Tennsco 1471 User Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1750608

TENNSCO WARDROBE CABINET

Model 1471

Tennsco Corp., Dickson, TN 37056-1888  [phone]

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!

Congratulations on your purchase of a
Tennsco Wardrobe Cabinet! Tennsco's 1471
units provide a level of quality you won't find
elsewhere. They provide secure storage with a
hanging rod for jackets, clothing, and other
hanging garments, along with one shelf for
hats, books, tools, and other general storage.

These cabinets also offer a locking chrome
handle with two keys, and a three-point locking
system for extra security.

Tennsco's cabinets are constructed from top
quality 22 to 24 gauge steel, with 22 gauge
steel shelves, offering weight capacities of up to
200 lbs. per shelf (evenly distributed). Our
attractive and durable powder-coated paint
finish will provide for years of service.

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must
be taken when handling various pieces to avoid
injury. For safety, wear a pair of work gloves when
assembling or performing any maintenance on
your cabinet.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder.
This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification or repair by persons
not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced, modified or removed. UNLESS
CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT

SELLERS OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place
of business or require Buyer to return the goods to Seller for inspection on Sellers premises. Transportation charges covering returned goods will be borne by
Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.

TENNSCO Corp., P.O. BOX 1888, DICKSON, TN 37056-1888

[phone] or [phone] (toll free)

Website: www.tennsco.com E-mail: [e-mail]

PK-1750608

ASSEMBLY OF 1471 CABINETS

Tools Needed: A free 11/32" nut driver is provided with each Tennsco cabinet (Ref. No. 19). In addition,

you will need a flathead screwdriver. A hammer is required to install the hinge pin and lock bar.

Two people recommended for assembly. Approximate assembly time: 15 to 25 minutes.

1. All reference numbers refer to the illustration on

the back cover. This is to help you to identify the
various parts as they are mentioned.

2. Prepare the header (Ref. No. 5) for

installation by inserting a bolt into
the two outside holes on
each end, as
shown in Inset A.
The center hole
should remain empty.

Sill

Inset A

Header

Loosely attach nuts to each bolt,
leaving enough slack so that
the bolt heads may later be insert­ed into a slot. Prepare the sill (Ref.
No. 6) in the same way.

3. Place the

cabinet

back (Ref. No. 1)
on a protected surface to
prevent
paint. The

scratching

flange

on the bottom of

the

Flange faces upward

the back should be
facing upward.

4. Attach the left side (Ref. No. 2) to the back by

placing flange (A) around the back and
bolting the pieces
together with
seven bolts
and

Flange goes

A

under back

nuts
(Ref.
Nos.
18 &19).
Be sure that

All lances point UP

B

on both back
and side.

the lances on
all shelf adjustment
strips (B) point in the same direction.

5. Attach the right side (Ref. No. 3) to the back in

the same manner as you
did in step 4.
Make sure
that the
lances
on the
right side
are pointed in
the same direction
as those on the back and
the left side.

6. Locate the

two keyhole

-shaped
slots on the front of
each

end-panel

bottom.

Attach
the sill (Ref.
No. 6) by
inserting the
loose bolt heads
(which you attached

Inset B

to the sill in step 2) into the large end
of the keyhole slots (Inset B). Position
by sliding the bolts securely into the
smaller
shows improper
boltheads.

7. Insert

position
Do this by inserting

end of

the slots. Inset C at right

and proper

Tighten the four nuts

the shelf

(Ref. No. 4) into the top

on the

shelf adjustment strips.

the shelf edges

seating of

securely.

Inset C

Improperly

seated

into the lances on all four strips.
Be sure

that the channeled edge
of the shelf is toward the
cabinet front. If a
lance is too
tight, it
may be
helpful to
use a
screwdriver
to SLIGHTLY
pry it open.

8. Locate the two keyhole-shaped slots on the top

front of each end-panel. Attach the header (Ref.
No. 5) in the same way you attached
the sill, by inserting the previously
attached loose bolt heads
into the large end
of the key­hole
slots
(Inset D)

.
Position
by sliding
the bolts
securely into the
smaller

end of the

slots. Refer to Inset C
(in step 6 above) for improper and
proper

seating

of the boltheads. Tighten

the four nuts securely.

Two bolts

and nuts on

each side

Inset D

Properly

seated