you have difficulty obtaining replacement spares, filters

0845 456

6767

When you have finished
Vacuuming:

Set the cleaner fully upright.
Switch the cleaner off at the handle.
Unplug from the mains.
Set the cleats vertical and rewind the

cord around the upper and lower
cleats.

Re-assemble the hose and attachments
if necessary.

Fold the upper handle down fully.
Empty the dust cup and clean the dust

cup filters

Wipe the cleaner body with a damp cloth and dry
thoroughly.

The plastic outer body shell and the exterior surfaces of the
attachments may be cleaned with a barely damp cloth and
then dried thoroughly.

Do NOT allow water or liquids to penetrate the vacuum
cleaner. This could be dangerous.

Detach all accessories and store the appliance away from
direct sunlight, and out ofthereachof children.

(see Pages 7 & 8)

$

$

, etc.

contact the TESCO electrical help line on

Please have your purchase receipt with you when you

call.

Tesco Stores Ltd, Delamare Road, Cheshunt, Herts, EN8 9SL

Page 12

OPERATING CAUTIONS

$

$

$

NEVER

If an obstruction occurs during cleaning:

If the vacuum cleanershould overheat, the protective thermostat will automaticallyturn the unit off.

Switch off and unplug. Checkand clear any blockage and clean/replace thefilters.

Wait at least 45 minutes before attempting to reuse the cleaner. After the cleaner has cooled down plug in and switch
on. The vacuum should nowstart.

contact the help lineon 0845 456 6767

operate the cleaner with damagedfiltersorwith a filter missing
Use approved filters and regularlycleanandreplace them.
Wind the cord around the cleats afteruse.

Turn the cleaner OFF and unplug. Check the dust level. Empty the dust cup. Check the

hose and the tubes forblockageandclear these manually following the instructions on Page 6.

If this occurs:

If the vacuum cleanerdoes not start: .

Stage 8. Rotate the brush by hand
to ensure the assembly moves smoothly

9A.

9B.

9C

9D.

Replace the power head cover.

Press the power head cover down by hand and check that it is
firmly seated all round. Check that the rubber gasket is in place and
not pinched between the coverandthemotor housing.

. Fix the cover in place with thefourscrews.

Re-fit the front hoses

Switch the cleaner on. Check the cleaner operates normally and that
the brush switch operates beforere-using the cleaner.

(See Stage 1).

Stage 9. Re-assembly

8

9A&B

9D