Terratek T12VCS User Manual
12V Li-ion Cordless Circular Saw
T12VCS
User Manual — Please read and retain for future reference.
IMPORTANT: Read all instructions before use.
Contents
Parts List
Parts List
Safety Instructions
Technical Information
Using your tool
Maintenance
Warranty
1
No. Description No. Description
1 hexagonal screw M6X16 27 spring washer 10
2 upper clamp 28 small gear
3 saw blade 29 motor
4 lower clamp 30 right housing
5 screw ST2.6x10 31 rear cover
6 clamp for blade guard 32 screw st2.6x14
7 lower blade guard 33 left housing
8 screw m5x16 34 bearing 6800
9 torsion spring 35 output shaft
10 retainer ring 36 on/off switch
11 screw ST3x16 37 lock plate
12 Upper blade guard 38 output gear
13 pin 6x28 39 wave washer 11
14 spindle locker 40 bearing 606
15 retainer spring 41 screw m3x8
16 base plate 42 spring washer 3
17 bolt m6x12 43 gear box cover
18 wave spring washer 5 44 safe button
19 angle bracket 45 spring 5.2x23.1
20 rivet 5x6 46 screw st3x14
21 washer 6.4x12x1 47 screw st2.2x10
22 angle knob 48 connector holder
23 bolt m6x14 49 12v li-ion battery pack
24 depth bracket 50 12v fast charger
25 depth lock spanner 51 hexagonal wrench
26 Nut M6
2
Exploded Assembly Diagram
NOTICE: Actual product may vary from pictures shown.
3
1
2
5
6
7
8
9
10
4
3
fig.1
fig.2
1. Battery pack
2. Handle
3. Switch & Safety lock
4. Spindle lock
5. Angle Locking Knob
6. Base plate
7. Lower Guard
8. Cutting depth locking lever
9. Charger
10. Blade screw
Tabs
Charge indicator
Battery capacity indicator LED
4
Technical Information
Model: T12VCS
No-load Speed: 4800 /min
Arbor Size: 10mm
Saw blade: Diameter 100mm
Max. Cutting capacity: 90
o
: 26mm; 45o: 14mm
Battery Type: 1300 mAh Li-ion
Charger
Charging time: 1 hour
Input: 100-240V AC, 50 – 60 Hz, 27W
Output: 12.6V DC, 1500mA Max
Read this entire manual before using this product.
Failure to do so can result in serious injury. Save this manual
for future reference.
Copyright© 2013 by ACL Group (Intl) Ltd. All rights reserved. This manual or any artwork
contained herein must not be reproduced in any shape or form without the express written
consent of ACL Group (Intl) Ltd. Diagrams within this manual may not be drawn
proportionally. Due to continuing improvements, actual product may differ slightly from the
product described herein.
5
Read and Keep This Manual
Please read carefully all instructions within this manual. Failure to follow all safety warnings
can result in serious personal injury. The term “Power Tool” in all of the following warnings
refers to your mains operated (corded) or battery operated (cordless) power tool.
This symbol is to warn you of potential personal injury
hazards. Please read carefully the notes along side this warning
to avoid possible injury or death.
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you
to lose control.
Important SAFETY Information
General Safety Rules
Work area safety
WARNING! Read all instructions. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
The term “power tool” in all of the warnings listed refers to corded or
cordless power tools.
6
Personal safety
Power tool use and care.
Keep your power tool clean and well serviced at all times.
Never adjust or service any power tool before disconnecting from the mains electricity supply.
Always use the correct tool for the job.
Never force the tool to work harder than it is designed to do.
Never use your power tool with broken parts such as switches, guide fences or leg stands.
ALWAYS keep your power tools away from children.
Keep cutting tools sharp to ensure less stress on the motor.
Only have your power tool serviced by a qualified repair agent using manufacturers
recommended parts.
Before use, ensure that the power outlet you are using matches the plug on your power tool
and that the voltage of the outlet matches that of your power tool.
Only use grounded extension cords with power tools fitted with 3 pin plugs and if using
outdoors ensure any extension cord is suitable for outdoor use.
Always try to avoid body contact with grounded surfaces, such as radiators, cooking ranges
and any other fixed appliance with metal surfaces.
Do not expose your power tool to wet or damp conditions and NEVER use in rain.
Check regularly the power cord of your machine and any extension cord that you are using
for damage.
Do not carry or pull the machine with the power cord.
Ensure the cord is clear from hot surfaces, oil or sharp objects.
Never use your power tool whilst under the influence of alcohol, drugs or medication.
Tiredness can often cause accidents, stay alert.
Never use your power tool without the correct guards in place.
Always use approved eye protection and dust mask. Non slip safety shoes and hearing
protectors should be worn at all times when using your power tool.
Ensure any dust collecting device supplied with your machine is connected correctly before
use.
Ensure all loose clothing, long hair or jewellery is kept clear of the machine.
Before plugging your power tool into the power outlet ensure the power tool is in the OFF
position.
Check that wrenches or adjusting keys have been removed. Any wrench or key left attached
to a moving part can result in injury.
Electrical safety
Loading...