Page 1
LF-30S
Owner’s Manual
Limited Warranty
Audiovox Corporation (Audiovox) warrants this product against
defects in materials or workmanship for one (1) year from the
date of purchase. During this period, this product will be
replaced without charge. This warranty does not cover any
damage due to acts of nature, commercial use, accident, misuse,
abuse or negligence. This warranty is only valid in the USA.
Replacement as provided under this warranty is the exclusive
remedy of the consumer. Audiovox shall not be liable for any
incidental or consequential damages for breach of any express
or implied warranty on this product, except to the extent that
limitations of this sort are prohibited by applicable law.
THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURCHASE EXCEPT TO THE EXTENT
THAT IMPLIED WARRANTIES OR EITHER SORT ARE REQUIRED BY
APPLICABLE LAW, AND IN SUCH CASE, EACH WARRANTY IS
LIMITED IN DURATION TO THE ONE YEAR.
LF-3OS
Wireless A/V Transmitter and
Receiver System
TERK and the TERK logo are registered trademarks of AUDIOVOX Corp. 97P007A
For customer service and
technical information:: 1.800.290.6650
Page 2
2
Introduction
TERK LF-30S - 2.4GHz Wireless Convenience
The TERK LF-30S uses the latest in wireless technology to deliver
consistently sharp and clear video images and stereo audio up to
150 feet away.
By transmitting at a super-high frequency of 2.4 GHz,
the FCC-approved LF- 30S avoids the crowded frequency band
used by many cordless phones and other wireless A/V
transmitters, and utilizes FM rather than lower quality AM signal
modulation. The use of state-of-the-art circularly polarized
directional transmitting and receiving antennas maximizes signal
range and minimizes interference from unwanted signals.
The LF-30S is compatible with all types of TVs, both new and old,
and A/V components. You can even add more receiver units
(Model LF-30RX, sold separately) to accommodate additional TVs
or A/V components and expand your home entertainment system.
LF-30S
1
Important Safety Precautions:
1. To prevent fire or shock hazard, do not expose this product to
rain or moisture. Do not use near a bathtub, wash bowl, sink or
laundry tub, in a wet basement or around a swimming pool.
2. To avoid electrical shock, do not open the case of
this product.
3. Operate this product using only the power supply included with
the unit or supplied as an accessory.
4. Do not overload electrical outlets or extension cords as this can
result in electrical shock.
5. Refer servicing to qualified personnel only.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
Disclaimer: This product is designed for lawful use as a wireless
system for transmitting audio and video signals from one location
in the home or office to another location. Audiovox Corporation
hereby advises the consumer to consult with local officials and
other legal authorities regarding the proper use and application of
this product in compliance with all applicable state and federal
laws. Audiovox Corporation shall not be responsible for any
misuse or unlawful application of this product by any individual or
entity under any circumstances.
LF-30S
Page 3
4
Package Contents
The following items are included in the LF-30S box. Please check
that they are all present before discarding the box and beginning
the installation.
1 - LF- 30S Transmitter (Model LF-30STX)
Sends wireless A/V signals to the receiver
1 - LF- 30S Receiver (Model LF-30SRX)
Receives wireless A/V signals from the transmitter
2 - Audio/Video (A/V) cables
Connects the transmitter and receiver to your TV sets and/or
A/V components
2 - Power adapters
Provides 9V DC power to the transmitter and receiver
1 - Coaxial cable with two “F” connectors
1 - IR Extender
2 - Mounting Brackets
4 - Adhesive Strips
LF-30S
3
Introduction (continued)
The LF- 30S gives you the convenience to wirelessly:
• Watch cable, satellite programming or DVD movies on any TV in
your home, without the hassle and expense of running extra
wiring, moving your A/V source or buying another one.
• Set up a TV anywhere inside or outside your home (where you
have access to an AC outlet).
• Listen to stereo music on powered speakers inside or outside
the home.
Remote Control Extension Function:
• Control the A/V source from the remote TV’s location using the
A/V source’s remote control.
• 4 channel frequencies lets you choose between channels for
best reception.
LF- 30S gives you safety and security:
• Monitor your baby or children on any TV in your home using your
camcorder or a miniature CCD security camera.
• See who is outside your door, in the backyard, on the playset or
in the pool.
Simply connect the transmitter unit to any A/V source component
you want to view or hear at another location, and then connect the
receiver unit to the TV or powered speakers in that location.
LF-30S
Page 4
6
LF-30S
5
Controls and Features
The transmitter and receiver units look virtually alike but are
labeled accordinly on the front of the units. However, the receiver
can also be identified by the threaded RF coax connector labeled
“TO TV” on the back panel.
A - Directional 2.4GHz antenna (both units)
Sends and receives A/V signals.
Caution: Do not attempt to rotate the antenna a full 360 degrees,
or permanent damage to the antenna and mechanical stopper
will occur.
B - Channel Selection Switch (both units – underneath unit)
Both the transmitter and the receiver must be set to the same
channel for proper operation.
C - On/Off Switch (both units)
Turns the transmitter and receiver on or off.
D - 9V DC Power Port (both units)
Both adapters are the same and are interchangable.
E - Audio/Video Jacks (both units)
Right and left stereo audio (red/white) jacks and a composite
(yellow) video jack are used for connection to A/V components
and/or TV sets.
F - RF Connector (receiver only)
Used to connect the RF output from the receiver unit to the RF
input of a TV set.
G - Channel 3/4 Video Selector Switch (receiver only –
underneath unit)
Set the output of the receiver unit to either channel 3 or 4, to
correspond to the TV channel you wish to watch the A/V source
video on.
H - IR Extender Jack (transmitter only)
Allows you to remotely control the A/V source that is
connected to the transmitter.
I - Antenna (both units)
Sends and receives remote control signals.
J - Antenna In
LF-30S
G
Page 5
8
VCR users:
If you want to view your VCR on a TV located near the transmitter,
connect a coaxial cable (not supplied) from the CABLE/ANT OUT
(or OUT TO TV) on the VCR to the CABLE/ANT IN port connector
on your TV.
LF-30S
7
Connecting the Transmitter to a
Video Component
Connecting the transmitter to a video component such as a DVD
player, satellite receiver, VCR, PVR or camcorder.
1. Make sure the transmitter’s On/Off switch is “Off.”
2. Connect one set of red, white and yellow A/V cables from the
A/V jacks on the back of the transmitter to the LINE OUT A/V
jacks on the back of the A/V device.
Be sure the red, white and yellow plugs on the A/V cables match
the red, white and yellow jacks on both the transmitter and the
A/V device.
If the A/V device has only one output for audio (mono sound only);
connect the white plugs on the cable to that single audio output
and to the transmitter’s AUDIO LEFT jack.
3. Plug the small end of the power adapter into the back of the
transmitter and the other end into a standard A/C wall outlet.
Turn the On/Off switch to the “On” position.
4. Make sure the receiver and transmitter units are set to the
same channel.
5. Locate and orient the transmitter unit according to the
“Orienting the Transmitter and Receiver Units” (page 14)
section of this manual.
LF-30S
Page 6
10
Connecting the Transmitter to
Audio Components
To enjoy sound from your CD player, cassette deck or other audio
component in another room, you can connect the transmitter
directly to that component. To use this feature, you must connect
either powered speakers, another stereo receiver, or an amplifier
to the receiver at the remote site.
1. Make sure the transmitter’s On/Off switch is “Off.”
2. Connect one set of A/V cables from the red and white AUDIO IN
jacks on the back of the transmitter to the LINE OUT audio
jacks on the back of your audio component. Be sure the red and
white plugs on the A/V cables match the red and white jacks on
both the transmitter and audio component. (The yellow video
plugs will not be used.)
3. Plug the small end of the power adapter into the back of the
transmitter and the other end into a standard A/C wall outlet.
Turn the On/Off switch to the “On” position.
4. Make sure the receiver and transmitter units are set to the
same channel.
5. Locate and orient the transmitter unit according to the
“Orienting the Transmitter and Receiver Units” (page 14)
section of this manual.
LF-30S
9
Connecting and Using
the IR Extender
The IR extender allows you to remotely control the A/V device
that is connected to the transmitter from the room you have the
receiver located in.
Connecting the IR Extender:
1. Extend the thin antenna upwards.
2. Plug in the IR extender into the connector on the back of
the transmitter.
3. Extend the IR extender cable to the front of the A/V device that
is connected to the transmitter.
4. Locate the IR window (dark, nearly opaque plastic) on the A/V
device connected to the transmitter. Look into the window and
try to locate the IR receiver behind the plastic.
5. Remove the adhesive pad on the IR extender and adhere it to
the window in front of the IR receiver on the A/V device
connected to the transmitter.
Controlling the A/V device remotely with your remote control:
Operate the A/V source’s remote control (the A/V device that is
connected to the transmitter) as you normally do while pointing
it at the receiver. The receiver wirelessly sends the infrared
command to the transmitter which then transmits it via the IR
extender to the A/V source device.
If you are having difficulty controlling the A/V device make sure
that you verify that your IR extender is positioned correctly in front
of the IR emitter on the device.
LF-30S
Page 7
12
LF-30S
11
Connecting the Receiver to a TV
After connecting the transmitter to your A/V source, you must
connect the receiver to a TV or another component.
There are two ways to connect the LF-30S Receiver to a remote TV
(a TV in a remote location away from the A/V source):
1 - Connected directly to the remote TV
2 - Connected directly to a VCR, which is then connected to the TV
Note: If your TV has picture-in-picture (PIP) capability, you can
also view any image sent by the transmitter (such as a sleeping
baby monitored by your camcorder) in the small inset picture
while enjoying other programming on the rest of the screen.
Consult your TV owner’s manual for instructions on using its
PIP feature.
1. Make sure the receiver’s On/Off Switch is “Off.”
2. Connect one set of red, white and yellow A/V cables from the
A/V jacks on the back of the receiver to the LINE IN A/V jacks
on the back of the TV.
If your TV has A/V jacks (red, white and yellow for a stereo TV
or only white and yellow jacks for a mono TV), connect one end
of an A/V cable to the TV’s A/V jacks and to end of the cable to
the receiver.
Be sure the red, white and yellow plugs on the A/V cables match
the red, white and yellow jacks on both the receiver and the TV.
If your TV has only one input for audio (mono sound only), connect
the white plugs on the cable to that single audio input and to the
receiver’s AUDIO LEFT jack. If your TV does not have A/V jacks,
use a coaxial cable to connect the RF output jack of the receiver to
the coaxial input of the TV.
Note: If you already have an antenna or cable connected to your
TV, use an A/B switch or modulator (not included) and additional
coaxial cables to connect the receiver.
3. Plug the small end of the power adapter into the back of the
receiver and the other end into a standard A/C wall outlet. Turn
the On/Off switch to the “On” position.
4. Make sure the receiver and transmitter units are set to the
same channel.
5. Locate and orient the transmitter unit according to the
“Orienting the Transmitter and Receiver Units” (page 14)
section of this manual.
LF-30S
Page 8
14
Orienting the Transmitter and
Receiver Units
The LF-30S system broadcasts video and audio using the square
directional antennas and your remote control signals using the
whip antennas.
For optimum performance, both the transmitter and receiver
antennas should be carefully oriented towards each other, and the
whip antennas should be positioned vertically.
IMPORTANT: The square antennas are directional antennas – the
side of each ant
enna with the molded pattern see fig. below)
should face towards each other.
For best performance, the units should be placed as high as
possible to minimize the possibility of interference from people
walking between the transmitter and receiver.
Both the LF- 30S Transmitter and Receiver should be placed on a
flat, stable surface to prevent damage from falling.
For maximum range between the transmitter and receiver units,
try to minimize the number of obstacles between the transmitter
and receiver units, such as your TV, other electronics, large
furniture or appliances.
Note: Although the antennas have been designed to pivot, they
have limited rotation in either clockwise or counter-clockwise
directions. Do not try to force the antennas to move beyond their
range of motion or permanent damage may result. Under no
circumstances should you try to fully rotate the antennas.
Always make sure the receiver and transmitter units are set to the
same channel.
LF-30S
13
Connecting the Receiver to
Powered Computer Speakers
Since the LF-30S only receives stereo audio signals and does
not amplify them; the speakers you use to listen to wireless
sound must be self-powered or attached to an amplifier or
stereo receiver.
1. Make sure the receiver’s On/Off Switch is “Off.”
2. Connect the speaker input cable from your powered speakers to
a “Y adapter” mini phone jack adapter (3.5mm to stereo RCA
plug - not included).
3. Connect the red and white plugs of the “Y” adapter to the red
and white audio jacks of the receiver.
4. Plug the small end of the power adapter into the back of the
receiver and the other end into a standard A/C wall outlet. Turn
the On/Off switch to the “On” position.
5. Make sure the receiver and transmitter units are set to the
same channel.
6. Locate and orient the transmitter unit according to the
“Orienting the Transmitter and Receiver Units” (page 14)
section of this manual.
LF-30S
Panel detail showing
“Pattern Side” as it appears
on one side of each
directional panel
Important:
The moulded texture
side of each antenna
should face each
other
Page 9
Page 10
18
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to providereasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This
equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator & your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
LF30
17
Government Approvals
USA – This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and
the receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
assistance.
Canada – This device complies with RSS-210 of Industry Canada.
Operation is subject to the following conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
LF-30S
Loading...