Terrano XT User Manual

For easy reference while on the road, download the Pocket Guide from terranosystems.com/support/.

This is version 1.0 of the TERRANO XT Manual. The latest version of the manual in your preferred language and
various tutorials can be found at terranosystems.com/support/.

2

CONTENTS

1. Introduction 4

2. Charging the TERRANO XT 5

3. Getting Started 6

3.1 Getting to Know Your TERRANO XT 6

3.2 Switching Your Unit On/Off 6

3.3 Different W ays t o O perate Your TERRANO XT 6

3.4 Basic Functions 7

3.5 Pairing Your Unit to Bluet ooth Devices 7

4. On the Road 9

4.1 Making and Receiving Phone Calls 9

4.1.1 Making Phone Calls 9

4.1.2 Answeri ng Phone Calls 9

4.1.3 Rejecting Phone Call s 9

4.1.4 Ending Phone Calls 9

4.1.5 Toggling Between Calls on T wo Mobile Phones Pai red to Your Uni t 9

4.1.6 Disc onnec ting the Current Call and Switchi ng To the Second Call 9

4.2 Bluetooth Intercom 10

4.2.1 Pairing the Bluetooth Interc om to other Ter rano Units 10

4.2.2 3-Way and 4- Way Bluetooth Intercom Calls 10

4.2.3 Using the Bluetooth Interc om 11

4.3 Listening to Music and Radio 14

4.3.1 Listeni ng to Mus ic 14

4.3.2 Listeni ng to FM Radio 15

4.3.3 Sharing Mus ic and Radio 16

5. Personalizing Your Device 17

5.1 Setting t he Def ault Mobile Phone 18

5.2 Using Parallel Audio Streaming 18

5.3 Audio Source Priorities 19

6. Troubleshooting 20

6.1 Soft Reset 20

6.2 Reset Pairing 20

6.3 Reset to Factory Sett ings 20

6.4 FAQ 20

7. Support 21

8. Glossary 22
Appendix A. TERRANO XT Modes and Events - LEDIndications 23

3

1. INTRODUCTION

Thank you for choosing the TERRANO XT Bluetooth® communication system for bicycle helmets.

This manual describes the features of your TERRANO XT and how to use them.

We wish you a great TERRANO XT experience and encourage you to write to us at

[e-mail] regarding any questions, suggestions or comments you may have.

If you have not yet installed the TERRANO XT unit in your helmet, please install it as described in the Installation
Guide provided in the package.

4

2. CHARGING THE TERRANO XT

Make sure that your TERRANO XT battery is charged for at least 4 hours before initial use.

To charge the TERRANO XT:

● Using the supplied USB cable, connect your computer or wall charger to the TERRANO XT USBport.

● Charging with the wall charger is faster than via a computer USB port.

● Charging your unit switches it off automatically. To use your unit while it is being charged, switch it on.

(see Switching Your Unit On/Off on page 6).

● You can charge the unit while riding using a power bank.

During charging, the LED indicates charging status as follows:

● Red LED on - charging

● Red LED off - charging complete

If the battery level reaches 20%, a battery status voice announcement warns you that your battery is low.

5

3. GETTING STARTED

3.1 GETTING TO KNOW YOUR TERRANO XT

3.2 SWITCHING YOUR UNIT ON/OFF

To switch your unit on:

● Press and for 1 second.

The speaker plays an ascending tone and a voice message "Hello TERRANO XT".

In all battery states, the LED flashes blue three times repeatedly, confirming that your TERRANO XT is on.

To switch your unit off:

● Tap and .

In all battery states, the LED flashes red three times repeatedly, confirming that your TERRANO XT is
switching off. The speaker plays a descending tone and a voice message "Goodbye".

Connecting your unit to a charger switches off the unit.

3.3 DIFFERENT WAYS TO OPERATE YOUR TERRANO XT

You can operate the various features by any of the following methods:

● Pressing a button or combination of buttons on the unit.

● Using the Voice-Assisted Menu in combination with either unit buttons or with the VOX (voice activation).

VOX is for hands free operation of your TERRANO XT. You can say a word or phrase loudly when the voice­assisted menu reaches the function you want to use and your TERRANO XT performs that function.

LEDs, tones and voice announcements guide you while using the functions of your TERRANO XT, as described
in TERRANO XT Modes and Events - LEDIndications on page 23.

This manual describes the most direct method to operate each feature.

6

3.4 BASIC FUNCTIONS

To turn the volume up for current audio source:

● Tap .

With each tap, a louder tone is played on the speaker until you reach the maximum volume, as indicated by
the maximum volume tone.

To turn the volume down for current audio source:

● Tap .

With each tap, a quieter tone is played on the speaker until you reach the minimum volume, as indicated by
the minimum volume tone.

To mute the microphone completely and lower the speaker volume to the minimal level when an audio
source is active:

● Tap and .

A descending tone is played on the speaker.

3.5 PAIRING YOUR UNIT TO BLUETOOTH DEVICES

Your TERRANO XT has two Bluetooth channels for connection to Bluetooth devices such as mobile phones,
GPS devices and Bluetooth music players with A2DP.

To connect your TERRANO XT to a Bluetooth device, you must first pair them while in Standby (see TERRANO

XT Modes and Events - LEDIndications on page 23). Once paired, they automatically recognize each other

whenever they are within range.

To pair Bluetooth channel 1 to a mobile phone:

1. Enable Bluetooth on the mobile phone.

2. Press for 5 seconds.

The LED flashes red and blue.

3. On your mobile phone, search for Bluetooth devices as described in your phone's instructions.

4. When your TERRANO XT appears in the list of available devices, select it.
If prompted for a PIN or Passkey, enter 0000 (four zeros).

The phone confirms that pairing has succeeded and the LED flashes purple for 2 seconds.

To pair Bluetooth channel 2 to another Bluetooth device:

1. Enable Bluetooth on the device (such as mobile phone, GPS device, music player).

2. Press for 5 seconds.

7

The LED flashes red and blue.

3. Tap twice. The LED starts flashing red and green.

If you are pairing a GPS device, make sure you perform the next step.

4. If you are pairing a GPS device, tap .

The LED flashes slower.

5. On the device you are pairing, search for Bluetooth devices (as described in its instructions).

6. When your TERRANO XT appears in the list of available devices, select it.
If prompted for a PIN or Passkey, enter 0000 (four zeros).

The device confirms that pairing has succeeded and the LED flashes purple for 2 seconds.

● If pairing is not completed within 2 minutes, the unit automatically returns to Standby.

● If you have paired two different mobile phones directly to your TERRANO XT, set one as default for

making calls (see Setting the Default Mobile Phone on page 18).

● Not all Bluetooth mobile phones broadcast Bluetooth Stereo music (A2DP), even if the phone has an MP3

player function. Consult your mobile phone’s user manual for more information.

● Not all Bluetooth GPS devices allow connection to Bluetooth audio devices. Consult your GPS User

Manual for more information.

To cancel the pairing process:

● Press for 2 seconds.

● The LED stops flashing red and blue or red and green.

To reset all Bluetooth device pairing:

● Press and for 5 seconds.

In all battery states, the LED flashes purple slowly five times, confirming that pairing has been reset.

Resetting all Bluetooth device pairing also resets all Bluetooth intercom pairing.

8