Tenda W54M User Manual

W54P/W54P+ User Guide

W54P/W54P+ User Guide

Copyright Statement

is the registered trademark of
Shenzhen Tenda Technology Co., Ltd. All the products
and product names mentioned herein are the
trademarks or registered trademarks of their
respective holders. Copyright of the whole product as
integration, including its accessories and software,
belongs to Shenzhen Tenda Technology Co., Ltd.
Without the permission of Shenzhen T enda T e chnology
Co. , Ltd, any individual or party is not allowed to copy ,
plagiariz e, imita te or t ra nslate it into ot her lan guage s.

All the phot os and p roduct s pecificat ions me ntioned in
this guide are for references only. As the upgrade of
software and hardware, there will be changes. And if
there are changes, Tenda is not responsible for
informing in advanc e. If you w ant to know mo re about
our product information, please visit our website at
www.tenda.cn

.

W54P/W54P+ User Guide

Table of Content

Chapter 1 Introduction........................................1

1.1 Product Feature .......................................1

1.2 Product Deployment.................................3

1.3 Package Contents.....................................4

Chapter 2 Installation Guide.................................5

Chapter 3 Client Utility Interface…………………………….10

3.1 Station Mode .........................................11

3.1.1 Station Mode Topology ......................11

3.1.2 Status ............................................12

3.1.3 Site Survey .....................................13

3.1.4 Profile Management ..........................14

3.1.5 Statistics.........................................16

3.1.6 WPS Setting ....................................16

3.2 .............................................18 AP Mode

3.2.1 ............................18 AP Mode Topology

3.2.2 Basic Setting ..................................19

3.2.3 Security Setting ...............................20

3.2.4 Access Control.................................21

3.2.5 About.............................................23

Appendix One: Acronyms and Terms ................... 24

Appendix Two: How to connect with PSP..............27

W54P/W54P+ User Guide

Chapter 1 Introduction

W54P/W54P+ Wireless PCI Adapter complies with
IEEE802.11b, IEEE 802.11g standards with up to
54Mbps wireless transmission rate which is five times
ordinary IEEE802.11b products. It also supports
64/128-bit WEP, WPA/WPA-PSK, WPA2/WPA2-PSK
encryption and 802.1x security authentication
standard to secure your wireless networking. External
Omni-directional antenna frees you from the wired
cabling troubles and improves convenience and
flexibility of the wireless utility for fast and mobile
network sharing.

Soft AP supported by W54P/W54P+ can help you
establish wireless LAN networking with lowest cost.
Besides, PBC and PIN encryption methods (WPS, Wi-Fi
Protected Setup) can free you from remembering the
long passwords. Moreover, complete WMM support
makes your voice and video more smooth. Especially
supporting PSP, NDS and WII connections with Xlink
Kai will be your best choice to enjoy on-line games.

-1-

W54P/W54P+ User Guide

Note:

The only difference between W54P and

W54P+ is that W54P+’s antenna can be
detachable.

1.1 Product Feature

 Supports IEEE 802.11g and IEEE 802.11b

standards

 Provides two work modes: Infrastructure

mode and Ad-Hoc mode

 Provides up to 54Mbps maximum transmission

rate and up to 300m maximum transmission
range

 Auto-detects and changes the network

transmission rate

 Supports Soft AP; PSP, NDS and WII

connections with Internet and Xlink Kai

 Supports access control over MAC address in

Soft AP mode

 Supports WPS (Wi-Fi Protected Setup)

encryption method to free you from
remembering long passwords

 Provides simple configuration and monitoring

-2-

W54P/W54P+ User Guide

program

 Supports wireless Roaming function
 Supports WMM to make your voice and video

more smooth

 Easy-to-install, plug and play

1.2 Product Deployment

W54P/W54P+ Wireless PCI Adapter offers fast,
reliable and cost-effective solution for wireless
access. Deployment as follows:

 For staff who requires higher mobility in the

office, they want to have access to traditional
wired or wireless network in any place of the
company;

 Enterprise or individual who requires often

changes in lay out of network cables;

 Companies or places which are not suitable for

LAN cable laying out because of budget or
objective building, including places of great
interests, rent places or places for short-term

-3-

W54P/W54P+ User Guide

usage;

 Company or individual who avoids using

expensive cables, renting cables or renting
rights for access.

1.3 LED Indicator Description

On W54P/W54P+’s front panel, there is one LED
indicator blinking when the device is transmitting and
receiving data.

1.4 Package Contents

Unpack the packets, and please find the following
items:

 One W54P/W54P+ Wireless PCI Adapter
 One CD-ROM

-4-

W54P/W54P+ User Guide

Chapter 2 Installation Guide

This chapter is to assist you how to use the included
CD-ROM which comprises the Setup Wizard and the
Client Utility Interface.

The following steps on Setup Wizard are taken
Windows XP as example.

1. Please insert the Wireless PCI Adapter into the

PCI slot of your computer.

2. “Found New Hardware” system dialogue appears,
and selects “Cancel” to use the included Setup Wizard
for fast installation; of course, you also can select
“Next” to install by manual.

-5-

W54P/W54P+ User Guide

3. Inert the included CD-ROM into the CD-ROM
drive of your computer. (If not appear, double
click the “Setup.exe” icon.)

-6-

W54P/W54P+ User Guide

4. Click “Next” to start installing.

5. Click “Change…” to select the directory path, or
click “Next”.

-7-

W54P/W54P+ User Guide

6. Select “OK” and “Next” in the following window.

7. During the installation, the following dialogue

maybe appears. Click the “Continue Anyway” to
continue. There is no security threat to your
computer.

-8-

W54P/W54P+ User Guide

8. Click “Finish” to complete the installation.

-9-

W54P/W54P+ User Guide

Chapter 3 Client Utility Interface

The included client utility is for the W54P/W54P+
Wireless PCI Adapter management. If it does not
appear, select “Start”—“All Programs” —“TENDA”
—“ W54P/W54P+”, or click the shortcut on your PC’s
desktop.

Note:

In the Windows XP, you can select the included
W54P/W54P+ Client Utility Interface or the
Windows XP internal wireless application to
configure the device.

There are two client utility applications in W54P/
W54P+: Station Mode and AP Mode.

Note:

In this ut ility int erface, St ation Mode (Client M ode)
is the default access way.

-10-

W54P/W54P+ User Guide

3.1 Station Mode

3.1.1 Station Mode Topology

In this mode, W54P/W54P+ serves as a client to
receive the wireless signals to access the Internet.

-1

1-

W54P/W54P+ User Guide

3.1.2 Status

In the Network Status window, it displays something
on wireless adapter and wireless network’s status,
including SSID, Authentication type, Encryption Type,
IP address, subnet mask and gateway and so on.

-12-

W54P/W54P+ User Guide

3.1.3 Site Survey

The Site Survey is used to scan the available wireless
network around, showing the wireless network’s signal
strength and other information which provides basis
for you to access which wireless network.

Connect: select one entry in the wireless network
list and click the button to connect the device with
the selected network.
Refresh: rescan the wireless network around.

-13-

W54P/W54P+ User Guide

3.1.4 Profile Management

This window saves the general wireless parameters for
different profiles, which is used to fast connect the
wireless network you need.

UP/DOWN: To change the profile’s sequence in
the list.

Connect: To activate one profile.
New: To create a new profile and configure the

site status and security setting.

Modify: To modify one existing profile.
Delete: To delete one existing profile.

-14-

W54P/W54P+ User Guide

(Site Status)

(Security Setting)

-15-

W54P/W54P+ User Guide

3.1.5 Statistics

Statistics is used to summarize Rx and Tx data packets,
including the success and error packet amount.

Clear: click this button to renew the statistics.

3.1.6 WPS Setting

WPS setting is enabled only on WPS-compliant
devices.

-16-

W54P/W54P+ User Guide

PIN： Enter the Pin code and click the “PIN” to
automatically connect the wireless adapter with
wireless devices around.
PBC： Click the “PBC” to complete auto-check and
connections between wireless adapter and other
wireless device.

Refresh: to update the Pin code.
Rescan: to rescan the WPS-compliant wireless

network around.
Connect: click this button to connect the WPS
wireless network.
Disconnect: to disconnect the connected wireless
network.

-17-

W54P/W54P+ User Guide

3.2 AP Mode

3.2.1 AP Mode Topology

The device also can serve as an access point to
transmit wireless signals and create wireless network,
allowing other wireless clients to access the network.

Click the AP Mode icon to enter the AP Mode interface.

-18-

W54P/W54P+ User Guide

3.2.2 Basic Setting

This window is used to configure the AP’s basic para­meters, including SSID, Wireless Mode and Channel.

SSID: Wireless network’s ID name scanned by
wireless adapter.
Wireless Mode: 802.11b/802.11g/802.11b/g
mixed.

Channel: 1~11 channels provided.
Restore Default: to restore the set parameters to

default factory default settings.
Apply: to make the changes take effect.

-19-

W54P/W54P+ User Guide

3.2.3 Security Setting

This window is used to configure the wireless
network’s security authentication, providing WEP,
WPA-PSK, WPA2-PSK, and WPA-PSK/WPA2-PSK
encryption methods.

WEP：10/26 bits Hex or 5/13 ASCII support.
WPA-PSK：8~32 bits ASCII support.
WPA2-PSK：8~32 bits ASCII support.
WPA-PSK/WPA2-PSK：8~32 bits ASCII support.

-20-

W54P/W54P+ User Guide

Note:

1. The Hex characters include 0~9 numbers and

a~f letters.

2. ASCII characters include any numbers/letters

and characters.

3.2.4 Access Control

Access Control is based on the MAC address to decide
that the specified client connects to the wireless
network, or disables it to access the wireless network.

-21-

W54P/W54P+ User Guide

-22-

Filter Policy:

Di

sabled: to disable the filter function.

All Permitted: to permit a ll clients in the list t o

access the wireless network.
All Blocked: to refuse all clients in the list to

access the wireless network.
MAC Address：to input the client’s MAC address to
implement the corresponding filter policy. For
example: b0000a8cd702.

Add: to add the entered MAC address into the list.
Delete: to delete one existing MAC address in the

list.
Remove All: to delete all clients’ MAC address in
the list.
Apply: to make the changes take effect.

W54P/W54P+ User Guide

3.2.5 About

This window displays something about software
version and wireless adapter.

-23-

W54P/W54P+ User Guide

-24-

Appendix One: Acronyms and Terms

WLAN Wireless Local Area Network

802.11 A family of specifications developed by

the IEEE for WLAN technology.

802.11a An extension to 802.11 WLAN standard
that provides up to 54 Mbps transmis­sion in the 5 GHz UNI radio band.

802.11b An extension to 802.11 WLAN standard
that provides up to 11 Mbps
transmission in the 2.4 GHz ISM radio
band. 802.11b uses DSSS modulation.

802.11g An extension to 802.11 WLAN standard
that provides up to 54 Mbps
transmission in the 2.4 GHz ISM radio
band. 802.11b uses OFDM modulation
and is backwards compatible with

802.11b.

Ad-Hoc A group of computers each with wireless

adapters, connected as an independent
WLAN.

AES Advanced Encryption Standard

W54P/W54P+ User Guide

-25-

BSSID

Basic Service Set ID

DHCP Dynamic Host Configuration Protocol
DSSS Direct Sequence Spread Spectrum.

DSSS is one of two types of spread
spectrum radio. The other is
frequency-hopping spread spectrum
(FHSS).

QoS Quality of Service
OFDM Orthogonal Frequency Division

Multiplexing

RADIUS Remote Authentication Dial In User

Service

RTS Request to Send
SSID Service Set Identifier. A 32-character

unique identifier attached to the header
of packets sent over a WLAN that acts as
a password when a mobile device tries
to connect to the BSS.

TCP/IP Transmission Control Protocol/Internet

Protocol

TKIP Temporal Key Integrity Protocol
WDS Wireless Distribution System

W54P/W54P+ User Guide

-26-

WEP Wi

red Equivalent Privacy. A security

protocol for

WLANs defined in the IEEE 802.11

standard.

WPA Wi-Fi Protected Access
WPA2 Wi-Fi Protected Access 2. The next

generation of

Wi-Fi security, based on the 802.11i

standard.

WPA2-PSK Wi-Fi Protected Access 2-Pre-shared

Keys

WPA-PSK Wi-Fi Protected Access-Pre-shared Keys

W54P/W54P+ User Guide

-27-

Appendix Two: Product Specification

Standard IEEE802.11g, IEEE802.11b
Port 32-bit PCI 2.2 interface

Frequency Range 2.4～2.4835GHz

Transmission Rate

54 Mbps, 48 Mbps, 36 Mbps,
24 Mbps, 18 Mbps, 12 Mbps,
9 Mbps, 6 Mbps;
11 Mbps, 5.5 Mbps, 2 Mbps, 1
Mbps

Antenna Gain 2.2dBi

Transmission
Power

B mode: 20dbm (Max.)
G mode: 15dbm (Max.)

Modulation Method

OFDM, CCK

Working
Temperature

0℃～40℃

Storage
Temperature

-40℃～70℃

Working Humidity 10％～90％RH non-condensing

W54P/W54P+ User Guide

Appendix Three: How to connect with
PSP

1. Topology of PSP connecting with W54P

/W54P+

2. To configure PSP with Ad-Hoc mode

Select Network Settings

-28-

W54P/W54P+ User Guide

Select Ad-Hoc mode

Select Channel

-29-

W54P/W54P+ User Guide

3. In W54P/W54P+ Utility Interface scan PSP

and double-click to connect the wireless
network.

-30-

W54P/W54P+ User Guide

4. In Site Survey check “enable PSP connection

mode” box.

5. To configure Xlink Kai

Select “Start”→ “All programmers” → “Xlink Kai
Evolution VII” → “Start Kai Config” to configure the
user name, password and other parameters as
follows.

-31-

W54P/W54P+ User Guide

6. Login Xlink Kai

Select “Start”→ “All programmers” → “Xlink Kai
Evolution VII” → “Start Ka i”. PSP will connect with
Xlink Kai automatically. The following window will
indicate the connection is established well now.

-32-