Tennsco 1442 Assembly Instructions Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1470712

TENNSCO STORAGE CABINET

Model 1442

Tennsco Corp., Dickson, TN 37056-1888 • [phone]

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE!

Congratulations on your purchase of a
Tennsco Storage Cabinet! Tennsco's 1442 units
are general purpose desk high storage cabinets
that provide a level of quality you won’t find
elsewhere. They provide secure storage for office
supplies, books, records, small parts, tools, etc.
The 1442 offers three openings with two
adjustable sheves, a locking chrome handle with

GENERAL SAFETY INFORMATION:

pieces to avoid injury. For safety, wear a pair of work gloves when assembling or performing any maintenance on your cabinet.

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder.
This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification or repair by
persons not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced, modified or removed.
UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS

AT SELLER’S OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR

OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place
of business or require Buyer to return the goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne
by Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.

Some parts may have sharp edges. CARE must be taken when handling various

LIMITED WARRANTY

two keys, and a three-point locking system
for extra security.
Tennsco’s cabinets are constructed from
top quality 20 to 24 gauge steel, with 20 gauge
steel shelves offering weight capacities of 150
lbs. per shelf (evenly distributed). Our attractive
and durable powder-coated paint finish will
provide for years of service.

TENNSCO Corp., P.O. BOX 1888, DICKSON, TN 37056-1888

[phone] or [phone] (toll free)

Website: www.tennsco.com E-mail: [e-mail]

PK-1470712

INSTALLATION OF 1442 CABINET

Tools Needed: A free 11/32" nut driver is provided with each Tennsco cabinet (Ref. No. 16).

In addition, you will need a flathead screwdriver. A hammer is required to install the hinge pin.

Two people recommended for assembly. Approximate assembly time: 15 to 25 minutes.

1. The reference numbers used throughout this

sheet refer to the illustration on the back cover.
This is to help you to identify the various parts
as they are mentioned.

2. Place the cabinet back (Ref. No. 1) on a

protected surface to prevent
scratching the paint. The
flange on the
bottom of
the back
should be facing
upward.

Flange faces upward

NOTE: When bolting the unit together, leave the bolts
slightly loose until Step 8, unless otherwise specified.

3. Attach the left side (Ref. No. 2) to the back by

placing flange (A) around the back and bolting
the back and
with

four bolts
and nuts
(Ref.
Nos. 17

& 18).
Be sure
that

the
lances on
shelf adjustment
strips (B) point in the same direction.

side together

all

All lances point

B

UP on both back
and side.

A

Flange goes

under back

5. Attach the right side (Ref. No. 3) to the back in

the same manner as you did in step 3, again
making sure that the flange is around the back
and that the lances on the shelf adjustment strips
are pointed in the
back and left side. Push the side panel up so the
studs in the top go through the holes in the top
flange of side and fasten with
three nuts.

6. Attach the sill (Ref. No. 5) to the

loosely on each of the studs and slide the ends of
the sill into the slots on both sides of the unit.
Then,
securely
tighten
the
nuts.

same direction as those on

sides.

Nuts placed loosely
on studs of the sill.

the

Place nut

4. Attach the top (Ref. No. 7) to the unit by sliding

the outer flange over the back of the unit and the
side flange to the side panel
on the unit. The threaded
studs should go
through the
holes in
the top
flange of
the side
and fasten
with three nuts.
Attach the back to
the top using four
bolts and nuts.

Slide ends in to the slots on
the bottom of the sides.

7. Place rear flange of the bottom (Ref. No. 6) into

the bottom lances of the back. The flange with
two holes should face
the front, hanging
over the sill. Insert
bolts through the
bottom and sill with
the head facing
the front of the unit.
Secure with two nuts.

Two holes must

be in front

Insert shelf into

bottom lances.