Tennsco 1480 User Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1740708

TENNSCO STORAGE CABINET

Model 1480

Tennsco Corp., Dickson, TN 37056-1888  [phone]

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!

Congratulations on your purchase of a
Tennsco Storage Cabinet! Tennsco's 1480 units
are general purpose storage cabinets that
provide a level of quality you won't find
elsewhere. They provide secure storage for
office supplies, books, records, small parts,
tools, etc.

These cabinets offer five openings with four
adjustable shelves, a locking chrome handle
with two keys, and a three-point locking system
for extra security.

Tennsco's cabinets are constructed from top
quality 22 to 24 gauge steel, with 22 gauge
steel shelves, offering weight capacities of up to
200 lbs. per shelf (evenly distributed). Our
attractive and durable powder-coated paint
finish will provide for years of service.

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must
be taken when handling various pieces to avoid
injury. For safety, wear a pair of work gloves when
assembling or performing any maintenance on
your cabinet.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder.
This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification or repair by persons
not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced, modified or removed. UNLESS
CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT

SELLERS OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place
of business or require Buyer to return the goods to Seller for inspection on Sellers premises. Transportation charges covering returned goods will be borne by
Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.

TENNSCO Corp., P.O. BOX 1888, DICKSON, TN 37056-1888

[phone] or [phone] (toll free)

Website: www.tennsco.com E-mail: [e-mail]

PK-1740708

INSTALLATION OF 1480 CABINETS

Tools Needed: A free 11/32" nut driver is provided with each Tennsco cabinet (Ref. No. 17). In addition,

you will need a flathead screwdriver. A hammer is required to install the hinge pin and lock bar.

Two people recommended for installation. Approximate assembly time: 15 to 25 minutes.

1. The reference numbers used throughout this

sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as
they are mentioned.

2. Place the cabinet back (Ref. No. 1) on a

protected surface to prevent
scratching the paint. The
flange on the
bottom of
the back
should be facing
upward.

Flange faces upward

3. Attach the left side (Ref. No. 2) to the back by

placing flange (A) around the back and
bolting the back and
side together with
seven bolts
and nuts
(Ref.

Nos.
18 &19).
Be sure
that the lances
on all shelf
adjustment
strips (B) point
in the same

direction.

All lances point UP

B

on both back
and side.

A

Flange goes

under back

5. To help hold the sides in position, insert one

shelf (Ref. No. 4) into the approximate center of
the unit, inserting the shelf edges into the
lances on all

four shelf

adjustment strips.
Be sure that the
channeled edge of
the shelf

is toward
the cabinet
front. If
a lance
is too
tight, it
may be
helpful to use
a screwdriver to
SLIGHTLY pry it open.

6. Insert bolts into the outside

holes on the header (Ref.
No. 5), placing two on each end
as shown in Inset A. Attach
the nuts, but do not tighten. Next, insert
the loose bolt heads on the
header into the large
end of the
keyhole
slots
at the
top of
each
side panel.
Slide the bolt
heads securely into the

smaller end
of the keyhole slot, and tighten the
four nuts securely.

Inset A

Two bolts

and nuts on

each side

Inset B

4. Attach the right side (Ref. No. 3) to the back in

the same manner as you did in step 3,

again making sure that
the flange is around the
back and that the lances

on the

and left side.

shelf adjustment

strips are
pointed
in the
same

direction as

those on the back

7. Attach the sill (Ref. No. 6) to the two holes on

each side of the cabinet bottom, using the same
technique you used to attach
the header in step 6.

Inset A

Loosely place

two bolts and

nuts on each

side, then

slide into

keyhole slots

and secure.

Place bolt heads into
keyhole slots, slide to

narrow end, and

secure nuts.