Tennsco WBD-1 User Manual
ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1420908
STACKABLE DRAWER UNIT
Model WBD-1
Tennsco Corp., Dickson, TN 37056-1888 * (615) 446-8000
READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO
ASSEMBLE YOUR Tennsco STACKABLE DRAWER UNITS.
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!
DESCRIPTION
Tennsco
The
which may be stacked on top of a bench or mounted
underneath. Drawers come equipped with adjustable
divider, removable parts tray, nylon roller bearings for ease
of operation and aluminum drawer pulls, padlock hasp and
knock out for optional cam lock (order CL-1 separately).
Mounting brackets for attaching to steel top are included.
stackable drawer unit is a self-contained unit
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE mu st be taken
when handling various pieces to avoid injury. For safety,
wear a pair of work gloves when assembling or performing
any maintenance on workbench.
SPECIFICATIONS
Overall Dimensions
Housing........................................15"w x 18"d x 8
Drawer.................................... 13"w x 16
Tray............................................. 12
Basic Construction
Drawer and housing...............20 to 24 gauge steel
Track and rail...................................18 gauge steel
Mounting brackets...........................14 gauge steel
Tray...............................................Black Polymer
Weight.................................................................24 lbs.
Colors .........................Medium Grey, Light Grey, Sand
1
⁄
2
1
⁄
"w x 7
"d x 6
2
1
⁄
"d x 1"h
2
1
⁄
"h
4
3
⁄
"h
8
Step By Step Installation Instructions
(Refer to figures at right)
Tools required: Slotted screwdriver, Phillips screwdriver, and 7/16" wrench or nut driver.
ASSEMBLY FOR STEEL TOP:
1.
Remove drawer (Ref. No. 1) from housing (Ref. No .
2) by first pulling it to the full extent that the
suspensions allow. Once the drawer is fully open,
move the plastic lever inside the suspension member
to release the suspension sections. (On one side of
the suspension you will need to move the leve r up;
on the opposite side, you will need to move the lever
down.)
2. Secure one mounting bracket (Ref. No. 3) to left side
of housing with two 1/4"-20 bolts and nuts.
NOTE:
Mounting brackets are sold seperately. On 30" deep
top, the bracket should extend 10
on 36" deep top, it should extend 16
3. Attach second mounting bracket to welde d nu t in
of housing only
with one
1
1
" behind housing;
⁄
2
1
".
⁄
2
"-20 bolt. Do not tighten
⁄
4
rear
yet, as having the bracket loosely attached simplif ies
mounting to the workbench top.
4. To attach drawer asse mbly to workbench top, insert
back end of the left drawer bracket diagonally into
flange on the rear underside of the top. Then, slide the
front of the bracket into the fron t flange until drawer
assembly is aligned evenly with front of workbench top.
5. Insert the back end of the loosely attached right drawer
bracket into the flange on the rear underside of the
workbench top. Then, slide the front of the bracket into
the front flange until bracket is aligned evenly with front
of workbench top.
6. Align holes in mounting brackets and top in desired
location and secure, using four
1
"-20 bolts and nuts.
⁄
4
7. Attach front end of bracket to front of housing using one
1
"-20 bolt and nut. Secure the rear bolt and nut which
⁄
4
was left loose in step 4.
9. Insert drawer into housing.
ASSEMBLY FOR WOOD TOP:
1. Remove drawer (Ref. No. 1) from housing (No. 2) by
first pulling it to the full extent that the suspensions
allow. Once the drawer is fully open, move the plastic
lever inside the suspension member to release the
suspension sections. (On one side of the suspension
you will need to move the lever up; on the opposite side,
you will need to move the lever down.).
2.Using housing as template, mark location of four holes
for wood screws onto underside of wood top.
(Recommendation:
1
" offset from front of bench top.)
⁄
2
(Note: mounting brackets are not used when installing
on a wood top.)
about
5
" drill bit, drill holes into wood top, drilling
⁄
32
1
3
" to
⁄
2
" deep.
⁄
4
3
" hex head
⁄
4
3. Using
4. Secure housing to top, using four #14slotted wood screws.
5. Insert drawer into housing.
ASSEMBLY FOR DRAWER TO DRAWER:
1. Remove drawer (Ref. No. 1) from housing (No. 2) by
first pulling it to the full extent that the suspensions
allow. Once the drawer is fully open, move the plastic
lever inside the suspension member to release the
suspension sections. (On one side of the suspension
you will need to move the lever up; on the opposite side,
you will need to move the lever down.).
2. Bolt housing together with four
1
"-20 bolts and nuts.
⁄
4
3. Insert drawer into housing.
Loading...