TENDA TECHNOLOGY W307R Users Manual

11N Wireless Broadband Router

is the registered trademark of Shenzhen

Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda T echnology Co. , Ltd. Without the permission of Shenzhen Tenda Technology Co., Ltd, any individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages.

All the photos and product specifications mentioned in this manual are for references only. As the upgrade of software and hardware, there will be changes. And if there are changes, T enda is not responsible for informing in advance. If you want to know more about our product information, please visit our website at www.tenda.cn

11N Wireless Broadband Router

CONTENTS

Chapter 1: Introduction ........................................1

1.1 Product Features..................................................2

1.2 Package Contents ................................................4

1.3 LED Indicator and Port Description....................4

Chapter 2 Hardware Installation..........................7

2.1 How to Install the Router......................................7

2.2 Network Application Plan.....................................9

Chapter 3 How to Login to the Router .............. 10

3.1 How to Set the Network Configurations...........10

3.2 Login to the Router.............................................13

Chapter 4: Quick Setup Guide...........................15

4.1 Setup Wizard.......................................................15

Chapter 5: Advanced Settings........................... 21

5.1 LAN Settings .......................................................21

5.2 WAN Settings......................................................22

5.3 MAC Address Clone...........................................25

5.4 DNS Settings.......................................................26

5.5 WAN Media Type.................................................27

Chapter 6: Wireless Setting ............................... 29

6.1 Basic Settings.....................................................29

6.2 Wireless Security Setting...................................32

6.3 Advanced Settings..............................................40

11N Wireless Broadband Router

6.4 WPS Settings.......................................................42

6.5 WDS Settings ......................................................44

6.6 Wireless Access Control....................................46

6.7 Connection Status..............................................47

Chapter 7: DHCP Server..................................... 48

7.1 DHCP Settings.....................................................48

7.2 DHCP List and Binding.......................................49

Chapter 8 Virtual Server.....................................50

8.1 Single Port Forwarding ......................................50

8.2 Port Range Forwarding......................................52

8.3 ALG Service Settings .........................................54

8.4 DMZ Settings.......................................................55

8.5 UPNP Settings.....................................................56

Chapter 9 Traffic Control.................................... 57

9.1 Traffic Control.....................................................57

9.2 Traffic Statistics..................................................59

Chapter10 URL Monitor...................................... 60

10.1 URL Monitor ......................................................60

Chapter 11: Security Settings............................63

11.1 Client Filter Settings.........................................63

11.2 URL Filter Settings............................................64

11.3 MAC Address Filter...........................................66

11.4 Prevent Net work Attack....................................67

11.5 Remote Web Management ...............................68

11.6 Local Web Management...................................69

11N Wireless Broadband Router

11.7 WAN Ping...........................................................70

Chapter12 Routing Setting................................. 71

12.1 Routing T able....................................................71

12.2 Static Routing....................................................71

Chapter 13 System Tools ................................... 73

13.1 Time Settings ....................................................73

13.2 DDNS..................................................................74

13.3 Backup/Restore Settings.................................76

13.4 Restore to Factory Default Setting..................78

13.5 Upgrade Firmware ............................................79

13.6 Reboot the Router.............................................79

13.7 Password Change.............................................80

13.8 System Log........................................................81

13.9 Logout................................................................81

Appendix 1：Glossary........................................ 82

Appendix 2: Ask and Question.......................... 85

11N Wireless Broadband Router

Chapter 1: Introduction

Thank you for purchasing Tenda W307R 11N Wireless Broadband Router!

W307R utilizes advanced MIMO technology and increases over 8 times transmission range of ordinary

802.11g products. Compatible with IEEE802.11n (Draft

4.0) and IEEE802.11g/b standards, it can provide up to 300Mbps stable transmission rate. Additionally, it includes router, wireless access point, four-port switch and firewall in one, dedicated to SOHOs (Small Office/Home Office) and family networking.

It supports WDS (Wireless Distribution System) function for repeating and amplifying the signals to extend the wireless network coverage. Besides, the Router also supports all of the latest wireless security features, such as 64/128-bit WEP, WPA, WPA2, WPA&WPA and W PS (PBC and PIN) encryption methods, packet filtering and port forwarding, to prevent unauthorized access and protect your network against malicious attack.

In addition, URL and MAC address filtering can take it easy for parents and network administrator to manage network life and QoS bandwidth control over specific

11N Wireless Broadband Router

computer’s downloading speed is supported as well. Moreover, UPnP and WMM support can smooth your MSN voice better, and the included Setup Wizard on CD-ROM will be easy and fast for non-savvy users to install the device and access to the Internet.

1.1 Product Features

z Includes router, wireless access point,

four-port switch and firewall in one

z Provides up to 300Mbps uploading and

downloading speed

z Supports two WPS (Wi-Fi Protected Setup)

encryption methods: PBC and PIN

z Compliant to IEEE802.11n, IEEE802.11g,

IEEE802.11b, IEEE802.3 and IEEE802.3u standards

z Supports over 8 times transmission range of

11G products

z Supports 64/128-bit WEP, WPA, WPA2,

WPA&WPA2 encryption methods

z Supports RTS/CTS protocol and data

partitioning function

z Provides one 10/100Mbps Auto-Negotiation

Ethernet WAN port

z Provides four 10/100Mbps Auto-Negotiation

11N Wireless Broadband Router

Ethernet LAN ports

z Supports xDSL/Cable MODEM, static and

dynamic IP in community networking

z Supports remote/local Web management z Supports WMM to better smooth your voice and

video

z Supports SSID stealth mode and access control

based over MAC address (up to 30 entries)

z Supports Auto MDI/MDIX z Supports wireless Roaming technology for

high-efficient wireless connections

z Supports auto negotiation/manual mode for

802.11b/802.11g/802.11n

z Supports UPnP and DDNS z Supports Firefox 1.0, IE5.5 or above z Supports SNTP z Supports virtual server, DMZ host z Built-in firewall for hacker's attack prevention z Supports DHCP server/client z Supports auto wireless channel selection z Supports LAN access control to the Internet z Provides syslog to record the status of the

router

z Supports WDS wireless network extension z Supports QoS function

11N Wireless Broadband Router

1.2 Package Contents

Please unpack the box and check the following items:

¾ One W307R 11N Wireless Broadband Router ¾ One Quick Installation Guide ¾ One Power Adapter ¾ One CD-ROM

If any of listed items are missing or damaged, please contact the Tenda reseller from whom you purchased for replacement immediately.

1.3 LED Indicator and Port Description

Front Panel and LED Indicator Show

LED indicator description on front panel: (from L to R)

11N Wireless Broadband Router

¾ POWER

When turns green, Always ON indicates the power connects well.

¾ SYS

When turns green, blinking indicates the system runs well.

¾ WPS

When blinking, it in dicates the device is negotiating with client in WPS mode.

¾ WLAN

Wireless signal LED indicator. When turns green, blinking indicates the wireless function is enabled.

¾ LAN (4,3,2,1)

Wired local network LED indicator. Always ON indicates it is connected with Ethernet device; blinking indica tes t he de vice is t r ansm ittin g and /or receiving data.

¾ WAN

Wide area network indicator. Always ON indicates the Router’s WAN Port.

Back Panel Show：

11N Wireless Broadband Router

Rear Panel：（From L to R）

¾ POWER

The jack is for power adapter connection. Please

use the included 9V DC power adapter.

¾ WAN

A 100Mbps Ethernet port, can be connected with MODEM, Switch, Router and other Ethernet device for Internet connecting to DSL MODEM, Cable MODEM and ISP.

¾ LAN (1, 2, 3, 4)

4 10/100Mbps Ethernet ports can be connected with Ethernet switch, Ethernet router and NIC card.

¾ RESET/WPS

The combination button for system reset and WPS features. Press this button for 7 seconds, the settings configured in this device will be deleted and it will restore the settings to the default one. Press it for one second, the WPS feature will be enabled.

11N Wireless Broadband Router

Chapter 2 Hardware Installation

2.1 How to Install the Router

After you unpack the box, please follow the steps below to connect. For better wireless performance, please put the device in the middle of wireless coverage area.

Please use the included power adapter to power on the Router. IMPORTANT: Use of a different power adapter could cause damage and void the warranty for this product.

Please connect the LAN port of the Router to the network adapter of your computer with a cable.

11N Wireless Broadband Router

Please connect your broadband line provided by your ISP to the WAN port.

Insert the included CD-ROM into the CD-ROM drive, double click the “Setup ” icon and fol low the instruc tions to complete the installation. Or you can enter the Router’s Web page to configure it. (More details please refer to Chapter 3.)

11N Wireless Broadband Router

2.2 Network Application Plan

Usually wireless LAN Network is deployed in a planned environment where each access point is located in a steady place with certain wireless coverage area for communication service. Generally speaking, it is in the center of the area to reduce “dead spot”.

11N Wireless Broadband Router

Chapter 3 How to Login to the Router

The chapter mainly presents how to enter the Router’s Web page. After you have finished the hardware installation, the following steps will assist you to set the network configurations for you computer.

3.1 How to Set the Network Configurations

1. On your computer desktop right click “My Network Places” and select “Properties”.

11N Wireless Broadband Router

2. Right click “Local Area Network Connection” and select “Properties”.

3 ． Select “Internet Protocol (TCP/IP)” and click

“Properties”.

11N Wireless Broadband Router

4． Select “Obtain an IP address automatically” and

“Obtain DNS server address automatically”. Click “OK” to save the configurations.

Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as follows: IP Address: 192.168.0.XXX：(XXX is a number from

2~254) Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 Certainly you need to input the DNS server address provided by your ISP. Otherwise, you can use the Router’s default gateway as the DNS proxy server. Click “OK” to save the configurations.

11N Wireless Broadband Router

3.2 Login to the Router

1．To access the Router’s Web-based interface, launch

a web browser such as Internet Explorer or Firefox and enter the Router’s default IP address, http://192.168.0.1. Press “Enter”.

11N Wireless Broadband Router

2．Input the “admin” in both User Name and Password.

Click “OK”.

3. If you enter the correct user name and password, the

screen will be the next one.

11N Wireless Broadband Router

Chapter 4: Quick Setup Guide

This chapter deals with how to access the Internet quickly. Please follow this guide to connect your Router to the Internet.

4.1 Setup Wizard

Here is the “Welcome to Setup Wizard” for configuring your Router quickly. Click “Next”.

In this screen, select one mode of your Internet connection you use. If you are not clear, press the “Detect” button or contact your Internet Service Provider, and click “Next”.

11N Wireless Broadband Router

ADSL Virtual Dial-up (Via PPPoE)

Enter the Account and Password provided by your ISP, and click “Next”. For example：

Dynamic IP (Via DHCP)

If your connection mode is Dynamic IP, it means your IP address keeps changing every time you connect. Y ou do not need to enter the information like other modes. Click “Next” and “Save” to finish the settings.

11N Wireless Broadband Router

Static IP

In this screen, fill th e network addres s information from your ISP in the IP Address, Subnet Mask, Gateway and Primary DNS server fields and click “Next”.

For example：

ISP provides the following TCP/IP parameters as follows： IP Address：192.168.1.2 Subnet Mask：255.255.255.0 Gateway：192.168.1.1 Primary DNS Server：192.168.1.2 Alternate DNS Server：202.96.134.133

11N Wireless Broadband Router

Click “Save” to complete the setup wizard. The Router will record the settings you made. To activate the settings, it is recommended to select “Reboot the Router” from “System Tool” of the left menu. It is rebooting now, please wait for a few minutes and DO NOT power off it.

Click the “System Status” in the left menu of the Web-based Utility to find out the current network and system information. If the “Connection Status” is “Connected”, Congratulations you on completing the Router’s basic settings. You are on the Internet now. If you want to configure more, please proceed to the following explanations for Advanced Settings.

11N Wireless Broadband Router

L2TP

L2TP Server IP: Enter the Server IP provided by your

ISP.

User Name: Enter L2TP username. Password: Enter L2TP password. MTU: Maximum Transmission Unit, you may need to

change it for optimal perfo rmance with your sp ecific ISP. 1400 is the default MTU. Address Mode: Select “Static” if your ISP supplies you with the IP address, subnet mask, and gateway . In most cases, select Dynamic. IP Address: Enter the L2TP IP address supplied by your ISP. Subnet Mask: Enter the Subnet Mask supplied by your ISP.

Default Gateway:

by your ISP.

Enter the Default Gateway supplied

11N Wireless Broadband Router

PPTP

PPTP Server IP: Enter the Server IP provided by your

ISP. User Name: Enter PPTP username provided by your ISP.

Password: Enter PPTP password provided by your ISP . Address Mode: Select “Static” if your ISP supplies you

with the IP address, subnet mask, and gateway . In most cases, select Dynamic.

IP Address:

your ISP. Subnet Mask: Enter the Subnet Mask supplied by your ISP.

Default Gateway:

by your ISP.

Enter the PPTP IP address supplied by

Enter the Default Gateway supplied

11N Wireless Broadband Router

Chapter 5: Advanced Settings

5.1 LAN Settings

LAN Settings are for the basic TCP/IP parameters of LAN ports.

¾ MAC Address: The Router’s physical MAC address

as seen on your local network, which is unchangeable.

¾ IP Address: The Router’s LAN IP addresses (not

your PC’s IP address). 192.168.0.1 is the default value.

¾ Subnet Mask: It’s shown the Router’s subnet

mask for measurement of the network size.

255.255.255.0 is the default value.

IMPORTANT:

Once you modify the IP address, you need to remember it for the Web-based Utility login next time.

11N Wireless Broadband Router

5.2 WAN Settings

After you have selected the ISP connection type in “Setup Wizard” and you want to modify the related settings, here you can modify and configure the settings in details.

Virtual Dial-up（PPPoE）

¾ Connection Mode: Show your current connection

mode.

¾ Account: Enter them provided by your ISP. ¾ Password: Enter them provided by your ISP. ¾ MTU: Maximum Transmission Unit. It is the size of

largest datagram that can be sent over a network.

11N Wireless Broadband Router

The default value is 1492. Do NOT modify it unless necessary. But if when some specific website or web application software can not be open or enabled, have a try to change the MTU value as 1450, 1400, etc.

¾ Service Name: It is defined as a set of

characteristics that are applied to a PPPoE connection. Enter it if provided. Do NOT modify it unless necessary.

¾ AC Name: Enter it if provided. Do NOT modify it

unless necessary.

¾ Connect Automatically: Connect automatically

to the Internet after rebooting the system or connection failure.

¾ Connect Manually: Connect to the Internet by

users manually.

¾ Connect on Demand: Re-establish your

connection to the Internet after the specific time (Max Idle Time). Zero means your Internet connection at all time. Otherwise, enter the minutes to be elapsed before you want to disconnect the Internet access.

¾ Connect on Fixed Time: Connect to the Internet

during the time you fix.

Notice:

The “Connect on Fixed Time” can be deployed only when you have set the current time in “Time Settings” from “System Tools”.

11N Wireless Broadband Router

Static IP

If your connection mode, static IP is chosen, you can modify the following addressing information.

¾ IP Address: Here enter the WAN IP address

provided by your ISP.

¾ Subnet Mask: Enter the WAN Subnet Mask

here.

¾ Gateway: Enter the WAN Gateway here. ¾ Primary DNS Server: Enter the Primary DNS

server provided by your ISP.

¾ Secondary DNS Server: Enter the secondary

DNS.

11N Wireless Broadband Router

5.3 MAC Address Clone

This page is for the Router’s MAC address to WAN.

Some ISPs require end-user's MAC address to access their network. This feature copies the MAC address of your network device to the Router.

¾ MAC Address: The MAC address to be registered

with your Internet service provider.

¾ Clone MAC Address: Register your PC's MAC

address.

¾ Restore Default MAC Address: Restore to the

default hardware MAC address.

11N Wireless Broadband Router

5.4 DNS Settings

DNS is short for Domain Name System (or Service), an Internet service that translate domain names into IP addresses which are provided by your Internet Service Provider. Please consult your Internet Service Provider for details if you do not have them.

¾ DNS: Click the checkbox to enable the DNS server.

The Router’s DHCP sever will answer the client’s requests and distribute DNS address.

¾ Primary DNS Address: Enter the necessary

address provided by your ISP.

¾ Secondary DNS Address: Enter the second

address if your ISP provides, which is optional.

Notice:

After the settings are completed, reboot the device to activate the modified settings.

11N Wireless Broadband Router

5.5 WAN Media Type

In most cases, ISP provides wired WAN access (ADSL MODEM, Cable MODEM, etc.) and you only need to insert the line into the Router’s WAN port. Sometime, wireless WAN access type, more flexible and convenient, is also provided by some ISP.

¾ Wired WAN: In this type, WAN port should be

connected by wired cable. This type is the device’s default option.

¾ Wireless WAN: When your ISP provides wireless

access service, you can enable this WAN access type.

¾ SSID: SSID (Service Set Identifier) is the ID name

of the wireless device. You must input the correct SSID and keep it the same SSID with your ISP’s wireless device. Oth erwise, it is not allowed to have

11N Wireless Broadband Router

access to your ISP network. Click “Open Scanner’ to search the available SSID.

¾ MAC: Enter the MAC address of ISP wireless device.

Click “Open Scanner’ to search the MAC address.

¾ Channel: Wireless device’s communication

channel. Keep it the same channel with your ISP’s wireless device. Click “Open Scanner’ to search the available AP chan n e l.

¾ Security Mode: If your ISP has set the security

parameters, the receiving station must set the same security mode, encryption method and key with ISP’s device.

If you know the ISP wireless device’s SSID, enter the SSID, Wireless MAC address, Channel and Encryption method into the corresponding fields. Certainly you can click the “Open Scanner” button to fill these fields automatically. After you apply the settings, In “Setup Wizard” page select the corresponding WAN connection type to connect the Internet. For example: If your ISP wireless device provides Dynamic IP access type, you need to select “Dynamic IP (Via DHCP)”.

11N Wireless Broadband Router

Chapter 6: Wireless Setting

6.1 Basic Settings

¾ Enable Wireless: Check to enable the Router’s

wireless features; uncheck to disable it.

¾ Network Mode ： Select one mode from the

following. The default is 11b/g/n mode.

11N Wireless Broadband Router

11b mode： Allow the wireless client to connect

with the device in 11b mode at the maximum speed of 11Mbps.

11g mode： Allow the 11g/11n-compliant client

device to connect with the AP at the maximum speed of 54Mbps.

11b/g mode: Allow the 11b/g-compliant client

device to connect with the AP with auto-negotiation speed, and 11n wireless client to connect the device with 11g speed.

11b/g/n mode：Allow 11b/g/n-compliant client

device to connect with the AP with auto-negotiation speed.

¾ Main SSID：SSID (Service Set Identifier) is the

unique name of the wireless network. This device has two SSID and the main SSID is necessary.

¾ Minor SSID：It is optional. ¾ Broadcast (SSID): Select “Enable” to enable the

device's SSID to be visible by wireless clients. The default is enabled.

¾ MBSSID AP Isolation ： One access control

feature based on wireless MAC address. When this feature is enabled, wireless clients connected with the same SSID can not communicate with each other. For example, configure main SSID as AP1, minor SSID as AP2. PC1 and PC2 connect to AP1

11N Wireless Broadband Router

via wireless adapter, and configure PC1 and PC2 in the same segment. After the feature is enabled, two PCs can not communicate and share network resource each other, but they can communicate with wireless clients connected with AP2. This feature is to isolate the communication of wireless clients connected with the same SSID.

¾ AP Isolation: One access control feature based on

SSID. When this feature is enabled, each of your wireless clients will be in its own virtual network and will not be able to communicate with each other. When this feature is enabled , wireless clients connected with the Main SSID and Minor SSID can not communicate with each other , which can secure the wireless network strongly. For example, configure main SSID as AP1, minor SSID as AP2. PC1 connects to AP1 via wireless adapter; PC2 connecting to AP2. After the feature is enabled, two PCs can not communicate and share network resource each other. This feature is to isolate the communication of wireless clients connected with different SSID.

¾ Tip: If you want to isolate all connected wireless

client's communication, please enable MBSSID AP Isolation and AP Isolation simultaneously.

¾ BSSID： Basic Service Set Identifier of wireless

network. In IEEE802.11, BSSID is the MAC address of wireless access point.

11N Wireless Broadband Router

¾ Channel： Speci fy the effective channel (from 1

to 13\Auto) of the wireless network.

¾ Extension Channel：T o increase data throughput

of wireless network, the extension channel range is used in 11n mode.

¾ Channel Bandwidth ： Select the channel

bandwidth to improve the wireless performance. When the network has 11b/g and 11n clients, you can select the 40M; when it is an 11n network, select 20/40M to improve its throughput.

6.2 Wireless Security Setting

It is used to configure the AP network’s security setting. Here presents the common six (ten in all) encryption methods, including Mixed WEP, WPA-personal, WPA-enterprise, WPA2-personal, WPA2- enterprise, etc.

6.2.1 Mixed WEP WEP (Wired Equivalent Privacy), a basic encryption method, usually encrypts wireless data using a series of digital keys (64 bits or 128 bits in length). By using the same keys on each of your wireless network devices, you can prevent unauthorized wireless devices from monitoring your transmissions or using your wireless

11N Wireless Broadband Router

resources. Select Mixed WEP to enter the following window:

¾ Select SSID： Select the SSID (main SSID or

minor SSID) to configure security setting from the drop-down menu.

¾ Security Mode：From the drop-down menu select

the corresponding security encryption modes.

¾ WEP Key1~4：Set the WEP key with the format of

ASCII and Hex. You can enter ASCII code (5 or 13 ASCII characters. Illegal character as “/” is not allowed.) Or 10/26 hex characters.

¾ Default Key ： Select one key from the four

configured keys as the current available one.

11N Wireless Broadband Router

6.2.2 WPA-Personal WPA (Wi-Fi Protected Access), a Wi-Fi standard, is a more recent wireless encryption scheme, designed to improve the security features of WEP. It applies more powerful encryption types (such as TKIP [Temporal K ey Integrity Protocol] or AES [Advanced Encryption Standard]) and can change the keys dynamically on every authorized wireless device.

¾ Select SSID： Select the SSID (main SSID or

minor SSID) to configure security setting from the drop-down menu.

¾ WPA Algorithms：Provides TKIP [Temporal Key

Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode.

¾ Pass Phrase：Enter the encrypted characters with

8-63 ASCII characters.

¾ Key Renewal Interval： Set the key’s renewal

period.

11N Wireless Broadband Router

6.2.3 WPA2- Personal WPA2 (Wi-Fi Protected Access version 2) provides higher security than WEP (Wireless Equivalent Privacy) and WPA (Wi-Fi Protected Access).

¾ Select SSID： Select the SSID (main SSID or

minor SSID) to configure security setting from the drop-down menu.

¾ WPA Algorithms：Provides TKIP [Temporal Key

Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode.

¾ Pass Phrase：Enter the encrypted characters with

8-63 ASCII characters.

¾ Key renewal Interval： Set the key’s renewal

period.

11N Wireless Broadband Router

6.2.4 WPA- Enterprise This security mode is used when a RADIUS server is connected to the device. Select “WPA-Enterprise” from the drop-down menu to enter the following window:

¾ Select SSID： Select the SSID (main SSID or

minor SSID) to configure security setting from the drop-down menu.

¾ WPA Algorithms：Provides TKIP [Temporal Key

Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode.

¾ Key Renewal Interval： Set the key’s renewal

period.

¾ Radius Server：Enter the IP address of the Radius

server.

¾ Radius Server port： Enter the authentication

11N Wireless Broadband Router

port of the Radius server. The default is 1812.

¾ Shared Secret ： Enter the shared key for

authentication server with 8~63 ASCII characters.

¾ Session Timeout ： The authentication interval

period between AP and authentication server.

6.2.5 WPA2-Enterprise

This security mode is based on Radius authentication server and WPA2 encryption method. WPA2 is used when a RADIUS server is connected to the device. Select “WPA2-Enterprise” from the drop-down menu to enter the following window:

11N Wireless Broadband Router

¾ Select SSID： Select the SSID (main SSID or

minor SSID) to configure security setting from the drop-down menu.

¾ WPA Algorithms：Provides TKIP [Temporal Key

Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode.

¾ Key Renewal Interval： Set the key’s renewal

period.

¾ Radius Server：Enter the IP address of the Radius

server.

¾ Radius Server port： Enter the authentication

port of the Radius server. The default is 1812.

¾ Shared Secret ： Enter the shared key for

authentication server with 8~63 ASCII characters.

¾ Session Timeout： The authentication interval

period between AP and authentication server. The default is 3600s.

6.2.6 802.1X This security mode is used when a RADIUS server is connected to the device. 802.1x, a kind of Port-based authentication protocol, is an authentication type and strategy for users. The port can be either a physic port or logic port (such as VLAN). For wireless LAN users, a port is just a channel. The final purpose of 802.11x authentication is to check if the port can be used. If the port is authenticated successfully, you can open this

11N Wireless Broadband Router

port which allows all the messages to pass. If the port isn’t authenticated successfully, you can keep this port “disable” which just allows 802.1x authentication protocol message to pass. Select “802.1x” from the drop-down menu to enter the following window:

¾ Select SSID： Select the SSID (main SSID or

minor SSID) to configure security setting from the drop-down menu.

¾ WEP：Click “Enable/Disable” to enable or disable

the WEP algorithm.

¾ Radius Server：Enter the IP address of the Radius

server.

¾ Radius Server Port： Enter the authentication

port of the Radius server. The default is 1812.

¾ Shared Secret ： Enter the shared key for

authentication server with 8~63 ASCII characters.

11N Wireless Broadband Router

¾ Session Timeout ： The authentication interval

period between AP and authentication server. The default is 3600s.

Note:

To improve security level, do not use too easy characters. If you are not familiar with these ten security modes, it is recommended to use “WPA-Personal” mode.

6.3 Advanced Settings

This section is to configure the advanced wireless setting of the Router, in cl uding the Radio Preamble,

802.11g/n Rate, Fragmentation Threshold, RTS Threshold, etc.

11N Wireless Broadband Router

¾ BG protection Mode: Auto by default. It is for

11b/g wireless client to connect 11n wireless network smoothly in a complicated wireless area.

¾ Basic Data Rates: For different requirement, you

can select one of the suitable Basic Data Rates. Here, default value is (1-2-5.5.-11Mbps…). It is recommended not to modify this value.

¾ Beacon Interval: Set the beacon interval of

wireless radio. Default value is 100. It is recommended not to modify this value.

¾ Fragment Threshold: The fragmentation

threshold defines the maximum transmission packet size in bytes. The packet will be fragmented if the arrival is bigger than the threshold setting. The default size is 2346 bytes. It is recommended not to modify this value.

¾ RTS Threshold: RTS stands for “Request to Send”.

This parameter controls what size data packet the frequency protocol issues to RTS packet. The default value of the attribute is 2346. It is recommended not to modify this value in SOHO environment.

¾ TX Power: Set the output power of wireless radio.

The default value is 100.

¾ WMM Capable: It will enhance the data transfer

performance of multimedia data when they’re being transferred over wireless network. It is recommended to enable this option.

11N Wireless Broadband Router

¾ APSD Capable: It is used for auto power-saved

service. The default is disabled.

6.4 WPS Settings

WPS (Wi-Fi Protected Setting) can be easy and quick to establish the connection between the wireless network clients and the device through encrypted contents. The users only enter PIN code or press WPS button on the panel to configure it without selecting encryption method and secret keys by manual. In the “Wireless settings” menu, click “WPS settings” to enter the next screen.

¾ WPS settings：T o enable or disable WPS function.

The default is “disable”.

11N Wireless Broadband Router

¾ WPS mode：Provide two ways: PBC (Push-Button

Configuration) and PIN code.

¾ PBC：Select the PBC or press the WPS button on

the front panel of the device for about one second (Press the button for about one second and WPS indicator will be blinking for 2 minutes, which means the WPS is enabled. During the blinking time, you can enable another device to implement the WPS/PBC negotiation between them. Two minutes later, the WPS indicator will be off, which means the WPS connection is completed. If more clients are added, repeat the above steps. At present, the WPS supports up to 32 clients access.)

¾ PIN：If this option is enabled, you need to enter a

wireless client’s PIN code in the field and keep the same code in the WPS client.

¾ WPS Summary： Show the current state of Wi-Fi

protected setting, including authorized mode, encryption type, default key and other information.

¾ WPS Current Status：Idle means WPS in idle

state. Start MSC process means the process has been started and waits for being connected. Configured means the negotiation is successful between server and clients.

¾ WPS Configured： “yes” means WPS feature is

enabled and goes into effe ct. “not used” means it is not used. Usually the AP-security has been enabled, here will displayed “not used”.

¾ WPS SSID： Show the main SSID set by WPS.

11N Wireless Broadband Router

¾ WPS Auth. Mode ： The authorization mode

deployed by WPS, generally WPA/WPA2-personal mode.

¾ WPS Encrypt Type：The encryption type used by

WPS, generally AES/TKIP.

¾ WPS key： The effective key generated by AP

automatically.

¾ AP PIN（KEY）：The PIN code used by default. ¾ Reset OOB： When this button is pressed, the

WPS client will be idle state, and WPS indicator will be turned off. AP will not respond the WPS client’s requests and the set the security mode as WPA mode.

6.5 WDS Settings

WDS (Wireless Distribution System) is used to expand wireless coverage area. This Router provides three modes: Lazy, Bridge and Repeater.

11N Wireless Broadband Router

Lazy: In this mode, the connected device can be Bridge mode or Repeater mode and enter the Router’s BSSID to establish the connection. Bridge: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the Wireless MAC address of the connecting device into the Router's AP MAC address table or select one from the scanning table. Repeater Mode：In this mode, add the opposing MAC address into each own AP MAC address table by manual or scanner to enlarge and extend the wireless radio. Encrypt Type: Select one from WEP, TKIP, AES for security here. Pass phrase: Enter the encrypted key for wireless devices. AP MAC: Input the MAC address of another (opposing) wireless router you want to connect.

NOTE:

It is recommended that two wireless routers keep the same bandwidth, channel number , and security settings. Apply the settings and reboot the Router to activate it.

11N Wireless Broadband Router

6.6 Wireless Access Control

T o secure your wireless LAN, the wireless access control is actually based on the MAC address management to allow or block the specific clients to access the wireless network. Select “Wireless Setting->Access Control” to display the following screen:

¾ MAC Address Filter：Enable/disable MAC add ress

filter. Select “Close” to malfunction MAC address; “disable” to prevent the MAC addresses in the list from accessing the wireless network; “Allow” to allow the MAC address in the list to access the wireless network.

¾ MAC Address Management ： Input the MAC

address to implement the filter policy. Click “Add” to finish the MAC add operation.

¾ MAC list：Show the added MAC addresses. You

can add or delete them.

11N Wireless Broadband Router

6.7 Connection Status

This page shows wireless client’s connection status, including MAC address, Channel bandwidth, etc. Select “Wireless Setting->connection status” to enter the following screen:

¾ MAC Address：Shows current MAC addresses of

the hosts connecting to the Router.

¾ Bandwidth ： Shows current bandwidth of the

hosts (wireless client).

11N Wireless Broadband Router

Chapter 7: DHCP Server

7.1 DHCP Settings

DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When you enable the DHCP Server , the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating “Obtain an IP Address Automatically”. So specifying the starting and ending address of the IP Address pool is needed.

¾ DHCP Server: Activate the checkbox to

enable DHCP server.

¾ IP Address Start/End: Enter the range of IP

address for DHCP server distribution.

¾ Lease Time: The length of the IP address lease.

For example：

If the lease time is an hour, then DHCP server will reclaim the IP address in each hour.

11N Wireless Broadband Router

7.2 DHCP List and Binding

The Static IP ass ignment is to add a specifically static IP address to the assigned MAC address. You can view the related information in the DHCP server list.

¾ IP Address: Enter the IP address which needs to

be bound.

¾ MAC Address: Enter the MAC address of the

computer you want to assign the above IP address. Click “Add” to add the entry in the list.

¾ Hostname: The name of the computer which is

added a new IP address.

¾ Lease Time: The left time length of the

corresponding IP address lease.

11N Wireless Broadband Router

Chapter 8 Virtual Server

8.1 Single Port Forwarding

The Router can be configured as a virtual server on behalf of local services behind the LAN port. The given remote requests will be re-directed to the local servers via the virtual server. This section deals with the single port forwarding mainly. The Single Port Forwarding allows you to set up kinds of public services such as web servers, ftp, e-mail and other specialized Internet applications on your network.

¾ External Port: This is the external (WAN) port

number for server or Internet application, for

11N Wireless Broadband Router

example, port 21 for ftp service.

¾ Internal Port: This is the port number of LAN

computer set by the Router. The Internet traffic from the external port will forward to the internal port. For example：you can set the internal port NO.66 to act as the external port NO.21 for ftp service.

¾ IP Address: Enter the IP address of the PC where

you want to set the applications.

¾ Protocol: Select the protocol (TCP/UDP/Both) for

the application.

¾ Delete/Enable:Click to check it for corresponding

operation.

¾ Well-Known Service Port: Select the well-known

services as DNS, FTP from the drop-down menu to add to the configured one above.

NOTE:

If you set the virtual server of the service port as 80, you must set the Web management port on R emote Web Management page to be any value except 80 such as 8080. Otherwise, there will be a conflict to disable the virtual server.

11N Wireless Broadband Router

8.2 Port Range Forwarding

This section deals with the port range forwarding mainly . The Port Range Forwarding allows you to set up a r ange of public services such as web servers, ftp, e-mail and other specializ ed Interne t applications t o an assigned I P address on your LAN.

¾ Start/End Port: Enter the start/end port number

which ranges the External ports used to set the server or Internet applications.

¾ IP Address: Enter the IP address of the PC where

you want to set the applications.

11N Wireless Broadband Router

¾ Protocol: Select the prot ocol (TCP/UDP/Both) for

the application.

¾ Delete/Enable: Click to chec k it for corresponding

operation.

¾ Well-Known Service Port: Select the well-known

services as DNS, FTP from the drop-down menu to add to the configured one above.

¾ Add: Add the selected well-known port to the

policy ID.

NOTE:

11N Wireless Broadband Router

8.3 ALG Service Settings

In the context of computer networking, an ALG or application layer gateway consists of a security component that augments a firewall or NAT employed in a computer network. It allows customized NAT tra versal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, BitTorrent, SIP, RTSP, file transfer applications etc.

In order for these protocols to work through NAT or a firewall, either the application has to know about an address/port numbe r combin ation th at al lows inc omin g packets, or the NAT has to monitor the control traffic and open up port mappings (firewall pinhole) dynamically as required. Legitimate application data can thus be passed through the security checks of the firewall or NAT that would have otherwise restricted the

11N Wireless Broadband Router

traffic for not meeting its limited filter criteria.

Usually allowing client applications to use dynamic ephemeral TCP/ UDP ports to communicate with the known ports used by the server applications, even though a firewall-configuration may allow only a limited number of known ports. In the absence of an ALG, either the ports would get blocked or the network administrator would need to explicitly open up a large number of ports in the firewall; rendering the network vulnerable to attacks on those ports.

In the default ALG settings, the following protocols have enabled. It is recommended to keep the settings unchanged.

1. FTP

2. TFTP

3. PPTP

4. IPSec

5. L2TP

8.4 DMZ Settings

The DMZ function is to allow one computer in LAN to be exposed to the Internet for a special-purpose service as Internet gaming or videoconferencing.

11N Wireless Broadband Router

¾ DMZ Host IP Address: The IP address of the

computer you want to expose.

¾ Enable: Click the checkbox to enable the DMZ

host.

¾ IMPORTANT: When the DMZ host is enabled, the

firewall settings of the DMZ host will not function.

8.5 UPNP Settings

It supports latest Universal Plug and Play. This function goes into effect on Windows XP or Windows ME or this function would go into effect if you have installed software that supports UPnP. With the UPnP function, host in LAN can request the router to process some special port switching so as to enable host outside to visit the resources in the internal host.

¾ Enable UPnP: Click the checkbox to enable the

UPnP.

11N Wireless Broadband Router

Chapter 9 Traffic Control

9.1 Traffic Control

Traffic control is used to limit communication speed in the LAN and WAN. Up to 20 entries can be supported with the capability for at most 254 PCs' speed control, including for IP address range configuration.

¾ Enable Traffic Control: To enable or disable the

internal IP bandwidth control. The default is disabled.

¾ Interface: To limit the uploading and down loading

bandwidth in WAN port.

¾ Service: T o select the controlled service type, such

11N Wireless Broadband Router

as HTTP service.

¾ IP Starting Address: The first IP address for

traffic control.

¾ IP Ending Address: The last IP address for traffic

control.

¾ Uploading/Downloading: To specify the traffic

heading way for the selected IP addresses: uploading or downloading.

¾ Bandwidth: To specify the uploading/down loading

Min. /Max. Traffic speed (KB/s), which can not exceed the WAN speed.

¾ Apply: To enable the current editing rule. If not,

the rule will be disabled.

¾ Add: After edit the rule, click the “add to list”

button to add the current rule to rule list.

¾ Apply: Click “Save” to activate the current rule. ¾ Cancel: Click “Cancel” to drop all setting saved last

time.

11N Wireless Broadband Router

9.2 Traffic Statistics

Traffic statistics is used to show the LAN PC’s traffic information.

¾ Enable traffic statistics: check to enable traffic

statistics. Usually traffic statistics is disabled, which can improve the Router’s data handling. The default is disabled. If it is enabled, the page will update the PC’s traffic information automatically and be refreshed every 5 seconds.

¾ IP address: The IP address to be shown. ¾ Upstream rate: the speed of upstream data per

second (Kbyte/S).

¾ Downstream rate: the speed of downstream data

per second (Kbyte/S).

¾ Sending packet: The PC’s packets sending from

the PC.

¾ Sending byte: The byte (Mbyte) sending from the

PC.

¾ Receiving packet: The PC’s packets received

from the Router.

¾ Receiving byte: The PC’s byte (Mbyte) received

from the Router.

11N Wireless Broadband Router

Chapter10 URL Monitor

10.1 URL Monitor

This feature is used to record user’s Internet activity , so in terms of this feature, the administrator can check out and control what they can do and have done.

¾ Enable URL Monitor:

After checking this feature, the Router will record LAN computer’s URL information, including the visiting Website, your LAN IP address and the time. The Router can record up to 500 entries. If the record is more than 500 entries, the counter will clean all records and restart the URL record again. If the Router is powered off and restarts the device,

11N Wireless Broadband Router

the records will be also lost. The default setting is disabled.

¾ Enable Email: To enable this feature, the URL

records will be sent to specified e-mail, which can be solved the problem that the records will be lost when it is over 500 entries.

¾ Receive E-mail Address: Input the received

E-mail’s address here. For example:

tenda@sina.com.cn

¾ SMTP Server Address: Input the SMTP server

address here. If you are not clear what your SMTP server’s address is, you can find them from Help page of the registered e-mail. For example: smtp.sohu.com, smtp.163.com, etc.

¾ Send Email Address: Input the sending email

address here.

¾ User Name: Input the sending e-mail’s user

name.

¾ Email Password: Input the sending e-mail’s

password.

¾ Time Triggering Interval: To set sending

e-mail’s time interval. The time ranges from 30 to 1440 minutes. For example: if you input 30 here, it means the Router will send a email from “Send Email Address” to “Receive Email Address” in every 30 minutes. And then the device will clean all records and start the recording again.

11N Wireless Broadband Router

¾ Entry Triggering Interval: To set sending

e-mail’s entry interval. The entry ranges from 100 to 500. For example: if you input 100 here, it means the Router will send a email from “Send Email Address” to “Receive Email Address” in every 100 entries. And then the device will clean all records and start the recording again.

11N Wireless Broadband Router

Chapter 11: Security Settings

11.1 Client Filter Settings

To benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filter function.

¾ Client Filter: Check to enable client filter. ¾ Access Policy: Select one number from the

drop-down menu.

¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all

settings for the policy.

11N Wireless Broadband Router

¾ Filter Mode: Click one radio button to enable or

disable to access the Internet.

¾ Policy Name: Enter a name for the access policy

selected.

¾ IP Start/End: Enter the starting/ending IP

address.

¾ Port No.: Enter the port range based over the

protocol for access policy.

¾ Protocol: Select one protocol (TCP/UDP/Both)

from the drop-down menu.

¾ Times: Select the time range of client filter. ¾ Days: Select the day(s) to run the access policy.

11.2 URL Filter Settings

In order to control the computer to have access to websites, you can use URL filtering to allow the computer to have access to certain websites at fixed time and forbids it having access to certain websites at fixed time.

11N Wireless Broadband Router

¾ URL Filter: Check to enable URL filter. ¾ Access Policy: Select one number from the

drop-down menu.

¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all

settings for the policy.

¾ Filter Mode: Click one radio button to enable or

disable to access the Internet.

¾ Policy Name: Enter a name for the access policy

selected.

¾ Start/End IP: Enter the starting/ending IP

address.

¾ URL Strings: Specify the text strings or keywords

needed to be filtered. If any part of the URL contains these strings or words, the web page will not be accessible and displayed.

¾ Times: Select the time range of client filter. ¾ Days: Select the day(s) to run the access policy.

11N Wireless Broadband Router

11.3 MAC Address Filter

In order to manage the computers in LAN better, you could control the computer’s access to Internet by MAC Address Filter.

¾ MAC Address Filter: Check to enable MAC

address filter.

¾ Access Policy: Select one number from the

drop-down menu.

¾ Enable: Check to enable the access policy. ¾ Clear the Policy: Click “Clear” button to clear all

settings for the policy.

¾ Filter Mode: Click one radio button to enable or

disable to access the Internet.

¾ Policy Name: Enter a name for the access policy

selected.

11N Wireless Broadband Router

¾ MAC Address: Enter the MAC address you want to

run the access policy.

¾ Times: Select the time range of client filter. ¾ Days: Select the day(s) to run the access policy. ¾ Apply： Click to make the settings go i n to effect.

For example:

if you want to configure the host with MAC address 00:C0:9F: AD:FF:C5 not to access the Internet at 8：00-18：00, you need to set it as above.

11.4 Prevent Network Attack

This section is to protect the internal network from exotic attack such as SYN Flooding attack, Smurf attack, LAND attack, etc. Once detecting the unknown attack, the Router will restrict its bandwidth automatically. The attacker’s IP address can be found from the “System Log”.

¾ Prevent Network Attack: Check to enable it for

attack prevention.

11N Wireless Broadband Router

11.5 Remote Web Management

This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the “Enable”.

¾ Enable: Check to enable remote web

management.

¾ Port: The management port open to outside

access. The default value is 80.

¾ WAN IP Address: Specify the range of the WAN IP

address for remote management.

Note：

1. If you want to login the device’s Web-based interface via port 8080, you need use the format of WAN IP address: port (for example http://219.134.32.101: 8080) to implement remote login.

2. If your WAN IP address starts and ends with

11N Wireless Broadband Router

0.0.0.0, it means all hosts in WAN can implement remote Web management. If you change the WAN IP address as 218.88.93.33-218.88.93.35, then only the IP addresses as 218.88.93.33,

218.88.93.34 and 218.88.93.35 can access the Router .

For example: If you want to configure the IP address

218.88.93.33 to access the device’s web interface, please set it as follows:

11.6 Local Web Management

Local web management, the alternative to remote web management, is to allow the network administrator to manage the Router in LAN. Any PC in the LAN can access the Web management utility by default. So you can enter the specific MAC address of the LAN computer to function.

11N Wireless Broadband Router

¾ Enable: Check to enable the local web

management.

¾ MAC1/2/3…: Enter the MAC addresses of LAN

computers.

Note：

1. In the default state, this feature is not enabled. All computers in the LAN can login the Web.

2. For example, if you only allow the MAC address with 00:11:22:33:E4:F5 to access the Web, please set it as above.

11.7 WAN Ping

The ping test is to check the status of your internet connection. When disabling the test, the system will ignore the ping test from WAN.

¾ Ignore Ping from WAN:

Check to ignore the ping request and give no reply .

11N Wireless Broadband Router

Chapter12 Routing Setting

12.1 Routing Table

The main duty for a router is to look for a best path for every data frame, and transfer this data frame to a destination. So, it’s essential for the router to choose the best path, i.e. routing arithmetic. In order to finish this function, many transferring paths, i.e. routing table, are saved in the router, for choosing when needed.

12.2 Static Routing

This page is used to configure the Router’s static routing.

11N Wireless Broadband Router

¾ Destination LAN IP: The address of the remote

host with which you want to construct a static route.

¾ Subnet Mask: The network portion of the

Destination LAN IP.

¾ Gateway: The gateway of the next hop, usually

the Router or host’s IP address.

Note：

1. The gateway must keep the same segment with the Router’s LAN IP address.

2. If the destination IP address is one host’s IP address, the Subnet mask should be

255.255.255.255.

3. If the destination IP address is an IP address range, the subnet mask should match the IP address. For example, if the IP is 10.0.0.0, subnet mask should be 255.0.0.0; if the IP is 10.1.2.0, subnet mask should be 255.255.255.0.

11N Wireless Broadband Router

Chapter 13 System Tools

13.1 Time Settings

This section is to select the time zone for your location. If you turn off the Router , the settings for time disappear. However, the Router will automatically obtain the GMT time again once it has access to the Internet.

¾ Time Zone: Select your time zone from the

drop-down menu.

¾ Customized time: Enter the time you customize.

Note：

When the Router is powered off, the time setting will be lost. Before the Router will obtain GMT time automatically, you need connect with the Internet and obtain the GMT time, or set the time on this page first. Then the time in other features (e.g. firewall) can be activated.

11N Wireless Broadband Router

13.2 DDNS

The DDNS (Dynamic Domain Name System) is supported in this Router. It is to assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind the Router. If you want to activate this function, please select “Enable” and a DDNS service provider to sign up.

¾ Main Features:

Owing to ISP most times provides dynamic IP address, DDNS is used to capture the changeable IP address and match the fixed domain. Then users can have access to the Internet to communicate with others. DDNS can help you establish virtual host in your home and company.

¾ DDNS: Click the radio button to enable or disable

the DDNS service.

¾ Service Provider: Select one from the drop-down

11N Wireless Broadband Router

menu and press “Sign up” for registration.

¾ User Name: Enter the user name the same as the

registration name.

¾ Password: Enter the password you set. ¾ Domain Name: Enter the domain name which is

optional.

For example：

In the local host 192.168.0.10 establish a Web server, and register in 3322.org as follows:

User name tenda Password 123456 Domain Name tenda.vicp.net

After mapping the port in the virtual server, setting account informatio n in D DN S se rv e r a nd in th e a dd re ss field entering http://tenda.3322.org the Web page.

, you can access

11N Wireless Broadband Router

13.3 Backup/Restore Settings

The device provides backup/restore settings, so you need set a directory to keep these parameters.

¾ Backup Setting：

Click “Backup” button to back up the Router’s settings and select the path for save.

Click “Save” to save the configuration files.

11N Wireless Broadband Router

¾ Restore Setting：

Click “Browse” button to select the backup files.

Click “Restore” button to restore previous settings.

11N Wireless Broadband Router

13.4 Restore to Factory Default Setting

This button is to reset all settings to the default values. It means the Router will lose all the settings you have set. So please Note down the related settings if necessary.

¾ Restore: Click this button to restore to default

settings.

¾ Factory Default Settings:

User Name: admin Password: admin IP Address: 192.168.0.1 Subnet Mask: 255.255.255.0

NOTE:

After restoring to default settings, please restart the device, then the default settings can go into effect.

11N Wireless Broadband Router

13.5 Upgrade Firmware

The Router provides the firmware upgrade by clicking the “Upgrade” after browsing the firmware upgrade packet which you can download from www.tenda.cn

¾ Browse: click this button to select the upgrade file. ¾ Upgrade: click this button to start the upgrading

process. After the upgrade is completed, the Router will reboot automatically.

13.6 Reboot the Router

Rebooting the Router makes the settings configured go into effect or to set the Router again if setting failure happens.

Reboot the router: Click this button to reboot the device.

11N Wireless Broadband Router

13.7 Password Change

This section is to set a new user name and password to better secure your router and network.

¾ User Name: Enter a new user name for the device. ¾ Old Password: Enter the old password. ¾ New Password: Enter a new password. ¾ Re-enter to Confirm: Re-enter to confirm the

new password.

NOTE:

It is highly recommended to change the password to secure your network and the Router.

11N Wireless Broadband Router

13.8 System Log

The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown information. If the log is over 150 records, it will clear them automatically.

¾ Refresh: Click this button to update the log. ¾ Clear: Click this button to clear the current shown

log.

13.9 Logout

After you have finished the settings completely, in logout page click “Yes” to logout the web management page.

11N Wireless Broadband Router

Appendix 1：Glossary

Access Point (AP):

Any entity that has station functionality and provides access to the distribution services, via the wireless medium (WM) for associated stations.

Channel: An instance of medium use for the purpose of passing protocol data units (PDUs) that may be used simultaneously , in the s ame volume of space, with other instances of medium use(on other channels) by other instances of the same physical layer (PHY),with an acceptably low frame error ratio(FER) due to mutual interference.

SSID: Service Set identifier. An SSID is the network name shared by all devices in a wireless network. Your network’s SSID should be unique to your network and identical for all devices within the network. It is case-sensitive and must not exceed 20 characters (use any of the characters on the keyboard).Make sure this setting is the same for all devices in your wireless network.

11N Wireless Broadband Router

WEP: Wired Equivalent Privacy (WEP) is the method for secure wireless data transmission. WEP adds data encryption to every single packet transmitted in the wireless network. The 40bit and 64bit encryption are the same because of out 64 bits, 40 bits are private. Conversely, 104 and 128 bit are the same. WEP uses a common KEY to encode the data. Therefore, all devices on a wireless network must use the same key and same type of encryption. There are 2 methods for entering the KEY; one is to enter a 16-bit HEX digit. Using this method, users must enter a 10-digit number (for 64-bit) or 26-digit number (for 128-bit) in the KEY field. Users must select the same key number for all devices. The other method is to enter a text and let the computer generate the WEP key for you. However, since each product use different method for key generation, it might not work for different products. Therefore, it is NOT recommended using.

WPA/WPA2:

A security protocol for wireless networks that builds on the basic foundations of WEP. It secures wireless data transmission by using a key similar to WEP, but the added strength of WPA is that the key changes dynamically. The changing key makes it much more

11N Wireless Broadband Router

difficult for a hacker to learn the key and gain access to the network.WPA2 is the second generation of WPA security and provides a stronger encryption mechanism through Advanced Encryption Standard (AES), which is a requirement for some government users.

11N Wireless Broadband Router

Appendix 2: Ask and Question

In this part some questions and problems shown during the Router’s usage and installation will be given suggesting answers. If your problems are not in the list, please log into our website www.tenda.cn E-mail to support@tenda.cn, and we will reply you in the first time.

1、Can not login to the Web interface of the Router after you enter the IP address in the address field？

Step 1: check the Router if it works well. Once the device is powered on for a few seconds, the SYS indicator on the panel will be turned on. If it is not, please contact us.

Step 2: check the network cables if it is good and the corresponding indicator is “Always ON” . Sometimes, the indicator is “Always ON”, but it does not mean it gets through.

Run “Ping” command and check if it can ping the Router’s LAN IP address 192.168.0.1. If it is OK, please make sure your browser does not access the Internet by proxy server . If the ping fails, you can press the “RESET”

or send an

11N Wireless Broadband Router

button for 7 seconds to restore to default settings. And then repeat the ping operation. If it still does not work, please contact us.

2、 Forget the login password and can not enter the setting page. What can I do?

Press the “RESET” button for 7 seconds to restore the Router to default settings.

3、The computer connected with the Router shows IP address conflict. What can I do?

Check if there are other DHCP servers in the LAN. If there have, disable them. The default IP address of the Router is 192.168.0.1 and please maker sure the address is not occupied by other devices. If there are two computers with the same IP addresses, please modify one.

4、I can not use E-mail and access the Internet. What can I do?

It happens in ADSL connection and Dynamic IP users. And you need modify the default MTU value (1492). Please in the “WAN Setting” modify the MTU value with

11N Wireless Broadband Router

the recommended value as 1450 or 1400. 5 、 How to configure and access the Internet via Dynamic IP?

In Setup Wizard of the Web utility interface, select “Dynamic IP” connection type and click “Save” to activate it. As some ISPs bind the user computer’s MAC address, you need to clone the Router’s WAN MAC address to the bind21ing PC’s MAC address. Select “MAC Address Clone” in “Advanced Setting” to input your computer’s MAC address and click “Apply” to activate it.

6、How to share my computer’s source with other users in Internet？

If you want Internet users to access the internal server via the Router such as e-mail server, Web, FTP, you can configure the “Virtual Server” to come true. Step 1: create your internal server, make sure the LAN users can access these servers and know related service port. For example, Web server’s port is 80; FTP is 21; SMTP is 25 and POP3 is 110. Step 2: in the Router’s web click “Virtual Server” and select “Single Port Forwarding”. Step 3: input the external service port given by the Router, for example, 80.

11N Wireless Broadband Router

Step 4: input the internal Web service port, for example,

80. Step 5: Input the internal server’s IP address. If your Web server’s IP address is 192.168.0.10, please input it. Step 6: select the communication protocol used by your internal host: TCP, UDP, ICMP. Step 7: click “Apply” to activate the settings. The following table has listed the well-known application and service port:

Server Protocol Service Port WEB Server TCP 80 FTP Server TCP 21 Telnet TCP 23 NetMeeting TCP 1503、1720

File MSN Messenger

PPTP VPN TCP 1723 Iphone5.0 TCP 22555 SMTP TCP 25 POP3 TCP 110

TCP/UDP

Send:6891-6900(TCP)

Voice:1863、6901(TCP)

Voice:1863、5190(UDP)

11N Wireless Broadband Router

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful int erference in a residential installatio n. This equipm ent generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. T o assure conti nued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).

11N Wireless Broadband Router

“The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules. Operation is subject to the following two conditions:

1) This device may not cause interference and

2) This device must accept any interference, including interference that may cause undesired operation of the device.

This device must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

Caution!

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

TENDA TECHNOLOGY W307R Users Manual

Specifications and Main Features

Frequently Asked Questions

User Manual