Tennsco Single Tier Lockers Three Wide User Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1060702

UNASSEMBLED SINGLE TIER LOCKERS

Tennsco Corp., Dickson, TN 37056-1888  [phone]

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!

Tennsco single tier lockers are designed for use by
single individuals for the security of clothing and
personal property. One- or three- wide units are
available in 60" or 72" heights, with or without legs.
Optional opening sizes are 12", 15", 18", or 24" wide by
12", 15", 18", 21", and 24" deep. Heavy gauge steel
construction with baked on enamel finish assures years
of trouble free service, even under the most demanding
situations. All units have a top shelf and three coat
hooks in each compartment; units 18" deep and deeper
provide a coat rod. Doors are equipped with painted
locking channels which are completely cushioned for
silent operation, as well as recessed handles that allow
the use of standard size padlocks, built-in key locks
and combination locks ( all optional ) for a flush, clean
appearance.

THREE-WIDE UNIT

Basic Construction:

All models are constructed of 16 gauge steel frames
and doors with a 24 gauge door stiffener and 24 gauge
body components. Locking channels are 20 gauge with
baked on enamel finish with quiet-action spring loaded
latches. Recessed handles are black painted steel.
Doors are louvered for ventilation.

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken
when handling various pieces to avoid injury. For safety,
wear a pair of work gloves when assembling or performing
any maintenance on lockers.

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment,
hereunder. This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification
or repair by persons not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced,
modified or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS

AT SELLERS OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR

OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers
place of business or require Buyer to return the goods to Seller for inspection on Sellers premises. Transportation charges covering returned goods will
be borne by Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.

LIMITED WARRANTY

TENNSCO Corp., P.O. BOX 1888, DICKSON, TN 37056-1888

[phone] or [phone] (toll free)

Website: www.tennsco.com E-mail: [e-mail]

PK-1760702

ASSEMBLY OF SINGLE TIER LOCKERS -- THREE WIDE UNIT

Assemble lockers individually or in groups of three. Do not tighten bolts until unit is
completely assembled. Tools required: 11/32" nut driver (11/32" socket may be substituted)

1. Place back on a protected flat surface so

that the flanges are upward. If available use
a pair of "Saw Horses" to assemble units
on for easier installation.
Refer to Figure 2 for

Top

reference numbers.

Two holes for rear legs.

Bottom

Back

2. Bolt left side

(Ref. No.2)
to the back
so that side
flange fits
around back.

5. Bolt right side (Ref. No.7)

to the back so that
side flange fits
around back
and also
attach
to top,
bottom
and shelf.
Attach remaining
coat hook.

Left side

Intermediate side

Intermediate side

Right side

Do not bolt
through the
rear leg
holes yet.

Left side

Back

3. Bolt shelf (Ref. No.4) to back and side place

coat hooks (Ref. No.5) as shown. (For lockers
18" and deeper, bolt shelf in place and and
then attach side coat hook through
third and fourth holes
below shelf). Attach
top and bottom to
side and back
as shown.

Left side

Back

Bottom

Shelf

Top

6. If the locker has legs, insert

the leg into the corner
between the bottom and the
side. Bolt the leg to the
side using two
#8-32 x 1/2
bolts and
#8-32
nuts.

7. Place door and

frame assembly
(Ref.Nos. 8 & 9)
over the locker
body/bodies and
secure with bolts
and nuts. Make
certain that body
sides are inside
frames --

never
between frames
on multiple units.

Door & Frame assembly

4. Repeat steps 1, 2 and 3 to assemble second

and third sections. Make certain that coat
hooks are attached on each side panel
surface. A right side or left side can be used
as an intermediate side. Save one right side to
be used in step 5.

Leave out a few bolts
in the outer frames to
be used to attach adjoining units.