Nursery furniture cot
bed
A
ssembly instruction
s
www.tesco.com
Produced in Vietnam for TESCO Stores Ltd
.
Tesco
2013
C
2
IMPORTANT! RETAIN FOR FUTURE
REFERENCE: READ CAREFULL
Y
W
hen you are ready to star
t, make sure that you have plenty
of space and a clean, dry area for assembly
.
Dont's
Number of
people r
equired to assembl
e
One person to assemble the product
and two
people to lift it
into position
.
Time to assembl
e
Hi!
Look out me throughou
t this manual. Wherever you see
my picture I will have a handy tip to help you with the assembly
of your pr
oduct.
My firs
t tip is: Before you start get a cup of tea, sit down
and
r
ead through these instructions carefully.
^^^^And for good measure my sec
ond tip is that you will need
t
he following tools to assemble this product, so gather them to
hand before you start.^^^^
B
e
f
o
r
e
y
ou
s
t
a
r
t
PZ3
6.5
mm
Warnings
Failure to follow the warnings could result in serious injury.
Do'
s
To cl
ean wipe with a sponge and warm soapy water.
Do not overtighten screws or bolts.
Due to the size of this pr
oduct we recomm
end that it is
assembled in the room intended for use
.
Unwrap all packaging materials
and place the com
ponents
on top of the carton box or on a cl
ean floor to prevent it from
scratching.
Check the pack
and make sure you have all the parts listed
.
Do not use power tools to construc
t this pr
oduct.
Assembly to be carried out by a competent adult only.
During assembly children should be kept away from the
product
due to possible risk of injury.
Ensure that this pr
oduct is fully assembled as illustrated
and
t
hat all fittings are tight
ened properly before use.
This pr
oduct has been desi
gned for use by a "maximum of
one person at a time"
.
This pr
oduct should only be used on firm, level gr
ound
.
Make sure the legs remain in contact with the gr
ound
.
During assembly k
eep small parts out of reach of children
.
Check all screws or bolts are tightened and inspect r
egularly.
Do not use scourers, abrasives (including washing
powders), bleach or solvent based cleaners as they can
bleach or dam
age the product.
The cot bed is carefully desi
gned for baby's safety and
features an adjustable height base so you can easily reach
baby in the early months.
The cot can be converted to a
bed by separating the split
end
panels and using the top sections as the headboard and
foot
board
.
The cotbed is suitable from approximately 0 months to 36
months
.
Do not place this pr
oduct
near
heat source, windows and
other furniture.
Do not use this pr
oduct if any part is broken, torn or missing
and use only spare parts approved by Tesco Stores Ltd.
Be aware of the risk of
open fire
and other source of str
ong
hea
t, such as electric bar fires, gas fires, etc. in the
near
vicinity of the cot.
Do not leave anything in the cot or place the cot close to
another pr
oduct, which could provide a foothold or present a
danger of suffocation or strangulation, e.g. strings
,
blind/ curtain cords, etc
.
Do not use more than one mattress in the cot.
The thickness of the mattress shall be such tha
t the internal
height (surface of the mattress to the
upper
edge of the
cot frame) is at least
500mm in the lowest position of the cot
base and at least 200mm in the highest position of the cot base
.
The cot bed is suitable for a mattress of
1350 mm in length
and 635 mm in width, or no less than a size of
1400 mm x 680 mm
.
All assembly fittings s
hould always be tight
ened properly
and
fittings should be checked regularly
and retightened as
necessary
.
To prevent injury from falls, w
hen the child is able to climb out
of the co
t, the cot shall no l
onger be used for that child. The
cot should be converted to a bed
.
Children are likely to play, bounce, jump
and climb on
beds,
therefore the child's bed s
hould not be placed too close to
other furniture or windows, blind cords, curtain pulls or other
strings or cords
. It should be placed either tight to any wall or
have a gap of
300mm between the wall and the side of the
bed
.
The
bed can be carefully dismantled for stor
age or
transportation
.
Designed and m
anufactured to BS EN 716:2008 and
BS 8509:2008 + A1:
2011
1 hou
r
Tradesman's tip
s