Tennsco Single Tier Lockers One Wide User Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1050702

UNASSEMBLED SINGLE TIER LOCKERS

SINGLE WIDE UNIT

Tennsco Corp., Dickson, TN 37056-1888  [phone]

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!

Tennsco single tier lockers are designed for use by single
individuals for the security of clothing and personal property. One­or three- wide units are available in 60" or 72" heights, with or
without legs. Optional opening sizes are 12", 15", 18", or 24" wide
by 12", 15", 18", 21", and 24" deep. Heavy gauge steel
construction with baked on enamel finish assures years of trouble
free service, even under the most demanding situations. All units
have a top shelf and three coat hooks in each compartment; units
18" deep and deeper provide a coat rod. Doors are equipped with
painted locking channels which are completely cushioned for silent
operation, as well as recessed handles that allow the use of
standard size padlocks, built-in key locks and combination locks
(all optional) for a flush, clean appearance.

Basic Construction:

All models are constructed of 16 gauge steel frames and doors
with a 24 gauge door stiffener and 24 gauge body components.
Locking channels are 20 gauge with baked on enamel finish and
quiet-action spring loaded latches. Recessed handles are black
painted steel. Doors are louvered for ventilation.

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when
handling various pieces to avoid injury. For safety, wear a pair of work
gloves when assembling or performing any maintenance on lockers.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder.
This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification or repair by
persons not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced, modified or removed.
UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS

AT SELLERS OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR

OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place
of business or require Buyer to return the goods to Seller for inspection on Sellers premises. Transportation charges covering returned goods will be borne
by Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.

TENNSCO Corp., P.O. BOX 1888, DICKSON, TN 37056-1888

[phone] or [phone] (toll free)

Website: www.tennsco.com E-mail: [e-mail]

ASSEMBLY OF SINGLE TIER LOCKERS -- SINGLE WIDE UNIT

Assemble lockers individually or in groups of three. Do not tighten bolts until unit is

completely assembled. Tools required: 11/32" nut driver (11/32" socket may be substituted).

1. All reference numbers refer to the illustrations in

Figure 1, the door lock detail, and the chart on
the back cover. This is to help you identify the
various parts as they
are mentioned.

Top

2. Place back

Bottom

Back

the flanges face upward. If

available, place the unit on a pair of
"saw horses" for easier
installation.

Left side

(Ref. No. 1) on a

protected flat surface so that

Back

3. Bolt left side

Do not bolt

through rear

leg holes yet.

(Ref. No. 2) to the
back so that side flange
fits around back.

5. Bolt right side (Ref. No. 7) to the

back so that side flange fits
around back. Also attach
to top, bottom and shelf.
Attach remaining
coat hook.

Right side

Bottom

6. If the locker has legs, insert the

leg into the corner between
the bottom and the side.
Bolt the leg to the
side using two
#8-32 x 1/2
bolts
and
#8-32
nuts.

Top

Bottom

Top

Shelf

Top

Shelf

4. Bolt shelf

(Ref. No. 4) to back
and side. Attach coat
hooks (Ref. No. 5) as shown.

(For lockers 18" and deeper, bolt
shelf in place, then attach side coat
hook through third and fourth holes
below shelf). Attach top and bottom to
side and back, as shown above.

slots

Door & Frame assembly

7. Place door

and frame
assembly (Ref. Nos.
8 & 9) over the locker
body and secure with bolts
and nuts. Make certain that body
sides are inside frames.