ASSEMBLY INSTRUCTIONS & PARTS MANUAL #2380707
REGAL SHELVING, 36"w x 76"h
RGL -1236S, -1236A, -1536S, -1536A, -1836S, & -1836A
Tennsco Corp., Dickson, TN 37056-1888 • (615) 446-8000
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!
Congratulations on your purchase of Regal
Shelving from Tennsco! Regal shelving is an
attractive and versatile shelving unit designed for
strength - yet attractive enough for the front
office. Featuring particleboard shelves with a
light-oak laminate finish, Regal's shelves are
adjustable in 1
customize for your specific storage needs.
Unlike lesser-made shelving that uses tab connectors, Regal Shelving components snap
together with steel shoulder rivets. This allows
for easy assembly without bolts or nuts, while
providing increased strength - each shelf will
hold up to 600 lbs. Regal's heavy gauge steel
construction with baked on enamel finish assures years of trouble free service, even under
the most demanding situations.
1
/2" increments...allowing you to
An optional sliding divider kit is also available to
help hold materials in place.
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be
taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on shelving.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment,
hereunder. This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification
or repair by persons not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced,
modified or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS
AT SELLER’S OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers
place of business or require Buyer to return the goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will
be borne by Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.
TENNSCO CORP., P.O. BOX 1888, DICKSON, TN 37056-1888
(615) 446-8000 (800) 251-8184
PK-2010707
ASSEMBLY OF REGAL SHELVING
Tools Needed: A rubber mallet is helpful for seating shelf supports. Requires one or two people for assembly.
The first seven steps are easier with two people assembling. Approximate assembly time: 20 to 40 minutes.
1. Unpack all items and carefully compare the
items you received with the packing list on the
back page.
2. Determine whether you will be assembling a
single unit, or multiple units joined together. For
a single unit, use two “L” uprights (Ref. No. 1a).
For multiple units, use one “L” upright and one
“T” upright (Ref. No. 1b).
1a
OPEN “L”
UPRIGHT
1b
OPEN “T”
UPRIGHT
3. Examine the slots on the two uprights which
UP
DOWN
you have selected. When an upright
is standing up on end, the narrow part
of the keyhole slots should be toward
the floor, while the wide part should be
toward the top (see illustration at left).
“L”
UP-
RIGHT
4. After determining which end
of the upright is the bottom,
attach a plastic foot (Ref. No.
4 or 5) to the bottom of each upright
by pressing it into place.
Note, at right, the difference
between a foot for an "L" upright
and a foot for a "T" upright.
5. Lean one “L”
upright against a
wall, and
temporarily place
one shelf support
(Ref. No. 2) at
approximately eye
level to properly
space the uprights.
Make sure both
rivets on the shelf
support are fully
inserted into the
keyhole slots, and
are firmly seated at
the bottom of the
keyhole as shown in
step 6.
“T”
UP-
RIGHT
6. PLEASE NOTE: To firmly seat shelf supports
and backstops, make sure both rivets are fully
inserted in the keyhole slots, and firmly seated
in the bottom of the slot. A rubber mallet can
be helpful in accomplishing this. Supports are
not fully seated unless you can see an
open space through the hole in the shelf
support as shown below.
NOT
SEATED
PROPERLY
SEATED
7. Hold a second “L” upright
(or a “T” upright if you are
assembling multiple units)
approximately 36" away.
Pull the first upright away
from the wall using the
shelf support you attached
in step 3, and insert the
other end of the shelf
support into the second
upright. NOTE: Take care
not to let the uprights
fall, as they are not
stable until step 8 is
completed.
8. Place a shelf support at the rear of the unit in the
bottom keyhole slots, in the same way you placed
the shelf support in steps 5 through 7. Then,
place a second shelf support at bottom front of
unit.
9. Place a shelf (Ref. No. 3) on the unit by inserting
it so that it
nests into
the shelf
supports. A
properly
placed shelf
will fit flush
with the shelf supports as shown
below:
10. Continue the
assembly by placing
supports and shelves
as described in steps
8 through 9. The
recommended
spacing
between shelves
is fifteen inches,
(eight open keyhole
slots between
supports).
12.
If you are assembling only a single unit,
assembly is now complete (shown below left).
If you are assembling multiple units joined
together, your starter unit should have been
assembled with a “T” upright (shown below
right), as described in step two. Continue with
step 13.
Completed
Single Unit
Completed Unit
Ready for Add-On
13. Repeat steps 7 through 11, adding a new "L"
or "T" upright and connecting with shelf
supports to complete the add-on unit.
11. The top shelf supports and top shelf (Ref. No. 2)
should be installed flush with the upright top.
PACKING LIST
36W x 15D x 76H
5 openings
STARTER
RGL-1536S
ADD-ON
RGL-1536A
36W x 18D x 76H
5 openings
STARTER
RGL-1836S
ADD-ON
RGL-1836A
ITEM
NO.
DESCRIPTION
PART NO.
36W x 12D x 76H
5 openings
QUANTITY QUANTITY QUANTITY
STARTER
RGL-1236S
ADD-ON
RGL-1236A
1 a Open “L” Upright 1276LO 2 - - - - 1 a Open “L” Upright 1576LO - - 2 - - 1 a Open “L” Upright 1876LO - - - - 2 1b Closed “T” Upright 1276TO - 1 - - - 1b Closed “T” Upright 1576TO - - - 1 - 1b Closed “T” Upright 1876TO - - - - - 1
2 Shelf Support HS-3614 12 12 12 12 12 12
3 Shelf PBLS-3612 6 6 - - - 3 Shelf PBLS-3615 - - 6 6 - 3 Shelf PBLS-3618 - - - - 6 6
4 Plastic "L" Foot LTNF-L 4 - 4 - 4 5 Plastic "T" Foot LTNF-T - 2 - 2 - 2
6 Sliding Divider Kit RSDK-12 - - - - - -
Plain Shelf
(Item No. 3)
Open “L”
Upright
Shelf Support
(Item No. 2)
(Item No. 1a)
Open “T”
Upright
Plastic Foot for
"L" Upright
(Item No. 4)
Plastic Foot for
"T" Upright
(Item No. 5)
(Item No.
1b)
Tennsco makes every effort to ensure that all units ship complete and arrive undamaged. However, should your
unit contain missing or damaged parts, replacements may be obtained directly from Tennsco. To obtain
replacement parts, follow the instructions below or complete the form at www.tennsco.com/replacement.cfm
TO OBTAIN PROPER REPLACEMENT PARTS, PLEASE PROVIDE THE FOLLOWING INFORMATION:
!!
!
!!
!
!!
Model Number Purchase Date
!!
!
!!
Description of part(s) needed and part Your company name
number(s) as shown in Parts List (above) Contact person's name
!!
!
!!
Color (Sand) Who the product was purchased from
!!
!
!!
Was item missing, or was it damaged?
!!
!!
!
!!
!!
!
!!
!!
!
!!
Tennsco Corp., P.O. Box 1888, Dickson, TN 37056-1888 Voice: (866) 446-8686 Fax: (866) 864-4796
If requesting parts by telephone, ask for customer service and have as much of the above information ready as possible.
Loading...