Tennsco Shelving with Plywood Beams User Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1991008

Z-Line Record Archive Storage System
Installation Instructions

Tennsco Corp., Dickson, TN 37056-1888 • [phone]

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!

Congratulations on your purchase of
a Z-Line Record Archive Storage
System from Tennsco! Z-Line's
interlocking keyhole design not only
makes installation fast and easy but
eliminates the need for clips,
gussets, sway braces or other
hardware commonly used in
conventional shelving, allowing
completely free access to your
stored materials from all sides of
the unit. And our particleboard
decking recesses inside the deck
supports, reducing the overall profile
for greater storage.

Z-Line Record Archive Storage is
available in 60" and 84" heights, 42"
and 69" widths, and 15" (single
entry) and 30" (double entry) depths.
And starter and adder units allow for
joining shelving units together.

GENERAL SAFETY INFORMATION

Some parts may have sharp edges.
CARE must be taken when handling
the pieces to avoid injury. For safety,
wear a pair of work gloves when
assembling or performing any
maintenance on shelving.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment,
hereunder. This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification
or repair by persons not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced, modified
or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE

GOODS AT SELLER’S OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL

OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers
place of business or require Buyer to return the goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will
be borne by Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.

TENNSCO CORP., P.O. BOX 1888, DICKSON, TN 37056-1888

[phone] [phone]

PK-1991008

ASSEMBLY OF ARCHIVE SHELVING

Tool Needed: A rubber mallet for seating the shelf supports into the uprights.

Two people are recommended for assembly. Approximate assembly time: 15 to 30 minutes per section.

1. The reference numbers used throughout this

sheet refer to the illustration on the back cover.
This is to help you to identify the various parts
as they are mentioned.

2. Depending upon

whether you ordered
a single unit or an
adder unit, you may
have one or both of
the styles of upright
shown at right:

A single unit will use EUR posts for all four
uprights, as shown below in Figure A. If you plan
on installing an adder unit, however, you should
build your starter unit with two ZTP
posts on one end
(which will join
with the adder),
as shown in
Figure B.

A. Single unit with

four Angle Posts (EUR).

Angle

Post (EUR)

"T" Post

(ZTP)

4. Repeat the instructions in step 3 to construct a

second set of unit ends.
NOTE: If you are planning to install an adder
unit, this second set of
uprights should consist
of ZTP uprights
(Ref. No. 1b)
so that
adjacent
sections can
be tied
together.
Carefully
review step 2
and step 9
to better
understand
this.

B.

Two or more units with Angle Posts (EUR) on each

end and "T" Posts (ZTP) as intermediate uprights.

3. With help from an associate, or using a wall for

support, connect two EUR uprights (Ref. No. 1a)
using two front-to-back supports (Ref. No. 2), one
at the top and one near the bottom (you should
leave the bottom-most
keyhole slot empty).
Be sure the
front-to-back
supports are
fully seated
in the key­hole slots,
as shown.
NOTE: The
uprights must
be positioned
so that the
narrow part
of the slots
is toward the
floor, as shown
in the inset at right.

NOTE: Inset is shown

from opposite side.

IMPORTANT: Support
MUST be inserted so
the flat surface is on
top as shown in pro­file at left!

5. With the help of an associate, connect the two

unit ends with left-to-right shelf supports (Ref.
No. 3). Again, be
sure that
the flat
surface of
the shelf
support is
facing up,
and that
the shelf
supports
are fully
seated,
as was
illustrated
in step 3.